HID: new driver for PicoLCD device

Add basic driver for PicoLCD graphics device.
Initially support keypad with input device and provide support
for debugging communication via events file from debugfs.

Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-picolcd b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
new file mode 100644
index 0000000..6fb4f21
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
@@ -0,0 +1,17 @@
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to switch the PicoLCD device between LCD
+		(firmware) and bootloader (flasher) operation modes.
+
+		Reading: returns list of available modes, the active mode being
+		enclosed in brackets ('[' and ']')
+
+		Writing: causes operation mode switch. Permitted values are
+		the non-active mode names listed when read, optionally followed
+		by a delay value expressed in ms.
+
+		Note: when switching mode the current PicoLCD HID device gets
+		disconnected and reconnects after above delay (default value
+		is 5 seconds though this default should not be relied on).
+
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 71d4c07..138ba6a 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -262,6 +262,24 @@
 	---help---
 	Support for Petalynx Maxter remote control.
 
+config HID_PICOLCD
+	tristate "PicoLCD (graphic version)"
+	depends on USB_HID
+	---help---
+	  This provides support for Minibox PicoLCD devices, currently
+	  only the graphical ones are supported.
+
+	  This includes support for the following device features:
+	  - Keypad
+	  - Switching between Firmware and Flash mode
+	  Features that are not (yet) supported:
+	  - Framebuffer for monochrome 256x64 display
+	  - Backlight control
+	  - Contrast control
+	  - IR
+	  - General purpose outputs
+	  - EEProm / Flash access
+
 config HID_QUANTA
 	tristate "Quanta Optical Touch"
 	depends on USB_HID
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index 0b2618f..7fd1614 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -44,6 +44,7 @@
 obj-$(CONFIG_HID_QUANTA)	+= hid-quanta.o
 obj-$(CONFIG_HID_PANTHERLORD)	+= hid-pl.o
 obj-$(CONFIG_HID_PETALYNX)	+= hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD)	+= hid-picolcd.o
 obj-$(CONFIG_HID_SAMSUNG)	+= hid-samsung.o
 obj-$(CONFIG_HID_SMARTJOYPLUS)	+= hid-sjoy.o
 obj-$(CONFIG_HID_SONY)		+= hid-sony.o
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index 2e2aa75..bb11fb4 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -1335,6 +1335,8 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index 797e064..783b41d 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -341,6 +341,8 @@
 #define USB_VENDOR_ID_MICROCHIP		0x04d8
 #define USB_DEVICE_ID_PICKIT1		0x0032
 #define USB_DEVICE_ID_PICKIT2		0x0033
+#define USB_DEVICE_ID_PICOLCD		0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER	0xf002
 
 #define USB_VENDOR_ID_MICROSOFT		0x045e
 #define USB_DEVICE_ID_SIDEWINDER_GV	0x003b
diff --git a/drivers/hid/hid-picolcd.c b/drivers/hid/hid-picolcd.c
new file mode 100644
index 0000000..c7855f3
--- /dev/null
+++ b/drivers/hid/hid-picolcd.c
@@ -0,0 +1,1183 @@
+/***************************************************************************
+ *   Copyright (C) 2010 by Bruno Prémont <bonbons@linux-vserver.org>       *
+ *                                                                         *
+ *   Based on Logitech G13 driver (v0.4)                                   *
+ *     Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu>   *
+ *                                                                         *
+ *   This program is free software: you can redistribute it and/or modify  *
+ *   it under the terms of the GNU General Public License as published by  *
+ *   the Free Software Foundation, version 2 of the License.               *
+ *                                                                         *
+ *   This driver is distributed in the hope that it will be useful, but    *
+ *   WITHOUT ANY WARRANTY; without even the implied warranty of            *
+ *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU      *
+ *   General Public License for more details.                              *
+ *                                                                         *
+ *   You should have received a copy of the GNU General Public License     *
+ *   along with this software. If not see <http://www.gnu.org/licenses/>.  *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+
+#define PICOLCD_NAME "PicoLCD (graphic)"
+
+/* Report numbers */
+#define REPORT_ERROR_CODE      0x10 /* LCD: IN[16]  */
+#define   ERR_SUCCESS            0x00
+#define   ERR_PARAMETER_MISSING  0x01
+#define   ERR_DATA_MISSING       0x02
+#define   ERR_BLOCK_READ_ONLY    0x03
+#define   ERR_BLOCK_NOT_ERASABLE 0x04
+#define   ERR_BLOCK_TOO_BIG      0x05
+#define   ERR_SECTION_OVERFLOW   0x06
+#define   ERR_INVALID_CMD_LEN    0x07
+#define   ERR_INVALID_DATA_LEN   0x08
+#define REPORT_KEY_STATE       0x11 /* LCD: IN[2]   */
+#define REPORT_IR_DATA         0x21 /* LCD: IN[63]  */
+#define REPORT_EE_DATA         0x32 /* LCD: IN[63]  */
+#define REPORT_MEMORY          0x41 /* LCD: IN[63]  */
+#define REPORT_LED_STATE       0x81 /* LCD: OUT[1]  */
+#define REPORT_BRIGHTNESS      0x91 /* LCD: OUT[1]  */
+#define REPORT_CONTRAST        0x92 /* LCD: OUT[1]  */
+#define REPORT_RESET           0x93 /* LCD: OUT[2]  */
+#define REPORT_LCD_CMD         0x94 /* LCD: OUT[63] */
+#define REPORT_LCD_DATA        0x95 /* LCD: OUT[63] */
+#define REPORT_LCD_CMD_DATA    0x96 /* LCD: OUT[63] */
+#define	REPORT_EE_READ         0xa3 /* LCD: OUT[63] */
+#define REPORT_EE_WRITE        0xa4 /* LCD: OUT[63] */
+#define REPORT_ERASE_MEMORY    0xb2 /* LCD: OUT[2]  */
+#define REPORT_READ_MEMORY     0xb3 /* LCD: OUT[3]  */
+#define REPORT_WRITE_MEMORY    0xb4 /* LCD: OUT[63] */
+#define REPORT_SPLASH_RESTART  0xc1 /* LCD: OUT[1]  */
+#define REPORT_EXIT_KEYBOARD   0xef /* LCD: OUT[2]  */
+#define REPORT_VERSION         0xf1 /* LCD: IN[2],OUT[1]    Bootloader: IN[2],OUT[1]   */
+#define REPORT_BL_ERASE_MEMORY 0xf2 /*                      Bootloader: IN[36],OUT[4]  */
+#define REPORT_BL_READ_MEMORY  0xf3 /*                      Bootloader: IN[36],OUT[4]  */
+#define REPORT_BL_WRITE_MEMORY 0xf4 /*                      Bootloader: IN[36],OUT[36] */
+#define REPORT_DEVID           0xf5 /* LCD: IN[5], OUT[1]   Bootloader: IN[5],OUT[1]   */
+#define REPORT_SPLASH_SIZE     0xf6 /* LCD: IN[4], OUT[1]   */
+#define REPORT_HOOK_VERSION    0xf7 /* LCD: IN[2], OUT[1]   */
+#define REPORT_EXIT_FLASHER    0xff /*                      Bootloader: OUT[2]         */
+
+/* Input device
+ *
+ * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys
+ * and header for 4x4 key matrix. The built-in keys are part of the matrix.
+ */
+static const unsigned short def_keymap[] = {
+	KEY_RESERVED,	/* none */
+	KEY_BACK,	/* col 4 + row 1 */
+	KEY_HOMEPAGE,	/* col 3 + row 1 */
+	KEY_RESERVED,	/* col 2 + row 1 */
+	KEY_RESERVED,	/* col 1 + row 1 */
+	KEY_SCROLLUP,	/* col 4 + row 2 */
+	KEY_OK,		/* col 3 + row 2 */
+	KEY_SCROLLDOWN,	/* col 2 + row 2 */
+	KEY_RESERVED,	/* col 1 + row 2 */
+	KEY_RESERVED,	/* col 4 + row 3 */
+	KEY_RESERVED,	/* col 3 + row 3 */
+	KEY_RESERVED,	/* col 2 + row 3 */
+	KEY_RESERVED,	/* col 1 + row 3 */
+	KEY_RESERVED,	/* col 4 + row 4 */
+	KEY_RESERVED,	/* col 3 + row 4 */
+	KEY_RESERVED,	/* col 2 + row 4 */
+	KEY_RESERVED,	/* col 1 + row 4 */
+};
+#define PICOLCD_KEYS ARRAY_SIZE(def_keymap)
+
+/* Description of in-progress IO operation, used for operations
+ * that trigger response from device */
+struct picolcd_pending {
+	struct hid_report *out_report;
+	struct hid_report *in_report;
+	struct completion ready;
+	int raw_size;
+	u8 raw_data[64];
+};
+
+/* Per device data structure */
+struct picolcd_data {
+	struct hid_device *hdev;
+#ifdef CONFIG_DEBUG_FS
+	int addr_sz;
+#endif
+	u8 version[2];
+	/* input stuff */
+	u8 pressed_keys[2];
+	struct input_dev *input_keys;
+	struct input_dev *input_cir;
+	unsigned short keycode[PICOLCD_KEYS];
+
+	/* Housekeeping stuff */
+	spinlock_t lock;
+	struct mutex mutex;
+	struct picolcd_pending *pending;
+	int status;
+#define PICOLCD_BOOTLOADER 1
+#define PICOLCD_FAILED 2
+};
+
+
+/* Find a given report */
+#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT)
+#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT)
+
+static struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir)
+{
+	struct list_head *feature_report_list = &hdev->report_enum[dir].report_list;
+	struct hid_report *report = NULL;
+
+	list_for_each_entry(report, feature_report_list, list) {
+		if (report->id == id)
+			return report;
+	}
+	dev_warn(&hdev->dev, "No report with id 0x%x found\n", id);
+	return NULL;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void picolcd_debug_out_report(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report);
+#define usbhid_submit_report(a, b, c) \
+	do { \
+		picolcd_debug_out_report(hid_get_drvdata(a), a, b); \
+		usbhid_submit_report(a, b, c); \
+	} while (0)
+#endif
+
+/* Submit a report and wait for a reply from device - if device fades away
+ * or does not respond in time, return NULL */
+static struct picolcd_pending *picolcd_send_and_wait(struct hid_device *hdev,
+		int report_id, const u8 *raw_data, int size)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct picolcd_pending *work;
+	struct hid_report *report = picolcd_out_report(report_id, hdev);
+	unsigned long flags;
+	int i, j, k;
+
+	if (!report || !data)
+		return NULL;
+	if (data->status & PICOLCD_FAILED)
+		return NULL;
+	work = kzalloc(sizeof(*work), GFP_KERNEL);
+	if (!work)
+		return NULL;
+
+	init_completion(&work->ready);
+	work->out_report = report;
+	work->in_report  = NULL;
+	work->raw_size   = 0;
+
+	mutex_lock(&data->mutex);
+	spin_lock_irqsave(&data->lock, flags);
+	for (i = k = 0; i < report->maxfield; i++)
+		for (j = 0; j < report->field[i]->report_count; j++) {
+			hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0);
+			k++;
+		}
+	data->pending = work;
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	wait_for_completion_interruptible_timeout(&work->ready, HZ*2);
+	spin_lock_irqsave(&data->lock, flags);
+	data->pending = NULL;
+	spin_unlock_irqrestore(&data->lock, flags);
+	mutex_unlock(&data->mutex);
+	return work;
+}
+
+/*
+ * input class device
+ */
+static int picolcd_raw_keypad(struct picolcd_data *data,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	/*
+	 * Keypad event
+	 * First and second data bytes list currently pressed keys,
+	 * 0x00 means no key and at most 2 keys may be pressed at same time
+	 */
+	int i, j;
+
+	/* determine newly pressed keys */
+	for (i = 0; i < size; i++) {
+		unsigned int key_code;
+		if (raw_data[i] == 0)
+			continue;
+		for (j = 0; j < sizeof(data->pressed_keys); j++)
+			if (data->pressed_keys[j] == raw_data[i])
+				goto key_already_down;
+		for (j = 0; j < sizeof(data->pressed_keys); j++)
+			if (data->pressed_keys[j] == 0) {
+				data->pressed_keys[j] = raw_data[i];
+				break;
+			}
+		input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]);
+		if (raw_data[i] < PICOLCD_KEYS)
+			key_code = data->keycode[raw_data[i]];
+		else
+			key_code = KEY_UNKNOWN;
+		if (key_code != KEY_UNKNOWN) {
+			dbg_hid(PICOLCD_NAME " got key press for %u:%d",
+					raw_data[i], key_code);
+			input_report_key(data->input_keys, key_code, 1);
+		}
+		input_sync(data->input_keys);
+key_already_down:
+		continue;
+	}
+
+	/* determine newly released keys */
+	for (j = 0; j < sizeof(data->pressed_keys); j++) {
+		unsigned int key_code;
+		if (data->pressed_keys[j] == 0)
+			continue;
+		for (i = 0; i < size; i++)
+			if (data->pressed_keys[j] == raw_data[i])
+				goto key_still_down;
+		input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]);
+		if (data->pressed_keys[j] < PICOLCD_KEYS)
+			key_code = data->keycode[data->pressed_keys[j]];
+		else
+			key_code = KEY_UNKNOWN;
+		if (key_code != KEY_UNKNOWN) {
+			dbg_hid(PICOLCD_NAME " got key release for %u:%d",
+					data->pressed_keys[j], key_code);
+			input_report_key(data->input_keys, key_code, 0);
+		}
+		input_sync(data->input_keys);
+		data->pressed_keys[j] = 0;
+key_still_down:
+		continue;
+	}
+	return 1;
+}
+
+static int picolcd_raw_cir(struct picolcd_data *data,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	/* Need understanding of CIR data format to implement ... */
+	return 1;
+}
+
+static int picolcd_check_version(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct picolcd_pending *verinfo;
+	int ret = 0;
+
+	if (!data)
+		return -ENODEV;
+
+	verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+	if (!verinfo) {
+		dev_err(&hdev->dev, "no version response from PicoLCD");
+		return -ENODEV;
+	}
+
+	if (verinfo->raw_size == 2) {
+		if (data->status & PICOLCD_BOOTLOADER) {
+			dev_info(&hdev->dev, "PicoLCD, bootloader version %d.%d\n",
+					verinfo->raw_data[0], verinfo->raw_data[1]);
+			data->version[0] = verinfo->raw_data[0];
+			data->version[1] = verinfo->raw_data[1];
+		} else {
+			dev_info(&hdev->dev, "PicoLCD, firmware version %d.%d\n",
+					verinfo->raw_data[1], verinfo->raw_data[0]);
+			data->version[0] = verinfo->raw_data[1];
+			data->version[1] = verinfo->raw_data[0];
+		}
+	} else {
+		dev_err(&hdev->dev, "confused, got unexpected version response from PicoLCD\n");
+		ret = -EINVAL;
+	}
+	kfree(verinfo);
+	return ret;
+}
+
+/*
+ * Reset our device and wait for answer to VERSION request
+ */
+static int picolcd_reset(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev);
+	unsigned long flags;
+
+	if (!data || !report || report->maxfield != 1)
+		return -ENODEV;
+
+	spin_lock_irqsave(&data->lock, flags);
+	if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+		data->status |= PICOLCD_BOOTLOADER;
+
+	/* perform the reset */
+	hid_set_field(report->field[0], 0, 1);
+	usbhid_submit_report(hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	return picolcd_check_version(hdev);
+}
+
+/*
+ * The "operation_mode" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+
+	if (data->status & PICOLCD_BOOTLOADER)
+		return snprintf(buf, PAGE_SIZE, "[bootloader] lcd\n");
+	else
+		return snprintf(buf, PAGE_SIZE, "bootloader [lcd]\n");
+}
+
+static ssize_t picolcd_operation_mode_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+	struct hid_report *report = NULL;
+	size_t cnt = count;
+	int timeout = 5000;
+	unsigned u;
+	unsigned long flags;
+
+	if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) {
+		if (data->status & PICOLCD_BOOTLOADER)
+			report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev);
+		buf += 3;
+		cnt -= 3;
+	} else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) {
+		if (!(data->status & PICOLCD_BOOTLOADER))
+			report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev);
+		buf += 10;
+		cnt -= 10;
+	}
+	if (!report)
+		return -EINVAL;
+
+	while (cnt > 0 && (*buf == ' ' || *buf == '\t')) {
+		buf++;
+		cnt--;
+	}
+	while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r'))
+		cnt--;
+	if (cnt > 0) {
+		if (sscanf(buf, "%u", &u) != 1)
+			return -EINVAL;
+		if (u > 30000)
+			return -EINVAL;
+		else
+			timeout = u;
+	}
+
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report->field[0], 0, timeout & 0xff);
+	hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff);
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	return count;
+}
+
+static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show,
+		picolcd_operation_mode_store);
+
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * Helper code for HID report level dumping/debugging
+ */
+static const char *error_codes[] = {
+	"success", "parameter missing", "data_missing", "block readonly",
+	"block not erasable", "block too big", "section overflow",
+	"invalid command length", "invalid data length",
+};
+
+static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data,
+		const size_t data_len)
+{
+	int i, j;
+	for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) {
+		dst[j++] = hex_asc[(data[i] >> 4) & 0x0f];
+		dst[j++] = hex_asc[data[i] & 0x0f];
+		dst[j++] = ' ';
+	}
+	if (j < dst_sz) {
+		dst[j--] = '\0';
+		dst[j] = '\n';
+	} else
+		dst[j] = '\0';
+}
+
+static void picolcd_debug_out_report(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report)
+{
+	u8 raw_data[70];
+	int raw_size = (report->size >> 3) + 1;
+	char *buff;
+#define BUFF_SZ 256
+
+	/* Avoid unnecessary overhead if debugfs is disabled */
+	if (!hdev->debug_events)
+		return;
+
+	buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+	if (!buff)
+		return;
+
+	snprintf(buff, BUFF_SZ, "\nout report %d (size %d) =  ",
+			report->id, raw_size);
+	hid_debug_event(hdev, buff);
+	if (raw_size + 5 > sizeof(raw_data)) {
+		hid_debug_event(hdev, " TOO BIG\n");
+		return;
+	} else {
+		raw_data[0] = report->id;
+		hid_output_report(report, raw_data);
+		dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size);
+		hid_debug_event(hdev, buff);
+	}
+
+	switch (report->id) {
+	case REPORT_LED_STATE:
+		/* 1 data byte with GPO state */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LED_STATE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_BRIGHTNESS:
+		/* 1 data byte with brightness */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_BRIGHTNESS", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_CONTRAST:
+		/* 1 data byte with contrast */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_CONTRAST", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_RESET:
+		/* 2 data bytes with reset duration in ms */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_RESET", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n",
+				raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_LCD_CMD:
+		/* 63 data bytes with LCD commands */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO: format decoding */
+		break;
+	case REPORT_LCD_DATA:
+		/* 63 data bytes with LCD data */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		/* TODO: format decoding */
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_LCD_CMD_DATA:
+		/* 63 data bytes with LCD commands and data */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		/* TODO: format decoding */
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EE_READ:
+		/* 3 data bytes with read area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EE_READ", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EE_WRITE:
+		/* 3+1..20 data bytes with write area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EE_WRITE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		if (raw_data[3] == 0) {
+			snprintf(buff, BUFF_SZ, "\tNo data\n");
+		} else if (raw_data[3] + 4 <= raw_size) {
+			snprintf(buff, BUFF_SZ, "\tData: ");
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_ERASE_MEMORY:
+	case REPORT_BL_ERASE_MEMORY:
+		/* 3 data bytes with pointer inside erase block */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_ERASE_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_READ_MEMORY:
+	case REPORT_BL_READ_MEMORY:
+		/* 4 data bytes with read area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_READ_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_WRITE_MEMORY:
+	case REPORT_BL_WRITE_MEMORY:
+		/* 4+1..32 data bytes with write adrea description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_WRITE_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[3] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[3] + 4 <= raw_size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[4] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[4] + 5 <= raw_size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_RESTART:
+		/* TODO */
+		break;
+	case REPORT_EXIT_KEYBOARD:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EXIT_KEYBOARD", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+				raw_data[1] | (raw_data[2] << 8),
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_VERSION:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_DEVID:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_DEVID", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_SIZE:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_SPLASH_SIZE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_HOOK_VERSION:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_HOOK_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EXIT_FLASHER:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+				raw_data[1] | (raw_data[2] << 8),
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	default:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"<unknown>", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	}
+	wake_up_interruptible(&hdev->debug_wait);
+	kfree(buff);
+}
+
+static void picolcd_debug_raw_event(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report,
+		u8 *raw_data, int size)
+{
+	char *buff;
+
+#define BUFF_SZ 256
+	/* Avoid unnecessary overhead if debugfs is disabled */
+	if (!hdev->debug_events)
+		return;
+
+	buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+	if (!buff)
+		return;
+
+	switch (report->id) {
+	case REPORT_ERROR_CODE:
+		/* 2 data bytes with affected report and error code */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_ERROR_CODE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[2] < ARRAY_SIZE(error_codes))
+			snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n",
+					raw_data[2], error_codes[raw_data[2]], raw_data[1]);
+		else
+			snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n",
+					raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_KEY_STATE:
+		/* 2 data bytes with key state */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_KEY_STATE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[1] == 0)
+			snprintf(buff, BUFF_SZ, "\tNo key pressed\n");
+		else if (raw_data[2] == 0)
+			snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n",
+					raw_data[1], raw_data[1]);
+		else
+			snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n",
+					raw_data[1], raw_data[1], raw_data[2], raw_data[2]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_IR_DATA:
+		/* Up to 20 byes of IR scancode data */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_IR_DATA", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[1] == 0) {
+			snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n");
+			hid_debug_event(hdev, buff);
+		} else if (raw_data[1] + 1 <= size) {
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ",
+					raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n",
+					raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+		}
+		break;
+	case REPORT_EE_DATA:
+		/* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_EE_DATA", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		if (raw_data[3] == 0) {
+			snprintf(buff, BUFF_SZ, "\tNo data\n");
+			hid_debug_event(hdev, buff);
+		} else if (raw_data[3] + 4 <= size) {
+			snprintf(buff, BUFF_SZ, "\tData: ");
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			hid_debug_event(hdev, buff);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			hid_debug_event(hdev, buff);
+		}
+		break;
+	case REPORT_MEMORY:
+		/* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[3] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[3] + 4 <= size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[4] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[4] + 5 <= size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_VERSION:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_BL_ERASE_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_ERASE_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_BL_READ_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_READ_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_BL_WRITE_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_WRITE_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_DEVID:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_DEVID", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n",
+				raw_data[1], raw_data[2], raw_data[3], raw_data[4]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n",
+				raw_data[5]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_SIZE:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_SPLASH_SIZE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n",
+				(raw_data[2] << 8) | raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n",
+				(raw_data[4] << 8) | raw_data[3]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_HOOK_VERSION:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_HOOK_VERSION", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+				raw_data[1], raw_data[2]);
+		hid_debug_event(hdev, buff);
+		break;
+	default:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"<unknown>", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	}
+	wake_up_interruptible(&hdev->debug_wait);
+	kfree(buff);
+}
+#else
+#define picolcd_debug_raw_event(data, hdev, report, raw_data, size)
+#endif
+
+/*
+ * Handle raw report as sent by device
+ */
+static int picolcd_raw_event(struct hid_device *hdev,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	unsigned long flags;
+	int ret = 0;
+
+	if (!data)
+		return 1;
+
+	if (report->id == REPORT_KEY_STATE) {
+		if (data->input_keys)
+			ret = picolcd_raw_keypad(data, report, raw_data+1, size-1);
+	} else if (report->id == REPORT_IR_DATA) {
+		if (data->input_cir)
+			ret = picolcd_raw_cir(data, report, raw_data+1, size-1);
+	} else {
+		spin_lock_irqsave(&data->lock, flags);
+		/*
+		 * We let the caller of picolcd_send_and_wait() check if the
+		 * report we got is one of the expected ones or not.
+		 */
+		if (data->pending) {
+			memcpy(data->pending->raw_data, raw_data+1, size-1);
+			data->pending->raw_size  = size-1;
+			data->pending->in_report = report;
+			complete(&data->pending->ready);
+		}
+		spin_unlock_irqrestore(&data->lock, flags);
+	}
+
+	picolcd_debug_raw_event(data, hdev, report, raw_data, size);
+	return 1;
+}
+
+/* initialize keypad input device */
+static int picolcd_init_keys(struct picolcd_data *data,
+		struct hid_report *report)
+{
+	struct hid_device *hdev = data->hdev;
+	struct input_dev *idev;
+	int error, i;
+
+	if (!report)
+		return -ENODEV;
+	if (report->maxfield != 1 || report->field[0]->report_count != 2 ||
+			report->field[0]->report_size != 8) {
+		dev_err(&hdev->dev, "unsupported KEY_STATE report");
+		return -EINVAL;
+	}
+
+	idev = input_allocate_device();
+	if (idev == NULL) {
+		dev_err(&hdev->dev, "failed to allocate input device");
+		return -ENOMEM;
+	}
+	input_set_drvdata(idev, hdev);
+	memcpy(data->keycode, def_keymap, sizeof(def_keymap));
+	idev->name = hdev->name;
+	idev->phys = hdev->phys;
+	idev->uniq = hdev->uniq;
+	idev->id.bustype = hdev->bus;
+	idev->id.vendor  = hdev->vendor;
+	idev->id.product = hdev->product;
+	idev->id.version = hdev->version;
+	idev->dev.parent = hdev->dev.parent;
+	idev->keycode     = &data->keycode;
+	idev->keycodemax  = PICOLCD_KEYS;
+	idev->keycodesize = sizeof(data->keycode[0]);
+	input_set_capability(idev, EV_MSC, MSC_SCAN);
+	set_bit(EV_REP, idev->evbit);
+	for (i = 0; i < PICOLCD_KEYS; i++)
+		input_set_capability(idev, EV_KEY, data->keycode[i]);
+	error = input_register_device(idev);
+	if (error) {
+		dev_err(&hdev->dev, "error registering the input device");
+		input_free_device(idev);
+		return error;
+	}
+	data->input_keys = idev;
+	return 0;
+}
+
+static void picolcd_exit_keys(struct picolcd_data *data)
+{
+	struct input_dev *idev = data->input_keys;
+
+	data->input_keys = NULL;
+	if (idev)
+		input_unregister_device(idev);
+}
+
+/* initialize CIR input device */
+static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+	/* support not implemented yet */
+	return 0;
+}
+
+static inline void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+
+static int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data)
+{
+	struct hid_report *report;
+	int error;
+
+	error = picolcd_check_version(hdev);
+	if (error)
+		return error;
+
+	if (data->version[0] != 0 && data->version[1] != 3)
+		dev_info(&hdev->dev, "Device with untested firmware revision, "
+				"please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+				dev_name(&hdev->dev));
+
+	/* Setup keypad input device */
+	error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev));
+	if (error)
+		goto err;
+
+	/* Setup CIR input device */
+	error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev));
+	if (error)
+		goto err;
+
+#ifdef CONFIG_DEBUG_FS
+	report = picolcd_out_report(REPORT_READ_MEMORY, hdev);
+	if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+		data->addr_sz = report->field[0]->report_count - 1;
+	else
+		data->addr_sz = -1;
+#endif
+	return 0;
+err:
+	picolcd_exit_cir(data);
+	picolcd_exit_keys(data);
+	return error;
+}
+
+static int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data)
+{
+	struct hid_report *report;
+	int error;
+
+	error = picolcd_check_version(hdev);
+	if (error)
+		return error;
+
+	if (data->version[0] != 1 && data->version[1] != 0)
+		dev_info(&hdev->dev, "Device with untested bootloader revision, "
+				"please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+				dev_name(&hdev->dev));
+
+#ifdef CONFIG_DEBUG_FS
+	report = picolcd_out_report(REPORT_BL_READ_MEMORY, hdev);
+	if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+		data->addr_sz = report->field[0]->report_count - 1;
+	else
+		data->addr_sz = -1;
+#endif
+	return 0;
+}
+
+static int picolcd_probe(struct hid_device *hdev,
+		     const struct hid_device_id *id)
+{
+	struct picolcd_data *data;
+	int error = -ENOMEM;
+
+	dbg_hid(PICOLCD_NAME " hardware probe...\n");
+
+	/*
+	 * Let's allocate the picolcd data structure, set some reasonable
+	 * defaults, and associate it with the device
+	 */
+	data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL);
+	if (data == NULL) {
+		dev_err(&hdev->dev, "can't allocate space for Minibox PicoLCD device data\n");
+		error = -ENOMEM;
+		goto err_no_cleanup;
+	}
+
+	spin_lock_init(&data->lock);
+	mutex_init(&data->mutex);
+	data->hdev = hdev;
+	if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+		data->status |= PICOLCD_BOOTLOADER;
+	hid_set_drvdata(hdev, data);
+
+	/* Parse the device reports and start it up */
+	error = hid_parse(hdev);
+	if (error) {
+		dev_err(&hdev->dev, "device report parse failed\n");
+		goto err_cleanup_data;
+	}
+
+	/* We don't use hidinput but hid_hw_start() fails if nothing is
+	 * claimed. So spoof claimed input. */
+	hdev->claimed = HID_CLAIMED_INPUT;
+	error = hid_hw_start(hdev, 0);
+	hdev->claimed = 0;
+	if (error) {
+		dev_err(&hdev->dev, "hardware start failed\n");
+		goto err_cleanup_data;
+	}
+
+	error = hdev->ll_driver->open(hdev);
+	if (error) {
+		dev_err(&hdev->dev, "failed to open input interrupt pipe for key and IR events\n");
+		goto err_cleanup_hid_hw;
+	}
+
+	error = device_create_file(&hdev->dev, &dev_attr_operation_mode);
+	if (error) {
+		dev_err(&hdev->dev, "failed to create sysfs attributes\n");
+		goto err_cleanup_hid_ll;
+	}
+
+	if (data->status & PICOLCD_BOOTLOADER)
+		error = picolcd_probe_bootloader(hdev, data);
+	else
+		error = picolcd_probe_lcd(hdev, data);
+	if (error)
+		goto err_cleanup_sysfs;
+
+	dbg_hid(PICOLCD_NAME " activated and initialized\n");
+	return 0;
+
+err_cleanup_sysfs:
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+err_cleanup_hid_ll:
+	hdev->ll_driver->close(hdev);
+err_cleanup_hid_hw:
+	hid_hw_stop(hdev);
+err_cleanup_data:
+	kfree(data);
+err_no_cleanup:
+	hid_set_drvdata(hdev, NULL);
+
+	return error;
+}
+
+static void picolcd_remove(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	unsigned long flags;
+
+	dbg_hid(PICOLCD_NAME " hardware remove...\n");
+	spin_lock_irqsave(&data->lock, flags);
+	data->status |= PICOLCD_FAILED;
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+	hdev->ll_driver->close(hdev);
+	hid_hw_stop(hdev);
+	hid_set_drvdata(hdev, NULL);
+
+	/* Shortcut potential pending reply that will never arrive */
+	spin_lock_irqsave(&data->lock, flags);
+	if (data->pending)
+		complete(&data->pending->ready);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	/* Cleanup input */
+	picolcd_exit_cir(data);
+	picolcd_exit_keys(data);
+
+	mutex_destroy(&data->mutex);
+	/* Finally, clean up the picolcd data itself */
+	kfree(data);
+}
+
+static const struct hid_device_id picolcd_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, picolcd_devices);
+
+static struct hid_driver picolcd_driver = {
+	.name =          "hid-picolcd",
+	.id_table =      picolcd_devices,
+	.probe =         picolcd_probe,
+	.remove =        picolcd_remove,
+	.raw_event =     picolcd_raw_event,
+};
+
+static int __init picolcd_init(void)
+{
+	return hid_register_driver(&picolcd_driver);
+}
+
+static void __exit picolcd_exit(void)
+{
+	hid_unregister_driver(&picolcd_driver);
+}
+
+module_init(picolcd_init);
+module_exit(picolcd_exit);
+MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver");
+MODULE_LICENSE("GPL v2");