Blackfin: clean up isp1362 board resources
Drop the CONFIG_USB_ISP1362_BFIN_GPIO_IRQ Kconfig as it never made it into
mainline and it was a bad interface into the board resources. For boards
that actually used this, replace it with an actual IRQ define. For boards
that didn't, simply drop the resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index f1996b1..40b9934 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -15,9 +15,6 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/etherdevice.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
#include <linux/i2c.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
@@ -317,45 +314,6 @@
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20360000,
- .end = 0x20360000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20360004,
- .end = 0x20360004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
static struct platform_device bfin_mii_bus = {
.name = "bfin_mii_bus",
@@ -841,10 +799,6 @@
&sl811_hcd_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
&bfin_isp1760_device,
#endif
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 45db07b..6ffbefc 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -13,9 +13,6 @@
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
#include <linux/i2c.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
@@ -373,45 +370,6 @@
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20360000,
- .end = 0x20360000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20360004,
- .end = 0x20360004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
static struct platform_device bfin_mii_bus = {
.name = "bfin_mii_bus",
@@ -918,10 +876,6 @@
&sl811_hcd_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
&bfin_isp1760_device,
#endif
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 9ba2904..4e0afda 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -13,9 +13,6 @@
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
@@ -147,45 +144,6 @@
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20360000,
- .end = 0x20360000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20360004,
- .end = 0x20360004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
static struct platform_device bfin_mii_bus = {
.name = "bfin_mii_bus",
@@ -492,10 +450,6 @@
&sl811_hcd_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
&smc91x_device,
#endif
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 6a09b71..514d994 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -272,8 +272,8 @@
.end = 0x20360004,
.flags = IORESOURCE_MEM,
}, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+ .start = IRQ_PF3,
+ .end = IRQ_PF3,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};