| /* |
| * Common support for CompuLab CM-T3x30 CoMs |
| */ |
| |
| #include "omap3-cm-t3x.dtsi" |
| |
| / { |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vcc>; |
| }; |
| }; |
| |
| vddvario: regulator-vddvario { |
| compatible = "regulator-fixed"; |
| regulator-name = "vddvario"; |
| regulator-always-on; |
| }; |
| |
| vdd33a: regulator-vdd33a { |
| compatible = "regulator-fixed"; |
| regulator-name = "vdd33a"; |
| regulator-always-on; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| |
| smsc1_pins: pinmux_smsc1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ |
| OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ |
| >; |
| }; |
| |
| hsusb0_pins: pinmux_hsusb0_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ |
| OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ |
| OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ |
| OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ |
| OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */ |
| OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ |
| OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ |
| OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */ |
| OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */ |
| OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */ |
| OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */ |
| OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ |
| >; |
| }; |
| }; |
| |
| &gpmc { |
| ranges = <5 0 0x2c000000 0x01000000>; |
| |
| smsc1: ethernet@5,0 { |
| compatible = "smsc,lan9221", "smsc,lan9115"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smsc1_pins>; |
| interrupt-parent = <&gpio6>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| reg = <5 0 0xff>; |
| bank-width = <2>; |
| gpmc,mux-add-data; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <186>; |
| gpmc,cs-wr-off-ns = <186>; |
| gpmc,adv-on-ns = <12>; |
| gpmc,adv-rd-off-ns = <48>; |
| gpmc,adv-wr-off-ns = <48>; |
| gpmc,oe-on-ns = <54>; |
| gpmc,oe-off-ns = <168>; |
| gpmc,we-on-ns = <54>; |
| gpmc,we-off-ns = <168>; |
| gpmc,rd-cycle-ns = <186>; |
| gpmc,wr-cycle-ns = <186>; |
| gpmc,access-ns = <114>; |
| gpmc,page-burst-access-ns = <6>; |
| gpmc,bus-turnaround-ns = <12>; |
| gpmc,cycle2cycle-delay-ns = <18>; |
| gpmc,wr-data-mux-bus-ns = <90>; |
| gpmc,wr-access-ns = <186>; |
| gpmc,cycle2cycle-samecsen; |
| gpmc,cycle2cycle-diffcsen; |
| vddvario-supply = <&vddvario>; |
| vdd33a-supply = <&vdd33a>; |
| reg-io-width = <4>; |
| smsc,save-mac-address; |
| }; |
| }; |
| |
| &i2c1 { |
| twl: twl@48 { |
| reg = <0x48>; |
| interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| interrupt-parent = <&intc>; |
| }; |
| }; |
| |
| #include "twl4030.dtsi" |
| #include "twl4030_omap3.dtsi" |
| |
| &mmc1 { |
| vmmc-supply = <&vmmc1>; |
| }; |
| |
| &twl_gpio { |
| ti,use-leds; |
| /* pullups: BIT(0) */ |
| ti,pullups = <0x000001>; |
| }; |
| |
| &hsusb1_phy { |
| reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &hsusb2_phy { |
| reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &usb_otg_hs { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hsusb0_pins>; |
| interface-type = <0>; |
| usb-phy = <&usb2_phy>; |
| phys = <&usb2_phy>; |
| phy-names = "usb2-phy"; |
| mode = <3>; |
| power = <50>; |
| }; |