drm/i915: Only set the down rps limit when at the loweset frequency
The power docs say that when the gt leaves rc6, it is in the lowest
frequency and only about 25 usec later will switch to the frequency
selected in GEN6_RPNSWREQ. If the downclock limit expires in that
window and the down limit is set to the lowest possible frequency, the
hw will not send the down interrupt. Which leads to a too high gpu
clock and wasted power.
Chris Wilson already worked on this with
commit 7b9e0ae6da0a7eaf2680a1a788f08df123724f3b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Apr 28 08:56:39 2012 +0100
drm/i915: Always update RPS interrupts thresholds along with
frequency
but got the logic inverted: The current code set the down limit as
long as we haven't reached it. Instead of only once with reached the
lowest frequency.
Note that we can't always set the downclock limit to 0, because
otherwise the hw will keep on bugging us with downclock request irqs
once the lowest level is reached.
For similar reasons also always set the upclock limit, otherwise the
hw might poke us again with interrupts.
v2: Chris Wilson noticed that the limit reg is also computed in
sanitize_pm. To avoid duplication, extract the code into a common
function.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index 85d1b1c..e8727da 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -2267,21 +2267,33 @@
}
-void gen6_set_rps(struct drm_device *dev, u8 val)
+static u32 gen6_rps_limits(struct drm_i915_private *dev_priv, u8 val)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
u32 limits;
limits = 0;
if (val >= dev_priv->max_delay)
val = dev_priv->max_delay;
- else
- limits |= dev_priv->max_delay << 24;
+ limits |= dev_priv->max_delay << 24;
- if (val <= dev_priv->min_delay)
+ /* Only set the down limit when we've reached the lowest level to avoid
+ * getting more interrupts, otherwise leave this clear. This prevents a
+ * race in the hw when coming out of rc6: There's a tiny window where
+ * the hw runs at the minimal clock before selecting the desired
+ * frequency, if the down threshold expires in that window we will not
+ * receive a down interrupt. */
+ if (val <= dev_priv->min_delay) {
val = dev_priv->min_delay;
- else
limits |= dev_priv->min_delay << 16;
+ }
+
+ return limits;
+}
+
+void gen6_set_rps(struct drm_device *dev, u8 val)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 limits = gen6_rps_limits(dev_priv, val);
if (val == dev_priv->cur_delay)
return;
@@ -3741,25 +3753,20 @@
static void gen6_sanitize_pm(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 limits, delay, old;
+ u32 limits, current_limits;
gen6_gt_force_wake_get(dev_priv);
- old = limits = I915_READ(GEN6_RP_INTERRUPT_LIMITS);
+ current_limits = I915_READ(GEN6_RP_INTERRUPT_LIMITS);
/* Make sure we continue to get interrupts
* until we hit the minimum or maximum frequencies.
*/
- limits &= ~(0x3f << 16 | 0x3f << 24);
- delay = dev_priv->cur_delay;
- if (delay < dev_priv->max_delay)
- limits |= (dev_priv->max_delay & 0x3f) << 24;
- if (delay > dev_priv->min_delay)
- limits |= (dev_priv->min_delay & 0x3f) << 16;
+ limits = gen6_rps_limits(dev_priv, dev_priv->cur_delay);
- if (old != limits) {
+ if (current_limits != limits) {
/* Note that the known failure case is to read back 0. */
DRM_DEBUG_DRIVER("Power management discrepancy: GEN6_RP_INTERRUPT_LIMITS "
- "expected %08x, was %08x\n", limits, old);
+ "expected %08x, was %08x\n", limits, current_limits);
I915_WRITE(GEN6_RP_INTERRUPT_LIMITS, limits);
}