| /* |
| * EHCI HCD (Host Controller Driver) PCI Bus Glue. |
| * |
| * Copyright (c) 2000-2004 by David Brownell |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY |
| * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License |
| * for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software Foundation, |
| * Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #ifndef CONFIG_PCI |
| #error "This file is PCI bus glue. CONFIG_PCI must be defined." |
| #endif |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| /* called after powerup, by probe or system-pm "wakeup" */ |
| static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev) |
| { |
| int retval; |
| |
| /* we expect static quirk code to handle the "extended capabilities" |
| * (currently just BIOS handoff) allowed starting with EHCI 0.96 |
| */ |
| |
| /* PCI Memory-Write-Invalidate cycle support is optional (uncommon) */ |
| retval = pci_set_mwi(pdev); |
| if (!retval) |
| ehci_dbg(ehci, "MWI active\n"); |
| |
| return 0; |
| } |
| |
| /* called during probe() after chip reset completes */ |
| static int ehci_pci_setup(struct usb_hcd *hcd) |
| { |
| struct ehci_hcd *ehci = hcd_to_ehci(hcd); |
| struct pci_dev *pdev = to_pci_dev(hcd->self.controller); |
| struct pci_dev *p_smbus; |
| u8 rev; |
| u32 temp; |
| int retval; |
| |
| switch (pdev->vendor) { |
| case PCI_VENDOR_ID_TOSHIBA_2: |
| /* celleb's companion chip */ |
| if (pdev->device == 0x01b5) { |
| #ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO |
| ehci->big_endian_mmio = 1; |
| #else |
| ehci_warn(ehci, |
| "unsupported big endian Toshiba quirk\n"); |
| #endif |
| } |
| break; |
| } |
| |
| ehci->caps = hcd->regs; |
| ehci->regs = hcd->regs + |
| HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); |
| |
| dbg_hcs_params(ehci, "reset"); |
| dbg_hcc_params(ehci, "reset"); |
| |
| /* ehci_init() causes memory for DMA transfers to be |
| * allocated. Thus, any vendor-specific workarounds based on |
| * limiting the type of memory used for DMA transfers must |
| * happen before ehci_init() is called. */ |
| switch (pdev->vendor) { |
| case PCI_VENDOR_ID_NVIDIA: |
| /* NVidia reports that certain chips don't handle |
| * QH, ITD, or SITD addresses above 2GB. (But TD, |
| * data buffer, and periodic schedule are normal.) |
| */ |
| switch (pdev->device) { |
| case 0x003c: /* MCP04 */ |
| case 0x005b: /* CK804 */ |
| case 0x00d8: /* CK8 */ |
| case 0x00e8: /* CK8S */ |
| if (pci_set_consistent_dma_mask(pdev, |
| DMA_BIT_MASK(31)) < 0) |
| ehci_warn(ehci, "can't enable NVidia " |
| "workaround for >2GB RAM\n"); |
| break; |
| } |
| break; |
| } |
| |
| /* cache this readonly data; minimize chip reads */ |
| ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); |
| |
| retval = ehci_halt(ehci); |
| if (retval) |
| return retval; |
| |
| /* data structure init */ |
| retval = ehci_init(hcd); |
| if (retval) |
| return retval; |
| |
| switch (pdev->vendor) { |
| case PCI_VENDOR_ID_INTEL: |
| ehci->need_io_watchdog = 0; |
| break; |
| case PCI_VENDOR_ID_TDI: |
| if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) { |
| hcd->has_tt = 1; |
| tdi_reset(ehci); |
| } |
| break; |
| case PCI_VENDOR_ID_AMD: |
| /* AMD8111 EHCI doesn't work, according to AMD errata */ |
| if (pdev->device == 0x7463) { |
| ehci_info(ehci, "ignoring AMD8111 (errata)\n"); |
| retval = -EIO; |
| goto done; |
| } |
| break; |
| case PCI_VENDOR_ID_NVIDIA: |
| switch (pdev->device) { |
| /* Some NForce2 chips have problems with selective suspend; |
| * fixed in newer silicon. |
| */ |
| case 0x0068: |
| if (pdev->revision < 0xa4) |
| ehci->no_selective_suspend = 1; |
| break; |
| } |
| break; |
| case PCI_VENDOR_ID_VIA: |
| if (pdev->device == 0x3104 && (pdev->revision & 0xf0) == 0x60) { |
| u8 tmp; |
| |
| /* The VT6212 defaults to a 1 usec EHCI sleep time which |
| * hogs the PCI bus *badly*. Setting bit 5 of 0x4B makes |
| * that sleep time use the conventional 10 usec. |
| */ |
| pci_read_config_byte(pdev, 0x4b, &tmp); |
| if (tmp & 0x20) |
| break; |
| pci_write_config_byte(pdev, 0x4b, tmp | 0x20); |
| } |
| break; |
| case PCI_VENDOR_ID_ATI: |
| /* SB600 and old version of SB700 have a bug in EHCI controller, |
| * which causes usb devices lose response in some cases. |
| */ |
| if ((pdev->device == 0x4386) || (pdev->device == 0x4396)) { |
| p_smbus = pci_get_device(PCI_VENDOR_ID_ATI, |
| PCI_DEVICE_ID_ATI_SBX00_SMBUS, |
| NULL); |
| if (!p_smbus) |
| break; |
| rev = p_smbus->revision; |
| if ((pdev->device == 0x4386) || (rev == 0x3a) |
| || (rev == 0x3b)) { |
| u8 tmp; |
| ehci_info(ehci, "applying AMD SB600/SB700 USB " |
| "freeze workaround\n"); |
| pci_read_config_byte(pdev, 0x53, &tmp); |
| pci_write_config_byte(pdev, 0x53, tmp | (1<<3)); |
| } |
| pci_dev_put(p_smbus); |
| } |
| break; |
| } |
| |
| /* optional debug port, normally in the first BAR */ |
| temp = pci_find_capability(pdev, 0x0a); |
| if (temp) { |
| pci_read_config_dword(pdev, temp, &temp); |
| temp >>= 16; |
| if ((temp & (3 << 13)) == (1 << 13)) { |
| temp &= 0x1fff; |
| ehci->debug = ehci_to_hcd(ehci)->regs + temp; |
| temp = ehci_readl(ehci, &ehci->debug->control); |
| ehci_info(ehci, "debug port %d%s\n", |
| HCS_DEBUG_PORT(ehci->hcs_params), |
| (temp & DBGP_ENABLED) |
| ? " IN USE" |
| : ""); |
| if (!(temp & DBGP_ENABLED)) |
| ehci->debug = NULL; |
| } |
| } |
| |
| ehci_reset(ehci); |
| |
| /* at least the Genesys GL880S needs fixup here */ |
| temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params); |
| temp &= 0x0f; |
| if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) { |
| ehci_dbg(ehci, "bogus port configuration: " |
| "cc=%d x pcc=%d < ports=%d\n", |
| HCS_N_CC(ehci->hcs_params), |
| HCS_N_PCC(ehci->hcs_params), |
| HCS_N_PORTS(ehci->hcs_params)); |
| |
| switch (pdev->vendor) { |
| case 0x17a0: /* GENESYS */ |
| /* GL880S: should be PORTS=2 */ |
| temp |= (ehci->hcs_params & ~0xf); |
| ehci->hcs_params = temp; |
| break; |
| case PCI_VENDOR_ID_NVIDIA: |
| /* NF4: should be PCC=10 */ |
| break; |
| } |
| } |
| |
| /* Serial Bus Release Number is at PCI 0x60 offset */ |
| pci_read_config_byte(pdev, 0x60, &ehci->sbrn); |
| |
| /* Keep this around for a while just in case some EHCI |
| * implementation uses legacy PCI PM support. This test |
| * can be removed on 17 Dec 2009 if the dev_warn() hasn't |
| * been triggered by then. |
| */ |
| if (!device_can_wakeup(&pdev->dev)) { |
| u16 port_wake; |
| |
| pci_read_config_word(pdev, 0x62, &port_wake); |
| if (port_wake & 0x0001) { |
| dev_warn(&pdev->dev, "Enabling legacy PCI PM\n"); |
| device_set_wakeup_capable(&pdev->dev, 1); |
| } |
| } |
| |
| #ifdef CONFIG_USB_SUSPEND |
| /* REVISIT: the controller works fine for wakeup iff the root hub |
| * itself is "globally" suspended, but usbcore currently doesn't |
| * understand such things. |
| * |
| * System suspend currently expects to be able to suspend the entire |
| * device tree, device-at-a-time. If we failed selective suspend |
| * reports, system suspend would fail; so the root hub code must claim |
| * success. That's lying to usbcore, and it matters for runtime |
| * PM scenarios with selective suspend and remote wakeup... |
| */ |
| if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev)) |
| ehci_warn(ehci, "selective suspend/wakeup unavailable\n"); |
| #endif |
| |
| ehci_port_power(ehci, 1); |
| retval = ehci_pci_reinit(ehci, pdev); |
| done: |
| return retval; |
| } |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_PM |
| |
| /* suspend/resume, section 4.3 */ |
| |
| /* These routines rely on the PCI bus glue |
| * to handle powerdown and wakeup, and currently also on |
| * transceivers that don't need any software attention to set up |
| * the right sort of wakeup. |
| * Also they depend on separate root hub suspend/resume. |
| */ |
| |
| static int ehci_pci_suspend(struct usb_hcd *hcd) |
| { |
| struct ehci_hcd *ehci = hcd_to_ehci(hcd); |
| unsigned long flags; |
| int rc = 0; |
| |
| if (time_before(jiffies, ehci->next_statechange)) |
| msleep(10); |
| |
| /* Root hub was already suspended. Disable irq emission and |
| * mark HW unaccessible, bail out if RH has been resumed. Use |
| * the spinlock to properly synchronize with possible pending |
| * RH suspend or resume activity. |
| * |
| * This is still racy as hcd->state is manipulated outside of |
| * any locks =P But that will be a different fix. |
| */ |
| spin_lock_irqsave (&ehci->lock, flags); |
| if (hcd->state != HC_STATE_SUSPENDED) { |
| rc = -EINVAL; |
| goto bail; |
| } |
| ehci_writel(ehci, 0, &ehci->regs->intr_enable); |
| (void)ehci_readl(ehci, &ehci->regs->intr_enable); |
| |
| clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); |
| bail: |
| spin_unlock_irqrestore (&ehci->lock, flags); |
| |
| // could save FLADJ in case of Vaux power loss |
| // ... we'd only use it to handle clock skew |
| |
| return rc; |
| } |
| |
| static int ehci_pci_resume(struct usb_hcd *hcd, bool hibernated) |
| { |
| struct ehci_hcd *ehci = hcd_to_ehci(hcd); |
| struct pci_dev *pdev = to_pci_dev(hcd->self.controller); |
| |
| // maybe restore FLADJ |
| |
| if (time_before(jiffies, ehci->next_statechange)) |
| msleep(100); |
| |
| /* Mark hardware accessible again as we are out of D3 state by now */ |
| set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); |
| |
| /* If CF is still set and we aren't resuming from hibernation |
| * then we maintained PCI Vaux power. |
| * Just undo the effect of ehci_pci_suspend(). |
| */ |
| if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF && |
| !hibernated) { |
| int mask = INTR_MASK; |
| |
| if (!hcd->self.root_hub->do_remote_wakeup) |
| mask &= ~STS_PCD; |
| ehci_writel(ehci, mask, &ehci->regs->intr_enable); |
| ehci_readl(ehci, &ehci->regs->intr_enable); |
| return 0; |
| } |
| |
| usb_root_hub_lost_power(hcd->self.root_hub); |
| |
| /* Else reset, to cope with power loss or flush-to-storage |
| * style "resume" having let BIOS kick in during reboot. |
| */ |
| (void) ehci_halt(ehci); |
| (void) ehci_reset(ehci); |
| (void) ehci_pci_reinit(ehci, pdev); |
| |
| /* emptying the schedule aborts any urbs */ |
| spin_lock_irq(&ehci->lock); |
| if (ehci->reclaim) |
| end_unlink_async(ehci); |
| ehci_work(ehci); |
| spin_unlock_irq(&ehci->lock); |
| |
| ehci_writel(ehci, ehci->command, &ehci->regs->command); |
| ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag); |
| ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */ |
| |
| /* here we "know" root ports should always stay powered */ |
| ehci_port_power(ehci, 1); |
| |
| hcd->state = HC_STATE_SUSPENDED; |
| return 0; |
| } |
| #endif |
| |
| static const struct hc_driver ehci_pci_hc_driver = { |
| .description = hcd_name, |
| .product_desc = "EHCI Host Controller", |
| .hcd_priv_size = sizeof(struct ehci_hcd), |
| |
| /* |
| * generic hardware linkage |
| */ |
| .irq = ehci_irq, |
| .flags = HCD_MEMORY | HCD_USB2, |
| |
| /* |
| * basic lifecycle operations |
| */ |
| .reset = ehci_pci_setup, |
| .start = ehci_run, |
| #ifdef CONFIG_PM |
| .pci_suspend = ehci_pci_suspend, |
| .pci_resume = ehci_pci_resume, |
| #endif |
| .stop = ehci_stop, |
| .shutdown = ehci_shutdown, |
| |
| /* |
| * managing i/o requests and associated device resources |
| */ |
| .urb_enqueue = ehci_urb_enqueue, |
| .urb_dequeue = ehci_urb_dequeue, |
| .endpoint_disable = ehci_endpoint_disable, |
| .endpoint_reset = ehci_endpoint_reset, |
| |
| /* |
| * scheduling support |
| */ |
| .get_frame_number = ehci_get_frame, |
| |
| /* |
| * root hub support |
| */ |
| .hub_status_data = ehci_hub_status_data, |
| .hub_control = ehci_hub_control, |
| .bus_suspend = ehci_bus_suspend, |
| .bus_resume = ehci_bus_resume, |
| .relinquish_port = ehci_relinquish_port, |
| .port_handed_over = ehci_port_handed_over, |
| |
| .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, |
| }; |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| /* PCI driver selection metadata; PCI hotplugging uses this */ |
| static const struct pci_device_id pci_ids [] = { { |
| /* handle any USB 2.0 EHCI controller */ |
| PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_EHCI, ~0), |
| .driver_data = (unsigned long) &ehci_pci_hc_driver, |
| }, |
| { /* end: all zeroes */ } |
| }; |
| MODULE_DEVICE_TABLE(pci, pci_ids); |
| |
| /* pci driver glue; this is a "new style" PCI driver module */ |
| static struct pci_driver ehci_pci_driver = { |
| .name = (char *) hcd_name, |
| .id_table = pci_ids, |
| |
| .probe = usb_hcd_pci_probe, |
| .remove = usb_hcd_pci_remove, |
| .shutdown = usb_hcd_pci_shutdown, |
| |
| #ifdef CONFIG_PM_SLEEP |
| .driver = { |
| .pm = &usb_hcd_pci_pm_ops |
| }, |
| #endif |
| }; |