Merge tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
index 3f6a524..32f4a2d 100644
--- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -1,13 +1,16 @@
== Amlogic Meson pinmux controller ==
Required properties for the root node:
- - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
+ - compatible: one of "amlogic,meson8-cbus-pinctrl"
+ "amlogic,meson8b-cbus-pinctrl"
+ "amlogic,meson8-aobus-pinctrl"
+ "amlogic,meson8b-aobus-pinctrl"
- reg: address and size of registers controlling irq functionality
=== GPIO sub-nodes ===
-The 2 power domains of the controller (regular and always-on) are
-represented as sub-nodes and each of them acts as a GPIO controller.
+The GPIO bank for the controller is represented as a sub-node and it acts as a
+GPIO controller.
Required properties for sub-nodes are:
- reg: should contain address and size for mux, pull-enable, pull and
@@ -18,10 +21,6 @@
- gpio-controller: identifies the node as a gpio controller
- #gpio-cells: must be 2
-Valid sub-node names are:
- - "banks" for the regular domain
- - "ao-bank" for the always-on domain
-
=== Other sub-nodes ===
Child nodes without the "gpio-controller" represent some desired
@@ -45,7 +44,7 @@
=== Example ===
pinctrl: pinctrl@c1109880 {
- compatible = "amlogic,meson8-pinctrl";
+ compatible = "amlogic,meson8-cbus-pinctrl";
reg = <0xc1109880 0x10>;
#address-cells = <1>;
#size-cells = <1>;
@@ -61,15 +60,6 @@
#gpio-cells = <2>;
};
- gpio_ao: ao-bank@c1108030 {
- reg = <0xc8100014 0x4>,
- <0xc810002c 0x4>,
- <0xc8100024 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
nand {
mux {
groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
@@ -79,18 +69,4 @@
function = "nand";
};
};
-
- uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a",
- "uart_cts_ao_a", "uart_rts_ao_a";
- function = "uart_ao";
- };
-
- conf {
- pins = "GPIOAO_0", "GPIOAO_1",
- "GPIOAO_2", "GPIOAO_3";
- bias-disable;
- };
- };
};
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi
index 3710755..85d2c37 100644
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@@ -117,7 +117,7 @@
};
/* USB part of the eSATA/USB 2.0 port */
- usb@50000 {
+ usb@58000 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index a2ddcb8..45619f6 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -91,8 +91,8 @@
clock-frequency = <141666666>;
};
- pinctrl: pinctrl@c1109880 {
- compatible = "amlogic,meson8-pinctrl";
+ pinctrl_cbus: pinctrl@c1109880 {
+ compatible = "amlogic,meson8-cbus-pinctrl";
reg = <0xc1109880 0x10>;
#address-cells = <1>;
#size-cells = <1>;
@@ -108,29 +108,6 @@
#gpio-cells = <2>;
};
- gpio_ao: ao-bank@c1108030 {
- reg = <0xc8100014 0x4>,
- <0xc810002c 0x4>,
- <0xc8100024 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- uart_ao_a_pins: uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a";
- function = "uart_ao";
- };
- };
-
- i2c_ao_pins: i2c_mst_ao {
- mux {
- groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao";
- function = "i2c_mst_ao";
- };
- };
-
spi_nor_pins: nor {
mux {
groups = "nor_d", "nor_q", "nor_c", "nor_cs";
@@ -157,4 +134,34 @@
};
};
+ pinctrl_aobus: pinctrl@c8100084 {
+ compatible = "amlogic,meson8-aobus-pinctrl";
+ reg = <0xc8100084 0xc>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio_ao: ao-bank@c1108030 {
+ reg = <0xc8100014 0x4>,
+ <0xc810002c 0x4>,
+ <0xc8100024 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+
+ i2c_ao_pins: i2c_mst_ao {
+ mux {
+ groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao";
+ function = "i2c_mst_ao";
+ };
+ };
+ };
}; /* end of / */
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index 8bad557..2bfe401 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -155,8 +155,8 @@
reg = <0xc1108000 0x4>, <0xc1104000 0x460>;
};
- pinctrl: pinctrl@c1109880 {
- compatible = "amlogic,meson8b-pinctrl";
+ pinctrl_cbus: pinctrl@c1109880 {
+ compatible = "amlogic,meson8b-cbus-pinctrl";
reg = <0xc1109880 0x10>;
#address-cells = <1>;
#size-cells = <1>;
@@ -171,6 +171,14 @@
gpio-controller;
#gpio-cells = <2>;
};
+ };
+
+ pinctrl_aobus: pinctrl@c8100084 {
+ compatible = "amlogic,meson8b-aobus-pinctrl";
+ reg = <0xc8100084 0xc>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
gpio_ao: ao-bank@c1108030 {
reg = <0xc8100014 0x4>,
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 0ad71b8..cc6e28f 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -661,6 +661,7 @@
};
&pcie_bus_clk {
+ clock-frequency = <100000000>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 6c08314..a9285d9 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -143,19 +143,11 @@
};
&pfc {
- pinctrl-0 = <&scif_clk_pins>;
- pinctrl-names = "default";
-
scif0_pins: serial0 {
renesas,groups = "scif0_data_d";
renesas,function = "scif0";
};
- scif_clk_pins: scif_clk {
- renesas,groups = "scif_clk";
- renesas,function = "scif_clk";
- };
-
ether_pins: ether {
renesas,groups = "eth_link", "eth_mdio", "eth_rmii";
renesas,function = "eth";
@@ -229,11 +221,6 @@
status = "okay";
};
-&scif_clk {
- clock-frequency = <14745600>;
- status = "okay";
-};
-
ðer {
pinctrl-0 = <ðer_pins &phy1_pins>;
pinctrl-names = "default";
@@ -414,6 +401,7 @@
};
&pcie_bus_clk {
+ clock-frequency = <100000000>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 6439f05..1cd1b6a 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1083,9 +1083,8 @@
pcie_bus_clk: pcie_bus_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <100000000>;
+ clock-frequency = <0>;
clock-output-names = "pcie_bus";
- status = "disabled";
};
/* External SCIF clock */
@@ -1094,7 +1093,6 @@
#clock-cells = <0>;
/* This value must be overridden by the board. */
clock-frequency = <0>;
- status = "disabled";
};
/* External USB clock - can be overridden by the board */
@@ -1112,7 +1110,6 @@
/* This value must be overridden by the board. */
clock-frequency = <0>;
clock-output-names = "can_clk";
- status = "disabled";
};
/* Special CPG clocks */
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 07055ea..a691d59 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -63,6 +63,9 @@
CONFIG_TOUCHSCREEN_BU21013=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_AB8500_PONKEY=y
+CONFIG_RMI4_CORE=y
+CONFIG_RMI4_I2C=y
+CONFIG_RMI4_F11=y
# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_LEGACY_PTYS is not set
diff --git a/arch/arm/mach-omap1/id.c b/arch/arm/mach-omap1/id.c
index bfabc06..52de382 100644
--- a/arch/arm/mach-omap1/id.c
+++ b/arch/arm/mach-omap1/id.c
@@ -65,7 +65,6 @@
unsigned int omap_rev(void)
{
- WARN_ON_ONCE(!omap_revision || omap_revision == -1);
return omap_revision;
}
EXPORT_SYMBOL(omap_rev);
diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c
index b2f5668..2abd53a 100644
--- a/arch/arm/mach-omap2/id.c
+++ b/arch/arm/mach-omap2/id.c
@@ -46,7 +46,6 @@
unsigned int omap_rev(void)
{
- WARN_ON_ONCE(!omap_revision || omap_revision == -1);
return omap_revision;
}
EXPORT_SYMBOL(omap_rev);
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index 913a319..fffb697 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -1235,5 +1235,6 @@
void __init pxa2xx_set_dmac_info(int nb_channels, int nb_requestors)
{
pxa_dma_pdata.dma_channels = nb_channels;
+ pxa_dma_pdata.nb_requestors = nb_requestors;
pxa_register_device(&pxa2xx_pxa_dma, &pxa_dma_pdata);
}
diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig
index c6f6ed1..36e3c79 100644
--- a/arch/arm/mach-sa1100/Kconfig
+++ b/arch/arm/mach-sa1100/Kconfig
@@ -61,10 +61,7 @@
select MFD_IPAQ_MICRO
help
Say Y here if you intend to run this kernel on the Compaq iPAQ
- H3100 handheld computer. Information about this machine and the
- Linux port to this machine can be found at:
-
- <http://www.handhelds.org/Compaq/index.html#iPAQ_H3100>
+ H3100 handheld computer.
config SA1100_H3600
bool "Compaq iPAQ H3600/H3700"
@@ -73,10 +70,7 @@
select MFD_IPAQ_MICRO
help
Say Y here if you intend to run this kernel on the Compaq iPAQ
- H3600 handheld computer. Information about this machine and the
- Linux port to this machine can be found at:
-
- <http://www.handhelds.org/Compaq/index.html#iPAQ_H3600>
+ H3600 and H3700 handheld computers.
config SA1100_BADGE4
bool "HP Labs BadgePAD 4"
diff --git a/arch/arm/mach-shmobile/timer.c b/arch/arm/mach-shmobile/timer.c
index ad008e4..67d79f9 100644
--- a/arch/arm/mach-shmobile/timer.c
+++ b/arch/arm/mach-shmobile/timer.c
@@ -40,8 +40,7 @@
void __init shmobile_init_delay(void)
{
struct device_node *np, *cpus;
- bool is_a7_a8_a9 = false;
- bool is_a15 = false;
+ unsigned int div = 0;
bool has_arch_timer = false;
u32 max_freq = 0;
@@ -55,27 +54,22 @@
if (!of_property_read_u32(np, "clock-frequency", &freq))
max_freq = max(max_freq, freq);
- if (of_device_is_compatible(np, "arm,cortex-a8") ||
- of_device_is_compatible(np, "arm,cortex-a9")) {
- is_a7_a8_a9 = true;
- } else if (of_device_is_compatible(np, "arm,cortex-a7")) {
- is_a7_a8_a9 = true;
- has_arch_timer = true;
- } else if (of_device_is_compatible(np, "arm,cortex-a15")) {
- is_a15 = true;
+ if (of_device_is_compatible(np, "arm,cortex-a8")) {
+ div = 2;
+ } else if (of_device_is_compatible(np, "arm,cortex-a9")) {
+ div = 1;
+ } else if (of_device_is_compatible(np, "arm,cortex-a7") ||
+ of_device_is_compatible(np, "arm,cortex-a15")) {
+ div = 1;
has_arch_timer = true;
}
}
of_node_put(cpus);
- if (!max_freq)
+ if (!max_freq || !div)
return;
- if (!has_arch_timer || !IS_ENABLED(CONFIG_ARM_ARCH_TIMER)) {
- if (is_a7_a8_a9)
- shmobile_setup_delay_hz(max_freq, 1, 3);
- else if (is_a15)
- shmobile_setup_delay_hz(max_freq, 2, 4);
- }
+ if (!has_arch_timer || !IS_ENABLED(CONFIG_ARM_ARCH_TIMER))
+ shmobile_setup_delay_hz(max_freq, 1, div);
}
diff --git a/arch/arm/mach-uniphier/platsmp.c b/arch/arm/mach-uniphier/platsmp.c
index 6914135..db04142 100644
--- a/arch/arm/mach-uniphier/platsmp.c
+++ b/arch/arm/mach-uniphier/platsmp.c
@@ -120,7 +120,7 @@
if (ret)
return ret;
- uniphier_smp_rom_boot_rsv2 = ioremap(rom_rsv2_phys, sizeof(SZ_4));
+ uniphier_smp_rom_boot_rsv2 = ioremap(rom_rsv2_phys, SZ_4);
if (!uniphier_smp_rom_boot_rsv2) {
pr_err("failed to map ROM_BOOT_RSV2 register\n");
return -ENOMEM;
diff --git a/arch/arm64/boot/dts/broadcom/vulcan.dtsi b/arch/arm64/boot/dts/broadcom/vulcan.dtsi
index c49b5a8..85820e2 100644
--- a/arch/arm64/boot/dts/broadcom/vulcan.dtsi
+++ b/arch/arm64/boot/dts/broadcom/vulcan.dtsi
@@ -108,12 +108,15 @@
reg = <0x0 0x30000000 0x0 0x10000000>;
reg-names = "PCI ECAM";
- /* IO 0x4000_0000 - 0x4001_0000 */
- ranges = <0x01000000 0 0x40000000 0 0x40000000 0 0x00010000
- /* MEM 0x4800_0000 - 0x5000_0000 */
- 0x02000000 0 0x48000000 0 0x48000000 0 0x08000000
- /* MEM64 pref 0x6_0000_0000 - 0x7_0000_0000 */
- 0x43000000 6 0x00000000 6 0x00000000 1 0x00000000>;
+ /*
+ * PCI ranges:
+ * IO no supported
+ * MEM 0x4000_0000 - 0x6000_0000
+ * MEM64 pref 0x40_0000_0000 - 0x60_0000_0000
+ */
+ ranges =
+ <0x02000000 0 0x40000000 0 0x40000000 0 0x20000000
+ 0x43000000 0x40 0x00000000 0x40 0x00000000 0x20 0x00000000>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map =
/* addr pin ic icaddr icintr */
diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c
index c2e5286..ce54a01 100644
--- a/drivers/bus/mvebu-mbus.c
+++ b/drivers/bus/mvebu-mbus.c
@@ -972,7 +972,7 @@
}
}
- pr_err("invalid dram address 0x%x\n", phyaddr);
+ pr_err("invalid dram address %pa\n", &phyaddr);
return -EINVAL;
}
EXPORT_SYMBOL_GPL(mvebu_mbus_get_dram_win_info);
diff --git a/drivers/bus/uniphier-system-bus.c b/drivers/bus/uniphier-system-bus.c
index 834a2ae..350b730 100644
--- a/drivers/bus/uniphier-system-bus.c
+++ b/drivers/bus/uniphier-system-bus.c
@@ -108,7 +108,7 @@
for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
for (j = i + 1; j < ARRAY_SIZE(priv->bank); j++) {
- if (priv->bank[i].end > priv->bank[j].base ||
+ if (priv->bank[i].end > priv->bank[j].base &&
priv->bank[i].base < priv->bank[j].end) {
dev_err(priv->dev,
"region overlap between bank%d and bank%d\n",
diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
index 57e781c..837effe 100644
--- a/drivers/soc/mediatek/mtk-scpsys.c
+++ b/drivers/soc/mediatek/mtk-scpsys.c
@@ -491,13 +491,14 @@
genpd->dev_ops.active_wakeup = scpsys_active_wakeup;
/*
- * With CONFIG_PM disabled turn on all domains to make the
- * hardware usable.
+ * Initially turn on all domains to make the domains usable
+ * with !CONFIG_PM and to get the hardware in sync with the
+ * software. The unused domains will be switched off during
+ * late_init time.
*/
- if (!IS_ENABLED(CONFIG_PM))
- genpd->power_on(genpd);
+ genpd->power_on(genpd);
- pm_genpd_init(genpd, NULL, true);
+ pm_genpd_init(genpd, NULL, false);
}
/*