| /* |
| * drivers/net/phy/micrel.c |
| * |
| * Driver for Micrel PHYs |
| * |
| * Author: David J. Choi |
| * |
| * Copyright (c) 2010-2013 Micrel, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| * |
| * Support : Micrel Phys: |
| * Giga phys: ksz9021, ksz9031 |
| * 100/10 Phys : ksz8001, ksz8721, ksz8737, ksz8041 |
| * ksz8021, ksz8031, ksz8051, |
| * ksz8081, ksz8091, |
| * ksz8061, |
| * Switch : ksz8873, ksz886x |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/phy.h> |
| #include <linux/micrel_phy.h> |
| |
| /* Operation Mode Strap Override */ |
| #define MII_KSZPHY_OMSO 0x16 |
| #define KSZPHY_OMSO_B_CAST_OFF (1 << 9) |
| #define KSZPHY_OMSO_RMII_OVERRIDE (1 << 1) |
| #define KSZPHY_OMSO_MII_OVERRIDE (1 << 0) |
| |
| /* general Interrupt control/status reg in vendor specific block. */ |
| #define MII_KSZPHY_INTCS 0x1B |
| #define KSZPHY_INTCS_JABBER (1 << 15) |
| #define KSZPHY_INTCS_RECEIVE_ERR (1 << 14) |
| #define KSZPHY_INTCS_PAGE_RECEIVE (1 << 13) |
| #define KSZPHY_INTCS_PARELLEL (1 << 12) |
| #define KSZPHY_INTCS_LINK_PARTNER_ACK (1 << 11) |
| #define KSZPHY_INTCS_LINK_DOWN (1 << 10) |
| #define KSZPHY_INTCS_REMOTE_FAULT (1 << 9) |
| #define KSZPHY_INTCS_LINK_UP (1 << 8) |
| #define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\ |
| KSZPHY_INTCS_LINK_DOWN) |
| |
| /* general PHY control reg in vendor specific block. */ |
| #define MII_KSZPHY_CTRL 0x1F |
| /* bitmap of PHY register to set interrupt mode */ |
| #define KSZPHY_CTRL_INT_ACTIVE_HIGH (1 << 9) |
| #define KSZ9021_CTRL_INT_ACTIVE_HIGH (1 << 14) |
| #define KS8737_CTRL_INT_ACTIVE_HIGH (1 << 14) |
| #define KSZ8051_RMII_50MHZ_CLK (1 << 7) |
| |
| static int ksz_config_flags(struct phy_device *phydev) |
| { |
| int regval; |
| |
| if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) { |
| regval = phy_read(phydev, MII_KSZPHY_CTRL); |
| regval |= KSZ8051_RMII_50MHZ_CLK; |
| return phy_write(phydev, MII_KSZPHY_CTRL, regval); |
| } |
| return 0; |
| } |
| |
| static int kszphy_ack_interrupt(struct phy_device *phydev) |
| { |
| /* bit[7..0] int status, which is a read and clear register. */ |
| int rc; |
| |
| rc = phy_read(phydev, MII_KSZPHY_INTCS); |
| |
| return (rc < 0) ? rc : 0; |
| } |
| |
| static int kszphy_set_interrupt(struct phy_device *phydev) |
| { |
| int temp; |
| temp = (PHY_INTERRUPT_ENABLED == phydev->interrupts) ? |
| KSZPHY_INTCS_ALL : 0; |
| return phy_write(phydev, MII_KSZPHY_INTCS, temp); |
| } |
| |
| static int kszphy_config_intr(struct phy_device *phydev) |
| { |
| int temp, rc; |
| |
| /* set the interrupt pin active low */ |
| temp = phy_read(phydev, MII_KSZPHY_CTRL); |
| temp &= ~KSZPHY_CTRL_INT_ACTIVE_HIGH; |
| phy_write(phydev, MII_KSZPHY_CTRL, temp); |
| rc = kszphy_set_interrupt(phydev); |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int ksz9021_config_intr(struct phy_device *phydev) |
| { |
| int temp, rc; |
| |
| /* set the interrupt pin active low */ |
| temp = phy_read(phydev, MII_KSZPHY_CTRL); |
| temp &= ~KSZ9021_CTRL_INT_ACTIVE_HIGH; |
| phy_write(phydev, MII_KSZPHY_CTRL, temp); |
| rc = kszphy_set_interrupt(phydev); |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int ks8737_config_intr(struct phy_device *phydev) |
| { |
| int temp, rc; |
| |
| /* set the interrupt pin active low */ |
| temp = phy_read(phydev, MII_KSZPHY_CTRL); |
| temp &= ~KS8737_CTRL_INT_ACTIVE_HIGH; |
| phy_write(phydev, MII_KSZPHY_CTRL, temp); |
| rc = kszphy_set_interrupt(phydev); |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int kszphy_config_init(struct phy_device *phydev) |
| { |
| return 0; |
| } |
| |
| static int ksz8021_config_init(struct phy_device *phydev) |
| { |
| int rc; |
| const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE; |
| phy_write(phydev, MII_KSZPHY_OMSO, val); |
| rc = ksz_config_flags(phydev); |
| return rc < 0 ? rc : 0; |
| } |
| |
| static int ks8051_config_init(struct phy_device *phydev) |
| { |
| int rc; |
| |
| rc = ksz_config_flags(phydev); |
| return rc < 0 ? rc : 0; |
| } |
| |
| #define KSZ8873MLL_GLOBAL_CONTROL_4 0x06 |
| #define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX (1 << 6) |
| #define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED (1 << 4) |
| int ksz8873mll_read_status(struct phy_device *phydev) |
| { |
| int regval; |
| |
| /* dummy read */ |
| regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4); |
| |
| regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4); |
| |
| if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX) |
| phydev->duplex = DUPLEX_HALF; |
| else |
| phydev->duplex = DUPLEX_FULL; |
| |
| if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_SPEED) |
| phydev->speed = SPEED_10; |
| else |
| phydev->speed = SPEED_100; |
| |
| phydev->link = 1; |
| phydev->pause = phydev->asym_pause = 0; |
| |
| return 0; |
| } |
| |
| static int ksz8873mll_config_aneg(struct phy_device *phydev) |
| { |
| return 0; |
| } |
| |
| static struct phy_driver ksphy_driver[] = { |
| { |
| .phy_id = PHY_ID_KS8737, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KS8737", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = ks8737_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8021, |
| .phy_id_mask = 0x00ffffff, |
| .name = "Micrel KSZ8021 or KSZ8031", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause | |
| SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = ksz8021_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8031, |
| .phy_id_mask = 0x00ffffff, |
| .name = "Micrel KSZ8031", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause | |
| SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = ksz8021_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8041, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KSZ8041", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
| | SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8051, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KSZ8051", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
| | SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = ks8051_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8001, |
| .name = "Micrel KSZ8001 or KS8721", |
| .phy_id_mask = 0x00ffffff, |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8081, |
| .name = "Micrel KSZ8081 or KSZ8091", |
| .phy_id_mask = 0x00fffff0, |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ8061, |
| .name = "Micrel KSZ8061", |
| .phy_id_mask = 0x00fffff0, |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = kszphy_config_intr, |
| .driver = { .owner = THIS_MODULE,}, |
| }, { |
| .phy_id = PHY_ID_KSZ9021, |
| .phy_id_mask = 0x000ffffe, |
| .name = "Micrel KSZ9021 Gigabit PHY", |
| .features = (PHY_GBIT_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = ksz9021_config_intr, |
| .driver = { .owner = THIS_MODULE, }, |
| }, { |
| .phy_id = PHY_ID_KSZ9031, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KSZ9031 Gigabit PHY", |
| .features = (PHY_GBIT_FEATURES | SUPPORTED_Pause |
| | SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .ack_interrupt = kszphy_ack_interrupt, |
| .config_intr = ksz9021_config_intr, |
| .driver = { .owner = THIS_MODULE, }, |
| }, { |
| .phy_id = PHY_ID_KSZ8873MLL, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KSZ8873MLL Switch", |
| .features = (SUPPORTED_Pause | SUPPORTED_Asym_Pause), |
| .flags = PHY_HAS_MAGICANEG, |
| .config_init = kszphy_config_init, |
| .config_aneg = ksz8873mll_config_aneg, |
| .read_status = ksz8873mll_read_status, |
| .driver = { .owner = THIS_MODULE, }, |
| }, { |
| .phy_id = PHY_ID_KSZ886X, |
| .phy_id_mask = 0x00fffff0, |
| .name = "Micrel KSZ886X Switch", |
| .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), |
| .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, |
| .config_init = kszphy_config_init, |
| .config_aneg = genphy_config_aneg, |
| .read_status = genphy_read_status, |
| .driver = { .owner = THIS_MODULE, }, |
| } }; |
| |
| static int __init ksphy_init(void) |
| { |
| return phy_drivers_register(ksphy_driver, |
| ARRAY_SIZE(ksphy_driver)); |
| } |
| |
| static void __exit ksphy_exit(void) |
| { |
| phy_drivers_unregister(ksphy_driver, |
| ARRAY_SIZE(ksphy_driver)); |
| } |
| |
| module_init(ksphy_init); |
| module_exit(ksphy_exit); |
| |
| MODULE_DESCRIPTION("Micrel PHY driver"); |
| MODULE_AUTHOR("David J. Choi"); |
| MODULE_LICENSE("GPL"); |
| |
| static struct mdio_device_id __maybe_unused micrel_tbl[] = { |
| { PHY_ID_KSZ9021, 0x000ffffe }, |
| { PHY_ID_KSZ9031, 0x00fffff0 }, |
| { PHY_ID_KSZ8001, 0x00ffffff }, |
| { PHY_ID_KS8737, 0x00fffff0 }, |
| { PHY_ID_KSZ8021, 0x00ffffff }, |
| { PHY_ID_KSZ8031, 0x00ffffff }, |
| { PHY_ID_KSZ8041, 0x00fffff0 }, |
| { PHY_ID_KSZ8051, 0x00fffff0 }, |
| { PHY_ID_KSZ8061, 0x00fffff0 }, |
| { PHY_ID_KSZ8081, 0x00fffff0 }, |
| { PHY_ID_KSZ8873MLL, 0x00fffff0 }, |
| { PHY_ID_KSZ886X, 0x00fffff0 }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(mdio, micrel_tbl); |