ARM: imx: initial SolidRun HummingBoard support
Add support for the SolidRun HummingBoard. This commit adds support for
the following interfaces on this board:
- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d57c1a6..875af33 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -136,6 +136,7 @@
imx53-mba53.dtb \
imx53-qsb.dtb \
imx53-smd.dtb \
+ imx6dl-hummingboard.dtb \
imx6dl-sabreauto.dtb \
imx6dl-sabresd.dtb \
imx6dl-wandboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/imx6dl-hummingboard.dts
new file mode 100644
index 0000000..fd8fc7c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-hummingboard.dts
@@ -0,0 +1,167 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-microsom.dtsi"
+#include "imx6qdl-microsom-ar8035.dtsi"
+
+/ {
+ model = "SolidRun HummingBoard DL/Solo";
+ compatible = "solidrun,hummingboard", "fsl,imx6dl";
+
+ ir_recv: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio1 2 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: usb-h1-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usbotg_vbus: usb-otg-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 22 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
+
+ codec: spdif-transmitter {
+ compatible = "linux,spdif-dit";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_spdif>;
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ /* IMX6 doesn't implement this yet */
+ spdif-controller = <&spdif>;
+ spdif-out;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
+
+ /*
+ * Not fitted on Carrier-1 board... yet
+ status = "okay";
+
+ rtc: pcf8523@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+ */
+};
+
+&iomuxc {
+ hummingboard {
+ pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
+ >;
+ };
+
+ pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_hummingboard_spdif: hummingboard-spdif {
+ fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+ };
+
+ pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
+ >;
+ };
+
+ pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+ >;
+ };
+ };
+};
+
+&spdif {
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usbotg_vbus>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_hummingboard_usdhc2_aux
+ &pinctrl_hummingboard_usdhc2
+ >;
+ vmmc-supply = <®_3p3v>;
+ cd-gpios = <&gpio1 4 0>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
new file mode 100644
index 0000000..a3cb2ff
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
@@ -0,0 +1,62 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This describes the hookup for an AR8035 to the iMX6 on the SolidRun
+ * MicroSOM.
+ */
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+ phy-mode = "rgmii";
+ phy-reset-duration = <2>;
+ phy-reset-gpios = <&gpio4 15 0>;
+ status = "okay";
+};
+
+&iomuxc {
+ enet {
+ pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ /* AR8035 reset */
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
+ /* AR8035 interrupt */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x80000000
+ /* GPIO16 -> AR8035 25MHz */
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0xc0000000
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x80000000
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1
+ /* AR8035 pin strapping: IO voltage: pull up */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ /* AR8035 pin strapping: PHYADDR#0: pull down */
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x130b0
+ /* AR8035 pin strapping: PHYADDR#1: pull down */
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x130b0
+ /* AR8035 pin strapping: MODE#1: pull up */
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ /* AR8035 pin strapping: MODE#3: pull up */
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ /* AR8035 pin strapping: MODE#0: pull down */
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x130b0
+
+ /*
+ * As the RMII pins are also connected to RGMII
+ * so that an AR8030 can be placed, set these
+ * to high-z with the same pulls as above.
+ * Use the GPIO settings to avoid changing the
+ * input select registers.
+ */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000
+ >;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom.dtsi b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
new file mode 100644
index 0000000..d729d0b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ */
+
+&iomuxc {
+ microsom {
+ pinctrl_microsom_uart1: microsom-uart1 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_microsom_usbotg: microsom-usbotg {
+ /*
+ * Similar to pinctrl_usbotg_2, but we want it
+ * pulled down for a fixed host connection.
+ */
+ fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_uart1>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_usbotg>;
+};