diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
new file mode 100644
index 0000000..90faa98
--- /dev/null
+++ b/include/linux/mfd/stmpe.h
@@ -0,0 +1,197 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License, version 2
+ * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
+ */
+
+#ifndef __LINUX_MFD_STMPE_H
+#define __LINUX_MFD_STMPE_H
+
+#include <linux/device.h>
+
+enum stmpe_block {
+	STMPE_BLOCK_GPIO	= 1 << 0,
+	STMPE_BLOCK_KEYPAD	= 1 << 1,
+	STMPE_BLOCK_TOUCHSCREEN	= 1 << 2,
+	STMPE_BLOCK_ADC		= 1 << 3,
+	STMPE_BLOCK_PWM		= 1 << 4,
+	STMPE_BLOCK_ROTATOR	= 1 << 5,
+};
+
+enum stmpe_partnum {
+	STMPE811,
+	STMPE1601,
+	STMPE2401,
+	STMPE2403,
+};
+
+/*
+ * For registers whose locations differ on variants,  the correct address is
+ * obtained by indexing stmpe->regs with one of the following.
+ */
+enum {
+	STMPE_IDX_CHIP_ID,
+	STMPE_IDX_ICR_LSB,
+	STMPE_IDX_IER_LSB,
+	STMPE_IDX_ISR_MSB,
+	STMPE_IDX_GPMR_LSB,
+	STMPE_IDX_GPSR_LSB,
+	STMPE_IDX_GPCR_LSB,
+	STMPE_IDX_GPDR_LSB,
+	STMPE_IDX_GPEDR_MSB,
+	STMPE_IDX_GPRER_LSB,
+	STMPE_IDX_GPFER_LSB,
+	STMPE_IDX_GPAFR_U_MSB,
+	STMPE_IDX_IEGPIOR_LSB,
+	STMPE_IDX_ISGPIOR_MSB,
+	STMPE_IDX_MAX,
+};
+
+
+struct stmpe_variant_info;
+
+/**
+ * struct stmpe - STMPE MFD structure
+ * @lock: lock protecting I/O operations
+ * @irq_lock: IRQ bus lock
+ * @dev: device, mostly for dev_dbg()
+ * @i2c: i2c client
+ * @variant: the detected STMPE model number
+ * @regs: list of addresses of registers which are at different addresses on
+ *	  different variants.  Indexed by one of STMPE_IDX_*.
+ * @irq_base: starting IRQ number for internal IRQs
+ * @num_gpios: number of gpios, differs for variants
+ * @ier: cache of IER registers for bus_lock
+ * @oldier: cache of IER registers for bus_lock
+ * @pdata: platform data
+ */
+struct stmpe {
+	struct mutex lock;
+	struct mutex irq_lock;
+	struct device *dev;
+	struct i2c_client *i2c;
+	enum stmpe_partnum partnum;
+	struct stmpe_variant_info *variant;
+	const u8 *regs;
+
+	int irq_base;
+	int num_gpios;
+	u8 ier[2];
+	u8 oldier[2];
+	struct stmpe_platform_data *pdata;
+};
+
+extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data);
+extern int stmpe_reg_read(struct stmpe *stmpe, u8 reg);
+extern int stmpe_block_read(struct stmpe *stmpe, u8 reg, u8 length,
+			    u8 *values);
+extern int stmpe_block_write(struct stmpe *stmpe, u8 reg, u8 length,
+			     const u8 *values);
+extern int stmpe_set_bits(struct stmpe *stmpe, u8 reg, u8 mask, u8 val);
+extern int stmpe_set_altfunc(struct stmpe *stmpe, u32 pins,
+			     enum stmpe_block block);
+extern int stmpe_enable(struct stmpe *stmpe, unsigned int blocks);
+extern int stmpe_disable(struct stmpe *stmpe, unsigned int blocks);
+
+struct matrix_keymap_data;
+
+/**
+ * struct stmpe_keypad_platform_data - STMPE keypad platform data
+ * @keymap_data: key map table and size
+ * @debounce_ms: debounce interval, in ms.  Maximum is
+ *		 %STMPE_KEYPAD_MAX_DEBOUNCE.
+ * @scan_count: number of key scanning cycles to confirm key data.
+ *		Maximum is %STMPE_KEYPAD_MAX_SCAN_COUNT.
+ * @no_autorepeat: disable key autorepeat
+ */
+struct stmpe_keypad_platform_data {
+	struct matrix_keymap_data *keymap_data;
+	unsigned int debounce_ms;
+	unsigned int scan_count;
+	bool no_autorepeat;
+};
+
+/**
+ * struct stmpe_gpio_platform_data - STMPE GPIO platform data
+ * @gpio_base: first gpio number assigned.  A maximum of
+ *	       %STMPE_NR_GPIOS GPIOs will be allocated.
+ */
+struct stmpe_gpio_platform_data {
+	int gpio_base;
+	void (*setup)(struct stmpe *stmpe, unsigned gpio_base);
+	void (*remove)(struct stmpe *stmpe, unsigned gpio_base);
+};
+
+/**
+ * struct stmpe_ts_platform_data - stmpe811 touch screen controller platform
+ * data
+ * @sample_time: ADC converstion time in number of clock.
+ * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
+ * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
+ * recommended is 4.
+ * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
+ * @ref_sel: ADC reference source
+ * (0 -> internal reference, 1 -> external reference)
+ * @adc_freq: ADC Clock speed
+ * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
+ * @ave_ctrl: Sample average control
+ * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
+ * @touch_det_delay: Touch detect interrupt delay
+ * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
+ * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
+ * recommended is 3
+ * @settling: Panel driver settling time
+ * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
+ * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
+ * recommended is 2
+ * @fraction_z: Length of the fractional part in z
+ * (fraction_z ([0..7]) = Count of the fractional part)
+ * recommended is 7
+ * @i_drive: current limit value of the touchscreen drivers
+ * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
+ *
+ * */
+struct stmpe_ts_platform_data {
+       u8 sample_time;
+       u8 mod_12b;
+       u8 ref_sel;
+       u8 adc_freq;
+       u8 ave_ctrl;
+       u8 touch_det_delay;
+       u8 settling;
+       u8 fraction_z;
+       u8 i_drive;
+};
+
+/**
+ * struct stmpe_platform_data - STMPE platform data
+ * @id: device id to distinguish between multiple STMPEs on the same board
+ * @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
+ * @irq_trigger: IRQ trigger to use for the interrupt to the host
+ * @irq_invert_polarity: IRQ line is connected with reversed polarity
+ * @irq_base: base IRQ number.  %STMPE_NR_IRQS irqs will be used, or
+ *	      %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
+ * @gpio: GPIO-specific platform data
+ * @keypad: keypad-specific platform data
+ * @ts: touchscreen-specific platform data
+ */
+struct stmpe_platform_data {
+	int id;
+	unsigned int blocks;
+	int irq_base;
+	unsigned int irq_trigger;
+	bool irq_invert_polarity;
+
+	struct stmpe_gpio_platform_data *gpio;
+	struct stmpe_keypad_platform_data *keypad;
+	struct stmpe_ts_platform_data *ts;
+};
+
+#define STMPE_NR_INTERNAL_IRQS	9
+#define STMPE_INT_GPIO(x)	(STMPE_NR_INTERNAL_IRQS + (x))
+
+#define STMPE_NR_GPIOS		24
+#define STMPE_NR_IRQS		STMPE_INT_GPIO(STMPE_NR_GPIOS)
+
+#endif