rtc: omap: add support for pmic_power_en
Add new property "ti,system-power-controller" to register the RTC as a
power-off handler.
Some RTC IP revisions can control an external PMIC via the pmic_power_en
pin, which can be configured to transition to OFF on ALARM2 events and
back to ON on subsequent ALARM (wakealarm) events.
This is based on earlier work by Colin Foe-Parker and AnilKumar Ch. [1]
[1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg82127.html
[akpm@linux-foundation.org: add comment]
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Colin Foe-Parker <colin.foeparker@logicpd.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c
index c508e45..e83f51a 100644
--- a/drivers/rtc/rtc-omap.c
+++ b/drivers/rtc/rtc-omap.c
@@ -68,6 +68,15 @@
#define OMAP_RTC_IRQWAKEEN 0x7c
+#define OMAP_RTC_ALARM2_SECONDS_REG 0x80
+#define OMAP_RTC_ALARM2_MINUTES_REG 0x84
+#define OMAP_RTC_ALARM2_HOURS_REG 0x88
+#define OMAP_RTC_ALARM2_DAYS_REG 0x8c
+#define OMAP_RTC_ALARM2_MONTHS_REG 0x90
+#define OMAP_RTC_ALARM2_YEARS_REG 0x94
+
+#define OMAP_RTC_PMIC_REG 0x98
+
/* OMAP_RTC_CTRL_REG bit fields: */
#define OMAP_RTC_CTRL_SPLIT BIT(7)
#define OMAP_RTC_CTRL_DISABLE BIT(6)
@@ -80,6 +89,7 @@
/* OMAP_RTC_STATUS_REG bit fields: */
#define OMAP_RTC_STATUS_POWER_UP BIT(7)
+#define OMAP_RTC_STATUS_ALARM2 BIT(7)
#define OMAP_RTC_STATUS_ALARM BIT(6)
#define OMAP_RTC_STATUS_1D_EVENT BIT(5)
#define OMAP_RTC_STATUS_1H_EVENT BIT(4)
@@ -89,6 +99,7 @@
#define OMAP_RTC_STATUS_BUSY BIT(0)
/* OMAP_RTC_INTERRUPTS_REG bit fields: */
+#define OMAP_RTC_INTERRUPTS_IT_ALARM2 BIT(4)
#define OMAP_RTC_INTERRUPTS_IT_ALARM BIT(3)
#define OMAP_RTC_INTERRUPTS_IT_TIMER BIT(2)
@@ -98,6 +109,9 @@
/* OMAP_RTC_IRQWAKEEN bit fields: */
#define OMAP_RTC_IRQWAKEEN_ALARM_WAKEEN BIT(1)
+/* OMAP_RTC_PMIC bit fields: */
+#define OMAP_RTC_PMIC_POWER_EN_EN BIT(16)
+
/* OMAP_RTC_KICKER values */
#define KICK0_VALUE 0x83e70b13
#define KICK1_VALUE 0x95a4f1e0
@@ -106,6 +120,7 @@
bool has_32kclk_en;
bool has_kicker;
bool has_irqwakeen;
+ bool has_pmic_mode;
bool has_power_up_reset;
};
@@ -115,6 +130,7 @@
int irq_alarm;
int irq_timer;
u8 interrupts_reg;
+ bool is_pmic_controller;
const struct omap_rtc_device_type *type;
};
@@ -345,6 +361,70 @@
return 0;
}
+static struct omap_rtc *omap_rtc_power_off_rtc;
+
+/*
+ * omap_rtc_poweroff: RTC-controlled power off
+ *
+ * The RTC can be used to control an external PMIC via the pmic_power_en pin,
+ * which can be configured to transition to OFF on ALARM2 events.
+ *
+ * Notes:
+ * The two-second alarm offset is the shortest offset possible as the alarm
+ * registers must be set before the next timer update and the offset
+ * calculation is too heavy for everything to be done within a single access
+ * period (~15 us).
+ *
+ * Called with local interrupts disabled.
+ */
+static void omap_rtc_power_off(void)
+{
+ struct omap_rtc *rtc = omap_rtc_power_off_rtc;
+ struct rtc_time tm;
+ unsigned long now;
+ u32 val;
+
+ /* enable pmic_power_en control */
+ val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
+ rtc_writel(rtc, OMAP_RTC_PMIC_REG, val | OMAP_RTC_PMIC_POWER_EN_EN);
+
+ /* set alarm two seconds from now */
+ omap_rtc_read_time_raw(rtc, &tm);
+ bcd2tm(&tm);
+ rtc_tm_to_time(&tm, &now);
+ rtc_time_to_tm(now + 2, &tm);
+
+ if (tm2bcd(&tm) < 0) {
+ dev_err(&rtc->rtc->dev, "power off failed\n");
+ return;
+ }
+
+ rtc_wait_not_busy(rtc);
+
+ rtc_write(rtc, OMAP_RTC_ALARM2_SECONDS_REG, tm.tm_sec);
+ rtc_write(rtc, OMAP_RTC_ALARM2_MINUTES_REG, tm.tm_min);
+ rtc_write(rtc, OMAP_RTC_ALARM2_HOURS_REG, tm.tm_hour);
+ rtc_write(rtc, OMAP_RTC_ALARM2_DAYS_REG, tm.tm_mday);
+ rtc_write(rtc, OMAP_RTC_ALARM2_MONTHS_REG, tm.tm_mon);
+ rtc_write(rtc, OMAP_RTC_ALARM2_YEARS_REG, tm.tm_year);
+
+ /*
+ * enable ALARM2 interrupt
+ *
+ * NOTE: this fails on AM3352 if rtc_write (writeb) is used
+ */
+ val = rtc_read(rtc, OMAP_RTC_INTERRUPTS_REG);
+ rtc_writel(rtc, OMAP_RTC_INTERRUPTS_REG,
+ val | OMAP_RTC_INTERRUPTS_IT_ALARM2);
+
+ /*
+ * Wait for alarm to trigger (within two seconds) and external PMIC to
+ * power off the system. Add a 500 ms margin for external latencies
+ * (e.g. debounce circuits).
+ */
+ mdelay(2500);
+}
+
static struct rtc_class_ops omap_rtc_ops = {
.read_time = omap_rtc_read_time,
.set_time = omap_rtc_set_time,
@@ -361,6 +441,7 @@
.has_32kclk_en = true,
.has_kicker = true,
.has_irqwakeen = true,
+ .has_pmic_mode = true,
};
static const struct omap_rtc_device_type omap_rtc_da830_type = {
@@ -412,6 +493,9 @@
of_id = of_match_device(omap_rtc_of_match, &pdev->dev);
if (of_id) {
rtc->type = of_id->data;
+ rtc->is_pmic_controller = rtc->type->has_pmic_mode &&
+ of_property_read_bool(pdev->dev.of_node,
+ "ti,system-power-controller");
} else {
id_entry = platform_get_device_id(pdev);
rtc->type = (void *)id_entry->driver_data;
@@ -460,6 +544,9 @@
mask = OMAP_RTC_STATUS_ALARM;
+ if (rtc->type->has_pmic_mode)
+ mask |= OMAP_RTC_STATUS_ALARM2;
+
if (rtc->type->has_power_up_reset) {
mask |= OMAP_RTC_STATUS_POWER_UP;
if (reg & OMAP_RTC_STATUS_POWER_UP)
@@ -520,6 +607,13 @@
goto err;
}
+ if (rtc->is_pmic_controller) {
+ if (!pm_power_off) {
+ omap_rtc_power_off_rtc = rtc;
+ pm_power_off = omap_rtc_power_off;
+ }
+ }
+
return 0;
err:
@@ -536,6 +630,12 @@
{
struct omap_rtc *rtc = platform_get_drvdata(pdev);
+ if (pm_power_off == omap_rtc_power_off &&
+ omap_rtc_power_off_rtc == rtc) {
+ pm_power_off = NULL;
+ omap_rtc_power_off_rtc = NULL;
+ }
+
device_init_wakeup(&pdev->dev, 0);
/* leave rtc running, but disable irqs */