spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs
Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c
index 6cb2fdb..c8efa75 100644
--- a/drivers/spi/spi-topcliff-pch.c
+++ b/drivers/spi/spi-topcliff-pch.c
@@ -352,16 +352,26 @@
"%s returning due to suspend\n", __func__);
return IRQ_NONE;
}
- if (data->use_dma)
- return IRQ_NONE;
io_remap_addr = data->io_remap_addr;
spsr = io_remap_addr + PCH_SPSR;
reg_spsr_val = ioread32(spsr);
- if (reg_spsr_val & SPSR_ORF_BIT)
- dev_err(&board_dat->pdev->dev, "%s Over run error", __func__);
+ if (reg_spsr_val & SPSR_ORF_BIT) {
+ dev_err(&board_dat->pdev->dev, "%s Over run error\n", __func__);
+ if (data->current_msg->complete != 0) {
+ data->transfer_complete = true;
+ data->current_msg->status = -EIO;
+ data->current_msg->complete(data->current_msg->context);
+ data->bcurrent_msg_processing = false;
+ data->current_msg = NULL;
+ data->cur_trans = NULL;
+ }
+ }
+
+ if (data->use_dma)
+ return IRQ_NONE;
/* Check if the interrupt is for SPI device */
if (reg_spsr_val & (SPSR_FI_BIT | SPSR_RFI_BIT)) {
@@ -815,10 +825,11 @@
}
}
-static void pch_spi_start_transfer(struct pch_spi_data *data)
+static int pch_spi_start_transfer(struct pch_spi_data *data)
{
struct pch_spi_dma_ctrl *dma;
unsigned long flags;
+ int rtn;
dma = &data->dma;
@@ -833,7 +844,9 @@
initiating the transfer. */
dev_dbg(&data->master->dev,
"%s:waiting for transfer to get over\n", __func__);
- wait_event_interruptible(data->wait, data->transfer_complete);
+ rtn = wait_event_interruptible_timeout(data->wait,
+ data->transfer_complete,
+ msecs_to_jiffies(2 * HZ));
dma_sync_sg_for_cpu(&data->master->dev, dma->sg_rx_p, dma->nent,
DMA_FROM_DEVICE);
@@ -860,6 +873,8 @@
pch_spi_clear_fifo(data->master);
spin_unlock_irqrestore(&data->lock, flags);
+
+ return rtn;
}
static void pch_dma_rx_complete(void *arg)
@@ -1187,7 +1202,8 @@
if (data->use_dma) {
pch_spi_handle_dma(data, &bpw);
- pch_spi_start_transfer(data);
+ if (!pch_spi_start_transfer(data))
+ goto out;
pch_spi_copy_rx_data_for_dma(data, bpw);
} else {
pch_spi_set_tx(data, &bpw);
@@ -1225,6 +1241,7 @@
} while (data->cur_trans != NULL);
+out:
pch_spi_writereg(data->master, PCH_SSNXCR, SSN_HIGH);
if (data->use_dma)
pch_spi_release_dma(data);