OMAP2+: hwmod: add postsetup state
Allow board files and OMAP core code to control the state that some or
all of the hwmods end up in at the end of _setup() (called by
omap_hwmod_late_init() ). Reimplement the old skip_setup_idle code in
terms of this new postsetup state code.
There are two use-cases for this patch: the !CONFIG_PM_RUNTIME case,
in which all IP blocks should stay enabled after _setup() finishes;
and the MPU watchdog case, in which the watchdog IP block should enter
idle if watchdog coverage of kernel initialization is desired, and
should be disabled otherwise.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 77bf0d1..7362b69 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -312,6 +312,11 @@
return v;
}
+static int _set_hwmod_postsetup_state(struct omap_hwmod *oh, void *data)
+{
+ return omap_hwmod_set_postsetup_state(oh, *(u8 *)data);
+}
+
/*
* Initialize asm_irq_base for entry-macro.S
*/
@@ -333,6 +338,8 @@
void __init omap2_init_common_infrastructure(void)
{
+ u8 postsetup_state;
+
pwrdm_init(powerdomains_omap);
clkdm_init(clockdomains_omap, clkdm_autodeps);
if (cpu_is_omap242x())
@@ -343,6 +350,16 @@
omap3xxx_hwmod_init();
else if (cpu_is_omap44xx())
omap44xx_hwmod_init();
+ else
+ pr_err("Could not init hwmod data - unknown SoC\n");
+
+ /* Set the default postsetup state for all hwmods */
+#ifdef CONFIG_PM_RUNTIME
+ postsetup_state = _HWMOD_STATE_IDLE;
+#else
+ postsetup_state = _HWMOD_STATE_ENABLED;
+#endif
+ omap_hwmod_for_each(_set_hwmod_postsetup_state, &postsetup_state);
omap_pm_if_early_init();
@@ -355,25 +372,16 @@
else if (cpu_is_omap44xx())
omap4xxx_clk_init();
else
- pr_err("Could not init clock framework - unknown CPU\n");
+ pr_err("Could not init clock framework - unknown SoC\n");
}
-/*
- * XXX Ideally, this function will dwindle into nothingness over time;
- * almost all device init code should be possible through initcalls
- * and other generalized mechanisms
- */
void __init omap2_init_common_devices(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1)
{
- u8 skip_setup_idle = 0;
-
omap_serial_early_init();
-#ifndef CONFIG_PM_RUNTIME
- skip_setup_idle = 1;
-#endif
- omap_hwmod_late_init(skip_setup_idle);
+ omap_hwmod_late_init();
+
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
_omap2_init_reprogram_sdrc();