Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Seems like we've had more fixes than usual this release cycle, but
there's nothing in particular that we're doing differently. Perhaps
it's just one of those cycles where more people are finding more
regressions (and/or that the latency of when people actually test
what's been in the tree for a while is catching up so that we get the
bug reports now).
The bigger changes here are are for TI and Marvell platforms:
* Timing changes for GPMC (generic localbus) on OMAP causing some
largeish DTS deltas.
* Fixes to window allocation on PCI for mvebu touching drivers/
stuff. Patches have acks from subsystem maintainers where needed.
* A fix from Thomas for a botched DT conversion in drivers/edma.
There's a handful of other fixes for the above platforms as well as
sunxi, at91, i.MX. I also included a MAINTAINER update for Broadcom,
and a trivial move of a binding doc.
I know you said you'd be offline this week, but I might as well post
it for when you return. :)"
I'm not quite offline yet. Doing a few pulls in the last hour before my
internet goes away..
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
MAINTAINERS: update Broadcom ARM tree location and add an SoC family
ARM: dts: i.MX53: Fix ipu register space size
ARM: dts: kirkwood: fix mislocated pcie-controller nodes
ARM: sunxi: Enable GMAC in sunxi_defconfig
ARM: common: edma: Fix xbar mapping
ARM: sun7i: Fix i2c4 base address
ARM: Kirkwood: T5325: Fix double probe of Codec
ARM: mvebu: enable the SATA interface on Armada 375 DB
ARM: mvebu: specify I2C bus frequency on Armada 370 DB
ARM: mvebu: use qsgmii phy-mode for Armada XP GP interfaces
ARM: mvebu: fix NOR bus-width in Armada XP OpenBlocks AX3 Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP DB Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP GP Device Tree
ARM: dts: AM3517: Disable absent IPs inherited from OMAP3
ARM: dts: OMAP2: Fix interrupts for OMAP2420 mailbox
ARM: dts: OMAP5: Add mailbox dt node to fix boot warning
ARM: OMAP5: Switch to THUMB mode if needed on secondary CPU
ARM: dts: am437x-gp-evm: Do not reset gpio5
ARM: dts: omap3-igep0020: use SMSC9221 timings
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
...
diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
index cd5e239..6794cdc 100644
--- a/Documentation/devicetree/bindings/clock/at91-clock.txt
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -62,7 +62,7 @@
- interrupt-controller : tell that the PMC is an interrupt controller.
- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
and reflect the bit position in the PMC_ER/DR/SR registers.
- You can use the dt macros defined in dt-bindings/clk/at91.h.
+ You can use the dt macros defined in dt-bindings/clock/at91.h.
0 (AT91_PMC_MOSCS) -> main oscillator ready
1 (AT91_PMC_LOCKA) -> PLL A ready
2 (AT91_PMC_LOCKB) -> PLL B ready
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt
index 9fbbdb7..68ff213 100644
--- a/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -29,6 +29,6 @@
dma-channels = <64>;
ti,edma-regions = <4>;
ti,edma-slots = <256>;
- ti,edma-xbar-event-map = <1 12
- 2 13>;
+ ti,edma-xbar-event-map = /bits/ 16 <1 12
+ 2 13>;
};
diff --git a/MAINTAINERS b/MAINTAINERS
index 764075d..c596b74 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1893,14 +1893,15 @@
S: Supported
F: drivers/net/ethernet/broadcom/bnx2x/
-BROADCOM BCM281XX/BCM11XXX ARM ARCHITECTURE
+BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
M: Christian Daudt <bcm@fixthebug.org>
M: Matt Porter <mporter@linaro.org>
L: bcm-kernel-feedback-list@broadcom.com
-T: git git://git.github.com/broadcom/bcm11351
+T: git git://github.com/broadcom/mach-bcm
S: Maintained
F: arch/arm/mach-bcm/
F: arch/arm/boot/dts/bcm113*
+F: arch/arm/boot/dts/bcm216*
F: arch/arm/boot/dts/bcm281*
F: arch/arm/configs/bcm_defconfig
F: drivers/mmc/host/sdhci_bcm_kona.c
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index cb6811e..7ad75b4 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -144,7 +144,7 @@
compatible = "ti,edma3";
ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
reg = <0x49000000 0x10000>,
- <0x44e10f90 0x10>;
+ <0x44e10f90 0x40>;
interrupts = <12 13 14>;
#dma-cells = <1>;
dma-channels = <64>;
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index 788391f..5a452fd 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -62,5 +62,21 @@
};
};
+&iva {
+ status = "disabled";
+};
+
+&mailbox {
+ status = "disabled";
+};
+
+&mmu_isp {
+ status = "disabled";
+};
+
+&smartreflex_mpu_iva {
+ status = "disabled";
+};
+
/include/ "am35xx-clocks.dtsi"
/include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index df8798e..a055f7f 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -117,6 +117,11 @@
status = "okay";
};
+&gpio5 {
+ status = "okay";
+ ti,no-reset-on-init;
+};
+
&mmc1 {
status = "okay";
vmmc-supply = <&vmmcsd_fixed>;
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 82f238a..3383c4b 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -67,6 +67,7 @@
i2c@11000 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
+ clock-frequency = <100000>;
status = "okay";
audio_codec: audio-codec@4a {
compatible = "cirrus,cs42l51";
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 9378d31..0451124 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -79,6 +79,11 @@
};
};
+ sata@a0000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
nand: nand@d0000 {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index 448373c..90f0bf6 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -49,7 +49,7 @@
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 61bda68..0c75642 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -59,7 +59,7 @@
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
@@ -146,22 +146,22 @@
ethernet@70000 {
status = "okay";
phy = <&phy0>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
- phy-mode = "rgmii-id";
+ phy-mode = "qsgmii";
};
/* Front-side USB slot */
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 985948c..5d42feb 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -39,7 +39,7 @@
/* Device Bus parameters are required */
/* Read parameters */
- devbus,bus-width = <8>;
+ devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index ce13755..4537259 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -34,7 +34,7 @@
};
spi0: spi@f0004000 {
- cs-gpios = <&pioD 13 0>;
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
status = "okay";
};
@@ -79,7 +79,7 @@
};
spi1: spi@f8008000 {
- cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+ cs-gpios = <&pioC 25 0>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index e21dda0..3be973e 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -10,7 +10,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
model = "Atmel AT91SAM9261 family SoC";
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 63e1784..92a52fa 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -8,7 +8,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9c2bff2..6a1bf4f 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -115,7 +115,7 @@
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx53-ipu";
- reg = <0x18000000 0x080000000>;
+ reg = <0x18000000 0x08000000>;
interrupts = <11 10>;
clocks = <&clks IMX5_CLK_IPU_GATE>,
<&clks IMX5_CLK_IPU_DI0_GATE>,
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
index 32c6fb4..b939f4f5 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -30,6 +30,16 @@
bootargs = "console=ttyS0,115200n8 earlyprintk";
};
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
ocp@f1000000 {
pinctrl@10000 {
pmx_usb_led: pmx-usb-led {
@@ -73,14 +83,6 @@
ehci@50000 {
status = "okay";
};
-
- pcie-controller {
- status = "okay";
-
- pcie@1,0 {
- status = "okay";
- };
- };
};
gpio-leds {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
index aa78c2d..e2cc85c 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
@@ -4,6 +4,16 @@
/ {
model = "ZyXEL NSA310";
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
ocp@f1000000 {
pinctrl: pinctrl@10000 {
@@ -26,14 +36,6 @@
status = "okay";
nr-ports = <2>;
};
-
- pcie-controller {
- status = "okay";
-
- pcie@1,0 {
- status = "okay";
- };
- };
};
gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
index 7d1c767..0bd70d9 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -127,11 +127,6 @@
i2c@11000 {
status = "okay";
-
- alc5621: alc5621@1a {
- compatible = "realtek,alc5621";
- reg = <0x1a>;
- };
};
serial@12000 {
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
index f577b7d..521c587 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -24,11 +24,10 @@
compatible = "smsc,lan9221", "smsc,lan9115";
bank-width = <2>;
gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
+ gpmc,cs-on-ns = <1>;
+ gpmc,cs-rd-off-ns = <180>;
+ gpmc,cs-wr-off-ns = <180>;
+ gpmc,adv-rd-off-ns = <18>;
gpmc,adv-wr-off-ns = <48>;
gpmc,oe-on-ns = <54>;
gpmc,oe-off-ns = <168>;
@@ -36,12 +35,10 @@
gpmc,we-off-ns = <168>;
gpmc,rd-cycle-ns = <186>;
gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
+ gpmc,access-ns = <144>;
+ gpmc,page-burst-access-ns = <24>;
+ gpmc,bus-turnaround-ns = <90>;
+ gpmc,cycle2cycle-delay-ns = <90>;
gpmc,cycle2cycle-samecsen;
gpmc,cycle2cycle-diffcsen;
vddvario-supply = <&vddvario>;
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 22f35ea..8f8c07d 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -71,13 +71,6 @@
interrupts = <58>;
};
- mailbox: mailbox@48094000 {
- compatible = "ti,omap2-mailbox";
- ti,hwmods = "mailbox";
- reg = <0x48094000 0x200>;
- interrupts = <26>;
- };
-
intc: interrupt-controller@1 {
compatible = "ti,omap2-intc";
interrupt-controller;
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi
index 85b1fb0..2d99798 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/omap2420.dtsi
@@ -125,6 +125,14 @@
dma-names = "tx", "rx";
};
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>, <34>;
+ interrupt-names = "dsp", "iva";
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@48028000 {
compatible = "ti,omap2420-timer";
reg = <0x48028000 0x400>;
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi
index d09697d..42d2c61 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/omap2430.dtsi
@@ -216,6 +216,13 @@
dma-names = "tx", "rx";
};
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>;
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@49018000 {
compatible = "ti,omap2420-timer";
reg = <0x49018000 0x400>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
index d000558..25ba083 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -10,18 +10,6 @@
cpu0-supply = <&vcc>;
};
};
-
- vddvario: regulator-vddvario {
- compatible = "regulator-fixed";
- regulator-name = "vddvario";
- regulator-always-on;
- };
-
- vdd33a: regulator-vdd33a {
- compatible = "regulator-fixed";
- regulator-name = "vdd33a";
- regulator-always-on;
- };
};
&omap3_pmx_core {
@@ -35,58 +23,34 @@
hsusb0_pins: pinmux_hsusb0_pins {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
- OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
- OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
- OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
- OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
- OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
- OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
- OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
- OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
- OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
- OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
- OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
>;
};
};
+#include "omap-gpmc-smsc911x.dtsi"
+
&gpmc {
ranges = <5 0 0x2c000000 0x01000000>;
- smsc1: ethernet@5,0 {
+ smsc1: ethernet@gpmc {
compatible = "smsc,lan9221", "smsc,lan9115";
pinctrl-names = "default";
pinctrl-0 = <&smsc1_pins>;
interrupt-parent = <&gpio6>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
reg = <5 0 0xff>;
- bank-width = <2>;
- gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
- gpmc,adv-wr-off-ns = <48>;
- gpmc,oe-on-ns = <54>;
- gpmc,oe-off-ns = <168>;
- gpmc,we-on-ns = <54>;
- gpmc,we-off-ns = <168>;
- gpmc,rd-cycle-ns = <186>;
- gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
- gpmc,cycle2cycle-samecsen;
- gpmc,cycle2cycle-diffcsen;
- vddvario-supply = <&vddvario>;
- vdd33a-supply = <&vdd33a>;
- reg-io-width = <4>;
- smsc,save-mac-address;
};
};
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index b97736d..e2d163b 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -107,7 +107,7 @@
>;
};
- smsc911x_pins: pinmux_smsc911x_pins {
+ smsc9221_pins: pinmux_smsc9221_pins {
pinctrl-single,pins = <
0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
>;
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 7abd64f..b22caaa 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -10,7 +10,7 @@
*/
#include "omap3-igep.dtsi"
-#include "omap-gpmc-smsc911x.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
/ {
model = "IGEPv2 (TI OMAP AM/DM37x)";
@@ -248,7 +248,7 @@
ethernet@gpmc {
pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
+ pinctrl-0 = <&smsc9221_pins>;
reg = <5 0 0xff>;
interrupt-parent = <&gpio6>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
index 7909c51..d59e3de 100644
--- a/arch/arm/boot/dts/omap3-sb-t35.dtsi
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -2,20 +2,6 @@
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
*/
-/ {
- vddvario_sb_t35: regulator-vddvario-sb-t35 {
- compatible = "regulator-fixed";
- regulator-name = "vddvario";
- regulator-always-on;
- };
-
- vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
- compatible = "regulator-fixed";
- regulator-name = "vdd33a";
- regulator-always-on;
- };
-};
-
&omap3_pmx_core {
smsc2_pins: pinmux_smsc2_pins {
pinctrl-single,pins = <
@@ -37,11 +23,10 @@
reg = <4 0 0xff>;
bank-width = <2>;
gpmc,mux-add-data;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <186>;
- gpmc,cs-wr-off-ns = <186>;
- gpmc,adv-on-ns = <12>;
- gpmc,adv-rd-off-ns = <48>;
+ gpmc,cs-on-ns = <1>;
+ gpmc,cs-rd-off-ns = <180>;
+ gpmc,cs-wr-off-ns = <180>;
+ gpmc,adv-rd-off-ns = <18>;
gpmc,adv-wr-off-ns = <48>;
gpmc,oe-on-ns = <54>;
gpmc,oe-off-ns = <168>;
@@ -49,16 +34,14 @@
gpmc,we-off-ns = <168>;
gpmc,rd-cycle-ns = <186>;
gpmc,wr-cycle-ns = <186>;
- gpmc,access-ns = <114>;
- gpmc,page-burst-access-ns = <6>;
- gpmc,bus-turnaround-ns = <12>;
- gpmc,cycle2cycle-delay-ns = <18>;
- gpmc,wr-data-mux-bus-ns = <90>;
- gpmc,wr-access-ns = <186>;
+ gpmc,access-ns = <144>;
+ gpmc,page-burst-access-ns = <24>;
+ gpmc,bus-turnaround-ns = <90>;
+ gpmc,cycle2cycle-delay-ns = <90>;
gpmc,cycle2cycle-samecsen;
gpmc,cycle2cycle-diffcsen;
- vddvario-supply = <&vddvario_sb_t35>;
- vdd33a-supply = <&vdd33a_sb_t35>;
+ vddvario-supply = <&vddvario>;
+ vdd33a-supply = <&vdd33a>;
reg-io-width = <4>;
smsc,save-mac-address;
};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts
index 024c9c6..42189b6 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3517.dts
+++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts
@@ -8,6 +8,19 @@
/ {
model = "CompuLab SBC-T3517 with CM-T3517";
compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+ /* Only one GPMC smsc9220 on SBC-T3517, CM-T3517 uses am35x Ethernet */
+ vddvario: regulator-vddvario-sb-t35 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddvario";
+ regulator-always-on;
+ };
+
+ vdd33a: regulator-vdd33a-sb-t35 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33a";
+ regulator-always-on;
+ };
};
&omap3_pmx_core {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index acb9019..4231191 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -61,7 +61,7 @@
ti,hwmods = "mpu";
};
- iva {
+ iva: iva {
compatible = "ti,iva2.2";
ti,hwmods = "iva";
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index f8c9855..36b4312 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -630,6 +630,13 @@
status = "disabled";
};
+ mailbox: mailbox@4a0f4000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x4a0f4000 0x200>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ };
+
timer1: timer@4ae18000 {
compatible = "ti,omap5430-timer";
reg = <0x4ae18000 0x80>;
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index eabcfdb..a106b08 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -13,7 +13,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
model = "Atmel SAMA5D3 family SoC";
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi
index b029fe7..1b02208 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
ahb {
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 382b044..0284845 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
aliases {
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a9fa75e..7a8d4c6 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
/ {
aliases {
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 32efc10..aba1c8a 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -87,7 +87,7 @@
pll4: clk@01c20018 {
#clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
+ compatible = "allwinner,sun7i-a20-pll4-clk";
reg = <0x01c20018 0x4>;
clocks = <&osc24M>;
clock-output-names = "pll4";
@@ -109,6 +109,14 @@
clock-output-names = "pll6_sata", "pll6_other", "pll6";
};
+ pll8: clk@01c20040 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun7i-a20-pll4-clk";
+ reg = <0x01c20040 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll8";
+ };
+
cpu: cpu@01c20054 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-cpu-clk";
@@ -805,9 +813,9 @@
status = "disabled";
};
- i2c4: i2c@01c2bc00 {
+ i2c4: i2c@01c2c000 {
compatible = "allwinner,sun4i-i2c";
- reg = <0x01c2bc00 0x400>;
+ reg = <0x01c2c000 0x400>;
interrupts = <0 89 4>;
clocks = <&apb1_gates 15>;
clock-frequency = <100000>;
diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
index 41bca32..5339009 100644
--- a/arch/arm/common/edma.c
+++ b/arch/arm/common/edma.c
@@ -1423,55 +1423,38 @@
#if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_DMADEVICES)
-static int edma_of_read_u32_to_s16_array(const struct device_node *np,
- const char *propname, s16 *out_values,
- size_t sz)
+static int edma_xbar_event_map(struct device *dev, struct device_node *node,
+ struct edma_soc_info *pdata, size_t sz)
{
- int ret;
-
- ret = of_property_read_u16_array(np, propname, out_values, sz);
- if (ret)
- return ret;
-
- /* Terminate it */
- *out_values++ = -1;
- *out_values++ = -1;
-
- return 0;
-}
-
-static int edma_xbar_event_map(struct device *dev,
- struct device_node *node,
- struct edma_soc_info *pdata, int len)
-{
- int ret, i;
+ const char pname[] = "ti,edma-xbar-event-map";
struct resource res;
void __iomem *xbar;
- const s16 (*xbar_chans)[2];
+ s16 (*xbar_chans)[2];
+ size_t nelm = sz / sizeof(s16);
u32 shift, offset, mux;
+ int ret, i;
- xbar_chans = devm_kzalloc(dev,
- len/sizeof(s16) + 2*sizeof(s16),
- GFP_KERNEL);
+ xbar_chans = devm_kzalloc(dev, (nelm + 2) * sizeof(s16), GFP_KERNEL);
if (!xbar_chans)
return -ENOMEM;
ret = of_address_to_resource(node, 1, &res);
if (ret)
- return -EIO;
+ return -ENOMEM;
xbar = devm_ioremap(dev, res.start, resource_size(&res));
if (!xbar)
return -ENOMEM;
- ret = edma_of_read_u32_to_s16_array(node,
- "ti,edma-xbar-event-map",
- (s16 *)xbar_chans,
- len/sizeof(u32));
+ ret = of_property_read_u16_array(node, pname, (u16 *)xbar_chans, nelm);
if (ret)
return -EIO;
- for (i = 0; xbar_chans[i][0] != -1; i++) {
+ /* Invalidate last entry for the other user of this mess */
+ nelm >>= 1;
+ xbar_chans[nelm][0] = xbar_chans[nelm][1] = -1;
+
+ for (i = 0; i < nelm; i++) {
shift = (xbar_chans[i][1] & 0x03) << 3;
offset = xbar_chans[i][1] & 0xfffffffc;
mux = readl(xbar + offset);
@@ -1480,8 +1463,7 @@
writel(mux, (xbar + offset));
}
- pdata->xbar_chans = xbar_chans;
-
+ pdata->xbar_chans = (const s16 (*)[2]) xbar_chans;
return 0;
}
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index b5df4a5..81ba78e 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -37,7 +37,7 @@
# CONFIG_NET_VENDOR_NATSEMI is not set
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_STMMAC_ETH=y
# CONFIG_NET_VENDOR_WIZNET is not set
# CONFIG_WLAN is not set
CONFIG_SERIAL_8250=y
diff --git a/arch/arm/mach-omap2/omap-headsmp.S b/arch/arm/mach-omap2/omap-headsmp.S
index 75e9295..40c5d5f 100644
--- a/arch/arm/mach-omap2/omap-headsmp.S
+++ b/arch/arm/mach-omap2/omap-headsmp.S
@@ -1,7 +1,7 @@
/*
* Secondary CPU startup routine source file.
*
- * Copyright (C) 2009 Texas Instruments, Inc.
+ * Copyright (C) 2009-2014 Texas Instruments, Inc.
*
* Author:
* Santosh Shilimkar <santosh.shilimkar@ti.com>
@@ -28,9 +28,13 @@
* code. This routine also provides a holding flag into which
* secondary core is held until we're ready for it to initialise.
* The primary core will update this flag using a hardware
-+ * register AuxCoreBoot0.
+ * register AuxCoreBoot0.
*/
ENTRY(omap5_secondary_startup)
+.arm
+THUMB( adr r9, BSYM(wait) ) @ CPU may be entered in ARM mode.
+THUMB( bx r9 ) @ If this is a Thumb-2 kernel,
+THUMB( .thumb ) @ switch to Thumb now.
wait: ldr r2, =AUX_CORE_BOOT0_PA @ read from AuxCoreBoot0
ldr r0, [r2]
mov r0, r0, lsr #5
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index f565f99..7548db2 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -21,7 +21,7 @@
#define ORION_MBUS_DEVBUS_BOOT_ATTR 0x0f
#define ORION_MBUS_DEVBUS_TARGET(cs) 0x01
#define ORION_MBUS_DEVBUS_ATTR(cs) (~(1 << cs))
-#define ORION_MBUS_SRAM_TARGET 0x00
+#define ORION_MBUS_SRAM_TARGET 0x09
#define ORION_MBUS_SRAM_ATTR 0x00
/*
diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c
index 293e2e0..00b7344 100644
--- a/drivers/bus/mvebu-mbus.c
+++ b/drivers/bus/mvebu-mbus.c
@@ -56,6 +56,7 @@
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/debugfs.h>
+#include <linux/log2.h>
/*
* DDR target is the same on all platforms.
@@ -222,12 +223,6 @@
*/
if ((u64)base < wend && end > wbase)
return 0;
-
- /*
- * Check if target/attribute conflicts
- */
- if (target == wtarget && attr == wattr)
- return 0;
}
return 1;
@@ -266,6 +261,17 @@
mbus->soc->win_cfg_offset(win);
u32 ctrl, remap_addr;
+ if (!is_power_of_2(size)) {
+ WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+ return -EINVAL;
+ }
+
+ if ((base & (phys_addr_t)(size - 1)) != 0) {
+ WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+ size);
+ return -EINVAL;
+ }
+
ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
(attr << WIN_CTRL_ATTR_SHIFT) |
(target << WIN_CTRL_TGT_SHIFT) |
@@ -413,6 +419,10 @@
win, (unsigned long long)wbase,
(unsigned long long)(wbase + wsize), wtarget, wattr);
+ if (!is_power_of_2(wsize) ||
+ ((wbase & (u64)(wsize - 1)) != 0))
+ seq_puts(seq, " (Invalid base/size!!)");
+
if (win < mbus->soc->num_remappable_wins) {
seq_printf(seq, " (remap %016llx)\n",
(unsigned long long)wremap);
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
index 110c036..b59a17f 100644
--- a/drivers/memory/mvebu-devbus.c
+++ b/drivers/memory/mvebu-devbus.c
@@ -108,8 +108,19 @@
node->full_name);
return err;
}
- /* Convert bit width to byte width */
- r.bus_width /= 8;
+
+ /*
+ * The bus width is encoded into the register as 0 for 8 bits,
+ * and 1 for 16 bits, so we do the necessary conversion here.
+ */
+ if (r.bus_width == 8)
+ r.bus_width = 0;
+ else if (r.bus_width == 16)
+ r.bus_width = 1;
+ else {
+ dev_err(devbus->dev, "invalid bus width %d\n", r.bus_width);
+ return -EINVAL;
+ }
err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
&r.badr_skew);
diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c
index d3d1cfd..e384e25 100644
--- a/drivers/pci/host/pci-mvebu.c
+++ b/drivers/pci/host/pci-mvebu.c
@@ -293,6 +293,58 @@
return PCIBIOS_SUCCESSFUL;
}
+/*
+ * Remove windows, starting from the largest ones to the smallest
+ * ones.
+ */
+static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
+ phys_addr_t base, size_t size)
+{
+ while (size) {
+ size_t sz = 1 << (fls(size) - 1);
+
+ mvebu_mbus_del_window(base, sz);
+ base += sz;
+ size -= sz;
+ }
+}
+
+/*
+ * MBus windows can only have a power of two size, but PCI BARs do not
+ * have this constraint. Therefore, we have to split the PCI BAR into
+ * areas each having a power of two size. We start from the largest
+ * one (i.e highest order bit set in the size).
+ */
+static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+ unsigned int target, unsigned int attribute,
+ phys_addr_t base, size_t size,
+ phys_addr_t remap)
+{
+ size_t size_mapped = 0;
+
+ while (size) {
+ size_t sz = 1 << (fls(size) - 1);
+ int ret;
+
+ ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+ sz, remap);
+ if (ret) {
+ dev_err(&port->pcie->pdev->dev,
+ "Could not create MBus window at 0x%x, size 0x%x: %d\n",
+ base, sz, ret);
+ mvebu_pcie_del_windows(port, base - size_mapped,
+ size_mapped);
+ return;
+ }
+
+ size -= sz;
+ size_mapped += sz;
+ base += sz;
+ if (remap != MVEBU_MBUS_NO_REMAP)
+ remap += sz;
+ }
+}
+
static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
{
phys_addr_t iobase;
@@ -304,8 +356,8 @@
/* If a window was configured, remove it */
if (port->iowin_base) {
- mvebu_mbus_del_window(port->iowin_base,
- port->iowin_size);
+ mvebu_pcie_del_windows(port, port->iowin_base,
+ port->iowin_size);
port->iowin_base = 0;
port->iowin_size = 0;
}
@@ -331,11 +383,11 @@
port->iowin_base = port->pcie->io.start + iobase;
port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) |
(port->bridge.iolimitupper << 16)) -
- iobase);
+ iobase) + 1;
- mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr,
- port->iowin_base, port->iowin_size,
- iobase);
+ mvebu_pcie_add_windows(port, port->io_target, port->io_attr,
+ port->iowin_base, port->iowin_size,
+ iobase);
}
static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
@@ -346,8 +398,8 @@
/* If a window was configured, remove it */
if (port->memwin_base) {
- mvebu_mbus_del_window(port->memwin_base,
- port->memwin_size);
+ mvebu_pcie_del_windows(port, port->memwin_base,
+ port->memwin_size);
port->memwin_base = 0;
port->memwin_size = 0;
}
@@ -364,10 +416,11 @@
port->memwin_base = ((port->bridge.membase & 0xFFF0) << 16);
port->memwin_size =
(((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) -
- port->memwin_base;
+ port->memwin_base + 1;
- mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr,
- port->memwin_base, port->memwin_size);
+ mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr,
+ port->memwin_base, port->memwin_size,
+ MVEBU_MBUS_NO_REMAP);
}
/*
@@ -743,14 +796,21 @@
/*
* On the PCI-to-PCI bridge side, the I/O windows must have at
- * least a 64 KB size and be aligned on their size, and the
- * memory windows must have at least a 1 MB size and be
- * aligned on their size
+ * least a 64 KB size and the memory windows must have at
+ * least a 1 MB size. Moreover, MBus windows need to have a
+ * base address aligned on their size, and their size must be
+ * a power of two. This means that if the BAR doesn't have a
+ * power of two size, several MBus windows will actually be
+ * created. We need to ensure that the biggest MBus window
+ * (which will be the first one) is aligned on its size, which
+ * explains the rounddown_pow_of_two() being done here.
*/
if (res->flags & IORESOURCE_IO)
- return round_up(start, max_t(resource_size_t, SZ_64K, size));
+ return round_up(start, max_t(resource_size_t, SZ_64K,
+ rounddown_pow_of_two(size)));
else if (res->flags & IORESOURCE_MEM)
- return round_up(start, max_t(resource_size_t, SZ_1M, size));
+ return round_up(start, max_t(resource_size_t, SZ_1M,
+ rounddown_pow_of_two(size)));
else
return start;
}
diff --git a/include/dt-bindings/clk/at91.h b/include/dt-bindings/clock/at91.h
similarity index 100%
rename from include/dt-bindings/clk/at91.h
rename to include/dt-bindings/clock/at91.h