| /* |
| * linux/arch/arm/mach-omap2/board-omap3evm.c |
| * |
| * Copyright (C) 2008 Texas Instruments |
| * |
| * Modified from mach-omap2/board-3430sdp.c |
| * |
| * Initial code: Syed Mohammed Khasim |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/gpio.h> |
| #include <linux/input.h> |
| #include <linux/input/matrix_keypad.h> |
| #include <linux/leds.h> |
| #include <linux/interrupt.h> |
| |
| #include <linux/spi/spi.h> |
| #include <linux/spi/ads7846.h> |
| #include <linux/i2c/twl.h> |
| #include <linux/usb/otg.h> |
| #include <linux/smsc911x.h> |
| |
| #include <linux/wl12xx.h> |
| #include <linux/regulator/fixed.h> |
| #include <linux/regulator/machine.h> |
| #include <linux/mmc/host.h> |
| |
| #include <mach/hardware.h> |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/map.h> |
| |
| #include <plat/board.h> |
| #include <plat/usb.h> |
| #include <plat/common.h> |
| #include <plat/mcspi.h> |
| #include <plat/display.h> |
| #include <plat/panel-generic-dpi.h> |
| |
| #include "mux.h" |
| #include "sdram-micron-mt46h32m32lf-6.h" |
| #include "hsmmc.h" |
| |
| #define OMAP3_EVM_TS_GPIO 175 |
| #define OMAP3_EVM_EHCI_VBUS 22 |
| #define OMAP3_EVM_EHCI_SELECT 61 |
| |
| #define OMAP3EVM_ETHR_START 0x2c000000 |
| #define OMAP3EVM_ETHR_SIZE 1024 |
| #define OMAP3EVM_ETHR_ID_REV 0x50 |
| #define OMAP3EVM_ETHR_GPIO_IRQ 176 |
| #define OMAP3EVM_SMSC911X_CS 5 |
| /* |
| * Eth Reset signal |
| * 64 = Generation 1 (<=RevD) |
| * 7 = Generation 2 (>=RevE) |
| */ |
| #define OMAP3EVM_GEN1_ETHR_GPIO_RST 64 |
| #define OMAP3EVM_GEN2_ETHR_GPIO_RST 7 |
| |
| static u8 omap3_evm_version; |
| |
| u8 get_omap3_evm_rev(void) |
| { |
| return omap3_evm_version; |
| } |
| EXPORT_SYMBOL(get_omap3_evm_rev); |
| |
| static void __init omap3_evm_get_revision(void) |
| { |
| void __iomem *ioaddr; |
| unsigned int smsc_id; |
| |
| /* Ethernet PHY ID is stored at ID_REV register */ |
| ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K); |
| if (!ioaddr) |
| return; |
| smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000; |
| iounmap(ioaddr); |
| |
| switch (smsc_id) { |
| /*SMSC9115 chipset*/ |
| case 0x01150000: |
| omap3_evm_version = OMAP3EVM_BOARD_GEN_1; |
| break; |
| /*SMSC 9220 chipset*/ |
| case 0x92200000: |
| default: |
| omap3_evm_version = OMAP3EVM_BOARD_GEN_2; |
| } |
| } |
| |
| #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) |
| static struct resource omap3evm_smsc911x_resources[] = { |
| [0] = { |
| .start = OMAP3EVM_ETHR_START, |
| .end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1), |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), |
| .end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), |
| .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW), |
| }, |
| }; |
| |
| static struct smsc911x_platform_config smsc911x_config = { |
| .phy_interface = PHY_INTERFACE_MODE_MII, |
| .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
| .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS), |
| }; |
| |
| static struct platform_device omap3evm_smsc911x_device = { |
| .name = "smsc911x", |
| .id = -1, |
| .num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources), |
| .resource = &omap3evm_smsc911x_resources[0], |
| .dev = { |
| .platform_data = &smsc911x_config, |
| }, |
| }; |
| |
| static inline void __init omap3evm_init_smsc911x(void) |
| { |
| int eth_cs, eth_rst; |
| struct clk *l3ck; |
| unsigned int rate; |
| |
| if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) |
| eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST; |
| else |
| eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST; |
| |
| eth_cs = OMAP3EVM_SMSC911X_CS; |
| |
| l3ck = clk_get(NULL, "l3_ck"); |
| if (IS_ERR(l3ck)) |
| rate = 100000000; |
| else |
| rate = clk_get_rate(l3ck); |
| |
| /* Configure ethernet controller reset gpio */ |
| if (cpu_is_omap3430()) { |
| if (gpio_request(eth_rst, "SMSC911x gpio") < 0) { |
| pr_err(KERN_ERR "Failed to request %d for smsc911x\n", |
| eth_rst); |
| return; |
| } |
| |
| if (gpio_direction_output(eth_rst, 1) < 0) { |
| pr_err(KERN_ERR "Failed to set direction of %d for" \ |
| " smsc911x\n", eth_rst); |
| return; |
| } |
| /* reset pulse to ethernet controller*/ |
| usleep_range(150, 220); |
| gpio_set_value(eth_rst, 0); |
| usleep_range(150, 220); |
| gpio_set_value(eth_rst, 1); |
| usleep_range(1, 2); |
| } |
| |
| if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) { |
| printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", |
| OMAP3EVM_ETHR_GPIO_IRQ); |
| return; |
| } |
| |
| gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ); |
| platform_device_register(&omap3evm_smsc911x_device); |
| } |
| |
| #else |
| static inline void __init omap3evm_init_smsc911x(void) { return; } |
| #endif |
| |
| /* |
| * OMAP3EVM LCD Panel control signals |
| */ |
| #define OMAP3EVM_LCD_PANEL_LR 2 |
| #define OMAP3EVM_LCD_PANEL_UD 3 |
| #define OMAP3EVM_LCD_PANEL_INI 152 |
| #define OMAP3EVM_LCD_PANEL_ENVDD 153 |
| #define OMAP3EVM_LCD_PANEL_QVGA 154 |
| #define OMAP3EVM_LCD_PANEL_RESB 155 |
| #define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210 |
| #define OMAP3EVM_DVI_PANEL_EN_GPIO 199 |
| |
| static int lcd_enabled; |
| static int dvi_enabled; |
| |
| static void __init omap3_evm_display_init(void) |
| { |
| int r; |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_RESB, "lcd_panel_resb"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_resb\n"); |
| return; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_RESB, 1); |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_INI, "lcd_panel_ini"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_ini\n"); |
| goto err_1; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_INI, 1); |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_QVGA, "lcd_panel_qvga"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_qvga\n"); |
| goto err_2; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_QVGA, 0); |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_LR, "lcd_panel_lr"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_lr\n"); |
| goto err_3; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_LR, 1); |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_UD, "lcd_panel_ud"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_ud\n"); |
| goto err_4; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_UD, 1); |
| |
| r = gpio_request(OMAP3EVM_LCD_PANEL_ENVDD, "lcd_panel_envdd"); |
| if (r) { |
| printk(KERN_ERR "failed to get lcd_panel_envdd\n"); |
| goto err_5; |
| } |
| gpio_direction_output(OMAP3EVM_LCD_PANEL_ENVDD, 0); |
| |
| return; |
| |
| err_5: |
| gpio_free(OMAP3EVM_LCD_PANEL_UD); |
| err_4: |
| gpio_free(OMAP3EVM_LCD_PANEL_LR); |
| err_3: |
| gpio_free(OMAP3EVM_LCD_PANEL_QVGA); |
| err_2: |
| gpio_free(OMAP3EVM_LCD_PANEL_INI); |
| err_1: |
| gpio_free(OMAP3EVM_LCD_PANEL_RESB); |
| |
| } |
| |
| static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev) |
| { |
| if (dvi_enabled) { |
| printk(KERN_ERR "cannot enable LCD, DVI is enabled\n"); |
| return -EINVAL; |
| } |
| gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 0); |
| |
| if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) |
| gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0); |
| else |
| gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1); |
| |
| lcd_enabled = 1; |
| return 0; |
| } |
| |
| static void omap3_evm_disable_lcd(struct omap_dss_device *dssdev) |
| { |
| gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 1); |
| |
| if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) |
| gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1); |
| else |
| gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0); |
| |
| lcd_enabled = 0; |
| } |
| |
| static struct omap_dss_device omap3_evm_lcd_device = { |
| .name = "lcd", |
| .driver_name = "sharp_ls_panel", |
| .type = OMAP_DISPLAY_TYPE_DPI, |
| .phy.dpi.data_lines = 18, |
| .platform_enable = omap3_evm_enable_lcd, |
| .platform_disable = omap3_evm_disable_lcd, |
| }; |
| |
| static int omap3_evm_enable_tv(struct omap_dss_device *dssdev) |
| { |
| return 0; |
| } |
| |
| static void omap3_evm_disable_tv(struct omap_dss_device *dssdev) |
| { |
| } |
| |
| static struct omap_dss_device omap3_evm_tv_device = { |
| .name = "tv", |
| .driver_name = "venc", |
| .type = OMAP_DISPLAY_TYPE_VENC, |
| .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO, |
| .platform_enable = omap3_evm_enable_tv, |
| .platform_disable = omap3_evm_disable_tv, |
| }; |
| |
| static int omap3_evm_enable_dvi(struct omap_dss_device *dssdev) |
| { |
| if (lcd_enabled) { |
| printk(KERN_ERR "cannot enable DVI, LCD is enabled\n"); |
| return -EINVAL; |
| } |
| |
| gpio_set_value_cansleep(OMAP3EVM_DVI_PANEL_EN_GPIO, 1); |
| |
| dvi_enabled = 1; |
| return 0; |
| } |
| |
| static void omap3_evm_disable_dvi(struct omap_dss_device *dssdev) |
| { |
| gpio_set_value_cansleep(OMAP3EVM_DVI_PANEL_EN_GPIO, 0); |
| |
| dvi_enabled = 0; |
| } |
| |
| static struct panel_generic_dpi_data dvi_panel = { |
| .name = "generic", |
| .platform_enable = omap3_evm_enable_dvi, |
| .platform_disable = omap3_evm_disable_dvi, |
| }; |
| |
| static struct omap_dss_device omap3_evm_dvi_device = { |
| .name = "dvi", |
| .type = OMAP_DISPLAY_TYPE_DPI, |
| .driver_name = "generic_dpi_panel", |
| .data = &dvi_panel, |
| .phy.dpi.data_lines = 24, |
| }; |
| |
| static struct omap_dss_device *omap3_evm_dss_devices[] = { |
| &omap3_evm_lcd_device, |
| &omap3_evm_tv_device, |
| &omap3_evm_dvi_device, |
| }; |
| |
| static struct omap_dss_board_info omap3_evm_dss_data = { |
| .num_devices = ARRAY_SIZE(omap3_evm_dss_devices), |
| .devices = omap3_evm_dss_devices, |
| .default_device = &omap3_evm_lcd_device, |
| }; |
| |
| static struct regulator_consumer_supply omap3evm_vmmc1_supply = { |
| .supply = "vmmc", |
| }; |
| |
| static struct regulator_consumer_supply omap3evm_vsim_supply = { |
| .supply = "vmmc_aux", |
| }; |
| |
| /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */ |
| static struct regulator_init_data omap3evm_vmmc1 = { |
| .constraints = { |
| .min_uV = 1850000, |
| .max_uV = 3150000, |
| .valid_modes_mask = REGULATOR_MODE_NORMAL |
| | REGULATOR_MODE_STANDBY, |
| .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
| | REGULATOR_CHANGE_MODE |
| | REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3evm_vmmc1_supply, |
| }; |
| |
| /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ |
| static struct regulator_init_data omap3evm_vsim = { |
| .constraints = { |
| .min_uV = 1800000, |
| .max_uV = 3000000, |
| .valid_modes_mask = REGULATOR_MODE_NORMAL |
| | REGULATOR_MODE_STANDBY, |
| .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
| | REGULATOR_CHANGE_MODE |
| | REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3evm_vsim_supply, |
| }; |
| |
| static struct omap2_hsmmc_info mmc[] = { |
| { |
| .mmc = 1, |
| .caps = MMC_CAP_4_BIT_DATA, |
| .gpio_cd = -EINVAL, |
| .gpio_wp = 63, |
| }, |
| #ifdef CONFIG_WL12XX_PLATFORM_DATA |
| { |
| .name = "wl1271", |
| .mmc = 2, |
| .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, |
| .gpio_wp = -EINVAL, |
| .gpio_cd = -EINVAL, |
| .nonremovable = true, |
| }, |
| #endif |
| {} /* Terminator */ |
| }; |
| |
| static struct gpio_led gpio_leds[] = { |
| { |
| .name = "omap3evm::ledb", |
| /* normally not visible (board underside) */ |
| .default_trigger = "default-on", |
| .gpio = -EINVAL, /* gets replaced */ |
| .active_low = true, |
| }, |
| }; |
| |
| static struct gpio_led_platform_data gpio_led_info = { |
| .leds = gpio_leds, |
| .num_leds = ARRAY_SIZE(gpio_leds), |
| }; |
| |
| static struct platform_device leds_gpio = { |
| .name = "leds-gpio", |
| .id = -1, |
| .dev = { |
| .platform_data = &gpio_led_info, |
| }, |
| }; |
| |
| |
| static int omap3evm_twl_gpio_setup(struct device *dev, |
| unsigned gpio, unsigned ngpio) |
| { |
| int r; |
| |
| /* gpio + 0 is "mmc0_cd" (input/IRQ) */ |
| omap_mux_init_gpio(63, OMAP_PIN_INPUT); |
| mmc[0].gpio_cd = gpio + 0; |
| omap2_hsmmc_init(mmc); |
| |
| /* link regulators to MMC adapters */ |
| omap3evm_vmmc1_supply.dev = mmc[0].dev; |
| omap3evm_vsim_supply.dev = mmc[0].dev; |
| |
| /* |
| * Most GPIOs are for USB OTG. Some are mostly sent to |
| * the P2 connector; notably LEDA for the LCD backlight. |
| */ |
| |
| /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */ |
| r = gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL"); |
| if (!r) |
| r = gpio_direction_output(gpio + TWL4030_GPIO_MAX, |
| (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) ? 1 : 0); |
| if (r) |
| printk(KERN_ERR "failed to get/set lcd_bkl gpio\n"); |
| |
| /* gpio + 7 == DVI Enable */ |
| gpio_request(gpio + 7, "EN_DVI"); |
| gpio_direction_output(gpio + 7, 0); |
| |
| /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ |
| gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; |
| |
| platform_device_register(&leds_gpio); |
| |
| return 0; |
| } |
| |
| static struct twl4030_gpio_platform_data omap3evm_gpio_data = { |
| .gpio_base = OMAP_MAX_GPIO_LINES, |
| .irq_base = TWL4030_GPIO_IRQ_BASE, |
| .irq_end = TWL4030_GPIO_IRQ_END, |
| .use_leds = true, |
| .setup = omap3evm_twl_gpio_setup, |
| }; |
| |
| static struct twl4030_usb_data omap3evm_usb_data = { |
| .usb_mode = T2_USB_MODE_ULPI, |
| }; |
| |
| static uint32_t board_keymap[] = { |
| KEY(0, 0, KEY_LEFT), |
| KEY(0, 1, KEY_DOWN), |
| KEY(0, 2, KEY_ENTER), |
| KEY(0, 3, KEY_M), |
| |
| KEY(1, 0, KEY_RIGHT), |
| KEY(1, 1, KEY_UP), |
| KEY(1, 2, KEY_I), |
| KEY(1, 3, KEY_N), |
| |
| KEY(2, 0, KEY_A), |
| KEY(2, 1, KEY_E), |
| KEY(2, 2, KEY_J), |
| KEY(2, 3, KEY_O), |
| |
| KEY(3, 0, KEY_B), |
| KEY(3, 1, KEY_F), |
| KEY(3, 2, KEY_K), |
| KEY(3, 3, KEY_P) |
| }; |
| |
| static struct matrix_keymap_data board_map_data = { |
| .keymap = board_keymap, |
| .keymap_size = ARRAY_SIZE(board_keymap), |
| }; |
| |
| static struct twl4030_keypad_data omap3evm_kp_data = { |
| .keymap_data = &board_map_data, |
| .rows = 4, |
| .cols = 4, |
| .rep = 1, |
| }; |
| |
| static struct twl4030_madc_platform_data omap3evm_madc_data = { |
| .irq_line = 1, |
| }; |
| |
| static struct twl4030_codec_audio_data omap3evm_audio_data; |
| |
| static struct twl4030_codec_data omap3evm_codec_data = { |
| .audio_mclk = 26000000, |
| .audio = &omap3evm_audio_data, |
| }; |
| |
| static struct regulator_consumer_supply omap3_evm_vdda_dac_supply = |
| REGULATOR_SUPPLY("vdda_dac", "omapdss"); |
| |
| /* VDAC for DSS driving S-Video */ |
| static struct regulator_init_data omap3_evm_vdac = { |
| .constraints = { |
| .min_uV = 1800000, |
| .max_uV = 1800000, |
| .apply_uV = true, |
| .valid_modes_mask = REGULATOR_MODE_NORMAL |
| | REGULATOR_MODE_STANDBY, |
| .valid_ops_mask = REGULATOR_CHANGE_MODE |
| | REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3_evm_vdda_dac_supply, |
| }; |
| |
| /* VPLL2 for digital video outputs */ |
| static struct regulator_consumer_supply omap3_evm_vpll2_supply = |
| REGULATOR_SUPPLY("vdds_dsi", "omapdss"); |
| |
| static struct regulator_init_data omap3_evm_vpll2 = { |
| .constraints = { |
| .min_uV = 1800000, |
| .max_uV = 1800000, |
| .apply_uV = true, |
| .valid_modes_mask = REGULATOR_MODE_NORMAL |
| | REGULATOR_MODE_STANDBY, |
| .valid_ops_mask = REGULATOR_CHANGE_MODE |
| | REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3_evm_vpll2_supply, |
| }; |
| |
| /* ads7846 on SPI */ |
| static struct regulator_consumer_supply omap3evm_vio_supply = |
| REGULATOR_SUPPLY("vcc", "spi1.0"); |
| |
| /* VIO for ads7846 */ |
| static struct regulator_init_data omap3evm_vio = { |
| .constraints = { |
| .min_uV = 1800000, |
| .max_uV = 1800000, |
| .apply_uV = true, |
| .valid_modes_mask = REGULATOR_MODE_NORMAL |
| | REGULATOR_MODE_STANDBY, |
| .valid_ops_mask = REGULATOR_CHANGE_MODE |
| | REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3evm_vio_supply, |
| }; |
| |
| #ifdef CONFIG_WL12XX_PLATFORM_DATA |
| |
| #define OMAP3EVM_WLAN_PMENA_GPIO (150) |
| #define OMAP3EVM_WLAN_IRQ_GPIO (149) |
| |
| static struct regulator_consumer_supply omap3evm_vmmc2_supply = |
| REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"); |
| |
| /* VMMC2 for driving the WL12xx module */ |
| static struct regulator_init_data omap3evm_vmmc2 = { |
| .constraints = { |
| .valid_ops_mask = REGULATOR_CHANGE_STATUS, |
| }, |
| .num_consumer_supplies = 1, |
| .consumer_supplies = &omap3evm_vmmc2_supply, |
| }; |
| |
| static struct fixed_voltage_config omap3evm_vwlan = { |
| .supply_name = "vwl1271", |
| .microvolts = 1800000, /* 1.80V */ |
| .gpio = OMAP3EVM_WLAN_PMENA_GPIO, |
| .startup_delay = 70000, /* 70ms */ |
| .enable_high = 1, |
| .enabled_at_boot = 0, |
| .init_data = &omap3evm_vmmc2, |
| }; |
| |
| static struct platform_device omap3evm_wlan_regulator = { |
| .name = "reg-fixed-voltage", |
| .id = 1, |
| .dev = { |
| .platform_data = &omap3evm_vwlan, |
| }, |
| }; |
| |
| struct wl12xx_platform_data omap3evm_wlan_data __initdata = { |
| .irq = OMAP_GPIO_IRQ(OMAP3EVM_WLAN_IRQ_GPIO), |
| .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */ |
| }; |
| #endif |
| |
| static struct twl4030_platform_data omap3evm_twldata = { |
| .irq_base = TWL4030_IRQ_BASE, |
| .irq_end = TWL4030_IRQ_END, |
| |
| /* platform_data for children goes here */ |
| .keypad = &omap3evm_kp_data, |
| .madc = &omap3evm_madc_data, |
| .usb = &omap3evm_usb_data, |
| .gpio = &omap3evm_gpio_data, |
| .codec = &omap3evm_codec_data, |
| .vdac = &omap3_evm_vdac, |
| .vpll2 = &omap3_evm_vpll2, |
| .vio = &omap3evm_vio, |
| }; |
| |
| static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = { |
| { |
| I2C_BOARD_INFO("twl4030", 0x48), |
| .flags = I2C_CLIENT_WAKE, |
| .irq = INT_34XX_SYS_NIRQ, |
| .platform_data = &omap3evm_twldata, |
| }, |
| }; |
| |
| static int __init omap3_evm_i2c_init(void) |
| { |
| /* |
| * REVISIT: These entries can be set in omap3evm_twl_data |
| * after a merge with MFD tree |
| */ |
| omap3evm_twldata.vmmc1 = &omap3evm_vmmc1; |
| omap3evm_twldata.vsim = &omap3evm_vsim; |
| |
| omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo, |
| ARRAY_SIZE(omap3evm_i2c_boardinfo)); |
| omap_register_i2c_bus(2, 400, NULL, 0); |
| omap_register_i2c_bus(3, 400, NULL, 0); |
| return 0; |
| } |
| |
| static void ads7846_dev_init(void) |
| { |
| if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0) |
| printk(KERN_ERR "can't get ads7846 pen down GPIO\n"); |
| |
| gpio_direction_input(OMAP3_EVM_TS_GPIO); |
| gpio_set_debounce(OMAP3_EVM_TS_GPIO, 310); |
| } |
| |
| static int ads7846_get_pendown_state(void) |
| { |
| return !gpio_get_value(OMAP3_EVM_TS_GPIO); |
| } |
| |
| static struct ads7846_platform_data ads7846_config = { |
| .x_max = 0x0fff, |
| .y_max = 0x0fff, |
| .x_plate_ohms = 180, |
| .pressure_max = 255, |
| .debounce_max = 10, |
| .debounce_tol = 3, |
| .debounce_rep = 1, |
| .get_pendown_state = ads7846_get_pendown_state, |
| .keep_vref_on = 1, |
| .settle_delay_usecs = 150, |
| .wakeup = true, |
| }; |
| |
| static struct omap2_mcspi_device_config ads7846_mcspi_config = { |
| .turbo_mode = 0, |
| .single_channel = 1, /* 0: slave, 1: master */ |
| }; |
| |
| static struct spi_board_info omap3evm_spi_board_info[] = { |
| [0] = { |
| .modalias = "ads7846", |
| .bus_num = 1, |
| .chip_select = 0, |
| .max_speed_hz = 1500000, |
| .controller_data = &ads7846_mcspi_config, |
| .irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO), |
| .platform_data = &ads7846_config, |
| }, |
| }; |
| |
| static struct omap_board_config_kernel omap3_evm_config[] __initdata = { |
| }; |
| |
| static void __init omap3_evm_init_early(void) |
| { |
| omap2_init_common_infrastructure(); |
| omap2_init_common_devices(mt46h32m32lf6_sdrc_params, NULL); |
| } |
| |
| static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = { |
| |
| .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN, |
| .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY, |
| .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, |
| |
| .phy_reset = true, |
| /* PHY reset GPIO will be runtime programmed based on EVM version */ |
| .reset_gpio_port[0] = -EINVAL, |
| .reset_gpio_port[1] = -EINVAL, |
| .reset_gpio_port[2] = -EINVAL |
| }; |
| |
| #ifdef CONFIG_OMAP_MUX |
| static struct omap_board_mux omap35x_board_mux[] __initdata = { |
| OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | |
| OMAP_PIN_OFF_WAKEUPENABLE), |
| OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | |
| OMAP_PIN_OFF_WAKEUPENABLE), |
| OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_NONE), |
| #ifdef CONFIG_WL12XX_PLATFORM_DATA |
| /* WLAN IRQ - GPIO 149 */ |
| OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), |
| |
| /* WLAN POWER ENABLE - GPIO 150 */ |
| OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), |
| |
| /* MMC2 SDIO pin muxes for WL12xx */ |
| OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| #endif |
| { .reg_offset = OMAP_MUX_TERMINATOR }, |
| }; |
| |
| static struct omap_board_mux omap36x_board_mux[] __initdata = { |
| OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | |
| OMAP_PIN_OFF_WAKEUPENABLE), |
| OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | |
| OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | |
| OMAP_PIN_OFF_WAKEUPENABLE), |
| /* AM/DM37x EVM: DSS data bus muxed with sys_boot */ |
| OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), |
| #ifdef CONFIG_WL12XX_PLATFORM_DATA |
| /* WLAN IRQ - GPIO 149 */ |
| OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), |
| |
| /* WLAN POWER ENABLE - GPIO 150 */ |
| OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), |
| |
| /* MMC2 SDIO pin muxes for WL12xx */ |
| OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), |
| #endif |
| |
| { .reg_offset = OMAP_MUX_TERMINATOR }, |
| }; |
| #else |
| #define omap35x_board_mux NULL |
| #define omap36x_board_mux NULL |
| #endif |
| |
| static struct omap_musb_board_data musb_board_data = { |
| .interface_type = MUSB_INTERFACE_ULPI, |
| .mode = MUSB_OTG, |
| .power = 100, |
| }; |
| |
| static void __init omap3_evm_init(void) |
| { |
| omap3_evm_get_revision(); |
| |
| if (cpu_is_omap3630()) |
| omap3_mux_init(omap36x_board_mux, OMAP_PACKAGE_CBB); |
| else |
| omap3_mux_init(omap35x_board_mux, OMAP_PACKAGE_CBB); |
| |
| omap_board_config = omap3_evm_config; |
| omap_board_config_size = ARRAY_SIZE(omap3_evm_config); |
| |
| omap3_evm_i2c_init(); |
| |
| omap_display_init(&omap3_evm_dss_data); |
| |
| spi_register_board_info(omap3evm_spi_board_info, |
| ARRAY_SIZE(omap3evm_spi_board_info)); |
| |
| omap_serial_init(); |
| |
| /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ |
| usb_nop_xceiv_register(); |
| |
| if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { |
| /* enable EHCI VBUS using GPIO22 */ |
| omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP); |
| gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS"); |
| gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0); |
| gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1); |
| |
| /* Select EHCI port on main board */ |
| omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP); |
| gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port"); |
| gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0); |
| gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0); |
| |
| /* setup EHCI phy reset config */ |
| omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); |
| ehci_pdata.reset_gpio_port[1] = 21; |
| |
| /* EVM REV >= E can supply 500mA with EXTVBUS programming */ |
| musb_board_data.power = 500; |
| musb_board_data.extvbus = 1; |
| } else { |
| /* setup EHCI phy reset on MDC */ |
| omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); |
| ehci_pdata.reset_gpio_port[1] = 135; |
| } |
| usb_musb_init(&musb_board_data); |
| usb_ehci_init(&ehci_pdata); |
| ads7846_dev_init(); |
| omap3evm_init_smsc911x(); |
| omap3_evm_display_init(); |
| |
| #ifdef CONFIG_WL12XX_PLATFORM_DATA |
| /* WL12xx WLAN Init */ |
| if (wl12xx_set_platform_data(&omap3evm_wlan_data)) |
| pr_err("error setting wl12xx data\n"); |
| platform_device_register(&omap3evm_wlan_regulator); |
| #endif |
| } |
| |
| MACHINE_START(OMAP3EVM, "OMAP3 EVM") |
| /* Maintainer: Syed Mohammed Khasim - Texas Instruments */ |
| .boot_params = 0x80000100, |
| .reserve = omap_reserve, |
| .map_io = omap3_map_io, |
| .init_early = omap3_evm_init_early, |
| .init_irq = omap_init_irq, |
| .init_machine = omap3_evm_init, |
| .timer = &omap_timer, |
| MACHINE_END |