| /* |
| This is part of the rtl8180-sa2400 driver |
| released under the GPL (See file COPYING for details). |
| Copyright (c) 2005 Andrea Merello <andreamrl@tiscali.it> |
| |
| This files contains programming code for the rtl8225 |
| radio frontend. |
| |
| *Many* thanks to Realtek Corp. for their great support! |
| |
| */ |
| |
| #include "r8180_hw.h" |
| #include "r8180_rtl8225.h" |
| #include "r8180_93cx6.h" |
| |
| #ifdef ENABLE_DOT11D |
| #include "dot11d.h" |
| #endif |
| |
| #ifdef CONFIG_RTL8185B |
| |
| extern u8 rtl8225_agc[]; |
| |
| extern u32 rtl8225_chan[]; |
| |
| //2005.11.16 |
| u8 rtl8225z2_threshold[]={ |
| 0x8d, 0x8d, 0x8d, 0x8d, 0x9d, 0xad, 0xbd, |
| }; |
| |
| // 0xd 0x19 0x1b 0x21 |
| u8 rtl8225z2_gain_bg[]={ |
| 0x23, 0x15, 0xa5, // -82-1dbm |
| 0x23, 0x15, 0xb5, // -82-2dbm |
| 0x23, 0x15, 0xc5, // -82-3dbm |
| 0x33, 0x15, 0xc5, // -78dbm |
| 0x43, 0x15, 0xc5, // -74dbm |
| 0x53, 0x15, 0xc5, // -70dbm |
| 0x63, 0x15, 0xc5, // -66dbm |
| }; |
| |
| u8 rtl8225z2_gain_a[]={ |
| 0x13,0x27,0x5a,//,0x37,// -82dbm |
| 0x23,0x23,0x58,//,0x37,// -82dbm |
| 0x33,0x1f,0x56,//,0x37,// -82dbm |
| 0x43,0x1b,0x54,//,0x37,// -78dbm |
| 0x53,0x17,0x51,//,0x37,// -74dbm |
| 0x63,0x24,0x4f,//,0x37,// -70dbm |
| 0x73,0x0f,0x4c,//,0x37,// -66dbm |
| }; |
| #if 0 |
| u32 rtl8225_chan[] = { |
| 0, //dummy channel 0 |
| 0x085c, //1 |
| 0x08dc, //2 |
| 0x095c, //3 |
| 0x09dc, //4 |
| 0x0a5c, //5 |
| 0x0adc, //6 |
| 0x0b5c, //7 |
| 0x0bdc, //8 |
| 0x0c5c, //9 |
| 0x0cdc, //10 |
| 0x0d5c, //11 |
| 0x0ddc, //12 |
| 0x0e5c, //13 |
| //0x0f5c, //14 |
| 0x0f72, // 14 |
| }; |
| #endif |
| |
| //- |
| u16 rtl8225z2_rxgain[]={ |
| 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409, |
| 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541, |
| 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583, |
| 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644, |
| 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688, |
| 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745, |
| 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789, |
| 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793, |
| 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d, |
| 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9, |
| 0x03aa, 0x03ab, 0x03ac, 0x03ad, 0x03b0, 0x03b1, 0x03b2, 0x03b3, |
| 0x03b4, 0x03b5, 0x03b8, 0x03b9, 0x03ba, 0x03bb, 0x03bb |
| |
| }; |
| |
| //2005.11.16, |
| u8 ZEBRA2_CCK_OFDM_GAIN_SETTING[]={ |
| 0x00,0x01,0x02,0x03,0x04,0x05, |
| 0x06,0x07,0x08,0x09,0x0a,0x0b, |
| 0x0c,0x0d,0x0e,0x0f,0x10,0x11, |
| 0x12,0x13,0x14,0x15,0x16,0x17, |
| 0x18,0x19,0x1a,0x1b,0x1c,0x1d, |
| 0x1e,0x1f,0x20,0x21,0x22,0x23, |
| }; |
| |
| #if 0 |
| //- |
| u8 rtl8225_agc[]={ |
| 0x9e,0x9e,0x9e,0x9e,0x9e,0x9e,0x9e,0x9e,0x9d,0x9c,0x9b,0x9a,0x99,0x98,0x97,0x96, |
| 0x95,0x94,0x93,0x92,0x91,0x90,0x8f,0x8e,0x8d,0x8c,0x8b,0x8a,0x89,0x88,0x87,0x86, |
| 0x85,0x84,0x83,0x82,0x81,0x80,0x3f,0x3e,0x3d,0x3c,0x3b,0x3a,0x39,0x38,0x37,0x36, |
| 0x35,0x34,0x33,0x32,0x31,0x30,0x2f,0x2e,0x2d,0x2c,0x2b,0x2a,0x29,0x28,0x27,0x26, |
| 0x25,0x24,0x23,0x22,0x21,0x20,0x1f,0x1e,0x1d,0x1c,0x1b,0x1a,0x19,0x18,0x17,0x16, |
| 0x15,0x14,0x13,0x12,0x11,0x10,0x0f,0x0e,0x0d,0x0c,0x0b,0x0a,0x09,0x08,0x07,0x06, |
| 0x05,0x04,0x03,0x02,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, |
| 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, |
| }; |
| #endif |
| /* |
| from 0 to 0x23 |
| u8 rtl8225_tx_gain_cck_ofdm[]={ |
| 0x02,0x06,0x0e,0x1e,0x3e,0x7e |
| }; |
| */ |
| |
| //- |
| u8 rtl8225z2_tx_power_ofdm[]={ |
| 0x42,0x00,0x40,0x00,0x40 |
| }; |
| |
| |
| //- |
| u8 rtl8225z2_tx_power_cck_ch14[]={ |
| 0x36,0x35,0x2e,0x1b,0x00,0x00,0x00,0x00 |
| }; |
| |
| |
| //- |
| u8 rtl8225z2_tx_power_cck[]={ |
| 0x36,0x35,0x2e,0x25,0x1c,0x12,0x09,0x04 |
| }; |
| |
| |
| void rtl8225z2_set_gain(struct net_device *dev, short gain) |
| { |
| u8* rtl8225_gain; |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| |
| u8 mode = priv->ieee80211->mode; |
| |
| if(mode == IEEE_B || mode == IEEE_G) |
| rtl8225_gain = rtl8225z2_gain_bg; |
| else |
| rtl8225_gain = rtl8225z2_gain_a; |
| |
| //write_phy_ofdm(dev, 0x0d, rtl8225_gain[gain * 3]); |
| //write_phy_ofdm(dev, 0x19, rtl8225_gain[gain * 3 + 1]); |
| //write_phy_ofdm(dev, 0x1b, rtl8225_gain[gain * 3 + 2]); |
| //2005.11.17, by ch-hsu |
| write_phy_ofdm(dev, 0x0b, rtl8225_gain[gain * 3]); |
| write_phy_ofdm(dev, 0x1b, rtl8225_gain[gain * 3 + 1]); |
| write_phy_ofdm(dev, 0x1d, rtl8225_gain[gain * 3 + 2]); |
| write_phy_ofdm(dev, 0x21, 0x37); |
| |
| } |
| |
| #if 0 |
| |
| void rtl8225_set_gain(struct net_device *dev, short gain) |
| { |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| |
| rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON); |
| |
| if(priv->card_8185 == 2) |
| write_phy_ofdm(dev, 0x21, 0x27); |
| else |
| write_phy_ofdm(dev, 0x21, 0x37); |
| |
| write_phy_ofdm(dev, 0x25, 0x20); |
| write_phy_ofdm(dev, 0x11, 0x6); |
| |
| if(priv->card_8185 == 1 && priv->card_8185_Bversion) |
| write_phy_ofdm(dev, 0x27, 0x8); |
| else |
| write_phy_ofdm(dev, 0x27, 0x88); |
| |
| write_phy_ofdm(dev, 0x14, 0); |
| write_phy_ofdm(dev, 0x16, 0); |
| write_phy_ofdm(dev, 0x15, 0x40); |
| write_phy_ofdm(dev, 0x17, 0x40); |
| |
| write_phy_ofdm(dev, 0x0d, rtl8225_gain[gain * 4]); |
| write_phy_ofdm(dev, 0x23, rtl8225_gain[gain * 4 + 1]); |
| write_phy_ofdm(dev, 0x1b, rtl8225_gain[gain * 4 + 2]); |
| write_phy_ofdm(dev, 0x1d, rtl8225_gain[gain * 4 + 3]); |
| //rtl8225_set_gain_usb(dev, gain); |
| } |
| #endif |
| |
| u32 read_rtl8225(struct net_device *dev, u8 adr) |
| { |
| u32 data2Write = ((u32)(adr & 0x1f)) << 27; |
| u32 dataRead; |
| u32 mask; |
| u16 oval,oval2,oval3,tmp; |
| // ThreeWireReg twreg; |
| // ThreeWireReg tdata; |
| int i; |
| short bit, rw; |
| |
| u8 wLength = 6; |
| u8 rLength = 12; |
| u8 low2high = 0; |
| |
| oval = read_nic_word(dev, RFPinsOutput); |
| oval2 = read_nic_word(dev, RFPinsEnable); |
| oval3 = read_nic_word(dev, RFPinsSelect); |
| |
| write_nic_word(dev, RFPinsEnable, (oval2|0xf)); |
| write_nic_word(dev, RFPinsSelect, (oval3|0xf)); |
| |
| dataRead = 0; |
| |
| oval &= ~0xf; |
| |
| write_nic_word(dev, RFPinsOutput, oval | BB_HOST_BANG_EN ); udelay(4); |
| |
| write_nic_word(dev, RFPinsOutput, oval ); udelay(5); |
| |
| rw = 0; |
| |
| mask = (low2high) ? 0x01 : (((u32)0x01)<<(32-1)); |
| for(i = 0; i < wLength/2; i++) |
| { |
| bit = ((data2Write&mask) != 0) ? 1 : 0; |
| write_nic_word(dev, RFPinsOutput, bit|oval | rw); udelay(1); |
| |
| write_nic_word(dev, RFPinsOutput, bit|oval | BB_HOST_BANG_CLK | rw); udelay(2); |
| write_nic_word(dev, RFPinsOutput, bit|oval | BB_HOST_BANG_CLK | rw); udelay(2); |
| |
| mask = (low2high) ? (mask<<1): (mask>>1); |
| |
| if(i == 2) |
| { |
| rw = BB_HOST_BANG_RW; |
| write_nic_word(dev, RFPinsOutput, bit|oval | BB_HOST_BANG_CLK | rw); udelay(2); |
| write_nic_word(dev, RFPinsOutput, bit|oval | rw); udelay(2); |
| break; |
| } |
| |
| bit = ((data2Write&mask) != 0) ? 1: 0; |
| |
| write_nic_word(dev, RFPinsOutput, oval|bit|rw| BB_HOST_BANG_CLK); udelay(2); |
| write_nic_word(dev, RFPinsOutput, oval|bit|rw| BB_HOST_BANG_CLK); udelay(2); |
| |
| write_nic_word(dev, RFPinsOutput, oval| bit |rw); udelay(1); |
| |
| mask = (low2high) ? (mask<<1) : (mask>>1); |
| } |
| |
| //twreg.struc.clk = 0; |
| //twreg.struc.data = 0; |
| write_nic_word(dev, RFPinsOutput, rw|oval); udelay(2); |
| mask = (low2high) ? 0x01 : (((u32)0x01) << (12-1)); |
| |
| // We must set data pin to HW controled, otherwise RF can't driver it and |
| // value RF register won't be able to read back properly. 2006.06.13, by rcnjko. |
| write_nic_word(dev, RFPinsEnable, (oval2 & (~0x01))); |
| |
| for(i = 0; i < rLength; i++) |
| { |
| write_nic_word(dev, RFPinsOutput, rw|oval); udelay(1); |
| |
| write_nic_word(dev, RFPinsOutput, rw|oval|BB_HOST_BANG_CLK); udelay(2); |
| write_nic_word(dev, RFPinsOutput, rw|oval|BB_HOST_BANG_CLK); udelay(2); |
| write_nic_word(dev, RFPinsOutput, rw|oval|BB_HOST_BANG_CLK); udelay(2); |
| tmp = read_nic_word(dev, RFPinsInput); |
| |
| dataRead |= (tmp & BB_HOST_BANG_CLK ? mask : 0); |
| |
| write_nic_word(dev, RFPinsOutput, (rw|oval)); udelay(2); |
| |
| mask = (low2high) ? (mask<<1) : (mask>>1); |
| } |
| |
| write_nic_word(dev, RFPinsOutput, BB_HOST_BANG_EN|BB_HOST_BANG_RW|oval); udelay(2); |
| |
| write_nic_word(dev, RFPinsEnable, oval2); |
| write_nic_word(dev, RFPinsSelect, oval3); // Set To SW Switch |
| write_nic_word(dev, RFPinsOutput, 0x3a0); |
| |
| return dataRead; |
| |
| } |
| #if 0 |
| void write_rtl8225(struct net_device *dev, u8 adr, u16 data) |
| { |
| int i; |
| u16 out,select; |
| u8 bit; |
| u32 bangdata = (data << 4) | (adr & 0xf); |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| |
| out = read_nic_word(dev, RFPinsOutput) & 0xfff3; |
| |
| write_nic_word(dev,RFPinsEnable, |
| (read_nic_word(dev,RFPinsEnable) | 0x7)); |
| |
| select = read_nic_word(dev, RFPinsSelect); |
| |
| write_nic_word(dev, RFPinsSelect, select | 0x7 | |
| ((priv->card_type == USB) ? 0 : SW_CONTROL_GPIO)); |
| |
| force_pci_posting(dev); |
| udelay(10); |
| |
| write_nic_word(dev, RFPinsOutput, out | BB_HOST_BANG_EN );//| 0x1fff); |
| |
| force_pci_posting(dev); |
| udelay(2); |
| |
| write_nic_word(dev, RFPinsOutput, out); |
| |
| force_pci_posting(dev); |
| udelay(10); |
| |
| |
| for(i=15; i>=0;i--){ |
| |
| bit = (bangdata & (1<<i)) >> i; |
| |
| write_nic_word(dev, RFPinsOutput, bit | out); |
| |
| write_nic_word(dev, RFPinsOutput, bit | out | BB_HOST_BANG_CLK); |
| write_nic_word(dev, RFPinsOutput, bit | out | BB_HOST_BANG_CLK); |
| |
| i--; |
| bit = (bangdata & (1<<i)) >> i; |
| |
| write_nic_word(dev, RFPinsOutput, bit | out | BB_HOST_BANG_CLK); |
| write_nic_word(dev, RFPinsOutput, bit | out | BB_HOST_BANG_CLK); |
| |
| write_nic_word(dev, RFPinsOutput, bit | out); |
| |
| } |
| |
| write_nic_word(dev, RFPinsOutput, out | BB_HOST_BANG_EN); |
| |
| force_pci_posting(dev); |
| udelay(10); |
| |
| write_nic_word(dev, RFPinsOutput, out | |
| ((priv->card_type == USB) ? 4 : BB_HOST_BANG_EN)); |
| |
| write_nic_word(dev, RFPinsSelect, select | |
| ((priv->card_type == USB) ? 0 : SW_CONTROL_GPIO)); |
| |
| if(priv->card_type == USB) |
| mdelay(2); |
| else |
| rtl8185_rf_pins_enable(dev); |
| } |
| |
| #endif |
| short rtl8225_is_V_z2(struct net_device *dev) |
| { |
| short vz2 = 1; |
| //int i; |
| /* sw to reg pg 1 */ |
| //write_rtl8225(dev, 0, 0x1b7); |
| //write_rtl8225(dev, 0, 0x0b7); |
| |
| /* reg 8 pg 1 = 23*/ |
| //printk(KERN_WARNING "RF Rigisters:\n"); |
| #if 0 |
| for(i = 0; i <= 0xf; i++) |
| printk(KERN_WARNING "%08x,", read_rtl8225(dev, i)); |
| //printk(KERN_WARNING "reg[9]@pg1 = 0x%x\n", read_rtl8225(dev, 0x0F)); |
| |
| // printk(KERN_WARNING "RF:\n"); |
| #endif |
| if( read_rtl8225(dev, 8) != 0x588) |
| vz2 = 0; |
| |
| else /* reg 9 pg 1 = 24 */ |
| if( read_rtl8225(dev, 9) != 0x700) |
| vz2 = 0; |
| |
| /* sw back to pg 0 */ |
| write_rtl8225(dev, 0, 0xb7); |
| |
| return vz2; |
| |
| } |
| |
| #if 0 |
| void rtl8225_rf_close(struct net_device *dev) |
| { |
| write_rtl8225(dev, 0x4, 0x1f); |
| |
| force_pci_posting(dev); |
| mdelay(1); |
| |
| rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_OFF); |
| rtl8185_set_anaparam2(dev, RTL8225_ANAPARAM2_OFF); |
| } |
| #endif |
| #if 0 |
| short rtl8225_rf_set_sens(struct net_device *dev, short sens) |
| { |
| if (sens <0 || sens > 6) return -1; |
| |
| if(sens > 4) |
| write_rtl8225(dev, 0x0c, 0x850); |
| else |
| write_rtl8225(dev, 0x0c, 0x50); |
| |
| sens= 6-sens; |
| rtl8225_set_gain(dev, sens); |
| |
| write_phy_cck(dev, 0x41, rtl8225_threshold[sens]); |
| return 0; |
| |
| } |
| #endif |
| |
| |
| void rtl8225z2_rf_close(struct net_device *dev) |
| { |
| RF_WriteReg(dev, 0x4, 0x1f); |
| |
| force_pci_posting(dev); |
| mdelay(1); |
| |
| rtl8180_set_anaparam(dev, RTL8225z2_ANAPARAM_OFF); |
| rtl8185_set_anaparam2(dev, RTL8225z2_ANAPARAM2_OFF); |
| } |
| |
| #ifdef ENABLE_DOT11D |
| // |
| // Description: |
| // Map dBm into Tx power index according to |
| // current HW model, for example, RF and PA, and |
| // current wireless mode. |
| // |
| s8 |
| DbmToTxPwrIdx( |
| struct r8180_priv *priv, |
| WIRELESS_MODE WirelessMode, |
| s32 PowerInDbm |
| ) |
| { |
| bool bUseDefault = true; |
| s8 TxPwrIdx = 0; |
| |
| #ifdef CONFIG_RTL818X_S |
| // |
| // 071011, SD3 SY: |
| // OFDM Power in dBm = Index * 0.5 + 0 |
| // CCK Power in dBm = Index * 0.25 + 13 |
| // |
| if(priv->card_8185 >= VERSION_8187S_B) |
| { |
| s32 tmp = 0; |
| |
| if(WirelessMode == WIRELESS_MODE_G) |
| { |
| bUseDefault = false; |
| tmp = (2 * PowerInDbm); |
| |
| if(tmp < 0) |
| TxPwrIdx = 0; |
| else if(tmp > 40) // 40 means 20 dBm. |
| TxPwrIdx = 40; |
| else |
| TxPwrIdx = (s8)tmp; |
| } |
| else if(WirelessMode == WIRELESS_MODE_B) |
| { |
| bUseDefault = false; |
| tmp = (4 * PowerInDbm) - 52; |
| |
| if(tmp < 0) |
| TxPwrIdx = 0; |
| else if(tmp > 28) // 28 means 20 dBm. |
| TxPwrIdx = 28; |
| else |
| TxPwrIdx = (s8)tmp; |
| } |
| } |
| #endif |
| |
| // |
| // TRUE if we want to use a default implementation. |
| // We shall set it to FALSE when we have exact translation formular |
| // for target IC. 070622, by rcnjko. |
| // |
| if(bUseDefault) |
| { |
| if(PowerInDbm < 0) |
| TxPwrIdx = 0; |
| else if(PowerInDbm > 35) |
| TxPwrIdx = 35; |
| else |
| TxPwrIdx = (u8)PowerInDbm; |
| } |
| |
| return TxPwrIdx; |
| } |
| #endif |
| |
| void rtl8225z2_SetTXPowerLevel(struct net_device *dev, short ch) |
| { |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| |
| // int GainIdx; |
| // int GainSetting; |
| //int i; |
| //u8 power; |
| //u8 *cck_power_table; |
| u8 max_cck_power_level; |
| //u8 min_cck_power_level; |
| u8 max_ofdm_power_level; |
| u8 min_ofdm_power_level; |
| // u8 cck_power_level = 0xff & priv->chtxpwr[ch];//-by amy 080312 |
| // u8 ofdm_power_level = 0xff & priv->chtxpwr_ofdm[ch];//-by amy 080312 |
| char cck_power_level = (char)(0xff & priv->chtxpwr[ch]);//+by amy 080312 |
| char ofdm_power_level = (char)(0xff & priv->chtxpwr_ofdm[ch]);//+by amy 080312 |
| #if 0 |
| // |
| // CCX 2 S31, AP control of client transmit power: |
| // 1. We shall not exceed Cell Power Limit as possible as we can. |
| // 2. Tolerance is +/- 5dB. |
| // 3. 802.11h Power Contraint takes higher precedence over CCX Cell Power Limit. |
| // |
| // TODO: |
| // 1. 802.11h power contraint |
| // |
| // 071011, by rcnjko. |
| // |
| if( priv->OpMode == RT_OP_MODE_INFRASTRUCTURE && |
| priv->bWithCcxCellPwr && |
| ch == priv->dot11CurrentChannelNumber) |
| { |
| u8 CckCellPwrIdx = DbmToTxPwrIdx(dev, WIRELESS_MODE_B, pMgntInfo->CcxCellPwr); |
| u8 OfdmCellPwrIdx = DbmToTxPwrIdx(dev, WIRELESS_MODE_G, pMgntInfo->CcxCellPwr); |
| |
| printk("CCX Cell Limit: %d dBm => CCK Tx power index : %d, OFDM Tx power index: %d\n", |
| priv->CcxCellPwr, CckCellPwrIdx, OfdmCellPwrIdx); |
| printk("EEPROM channel(%d) => CCK Tx power index: %d, OFDM Tx power index: %d\n", |
| channel, CckTxPwrIdx, OfdmTxPwrIdx); |
| |
| if(cck_power_level > CckCellPwrIdx) |
| cck_power_level = CckCellPwrIdx; |
| if(ofdm_power_level > OfdmCellPwrIdx) |
| ofdm_power_level = OfdmCellPwrIdx; |
| |
| printk("Altered CCK Tx power index : %d, OFDM Tx power index: %d\n", |
| CckTxPwrIdx, OfdmTxPwrIdx); |
| } |
| #endif |
| #ifdef ENABLE_DOT11D |
| if(IS_DOT11D_ENABLE(priv->ieee80211) && |
| IS_DOT11D_STATE_DONE(priv->ieee80211) ) |
| { |
| //PRT_DOT11D_INFO pDot11dInfo = GET_DOT11D_INFO(priv->ieee80211); |
| u8 MaxTxPwrInDbm = DOT11D_GetMaxTxPwrInDbm(priv->ieee80211, ch); |
| u8 CckMaxPwrIdx = DbmToTxPwrIdx(priv, WIRELESS_MODE_B, MaxTxPwrInDbm); |
| u8 OfdmMaxPwrIdx = DbmToTxPwrIdx(priv, WIRELESS_MODE_G, MaxTxPwrInDbm); |
| |
| //printk("Max Tx Power dBm (%d) => CCK Tx power index : %d, OFDM Tx power index: %d\n", MaxTxPwrInDbm, CckMaxPwrIdx, OfdmMaxPwrIdx); |
| |
| //printk("EEPROM channel(%d) => CCK Tx power index: %d, OFDM Tx power index: %d\n", |
| // ch, cck_power_level, ofdm_power_level); |
| |
| if(cck_power_level > CckMaxPwrIdx) |
| cck_power_level = CckMaxPwrIdx; |
| if(ofdm_power_level > OfdmMaxPwrIdx) |
| ofdm_power_level = OfdmMaxPwrIdx; |
| } |
| |
| //priv->CurrentCckTxPwrIdx = cck_power_level; |
| //priv->CurrentOfdmTxPwrIdx = ofdm_power_level; |
| #endif |
| |
| max_cck_power_level = 15; |
| max_ofdm_power_level = 25; // 12 -> 25 |
| min_ofdm_power_level = 10; |
| |
| #ifdef CONFIG_RTL8185B |
| #ifdef CONFIG_RTL818X_S |
| |
| if(cck_power_level > 35) |
| { |
| cck_power_level = 35; |
| } |
| // |
| // Set up CCK TXAGC. suggested by SD3 SY. |
| // |
| write_nic_byte(dev, CCK_TXAGC, (ZEBRA2_CCK_OFDM_GAIN_SETTING[(u8)cck_power_level]) ); |
| //printk("CCK TX power is %x\n", (ZEBRA2_CCK_OFDM_GAIN_SETTING[cck_power_level])); |
| force_pci_posting(dev); |
| mdelay(1); |
| #else |
| |
| /* CCK power setting */ |
| if(cck_power_level > max_cck_power_level) |
| cck_power_level = max_cck_power_level; |
| |
| cck_power_level += priv->cck_txpwr_base; |
| |
| if(cck_power_level > 35) |
| cck_power_level = 35; |
| |
| if(ch == 14) |
| cck_power_table = rtl8225z2_tx_power_cck_ch14; |
| else |
| cck_power_table = rtl8225z2_tx_power_cck; |
| |
| |
| for(i=0;i<8;i++){ |
| |
| power = cck_power_table[i]; |
| write_phy_cck(dev, 0x44 + i, power); |
| } |
| |
| //write_nic_byte(dev, TX_GAIN_CCK, power); |
| //2005.11.17, |
| write_nic_byte(dev, CCK_TXAGC, ZEBRA2_CCK_OFDM_GAIN_SETTING[(u8)cck_power_level]); |
| |
| force_pci_posting(dev); |
| mdelay(1); |
| #endif |
| #endif |
| /* OFDM power setting */ |
| // Old: |
| // if(ofdm_power_level > max_ofdm_power_level) |
| // ofdm_power_level = 35; |
| // ofdm_power_level += min_ofdm_power_level; |
| // Latest: |
| /* if(ofdm_power_level > (max_ofdm_power_level - min_ofdm_power_level)) |
| ofdm_power_level = max_ofdm_power_level; |
| else |
| ofdm_power_level += min_ofdm_power_level; |
| |
| ofdm_power_level += priv->ofdm_txpwr_base; |
| */ |
| if(ofdm_power_level > 35) |
| ofdm_power_level = 35; |
| |
| // rtl8185_set_anaparam2(dev,RTL8225_ANAPARAM2_ON); |
| |
| //rtl8185_set_anaparam2(dev, ANAPARM2_ASIC_ON); |
| |
| if (priv->up == 0) { |
| //must add these for rtl8185B down, xiong-2006-11-21 |
| write_phy_ofdm(dev,2,0x42); |
| write_phy_ofdm(dev,5,0); |
| write_phy_ofdm(dev,6,0x40); |
| write_phy_ofdm(dev,7,0); |
| write_phy_ofdm(dev,8,0x40); |
| } |
| |
| //write_nic_byte(dev, TX_GAIN_OFDM, ofdm_power_level); |
| //2005.11.17, |
| #ifdef CONFIG_RTL818X_S |
| write_nic_byte(dev, OFDM_TXAGC, ZEBRA2_CCK_OFDM_GAIN_SETTING[(u8)ofdm_power_level]); |
| #else |
| write_nic_byte(dev, OFDM_TXAGC, ZEBRA2_CCK_OFDM_GAIN_SETTING[(u8)ofdm_power_level]*2); |
| #endif |
| if(ofdm_power_level<=11) |
| { |
| // write_nic_dword(dev,PHY_ADR,0x00005c87); |
| // write_nic_dword(dev,PHY_ADR,0x00005c89); |
| write_phy_ofdm(dev,0x07,0x5c); |
| write_phy_ofdm(dev,0x09,0x5c); |
| } |
| if(ofdm_power_level<=17) |
| { |
| // write_nic_dword(dev,PHY_ADR,0x00005487); |
| // write_nic_dword(dev,PHY_ADR,0x00005489); |
| write_phy_ofdm(dev,0x07,0x54); |
| write_phy_ofdm(dev,0x09,0x54); |
| } |
| else |
| { |
| // write_nic_dword(dev,PHY_ADR,0x00005087); |
| // write_nic_dword(dev,PHY_ADR,0x00005089); |
| write_phy_ofdm(dev,0x07,0x50); |
| write_phy_ofdm(dev,0x09,0x50); |
| } |
| force_pci_posting(dev); |
| mdelay(1); |
| |
| } |
| #if 0 |
| /* switch between mode B and G */ |
| void rtl8225_set_mode(struct net_device *dev, short modeb) |
| { |
| write_phy_ofdm(dev, 0x15, (modeb ? 0x0 : 0x40)); |
| write_phy_ofdm(dev, 0x17, (modeb ? 0x0 : 0x40)); |
| } |
| #endif |
| |
| void rtl8225z2_rf_set_chan(struct net_device *dev, short ch) |
| { |
| /* |
| short gset = (priv->ieee80211->state == IEEE80211_LINKED && |
| ieee80211_is_54g(priv->ieee80211->current_network)) || |
| priv->ieee80211->iw_mode == IW_MODE_MONITOR; |
| */ |
| rtl8225z2_SetTXPowerLevel(dev, ch); |
| |
| RF_WriteReg(dev, 0x7, rtl8225_chan[ch]); |
| |
| //YJ,add,080828, if set channel failed, write again |
| if((RF_ReadReg(dev, 0x7) & 0x0F80) != rtl8225_chan[ch]) |
| { |
| RF_WriteReg(dev, 0x7, rtl8225_chan[ch]); |
| } |
| |
| mdelay(1); |
| |
| force_pci_posting(dev); |
| mdelay(10); |
| //deleted by David : 2006/8/9 |
| #if 0 |
| write_nic_byte(dev,SIFS,0x22);// SIFS: 0x22 |
| |
| if(gset) |
| write_nic_byte(dev,DIFS,20); //DIFS: 20 |
| else |
| write_nic_byte(dev,DIFS,0x24); //DIFS: 36 |
| |
| if(priv->ieee80211->state == IEEE80211_LINKED && |
| ieee80211_is_shortslot(priv->ieee80211->current_network)) |
| write_nic_byte(dev,SLOT,0x9); //SLOT: 9 |
| |
| else |
| write_nic_byte(dev,SLOT,0x14); //SLOT: 20 (0x14) |
| |
| |
| if(gset){ |
| write_nic_byte(dev,EIFS,91 - 20); // EIFS: 91 (0x5B) |
| write_nic_byte(dev,CW_VAL,0x73); //CW VALUE: 0x37 |
| //DMESG("using G net params"); |
| }else{ |
| write_nic_byte(dev,EIFS,91 - 0x24); // EIFS: 91 (0x5B) |
| write_nic_byte(dev,CW_VAL,0xa5); //CW VALUE: 0x37 |
| //DMESG("using B net params"); |
| } |
| #endif |
| |
| } |
| #if 0 |
| void rtl8225_host_pci_init(struct net_device *dev) |
| { |
| write_nic_word(dev, RFPinsOutput, 0x480); |
| |
| rtl8185_rf_pins_enable(dev); |
| |
| //if(priv->card_8185 == 2 && priv->enable_gpio0 ) /* version D */ |
| //write_nic_word(dev, RFPinsSelect, 0x88); |
| //else |
| write_nic_word(dev, RFPinsSelect, 0x88 | SW_CONTROL_GPIO); /* 0x488 | SW_CONTROL_GPIO */ |
| |
| write_nic_byte(dev, GP_ENABLE, 0); |
| |
| force_pci_posting(dev); |
| mdelay(200); |
| |
| write_nic_word(dev, GP_ENABLE, 0xff & (~(1<<6))); /* bit 6 is for RF on/off detection */ |
| |
| |
| } |
| |
| void rtl8225_host_usb_init(struct net_device *dev) |
| { |
| write_nic_byte(dev,RFPinsSelect+1,0); |
| |
| write_nic_byte(dev,GPIO,0); |
| |
| write_nic_byte_E(dev,0x53,read_nic_byte_E(dev,0x53) | (1<<7)); |
| |
| write_nic_byte(dev,RFPinsSelect+1,4); |
| |
| write_nic_byte(dev,GPIO,0x20); |
| |
| write_nic_byte(dev,GP_ENABLE,0); |
| |
| |
| /* Config BB & RF */ |
| write_nic_word(dev, RFPinsOutput, 0x80); |
| |
| write_nic_word(dev, RFPinsSelect, 0x80); |
| |
| write_nic_word(dev, RFPinsEnable, 0x80); |
| |
| |
| mdelay(100); |
| |
| mdelay(1000); |
| |
| } |
| #endif |
| void rtl8225z2_rf_init(struct net_device *dev) |
| { |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| int i; |
| short channel = 1; |
| u16 brsr; |
| u32 data,addr; |
| |
| priv->chan = channel; |
| |
| // rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON); |
| |
| |
| if(priv->card_type == USB) |
| rtl8225_host_usb_init(dev); |
| else |
| rtl8225_host_pci_init(dev); |
| |
| write_nic_dword(dev, RF_TIMING, 0x000a8008); |
| |
| brsr = read_nic_word(dev, BRSR); |
| |
| write_nic_word(dev, BRSR, 0xffff); |
| |
| |
| write_nic_dword(dev, RF_PARA, 0x100044); |
| |
| #if 1 //0->1 |
| rtl8180_set_mode(dev, EPROM_CMD_CONFIG); |
| write_nic_byte(dev, CONFIG3, 0x44); |
| rtl8180_set_mode(dev, EPROM_CMD_NORMAL); |
| #endif |
| |
| |
| rtl8185_rf_pins_enable(dev); |
| |
| // mdelay(1000); |
| |
| write_rtl8225(dev, 0x0, 0x2bf); mdelay(1); |
| |
| |
| write_rtl8225(dev, 0x1, 0xee0); mdelay(1); |
| |
| write_rtl8225(dev, 0x2, 0x44d); mdelay(1); |
| |
| write_rtl8225(dev, 0x3, 0x441); mdelay(1); |
| |
| |
| write_rtl8225(dev, 0x4, 0x8c3);mdelay(1); |
| |
| |
| |
| write_rtl8225(dev, 0x5, 0xc72);mdelay(1); |
| // } |
| |
| write_rtl8225(dev, 0x6, 0xe6); mdelay(1); |
| |
| write_rtl8225(dev, 0x7, ((priv->card_type == USB)? 0x82a : rtl8225_chan[channel])); mdelay(1); |
| |
| write_rtl8225(dev, 0x8, 0x3f); mdelay(1); |
| |
| write_rtl8225(dev, 0x9, 0x335); mdelay(1); |
| |
| write_rtl8225(dev, 0xa, 0x9d4); mdelay(1); |
| |
| write_rtl8225(dev, 0xb, 0x7bb); mdelay(1); |
| |
| write_rtl8225(dev, 0xc, 0x850); mdelay(1); |
| |
| |
| write_rtl8225(dev, 0xd, 0xcdf); mdelay(1); |
| |
| write_rtl8225(dev, 0xe, 0x2b); mdelay(1); |
| |
| write_rtl8225(dev, 0xf, 0x114); |
| |
| |
| mdelay(100); |
| |
| |
| //if(priv->card_type != USB) /* maybe not needed even for 8185 */ |
| // write_rtl8225(dev, 0x7, rtl8225_chan[channel]); |
| |
| write_rtl8225(dev, 0x0, 0x1b7); |
| |
| for(i=0;i<95;i++){ |
| write_rtl8225(dev, 0x1, (u8)(i+1)); |
| |
| #if 0 |
| if(priv->phy_ver == 1) |
| /* version A */ |
| write_rtl8225(dev, 0x2, rtl8225a_rxgain[i]); |
| else |
| #endif |
| /* version B & C & D*/ |
| |
| write_rtl8225(dev, 0x2, rtl8225z2_rxgain[i]); |
| } |
| write_rtl8225(dev, 0x3, 0x80); |
| write_rtl8225(dev, 0x5, 0x4); |
| |
| write_rtl8225(dev, 0x0, 0xb7); |
| |
| write_rtl8225(dev, 0x2, 0xc4d); |
| |
| if(priv->card_type == USB){ |
| // force_pci_posting(dev); |
| mdelay(200); |
| |
| write_rtl8225(dev, 0x2, 0x44d); |
| |
| // force_pci_posting(dev); |
| mdelay(100); |
| |
| }//End of if(priv->card_type == USB) |
| /* FIXME!! rtl8187 we have to check if calibrarion |
| * is successful and eventually cal. again (repeat |
| * the two write on reg 2) |
| */ |
| // Check for calibration status, 2005.11.17, |
| data = read_rtl8225(dev, 6); |
| if (!(data&0x00000080)) |
| { |
| write_rtl8225(dev, 0x02, 0x0c4d); |
| force_pci_posting(dev); mdelay(200); |
| write_rtl8225(dev, 0x02, 0x044d); |
| force_pci_posting(dev); mdelay(100); |
| data = read_rtl8225(dev, 6); |
| if (!(data&0x00000080)) |
| { |
| DMESGW("RF Calibration Failed!!!!\n"); |
| } |
| } |
| //force_pci_posting(dev); |
| |
| mdelay(200); //200 for 8187 |
| |
| |
| // //if(priv->card_type != USB){ |
| // write_rtl8225(dev, 0x2, 0x44d); |
| // write_rtl8225(dev, 0x7, rtl8225_chan[channel]); |
| // write_rtl8225(dev, 0x2, 0x47d); |
| // |
| // force_pci_posting(dev); |
| // mdelay(100); |
| // |
| // write_rtl8225(dev, 0x2, 0x44d); |
| // //} |
| |
| write_rtl8225(dev, 0x0, 0x2bf); |
| |
| if(priv->card_type != USB) |
| rtl8185_rf_pins_enable(dev); |
| //set up ZEBRA AGC table, 2005.11.17, |
| for(i=0;i<128;i++){ |
| data = rtl8225_agc[i]; |
| |
| addr = i + 0x80; //enable writing AGC table |
| write_phy_ofdm(dev, 0xb, data); |
| |
| mdelay(1); |
| write_phy_ofdm(dev, 0xa, addr); |
| |
| mdelay(1); |
| } |
| #if 0 |
| for(i=0;i<128;i++){ |
| write_phy_ofdm(dev, 0xb, rtl8225_agc[i]); |
| |
| mdelay(1); |
| write_phy_ofdm(dev, 0xa, (u8)i+ 0x80); |
| |
| mdelay(1); |
| } |
| #endif |
| |
| force_pci_posting(dev); |
| mdelay(1); |
| |
| write_phy_ofdm(dev, 0x0, 0x1); mdelay(1); |
| write_phy_ofdm(dev, 0x1, 0x2); mdelay(1); |
| write_phy_ofdm(dev, 0x2, ((priv->card_type == USB)? 0x42 : 0x62)); mdelay(1); |
| write_phy_ofdm(dev, 0x3, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x4, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x5, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x6, 0x40); mdelay(1); |
| write_phy_ofdm(dev, 0x7, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x8, 0x40); mdelay(1); |
| write_phy_ofdm(dev, 0x9, 0xfe); mdelay(1); |
| |
| write_phy_ofdm(dev, 0xa, 0x8); mdelay(1); |
| |
| //write_phy_ofdm(dev, 0x18, 0xef); |
| // } |
| //} |
| write_phy_ofdm(dev, 0xb, 0x80); mdelay(1); |
| |
| write_phy_ofdm(dev, 0xc, 0x1);mdelay(1); |
| |
| |
| //if(priv->card_type != USB) |
| write_phy_ofdm(dev, 0xd, 0x43); |
| |
| write_phy_ofdm(dev, 0xe, 0xd3);mdelay(1); |
| |
| |
| #if 0 |
| if(priv->card_8185 == 1){ |
| if(priv->card_8185_Bversion) |
| write_phy_ofdm(dev, 0xf, 0x20);/*ver B*/ |
| else |
| write_phy_ofdm(dev, 0xf, 0x28);/*ver C*/ |
| }else{ |
| #endif |
| write_phy_ofdm(dev, 0xf, 0x38);mdelay(1); |
| /*ver D & 8187*/ |
| // } |
| |
| // if(priv->card_8185 == 1 && priv->card_8185_Bversion) |
| // write_phy_ofdm(dev, 0x10, 0x04);/*ver B*/ |
| // else |
| write_phy_ofdm(dev, 0x10, 0x84);mdelay(1); |
| /*ver C & D & 8187*/ |
| |
| write_phy_ofdm(dev, 0x11, 0x07);mdelay(1); |
| /*agc resp time 700*/ |
| |
| |
| // if(priv->card_8185 == 2){ |
| /* Ver D & 8187*/ |
| write_phy_ofdm(dev, 0x12, 0x20);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x13, 0x20);mdelay(1); |
| |
| #if 0 |
| }else{ |
| /* Ver B & C*/ |
| write_phy_ofdm(dev, 0x12, 0x0); |
| write_phy_ofdm(dev, 0x13, 0x0); |
| } |
| #endif |
| write_phy_ofdm(dev, 0x14, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x15, 0x40); mdelay(1); |
| write_phy_ofdm(dev, 0x16, 0x0); mdelay(1); |
| write_phy_ofdm(dev, 0x17, 0x40); mdelay(1); |
| |
| // if (priv->card_type == USB) |
| // write_phy_ofdm(dev, 0x18, 0xef); |
| |
| write_phy_ofdm(dev, 0x18, 0xef);mdelay(1); |
| |
| |
| write_phy_ofdm(dev, 0x19, 0x19); mdelay(1); |
| write_phy_ofdm(dev, 0x1a, 0x20); mdelay(1); |
| write_phy_ofdm(dev, 0x1b, 0x15);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x1c, 0x4);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x1d, 0xc5);mdelay(1); //2005.11.17, |
| |
| write_phy_ofdm(dev, 0x1e, 0x95);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x1f, 0x75); mdelay(1); |
| |
| // } |
| |
| write_phy_ofdm(dev, 0x20, 0x1f);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x21, 0x17);mdelay(1); |
| |
| write_phy_ofdm(dev, 0x22, 0x16);mdelay(1); |
| |
| // if(priv->card_type != USB) |
| write_phy_ofdm(dev, 0x23, 0x80);mdelay(1); //FIXME maybe not needed // <> |
| |
| write_phy_ofdm(dev, 0x24, 0x46); mdelay(1); |
| write_phy_ofdm(dev, 0x25, 0x00); mdelay(1); |
| write_phy_ofdm(dev, 0x26, 0x90); mdelay(1); |
| |
| write_phy_ofdm(dev, 0x27, 0x88); mdelay(1); |
| |
| |
| // <> Set init. gain to m74dBm. |
| |
| rtl8225z2_set_gain(dev,4); |
| |
| write_phy_cck(dev, 0x0, 0x98); mdelay(1); |
| write_phy_cck(dev, 0x3, 0x20); mdelay(1); |
| write_phy_cck(dev, 0x4, 0x7e); mdelay(1); |
| write_phy_cck(dev, 0x5, 0x12); mdelay(1); |
| write_phy_cck(dev, 0x6, 0xfc); mdelay(1); |
| |
| write_phy_cck(dev, 0x7, 0x78);mdelay(1); |
| /* Ver C & D & 8187*/ |
| |
| write_phy_cck(dev, 0x8, 0x2e);mdelay(1); |
| |
| write_phy_cck(dev, 0x10, ((priv->card_type == USB) ? 0x9b: 0x93)); mdelay(1); |
| write_phy_cck(dev, 0x11, 0x88); mdelay(1); |
| write_phy_cck(dev, 0x12, 0x47); mdelay(1); |
| #if 0 |
| if(priv->card_8185 == 1 && priv->card_8185_Bversion) |
| write_phy_cck(dev, 0x13, 0x98); /* Ver B */ |
| else |
| #endif |
| write_phy_cck(dev, 0x13, 0xd0); /* Ver C & D & 8187*/ |
| |
| write_phy_cck(dev, 0x19, 0x0); |
| write_phy_cck(dev, 0x1a, 0xa0); |
| write_phy_cck(dev, 0x1b, 0x8); |
| write_phy_cck(dev, 0x40, 0x86); /* CCK Carrier Sense Threshold */ |
| |
| write_phy_cck(dev, 0x41, 0x8d);mdelay(1); |
| |
| |
| write_phy_cck(dev, 0x42, 0x15); mdelay(1); |
| write_phy_cck(dev, 0x43, 0x18); mdelay(1); |
| |
| |
| write_phy_cck(dev, 0x44, 0x36); mdelay(1); |
| write_phy_cck(dev, 0x45, 0x35); mdelay(1); |
| write_phy_cck(dev, 0x46, 0x2e); mdelay(1); |
| write_phy_cck(dev, 0x47, 0x25); mdelay(1); |
| write_phy_cck(dev, 0x48, 0x1c); mdelay(1); |
| write_phy_cck(dev, 0x49, 0x12); mdelay(1); |
| write_phy_cck(dev, 0x4a, 0x9); mdelay(1); |
| write_phy_cck(dev, 0x4b, 0x4); mdelay(1); |
| write_phy_cck(dev, 0x4c, 0x5);mdelay(1); |
| |
| |
| write_nic_byte(dev, 0x5b, 0x0d); mdelay(1); |
| |
| |
| |
| // <> |
| // // TESTR 0xb 8187 |
| // write_phy_cck(dev, 0x10, 0x93);// & 0xfb); |
| // |
| // //if(priv->card_type != USB){ |
| // write_phy_ofdm(dev, 0x2, 0x62); |
| // write_phy_ofdm(dev, 0x6, 0x0); |
| // write_phy_ofdm(dev, 0x8, 0x0); |
| // //} |
| |
| rtl8225z2_SetTXPowerLevel(dev, channel); |
| #ifdef CONFIG_RTL818X_S |
| write_phy_cck(dev, 0x11, 0x9b); mdelay(1); /* Rx ant A, 0xdb for B */ |
| #else |
| write_phy_cck(dev, 0x10, 0x9b); mdelay(1); /* Rx ant A, 0xdb for B */ |
| #endif |
| write_phy_ofdm(dev, 0x26, 0x90); mdelay(1); /* Rx ant A, 0x10 for B */ |
| |
| rtl8185_tx_antenna(dev, 0x3); /* TX ant A, 0x0 for B */ |
| |
| /* switch to high-speed 3-wire |
| * last digit. 2 for both cck and ofdm |
| */ |
| if(priv->card_type == USB) |
| write_nic_dword(dev, 0x94, 0x3dc00002); |
| else{ |
| write_nic_dword(dev, 0x94, 0x15c00002); |
| rtl8185_rf_pins_enable(dev); |
| } |
| |
| // if(priv->card_type != USB) |
| // rtl8225_set_gain(dev, 4); /* FIXME this '1' is random */ // <> |
| // rtl8225_set_mode(dev, 1); /* FIXME start in B mode */ // <> |
| // |
| // /* make sure is waken up! */ |
| // write_rtl8225(dev,0x4, 0x9ff); |
| // rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON); |
| // rtl8185_set_anaparam2(dev, RTL8225_ANAPARAM2_ON); |
| |
| rtl8225_rf_set_chan(dev, priv->chan); |
| |
| //write_nic_word(dev,BRSR,brsr); |
| |
| //rtl8225z2_rf_set_mode(dev); |
| } |
| |
| void rtl8225z2_rf_set_mode(struct net_device *dev) |
| { |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| |
| if(priv->ieee80211->mode == IEEE_A) |
| { |
| write_rtl8225(dev, 0x5, 0x1865); |
| write_nic_dword(dev, RF_PARA, 0x10084); |
| write_nic_dword(dev, RF_TIMING, 0xa8008); |
| write_phy_ofdm(dev, 0x0, 0x0); |
| write_phy_ofdm(dev, 0xa, 0x6); |
| write_phy_ofdm(dev, 0xb, 0x99); |
| write_phy_ofdm(dev, 0xf, 0x20); |
| write_phy_ofdm(dev, 0x11, 0x7); |
| |
| rtl8225z2_set_gain(dev,4); |
| |
| write_phy_ofdm(dev,0x15, 0x40); |
| write_phy_ofdm(dev,0x17, 0x40); |
| |
| write_nic_dword(dev, 0x94,0x10000000); |
| }else{ |
| |
| write_rtl8225(dev, 0x5, 0x1864); |
| write_nic_dword(dev, RF_PARA, 0x10044); |
| write_nic_dword(dev, RF_TIMING, 0xa8008); |
| write_phy_ofdm(dev, 0x0, 0x1); |
| write_phy_ofdm(dev, 0xa, 0x6); |
| write_phy_ofdm(dev, 0xb, 0x99); |
| write_phy_ofdm(dev, 0xf, 0x20); |
| write_phy_ofdm(dev, 0x11, 0x7); |
| |
| rtl8225z2_set_gain(dev,4); |
| |
| write_phy_ofdm(dev,0x15, 0x40); |
| write_phy_ofdm(dev,0x17, 0x40); |
| |
| write_nic_dword(dev, 0x94,0x04000002); |
| } |
| } |
| |
| //lzm mod 080826 |
| //#define MAX_DOZE_WAITING_TIMES_85B 64 |
| //#define MAX_POLLING_24F_TIMES_87SE 5 |
| #define MAX_DOZE_WAITING_TIMES_85B 20 |
| #define MAX_POLLING_24F_TIMES_87SE 10 |
| #define LPS_MAX_SLEEP_WAITING_TIMES_87SE 5 |
| |
| bool |
| SetZebraRFPowerState8185( |
| struct net_device *dev, |
| RT_RF_POWER_STATE eRFPowerState |
| ) |
| { |
| struct r8180_priv *priv = ieee80211_priv(dev); |
| u8 btCR9346, btConfig3; |
| bool bActionAllowed= true, bTurnOffBB = true;//lzm mod 080826 |
| //u32 DWordContent; |
| u8 u1bTmp; |
| int i; |
| //u16 u2bTFPC = 0; |
| bool bResult = true; |
| u8 QueueID; |
| |
| if(priv->SetRFPowerStateInProgress == true) |
| return false; |
| |
| priv->SetRFPowerStateInProgress = true; |
| |
| // enable EEM0 and EEM1 in 9346CR |
| btCR9346 = read_nic_byte(dev, CR9346); |
| write_nic_byte(dev, CR9346, (btCR9346|0xC0) ); |
| // enable PARM_En in Config3 |
| btConfig3 = read_nic_byte(dev, CONFIG3); |
| write_nic_byte(dev, CONFIG3, (btConfig3|CONFIG3_PARM_En) ); |
| |
| switch( priv->rf_chip ) |
| { |
| case RF_ZEBRA2: |
| switch( eRFPowerState ) |
| { |
| case eRfOn: |
| RF_WriteReg(dev,0x4,0x9FF); |
| |
| write_nic_dword(dev, ANAPARAM, ANAPARM_ON); |
| write_nic_dword(dev, ANAPARAM2, ANAPARM2_ON); |
| |
| write_nic_byte(dev, CONFIG4, priv->RFProgType); |
| |
| //Follow 87B, Isaiah 2007-04-27 |
| u1bTmp = read_nic_byte(dev, 0x24E); |
| write_nic_byte(dev, 0x24E, (u1bTmp & (~(BIT5|BIT6))) );// 070124 SD1 Alex: turn on CCK and OFDM. |
| break; |
| |
| case eRfSleep: |
| break; |
| |
| case eRfOff: |
| break; |
| |
| default: |
| bResult = false; |
| break; |
| } |
| break; |
| |
| case RF_ZEBRA4: |
| switch( eRFPowerState ) |
| { |
| case eRfOn: |
| //printk("===================================power on@jiffies:%d\n",jiffies); |
| write_nic_word(dev, 0x37C, 0x00EC); |
| |
| //turn on AFE |
| write_nic_byte(dev, 0x54, 0x00); |
| write_nic_byte(dev, 0x62, 0x00); |
| |
| //lzm mod 080826 |
| //turn on RF |
| //RF_WriteReg(dev, 0x0, 0x009f); //mdelay(1); |
| //RF_WriteReg(dev, 0x4, 0x0972); //mdelay(1); |
| RF_WriteReg(dev, 0x0, 0x009f); udelay(500); |
| RF_WriteReg(dev, 0x4, 0x0972); udelay(500); |
| //turn on RF again, suggested by SD3 stevenl. |
| RF_WriteReg(dev, 0x0, 0x009f); udelay(500); |
| RF_WriteReg(dev, 0x4, 0x0972); udelay(500); |
| |
| //turn on BB |
| // write_nic_dword(dev, PhyAddr, 0x4090); //ofdm 10=00 |
| // write_nic_dword(dev, PhyAddr, 0x4092); //ofdm 12=00 |
| write_phy_ofdm(dev,0x10,0x40); |
| write_phy_ofdm(dev,0x12,0x40); |
| //Avoid power down at init time. |
| write_nic_byte(dev, CONFIG4, priv->RFProgType); |
| |
| u1bTmp = read_nic_byte(dev, 0x24E); |
| write_nic_byte(dev, 0x24E, (u1bTmp & (~(BIT5|BIT6))) ); |
| |
| break; |
| |
| case eRfSleep: |
| // Make sure BusyQueue is empty befor turn off RFE pwoer. |
| //printk("===================================power sleep@jiffies:%d\n",jiffies); |
| |
| for(QueueID = 0, i = 0; QueueID < 6; ) |
| { |
| if(get_curr_tx_free_desc(dev,QueueID) == priv->txringcount) |
| { |
| QueueID++; |
| continue; |
| } |
| #if 0 //reserved amy |
| else if(priv->NdisAdapter.CurrentPowerState != NdisDeviceStateD0) |
| { |
| RT_TRACE(COMP_POWER, DBG_LOUD, ("eRfSleep: %d times TcbBusyQueue[%d] !=0 but lower power state!\n", (pMgntInfo->TxPollingTimes+1), QueueID)); |
| break; |
| } |
| #endif |
| else//lzm mod 080826 |
| { |
| priv->TxPollingTimes ++; |
| if(priv->TxPollingTimes >= LPS_MAX_SLEEP_WAITING_TIMES_87SE) |
| { |
| //RT_TRACE(COMP_POWER, DBG_WARNING, ("\n\n\n SetZebraRFPowerState8185B():eRfSleep: %d times TcbBusyQueue[%d] != 0 !!!\n\n\n", LPS_MAX_SLEEP_WAITING_TIMES_87SE, QueueID)); |
| bActionAllowed=false; |
| break; |
| } |
| else |
| { |
| udelay(10); // Windows may delay 3~16ms actually. |
| //RT_TRACE(COMP_POWER, DBG_LOUD, ("eRfSleep: %d times TcbBusyQueue[%d] !=0 before doze!\n", (pMgntInfo->TxPollingTimes), QueueID)); |
| } |
| } |
| |
| //lzm del 080826 |
| //if(i >= MAX_DOZE_WAITING_TIMES_85B) |
| //{ |
| //printk("\n\n\n SetZebraRFPowerState8185B(): %d times BusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_85B, QueueID); |
| //break; |
| //} |
| } |
| |
| if(bActionAllowed)//lzm add 080826 |
| { |
| //turn off BB RXIQ matrix to cut off rx signal |
| // write_nic_dword(dev, PhyAddr, 0x0090); //ofdm 10=00 |
| // write_nic_dword(dev, PhyAddr, 0x0092); //ofdm 12=00 |
| write_phy_ofdm(dev,0x10,0x00); |
| write_phy_ofdm(dev,0x12,0x00); |
| //turn off RF |
| RF_WriteReg(dev, 0x4, 0x0000); //mdelay(1); |
| RF_WriteReg(dev, 0x0, 0x0000); //mdelay(1); |
| //turn off AFE except PLL |
| write_nic_byte(dev, 0x62, 0xff); |
| write_nic_byte(dev, 0x54, 0xec); |
| // mdelay(10); |
| |
| #if 1 |
| mdelay(1); |
| { |
| int i = 0; |
| while (true) |
| { |
| u8 tmp24F = read_nic_byte(dev, 0x24f); |
| if ((tmp24F == 0x01) || (tmp24F == 0x09)) |
| { |
| bTurnOffBB = true; |
| break; |
| } |
| else//lzm mod 080826 |
| { |
| udelay(10); |
| i++; |
| priv->TxPollingTimes++; |
| |
| if(priv->TxPollingTimes >= LPS_MAX_SLEEP_WAITING_TIMES_87SE) |
| { |
| //RT_TRACE(COMP_POWER, DBG_WARNING, ("\n\n\n SetZebraRFPowerState8185B(): eRfOff: %d times Rx Mac0x24F=0x%x !!!\n\n\n", i, u1bTmp24F)); |
| bTurnOffBB=false; |
| break; |
| } |
| else |
| { |
| udelay(10);// Windows may delay 3~16ms actually. |
| //RT_TRACE(COMP_POWER, DBG_LOUD,("(%d)eRfSleep- u1bTmp24F= 0x%X\n", i, u1bTmp24F)); |
| |
| } |
| } |
| |
| //lzm del 080826 |
| //if (i > MAX_POLLING_24F_TIMES_87SE) |
| // break; |
| } |
| } |
| #endif |
| if (bTurnOffBB)//lzm mod 080826 |
| { |
| //turn off BB |
| u1bTmp = read_nic_byte(dev, 0x24E); |
| write_nic_byte(dev, 0x24E, (u1bTmp|BIT5|BIT6)); |
| |
| //turn off AFE PLL |
| //write_nic_byte(dev, 0x54, 0xec); |
| //write_nic_word(dev, 0x37C, 0x00ec); |
| write_nic_byte(dev, 0x54, 0xFC); //[ECS] FC-> EC->FC, asked by SD3 Stevenl |
| write_nic_word(dev, 0x37C, 0x00FC);//[ECS] FC-> EC->FC, asked by SD3 Stevenl |
| } |
| } |
| break; |
| |
| case eRfOff: |
| // Make sure BusyQueue is empty befor turn off RFE pwoer. |
| //printk("===================================power off@jiffies:%d\n",jiffies); |
| for(QueueID = 0, i = 0; QueueID < 6; ) |
| { |
| if(get_curr_tx_free_desc(dev,QueueID) == priv->txringcount) |
| { |
| QueueID++; |
| continue; |
| } |
| #if 0 |
| else if(Adapter->NdisAdapter.CurrentPowerState != NdisDeviceStateD0) |
| { |
| RT_TRACE(COMP_POWER, DBG_LOUD, ("%d times TcbBusyQueue[%d] !=0 but lower power state!\n", (i+1), QueueID)); |
| break; |
| } |
| #endif |
| else |
| { |
| udelay(10); |
| i++; |
| } |
| |
| if(i >= MAX_DOZE_WAITING_TIMES_85B) |
| { |
| //printk("\n\n\n SetZebraRFPowerState8185B(): %d times BusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_85B, QueueID); |
| break; |
| } |
| } |
| |
| //turn off BB RXIQ matrix to cut off rx signal |
| // write_nic_dword(dev, PhyAddr, 0x0090); //ofdm 10=00 |
| // write_nic_dword(dev, PhyAddr, 0x0092); //ofdm 12=00 |
| write_phy_ofdm(dev,0x10,0x00); |
| write_phy_ofdm(dev,0x12,0x00); |
| //turn off RF |
| RF_WriteReg(dev, 0x4, 0x0000); //mdelay(1); |
| RF_WriteReg(dev, 0x0, 0x0000); //mdelay(1); |
| //turn off AFE except PLL |
| write_nic_byte(dev, 0x62, 0xff); |
| write_nic_byte(dev, 0x54, 0xec); |
| // mdelay(10); |
| #if 1 |
| mdelay(1); |
| { |
| int i = 0; |
| while (true) |
| { |
| u8 tmp24F = read_nic_byte(dev, 0x24f); |
| if ((tmp24F == 0x01) || (tmp24F == 0x09)) |
| { |
| bTurnOffBB = true; |
| break; |
| } |
| else |
| { |
| bTurnOffBB = false; |
| udelay(10); |
| i++; |
| } |
| if (i > MAX_POLLING_24F_TIMES_87SE) |
| break; |
| } |
| } |
| #endif |
| if (bTurnOffBB)//lzm mod 080826 |
| { |
| |
| //turn off BB |
| u1bTmp = read_nic_byte(dev, 0x24E); |
| write_nic_byte(dev, 0x24E, (u1bTmp|BIT5|BIT6)); |
| //turn off AFE PLL (80M) |
| //write_nic_byte(dev, 0x54, 0xec); |
| //write_nic_word(dev, 0x37C, 0x00ec); |
| write_nic_byte(dev, 0x54, 0xFC); //[ECS] FC-> EC->FC, asked by SD3 Stevenl |
| write_nic_word(dev, 0x37C, 0x00FC); //[ECS] FC-> EC->FC, asked by SD3 Stevenl |
| } |
| |
| break; |
| |
| default: |
| bResult = false; |
| printk("SetZebraRFPowerState8185(): unknow state to set: 0x%X!!!\n", eRFPowerState); |
| break; |
| } |
| break; |
| } |
| |
| // disable PARM_En in Config3 |
| btConfig3 &= ~(CONFIG3_PARM_En); |
| write_nic_byte(dev, CONFIG3, btConfig3); |
| // disable EEM0 and EEM1 in 9346CR |
| btCR9346 &= ~(0xC0); |
| write_nic_byte(dev, CR9346, btCR9346); |
| |
| if(bResult && bActionAllowed)//lzm mod 080826 |
| { |
| // Update current RF state variable. |
| priv->eRFPowerState = eRFPowerState; |
| #if 0 |
| switch(priv->eRFPowerState) |
| { |
| case eRfOff: |
| // |
| //If Rf off reason is from IPS, Led should blink with no link, by Maddest 071015 |
| // |
| if(priv->RfOffReason==RF_CHANGE_BY_IPS ) |
| { |
| Adapter->HalFunc.LedControlHandler(Adapter,LED_CTL_NO_LINK); |
| } |
| else |
| { |
| // Turn off LED if RF is not ON. |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_POWER_OFF); |
| } |
| break; |
| |
| case eRfOn: |
| // Turn on RF we are still linked, which might happen when |
| // we quickly turn off and on HW RF. 2006.05.12, by rcnjko. |
| if( pMgntInfo->bMediaConnect == TRUE ) |
| { |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_LINK); |
| } |
| break; |
| |
| default: |
| // do nothing. |
| break; |
| } |
| #endif |
| |
| } |
| |
| priv->SetRFPowerStateInProgress = false; |
| |
| return (bResult && bActionAllowed) ; |
| } |
| void rtl8225z4_rf_sleep(struct net_device *dev) |
| { |
| // |
| // Turn off RF power. |
| // |
| //printk("=========>%s()\n", __FUNCTION__); |
| MgntActSet_RF_State(dev, eRfSleep, RF_CHANGE_BY_PS); |
| //mdelay(2); //FIXME |
| } |
| void rtl8225z4_rf_wakeup(struct net_device *dev) |
| { |
| // |
| // Turn on RF power. |
| // |
| //printk("=========>%s()\n", __FUNCTION__); |
| MgntActSet_RF_State(dev, eRfOn, RF_CHANGE_BY_PS); |
| } |
| #endif |
| |