[SCSI] hpsa: add ioaccell mode 1 RAID offload support.
This enables sending i/o's destined for RAID logical drives
which can be serviced by a single physical disk down a different,
faster i/o path directly to physical drives for certain logical
volumes on SSDs bypassing the Smart Array RAID stack for a
performance improvement.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 4b6db4c..e8489a9 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -49,6 +49,7 @@
#include <linux/atomic.h>
#include <linux/kthread.h>
#include <linux/jiffies.h>
+#include <asm/div64.h>
#include "hpsa_cmd.h"
#include "hpsa.h"
@@ -216,6 +217,7 @@
static int hpsa_wait_for_board_state(struct pci_dev *pdev, void __iomem *vaddr,
int wait_for_ready);
static inline void finish_cmd(struct CommandList *c);
+static void hpsa_wait_for_mode_change_ack(struct ctlr_info *h);
#define BOARD_NOT_READY 0
#define BOARD_READY 1
@@ -1195,6 +1197,7 @@
struct scsi_cmnd *cmd;
struct ctlr_info *h;
struct ErrorInfo *ei;
+ struct hpsa_scsi_dev_t *dev;
unsigned char sense_key;
unsigned char asc; /* additional sense code */
@@ -1204,6 +1207,7 @@
ei = cp->err_info;
cmd = (struct scsi_cmnd *) cp->scsi_cmd;
h = cp->h;
+ dev = cmd->device->hostdata;
scsi_dma_unmap(cmd); /* undo the DMA mappings */
if ((cp->cmd_type == CMD_SCSI) &&
@@ -1242,6 +1246,19 @@
cp->Header.Tag.upper = c->Tag.upper;
memcpy(cp->Header.LUN.LunAddrBytes, c->CISS_LUN, 8);
memcpy(cp->Request.CDB, c->CDB, cp->Request.CDBLen);
+
+ /* Any RAID offload error results in retry which will use
+ * the normal I/O path so the controller can handle whatever's
+ * wrong.
+ */
+ if (is_logical_dev_addr_mode(dev->scsi3addr)) {
+ if (ei->CommandStatus == CMD_IOACCEL_DISABLED)
+ dev->offload_enabled = 0;
+ cmd->result = DID_SOFT_ERROR << 16;
+ cmd_free(h, cp);
+ cmd->scsi_done(cmd);
+ return;
+ }
}
/* an error has occurred */
@@ -1406,6 +1423,14 @@
cmd->result = DID_ERROR << 16;
dev_warn(&h->pdev->dev, "Command unabortable\n");
break;
+ case CMD_IOACCEL_DISABLED:
+ /* This only handles the direct pass-through case since RAID
+ * offload is handled above. Just attempt a retry.
+ */
+ cmd->result = DID_SOFT_ERROR << 16;
+ dev_warn(&h->pdev->dev,
+ "cp %p had HP SSD Smart Path error\n", cp);
+ break;
default:
cmd->result = DID_ERROR << 16;
dev_warn(&h->pdev->dev, "cp %p returned unknown status %x\n",
@@ -1650,6 +1675,147 @@
return;
}
+#define HPSA_MAP_DEBUG
+#ifdef HPSA_MAP_DEBUG
+static void hpsa_debug_map_buff(struct ctlr_info *h, int rc,
+ struct raid_map_data *map_buff)
+{
+ struct raid_map_disk_data *dd = &map_buff->data[0];
+ int map, row, col;
+ u16 map_cnt, row_cnt, disks_per_row;
+
+ if (rc != 0)
+ return;
+
+ dev_info(&h->pdev->dev, "structure_size = %u\n",
+ le32_to_cpu(map_buff->structure_size));
+ dev_info(&h->pdev->dev, "volume_blk_size = %u\n",
+ le32_to_cpu(map_buff->volume_blk_size));
+ dev_info(&h->pdev->dev, "volume_blk_cnt = 0x%llx\n",
+ le64_to_cpu(map_buff->volume_blk_cnt));
+ dev_info(&h->pdev->dev, "physicalBlockShift = %u\n",
+ map_buff->phys_blk_shift);
+ dev_info(&h->pdev->dev, "parity_rotation_shift = %u\n",
+ map_buff->parity_rotation_shift);
+ dev_info(&h->pdev->dev, "strip_size = %u\n",
+ le16_to_cpu(map_buff->strip_size));
+ dev_info(&h->pdev->dev, "disk_starting_blk = 0x%llx\n",
+ le64_to_cpu(map_buff->disk_starting_blk));
+ dev_info(&h->pdev->dev, "disk_blk_cnt = 0x%llx\n",
+ le64_to_cpu(map_buff->disk_blk_cnt));
+ dev_info(&h->pdev->dev, "data_disks_per_row = %u\n",
+ le16_to_cpu(map_buff->data_disks_per_row));
+ dev_info(&h->pdev->dev, "metadata_disks_per_row = %u\n",
+ le16_to_cpu(map_buff->metadata_disks_per_row));
+ dev_info(&h->pdev->dev, "row_cnt = %u\n",
+ le16_to_cpu(map_buff->row_cnt));
+ dev_info(&h->pdev->dev, "layout_map_count = %u\n",
+ le16_to_cpu(map_buff->layout_map_count));
+
+ map_cnt = le16_to_cpu(map_buff->layout_map_count);
+ for (map = 0; map < map_cnt; map++) {
+ dev_info(&h->pdev->dev, "Map%u:\n", map);
+ row_cnt = le16_to_cpu(map_buff->row_cnt);
+ for (row = 0; row < row_cnt; row++) {
+ dev_info(&h->pdev->dev, " Row%u:\n", row);
+ disks_per_row =
+ le16_to_cpu(map_buff->data_disks_per_row);
+ for (col = 0; col < disks_per_row; col++, dd++)
+ dev_info(&h->pdev->dev,
+ " D%02u: h=0x%04x xor=%u,%u\n",
+ col, dd->ioaccel_handle,
+ dd->xor_mult[0], dd->xor_mult[1]);
+ disks_per_row =
+ le16_to_cpu(map_buff->metadata_disks_per_row);
+ for (col = 0; col < disks_per_row; col++, dd++)
+ dev_info(&h->pdev->dev,
+ " M%02u: h=0x%04x xor=%u,%u\n",
+ col, dd->ioaccel_handle,
+ dd->xor_mult[0], dd->xor_mult[1]);
+ }
+ }
+}
+#else
+static void hpsa_debug_map_buff(__attribute__((unused)) struct ctlr_info *h,
+ __attribute__((unused)) int rc,
+ __attribute__((unused)) struct raid_map_data *map_buff)
+{
+}
+#endif
+
+static int hpsa_get_raid_map(struct ctlr_info *h,
+ unsigned char *scsi3addr, struct hpsa_scsi_dev_t *this_device)
+{
+ int rc = 0;
+ struct CommandList *c;
+ struct ErrorInfo *ei;
+
+ c = cmd_special_alloc(h);
+ if (c == NULL) {
+ dev_warn(&h->pdev->dev, "cmd_special_alloc returned NULL!\n");
+ return -ENOMEM;
+ }
+ if (fill_cmd(c, HPSA_GET_RAID_MAP, h, &this_device->raid_map,
+ sizeof(this_device->raid_map), 0,
+ scsi3addr, TYPE_CMD)) {
+ dev_warn(&h->pdev->dev, "Out of memory in hpsa_get_raid_map()\n");
+ cmd_special_free(h, c);
+ return -ENOMEM;
+ }
+ hpsa_scsi_do_simple_cmd_with_retry(h, c, PCI_DMA_FROMDEVICE);
+ ei = c->err_info;
+ if (ei->CommandStatus != 0 && ei->CommandStatus != CMD_DATA_UNDERRUN) {
+ hpsa_scsi_interpret_error(c);
+ cmd_special_free(h, c);
+ return -1;
+ }
+ cmd_special_free(h, c);
+
+ /* @todo in the future, dynamically allocate RAID map memory */
+ if (le32_to_cpu(this_device->raid_map.structure_size) >
+ sizeof(this_device->raid_map)) {
+ dev_warn(&h->pdev->dev, "RAID map size is too large!\n");
+ rc = -1;
+ }
+ hpsa_debug_map_buff(h, rc, &this_device->raid_map);
+ return rc;
+}
+
+static void hpsa_get_ioaccel_status(struct ctlr_info *h,
+ unsigned char *scsi3addr, struct hpsa_scsi_dev_t *this_device)
+{
+ int rc;
+ unsigned char *buf;
+ u8 ioaccel_status;
+
+ this_device->offload_config = 0;
+ this_device->offload_enabled = 0;
+
+ buf = kzalloc(64, GFP_KERNEL);
+ if (!buf)
+ return;
+ rc = hpsa_scsi_do_inquiry(h, scsi3addr,
+ HPSA_VPD_LV_IOACCEL_STATUS, buf, 64);
+ if (rc != 0)
+ goto out;
+
+#define IOACCEL_STATUS_BYTE 4
+#define OFFLOAD_CONFIGURED_BIT 0x01
+#define OFFLOAD_ENABLED_BIT 0x02
+ ioaccel_status = buf[IOACCEL_STATUS_BYTE];
+ this_device->offload_config =
+ !!(ioaccel_status & OFFLOAD_CONFIGURED_BIT);
+ if (this_device->offload_config) {
+ this_device->offload_enabled =
+ !!(ioaccel_status & OFFLOAD_ENABLED_BIT);
+ if (hpsa_get_raid_map(h, scsi3addr, this_device))
+ this_device->offload_enabled = 0;
+ }
+out:
+ kfree(buf);
+ return;
+}
+
/* Get the device id from inquiry page 0x83 */
static int hpsa_get_device_id(struct ctlr_info *h, unsigned char *scsi3addr,
unsigned char *device_id, int buflen)
@@ -1698,6 +1864,14 @@
ei->CommandStatus != CMD_DATA_UNDERRUN) {
hpsa_scsi_interpret_error(c);
rc = -1;
+ } else {
+ if (buf->extended_response_flag != extended_response) {
+ dev_err(&h->pdev->dev,
+ "report luns requested format %u, got %u\n",
+ extended_response,
+ buf->extended_response_flag);
+ rc = -1;
+ }
}
out:
cmd_special_free(h, c);
@@ -1763,10 +1937,15 @@
sizeof(this_device->device_id));
if (this_device->devtype == TYPE_DISK &&
- is_logical_dev_addr_mode(scsi3addr))
+ is_logical_dev_addr_mode(scsi3addr)) {
hpsa_get_raid_level(h, scsi3addr, &this_device->raid_level);
- else
+ if (h->fw_support & MISC_FW_RAID_OFFLOAD_BASIC)
+ hpsa_get_ioaccel_status(h, scsi3addr, this_device);
+ } else {
this_device->raid_level = RAID_UNKNOWN;
+ this_device->offload_config = 0;
+ this_device->offload_enabled = 0;
+ }
if (is_OBDR_device) {
/* See if this is a One-Button-Disaster-Recovery device
@@ -1903,15 +2082,25 @@
*/
static int hpsa_gather_lun_info(struct ctlr_info *h,
int reportlunsize,
- struct ReportLUNdata *physdev, u32 *nphysicals,
+ struct ReportLUNdata *physdev, u32 *nphysicals, int *physical_mode,
struct ReportLUNdata *logdev, u32 *nlogicals)
{
+ int physical_entry_size = 8;
+
+ *physical_mode = 0;
+
+ /* For I/O accelerator mode we need to read physical device handles */
+ if (h->transMethod & CFGTBL_Trans_io_accel1) {
+ *physical_mode = HPSA_REPORT_PHYS_EXTENDED;
+ physical_entry_size = 24;
+ }
if (hpsa_scsi_do_report_phys_luns(h, physdev, reportlunsize,
- HPSA_REPORT_PHYS_EXTENDED)) {
+ *physical_mode)) {
dev_err(&h->pdev->dev, "report physical LUNs failed.\n");
return -1;
}
- *nphysicals = be32_to_cpu(*((__be32 *)physdev->LUNListLength)) / 24;
+ *nphysicals = be32_to_cpu(*((__be32 *)physdev->LUNListLength)) /
+ physical_entry_size;
if (*nphysicals > HPSA_MAX_PHYS_LUN) {
dev_warn(&h->pdev->dev, "maximum physical LUNs (%d) exceeded."
" %d LUNs ignored.\n", HPSA_MAX_PHYS_LUN,
@@ -1983,10 +2172,11 @@
struct ReportLUNdata *logdev_list = NULL;
u32 nphysicals = 0;
u32 nlogicals = 0;
+ int physical_mode = 0;
u32 ndev_allocated = 0;
struct hpsa_scsi_dev_t **currentsd, *this_device, *tmpdevice;
int ncurrent = 0;
- int reportlunsize = sizeof(*physdev_list) + HPSA_MAX_PHYS_LUN * 8;
+ int reportlunsize = sizeof(*physdev_list) + HPSA_MAX_PHYS_LUN * 24;
int i, n_ext_target_devs, ndevs_to_allocate;
int raid_ctlr_position;
DECLARE_BITMAP(lunzerobits, MAX_EXT_TARGETS);
@@ -2004,7 +2194,7 @@
if (hpsa_gather_lun_info(h, reportlunsize,
(struct ReportLUNdata *) physdev_list, &nphysicals,
- logdev_list, &nlogicals))
+ &physical_mode, logdev_list, &nlogicals))
goto out;
/* We might see up to the maximum number of logical and physical disks
@@ -2085,12 +2275,16 @@
ncurrent++;
break;
case TYPE_DISK:
- if (i < nphysicals)
+ if (i >= nphysicals) {
+ ncurrent++;
break;
- memcpy(&this_device->ioaccel_handle,
- &lunaddrbytes[20],
- sizeof(this_device->ioaccel_handle));
- ncurrent++;
+ }
+ if (physical_mode == HPSA_REPORT_PHYS_EXTENDED) {
+ memcpy(&this_device->ioaccel_handle,
+ &lunaddrbytes[20],
+ sizeof(this_device->ioaccel_handle));
+ ncurrent++;
+ }
break;
case TYPE_TAPE:
case TYPE_MEDIUM_CHANGER:
@@ -2184,15 +2378,62 @@
return 0;
}
+#define IO_ACCEL_INELIGIBLE (1)
+static int fixup_ioaccel_cdb(u8 *cdb, int *cdb_len)
+{
+ int is_write = 0;
+ u32 block;
+ u32 block_cnt;
+
+ /* Perform some CDB fixups if needed using 10 byte reads/writes only */
+ switch (cdb[0]) {
+ case WRITE_6:
+ case WRITE_12:
+ is_write = 1;
+ case READ_6:
+ case READ_12:
+ if (*cdb_len == 6) {
+ block = (((u32) cdb[2]) << 8) | cdb[3];
+ block_cnt = cdb[4];
+ } else {
+ BUG_ON(*cdb_len != 12);
+ block = (((u32) cdb[2]) << 24) |
+ (((u32) cdb[3]) << 16) |
+ (((u32) cdb[4]) << 8) |
+ cdb[5];
+ block_cnt =
+ (((u32) cdb[6]) << 24) |
+ (((u32) cdb[7]) << 16) |
+ (((u32) cdb[8]) << 8) |
+ cdb[9];
+ }
+ if (block_cnt > 0xffff)
+ return IO_ACCEL_INELIGIBLE;
+
+ cdb[0] = is_write ? WRITE_10 : READ_10;
+ cdb[1] = 0;
+ cdb[2] = (u8) (block >> 24);
+ cdb[3] = (u8) (block >> 16);
+ cdb[4] = (u8) (block >> 8);
+ cdb[5] = (u8) (block);
+ cdb[6] = 0;
+ cdb[7] = (u8) (block_cnt >> 8);
+ cdb[8] = (u8) (block_cnt);
+ cdb[9] = 0;
+ *cdb_len = 10;
+ break;
+ }
+ return 0;
+}
+
/*
* Queue a command to the I/O accelerator path.
- * This method does not currently support S/G chaining.
*/
static int hpsa_scsi_ioaccel_queue_command(struct ctlr_info *h,
- struct CommandList *c)
+ struct CommandList *c, u32 ioaccel_handle, u8 *cdb, int cdb_len,
+ u8 *scsi3addr)
{
struct scsi_cmnd *cmd = c->scsi_cmd;
- struct hpsa_scsi_dev_t *dev = cmd->device->hostdata;
struct io_accel1_cmd *cp = &h->ioaccel_cmd_pool[c->cmdindex];
unsigned int len;
unsigned int total_len = 0;
@@ -2202,8 +2443,15 @@
struct SGDescriptor *curr_sg;
u32 control = IOACCEL1_CONTROL_SIMPLEQUEUE;
+ /* TODO: implement chaining support */
+ if (scsi_sg_count(cmd) > h->ioaccel_maxsg)
+ return IO_ACCEL_INELIGIBLE;
+
BUG_ON(cmd->cmd_len > IOACCEL1_IOFLAGS_CDBLEN_MAX);
+ if (fixup_ioaccel_cdb(cdb, &cdb_len))
+ return IO_ACCEL_INELIGIBLE;
+
c->cmd_type = CMD_IOACCEL1;
/* Adjust the DMA address to point to the accelerated command buffer */
@@ -2254,13 +2502,13 @@
}
/* Fill out the command structure to submit */
- cp->dev_handle = dev->ioaccel_handle;
+ cp->dev_handle = ioaccel_handle & 0xFFFF;
cp->transfer_len = total_len;
cp->io_flags = IOACCEL1_IOFLAGS_IO_REQ |
- (cmd->cmd_len & IOACCEL1_IOFLAGS_CDBLEN_MASK);
+ (cdb_len & IOACCEL1_IOFLAGS_CDBLEN_MASK);
cp->control = control;
- memcpy(cp->CDB, cmd->cmnd, cmd->cmd_len);
- memcpy(cp->CISS_LUN, dev->scsi3addr, 8);
+ memcpy(cp->CDB, cdb, cdb_len);
+ memcpy(cp->CISS_LUN, scsi3addr, 8);
/* Tell the controller to post the reply to the queue for this
* processor. This seems to give the best I/O throughput.
@@ -2274,15 +2522,214 @@
*/
c->busaddr |= 1 | (h->ioaccel1_blockFetchTable[use_sg] << 1) |
IOACCEL1_BUSADDR_CMDTYPE;
-
- /* execute command (bypassing cmd queue if possible) */
- if (unlikely(h->access.fifo_full(h)))
- enqueue_cmd_and_start_io(h, c);
- else
- h->access.submit_command(h, c);
+ enqueue_cmd_and_start_io(h, c);
return 0;
}
+/*
+ * Queue a command directly to a device behind the controller using the
+ * I/O accelerator path.
+ */
+static int hpsa_scsi_ioaccel_direct_map(struct ctlr_info *h,
+ struct CommandList *c)
+{
+ struct scsi_cmnd *cmd = c->scsi_cmd;
+ struct hpsa_scsi_dev_t *dev = cmd->device->hostdata;
+
+ return hpsa_scsi_ioaccel_queue_command(h, c, dev->ioaccel_handle,
+ cmd->cmnd, cmd->cmd_len, dev->scsi3addr);
+}
+
+/*
+ * Attempt to perform offload RAID mapping for a logical volume I/O.
+ */
+static int hpsa_scsi_ioaccel_raid_map(struct ctlr_info *h,
+ struct CommandList *c)
+{
+ struct scsi_cmnd *cmd = c->scsi_cmd;
+ struct hpsa_scsi_dev_t *dev = cmd->device->hostdata;
+ struct raid_map_data *map = &dev->raid_map;
+ struct raid_map_disk_data *dd = &map->data[0];
+ int is_write = 0;
+ u32 map_index;
+ u64 first_block, last_block;
+ u32 block_cnt;
+ u32 blocks_per_row;
+ u64 first_row, last_row;
+ u32 first_row_offset, last_row_offset;
+ u32 first_column, last_column;
+ u32 map_row;
+ u32 disk_handle;
+ u64 disk_block;
+ u32 disk_block_cnt;
+ u8 cdb[16];
+ u8 cdb_len;
+#if BITS_PER_LONG == 32
+ u64 tmpdiv;
+#endif
+
+ BUG_ON(!(dev->offload_config && dev->offload_enabled));
+
+ /* check for valid opcode, get LBA and block count */
+ switch (cmd->cmnd[0]) {
+ case WRITE_6:
+ is_write = 1;
+ case READ_6:
+ first_block =
+ (((u64) cmd->cmnd[2]) << 8) |
+ cmd->cmnd[3];
+ block_cnt = cmd->cmnd[4];
+ break;
+ case WRITE_10:
+ is_write = 1;
+ case READ_10:
+ first_block =
+ (((u64) cmd->cmnd[2]) << 24) |
+ (((u64) cmd->cmnd[3]) << 16) |
+ (((u64) cmd->cmnd[4]) << 8) |
+ cmd->cmnd[5];
+ block_cnt =
+ (((u32) cmd->cmnd[7]) << 8) |
+ cmd->cmnd[8];
+ break;
+ case WRITE_12:
+ is_write = 1;
+ case READ_12:
+ first_block =
+ (((u64) cmd->cmnd[2]) << 24) |
+ (((u64) cmd->cmnd[3]) << 16) |
+ (((u64) cmd->cmnd[4]) << 8) |
+ cmd->cmnd[5];
+ block_cnt =
+ (((u32) cmd->cmnd[6]) << 24) |
+ (((u32) cmd->cmnd[7]) << 16) |
+ (((u32) cmd->cmnd[8]) << 8) |
+ cmd->cmnd[9];
+ break;
+ case WRITE_16:
+ is_write = 1;
+ case READ_16:
+ first_block =
+ (((u64) cmd->cmnd[2]) << 56) |
+ (((u64) cmd->cmnd[3]) << 48) |
+ (((u64) cmd->cmnd[4]) << 40) |
+ (((u64) cmd->cmnd[5]) << 32) |
+ (((u64) cmd->cmnd[6]) << 24) |
+ (((u64) cmd->cmnd[7]) << 16) |
+ (((u64) cmd->cmnd[8]) << 8) |
+ cmd->cmnd[9];
+ block_cnt =
+ (((u32) cmd->cmnd[10]) << 24) |
+ (((u32) cmd->cmnd[11]) << 16) |
+ (((u32) cmd->cmnd[12]) << 8) |
+ cmd->cmnd[13];
+ break;
+ default:
+ return IO_ACCEL_INELIGIBLE; /* process via normal I/O path */
+ }
+ BUG_ON(block_cnt == 0);
+ last_block = first_block + block_cnt - 1;
+
+ /* check for write to non-RAID-0 */
+ if (is_write && dev->raid_level != 0)
+ return IO_ACCEL_INELIGIBLE;
+
+ /* check for invalid block or wraparound */
+ if (last_block >= map->volume_blk_cnt || last_block < first_block)
+ return IO_ACCEL_INELIGIBLE;
+
+ /* calculate stripe information for the request */
+ blocks_per_row = map->data_disks_per_row * map->strip_size;
+#if BITS_PER_LONG == 32
+ tmpdiv = first_block;
+ (void) do_div(tmpdiv, blocks_per_row);
+ first_row = tmpdiv;
+ tmpdiv = last_block;
+ (void) do_div(tmpdiv, blocks_per_row);
+ last_row = tmpdiv;
+ first_row_offset = (u32) (first_block - (first_row * blocks_per_row));
+ last_row_offset = (u32) (last_block - (last_row * blocks_per_row));
+ tmpdiv = first_row_offset;
+ (void) do_div(tmpdiv, map->strip_size);
+ first_column = tmpdiv;
+ tmpdiv = last_row_offset;
+ (void) do_div(tmpdiv, map->strip_size);
+ last_column = tmpdiv;
+#else
+ first_row = first_block / blocks_per_row;
+ last_row = last_block / blocks_per_row;
+ first_row_offset = (u32) (first_block - (first_row * blocks_per_row));
+ last_row_offset = (u32) (last_block - (last_row * blocks_per_row));
+ first_column = first_row_offset / map->strip_size;
+ last_column = last_row_offset / map->strip_size;
+#endif
+
+ /* if this isn't a single row/column then give to the controller */
+ if ((first_row != last_row) || (first_column != last_column))
+ return IO_ACCEL_INELIGIBLE;
+
+ /* proceeding with driver mapping */
+ map_row = ((u32)(first_row >> map->parity_rotation_shift)) %
+ map->row_cnt;
+ map_index = (map_row * (map->data_disks_per_row +
+ map->metadata_disks_per_row)) + first_column;
+ if (dev->raid_level == 2) {
+ /* simple round-robin balancing of RAID 1+0 reads across
+ * primary and mirror members. this is appropriate for SSD
+ * but not optimal for HDD.
+ */
+ if (dev->offload_to_mirror)
+ map_index += map->data_disks_per_row;
+ dev->offload_to_mirror = !dev->offload_to_mirror;
+ }
+ disk_handle = dd[map_index].ioaccel_handle;
+ disk_block = map->disk_starting_blk + (first_row * map->strip_size) +
+ (first_row_offset - (first_column * map->strip_size));
+ disk_block_cnt = block_cnt;
+
+ /* handle differing logical/physical block sizes */
+ if (map->phys_blk_shift) {
+ disk_block <<= map->phys_blk_shift;
+ disk_block_cnt <<= map->phys_blk_shift;
+ }
+ BUG_ON(disk_block_cnt > 0xffff);
+
+ /* build the new CDB for the physical disk I/O */
+ if (disk_block > 0xffffffff) {
+ cdb[0] = is_write ? WRITE_16 : READ_16;
+ cdb[1] = 0;
+ cdb[2] = (u8) (disk_block >> 56);
+ cdb[3] = (u8) (disk_block >> 48);
+ cdb[4] = (u8) (disk_block >> 40);
+ cdb[5] = (u8) (disk_block >> 32);
+ cdb[6] = (u8) (disk_block >> 24);
+ cdb[7] = (u8) (disk_block >> 16);
+ cdb[8] = (u8) (disk_block >> 8);
+ cdb[9] = (u8) (disk_block);
+ cdb[10] = (u8) (disk_block_cnt >> 24);
+ cdb[11] = (u8) (disk_block_cnt >> 16);
+ cdb[12] = (u8) (disk_block_cnt >> 8);
+ cdb[13] = (u8) (disk_block_cnt);
+ cdb[14] = 0;
+ cdb[15] = 0;
+ cdb_len = 16;
+ } else {
+ cdb[0] = is_write ? WRITE_10 : READ_10;
+ cdb[1] = 0;
+ cdb[2] = (u8) (disk_block >> 24);
+ cdb[3] = (u8) (disk_block >> 16);
+ cdb[4] = (u8) (disk_block >> 8);
+ cdb[5] = (u8) (disk_block);
+ cdb[6] = 0;
+ cdb[7] = (u8) (disk_block_cnt >> 8);
+ cdb[8] = (u8) (disk_block_cnt);
+ cdb[9] = 0;
+ cdb_len = 10;
+ }
+ return hpsa_scsi_ioaccel_queue_command(h, c, disk_handle, cdb, cdb_len,
+ dev->scsi3addr);
+}
+
static int hpsa_scsi_queue_command_lck(struct scsi_cmnd *cmd,
void (*done)(struct scsi_cmnd *))
{
@@ -2291,6 +2738,7 @@
unsigned char scsi3addr[8];
struct CommandList *c;
unsigned long flags;
+ int rc = 0;
/* Get the ptr to our adapter structure out of cmd->host. */
h = sdev_to_hba(cmd->device);
@@ -2326,13 +2774,29 @@
c->cmd_type = CMD_SCSI;
c->scsi_cmd = cmd;
- /* Call alternate submit routine for I/O accelerated commands */
- if ((likely(h->transMethod & CFGTBL_Trans_io_accel1)) &&
- (dev->ioaccel_handle) &&
- ((cmd->cmnd[0] == READ_10) || (cmd->cmnd[0] == WRITE_10)) &&
- (scsi_sg_count(cmd) <= IOACCEL1_MAXSGENTRIES) &&
- likely(cmd->request->cmd_type == REQ_TYPE_FS))
- return hpsa_scsi_ioaccel_queue_command(h, c);
+ /* Call alternate submit routine for I/O accelerated commands.
+ * Retries always go down the normal I/O path.
+ */
+ if (likely(cmd->retries == 0 &&
+ cmd->request->cmd_type == REQ_TYPE_FS)) {
+ if (dev->offload_enabled) {
+ rc = hpsa_scsi_ioaccel_raid_map(h, c);
+ if (rc == 0)
+ return 0; /* Sent on ioaccel path */
+ if (rc < 0) { /* scsi_dma_map failed. */
+ cmd_free(h, c);
+ return SCSI_MLQUEUE_HOST_BUSY;
+ }
+ } else if (dev->ioaccel_handle) {
+ rc = hpsa_scsi_ioaccel_direct_map(h, c);
+ if (rc == 0)
+ return 0; /* Sent on direct map path */
+ if (rc < 0) { /* scsi_dma_map failed. */
+ cmd_free(h, c);
+ return SCSI_MLQUEUE_HOST_BUSY;
+ }
+ }
+ }
c->Header.ReplyQueue = 0; /* unused in simple mode */
memcpy(&c->Header.LUN.LunAddrBytes[0], &scsi3addr[0], 8);
@@ -3515,6 +3979,18 @@
c->Request.Type.Direction = XFER_NONE;
c->Request.Timeout = 0;
break;
+ case HPSA_GET_RAID_MAP:
+ c->Request.CDBLen = 12;
+ c->Request.Type.Attribute = ATTR_SIMPLE;
+ c->Request.Type.Direction = XFER_READ;
+ c->Request.Timeout = 0;
+ c->Request.CDB[0] = HPSA_CISS_READ;
+ c->Request.CDB[1] = cmd;
+ c->Request.CDB[6] = (size >> 24) & 0xFF; /* MSB */
+ c->Request.CDB[7] = (size >> 16) & 0xFF;
+ c->Request.CDB[8] = (size >> 8) & 0xFF;
+ c->Request.CDB[9] = size & 0xFF;
+ break;
default:
dev_warn(&h->pdev->dev, "unknown command 0x%c\n", cmd);
BUG();
@@ -4485,6 +4961,7 @@
hpsa_get_max_perf_mode_cmds(h);
h->nr_cmds = h->max_commands - 4; /* Allow room for some ioctls */
h->maxsgentries = readl(&(h->cfgtable->MaxScatterGatherElements));
+ h->fw_support = readl(&(h->cfgtable->misc_fw_support));
/*
* Limit in-command s/g elements to 32 save dma'able memory.
* Howvever spec says if 0, use 31
@@ -4569,18 +5046,19 @@
return -ENOTSUPP;
h->max_commands = readl(&(h->cfgtable->CmdsOutMax));
+
/* Update the field, and then ring the doorbell */
writel(CFGTBL_Trans_Simple, &(h->cfgtable->HostWrite.TransportRequest));
writel(CFGTBL_ChangeReq, h->vaddr + SA5_DOORBELL);
hpsa_wait_for_mode_change_ack(h);
print_cfg_table(&h->pdev->dev, h->cfgtable);
- if (!(readl(&(h->cfgtable->TransportActive)) & CFGTBL_Trans_Simple)) {
- dev_warn(&h->pdev->dev,
- "unable to get board into simple mode\n");
- return -ENODEV;
- }
+ if (!(readl(&(h->cfgtable->TransportActive)) & CFGTBL_Trans_Simple))
+ goto error;
h->transMethod = CFGTBL_Trans_Simple;
return 0;
+error:
+ dev_warn(&h->pdev->dev, "unable to get board into simple mode\n");
+ return -ENODEV;
}
static int hpsa_pci_init(struct ctlr_info *h)
@@ -4961,7 +5439,7 @@
* the 5 lower bits of the address are used by the hardware. and by
* the driver. See comments in hpsa.h for more info.
*/
-#define COMMANDLIST_ALIGNMENT 32
+#define COMMANDLIST_ALIGNMENT 128
BUILD_BUG_ON(sizeof(struct CommandList) % COMMANDLIST_ALIGNMENT);
h = kzalloc(sizeof(*h), GFP_KERNEL);
if (!h)
@@ -5338,8 +5816,8 @@
h->reply_queue[i].current_entry =
readl(h->vaddr + IOACCEL_MODE1_PRODUCER_INDEX);
}
- bft[7] = IOACCEL1_MAXSGENTRIES + 8;
- calc_bucket_map(bft, ARRAY_SIZE(bft), IOACCEL1_MAXSGENTRIES, 8,
+ bft[7] = h->ioaccel_maxsg + 8;
+ calc_bucket_map(bft, ARRAY_SIZE(bft), h->ioaccel_maxsg, 8,
h->ioaccel1_blockFetchTable);
/* initialize all reply queue entries to unused */
@@ -5370,6 +5848,11 @@
static int hpsa_alloc_ioaccel_cmd_and_bft(struct ctlr_info *h)
{
+ h->ioaccel_maxsg =
+ readl(&(h->cfgtable->io_accel_max_embedded_sg_count));
+ if (h->ioaccel_maxsg > IOACCEL1_MAXSGENTRIES)
+ h->ioaccel_maxsg = IOACCEL1_MAXSGENTRIES;
+
/* Command structures must be aligned on a 128-byte boundary
* because the 7 lower bits of the address are used by the
* hardware.
@@ -5383,7 +5866,7 @@
&(h->ioaccel_cmd_pool_dhandle));
h->ioaccel1_blockFetchTable =
- kmalloc(((IOACCEL1_MAXSGENTRIES + 1) *
+ kmalloc(((h->ioaccel_maxsg + 1) *
sizeof(u32)), GFP_KERNEL);
if ((h->ioaccel_cmd_pool == NULL) ||
diff --git a/drivers/scsi/hpsa.h b/drivers/scsi/hpsa.h
index c7865f3..ae08f1c 100644
--- a/drivers/scsi/hpsa.h
+++ b/drivers/scsi/hpsa.h
@@ -47,6 +47,13 @@
unsigned char model[16]; /* bytes 16-31 of inquiry data */
unsigned char raid_level; /* from inquiry page 0xC1 */
u32 ioaccel_handle;
+ int offload_config; /* I/O accel RAID offload configured */
+ int offload_enabled; /* I/O accel RAID offload enabled */
+ int offload_to_mirror; /* Send next I/O accelerator RAID
+ * offload request to mirror drive
+ */
+ struct raid_map_data raid_map; /* I/O accelerator RAID map */
+
};
struct reply_pool {
@@ -133,6 +140,10 @@
u32 *blockFetchTable;
u32 *ioaccel1_blockFetchTable;
unsigned char *hba_inquiry_data;
+ u32 driver_support;
+ u32 fw_support;
+ int ioaccel_support;
+ int ioaccel_maxsg;
u64 last_intr_timestamp;
u32 last_heartbeat;
u64 last_heartbeat_timestamp;
@@ -406,8 +417,7 @@
#define IOACCEL_MODE1_CONSUMER_INDEX 0x1BC
#define IOACCEL_MODE1_REPLY_UNUSED 0xFFFFFFFFFFFFFFFFULL
-static unsigned long SA5_ioaccel_mode1_completed(struct ctlr_info *h,
- u8 q)
+static unsigned long SA5_ioaccel_mode1_completed(struct ctlr_info *h, u8 q)
{
u64 register_value;
struct reply_pool *rq = &h->reply_queue[q];
@@ -420,12 +430,18 @@
rq->head[rq->current_entry] = IOACCEL_MODE1_REPLY_UNUSED;
if (++rq->current_entry == rq->size)
rq->current_entry = 0;
+ /*
+ * @todo
+ *
+ * Don't really need to write the new index after each command,
+ * but with current driver design this is easiest.
+ */
+ wmb();
+ writel((q << 24) | rq->current_entry, h->vaddr +
+ IOACCEL_MODE1_CONSUMER_INDEX);
spin_lock_irqsave(&h->lock, flags);
h->commands_outstanding--;
spin_unlock_irqrestore(&h->lock, flags);
- } else {
- writel((q << 24) | rq->current_entry,
- h->vaddr + IOACCEL_MODE1_CONSUMER_INDEX);
}
return (unsigned long) register_value;
}
diff --git a/drivers/scsi/hpsa_cmd.h b/drivers/scsi/hpsa_cmd.h
index e682d2e..c1ae8d2 100644
--- a/drivers/scsi/hpsa_cmd.h
+++ b/drivers/scsi/hpsa_cmd.h
@@ -42,6 +42,8 @@
#define CMD_UNSOLICITED_ABORT 0x000A
#define CMD_TIMEOUT 0x000B
#define CMD_UNABORTABLE 0x000C
+#define CMD_IOACCEL_DISABLED 0x000E
+
/* Unit Attentions ASC's as defined for the MSA2012sa */
#define POWER_OR_RESET 0x29
@@ -137,6 +139,11 @@
#define CFGTBL_BusType_Ultra3 0x00000002l
#define CFGTBL_BusType_Fibre1G 0x00000100l
#define CFGTBL_BusType_Fibre2G 0x00000200l
+
+/* VPD Inquiry types */
+#define HPSA_VPD_LV_DEVICE_GEOMETRY 0xC1
+#define HPSA_VPD_LV_IOACCEL_STATUS 0xC2
+
struct vals32 {
u32 lower;
u32 upper;
@@ -165,9 +172,46 @@
#define HPSA_REPORT_LOG 0xc2 /* Report Logical LUNs */
#define HPSA_REPORT_PHYS 0xc3 /* Report Physical LUNs */
#define HPSA_REPORT_PHYS_EXTENDED 0x02
+#define HPSA_CISS_READ 0xc0 /* CISS Read */
+#define HPSA_GET_RAID_MAP 0xc8 /* CISS Get RAID Layout Map */
+
+#define RAID_MAP_MAX_ENTRIES 256
+
+struct raid_map_disk_data {
+ u32 ioaccel_handle; /**< Handle to access this disk via the
+ * I/O accelerator */
+ u8 xor_mult[2]; /**< XOR multipliers for this position,
+ * valid for data disks only */
+ u8 reserved[2];
+};
+
+struct raid_map_data {
+ u32 structure_size; /* Size of entire structure in bytes */
+ u32 volume_blk_size; /* bytes / block in the volume */
+ u64 volume_blk_cnt; /* logical blocks on the volume */
+ u8 phys_blk_shift; /* Shift factor to convert between
+ * units of logical blocks and physical
+ * disk blocks */
+ u8 parity_rotation_shift; /* Shift factor to convert between units
+ * of logical stripes and physical
+ * stripes */
+ u16 strip_size; /* blocks used on each disk / stripe */
+ u64 disk_starting_blk; /* First disk block used in volume */
+ u64 disk_blk_cnt; /* disk blocks used by volume / disk */
+ u16 data_disks_per_row; /* data disk entries / row in the map */
+ u16 metadata_disks_per_row; /* mirror/parity disk entries / row
+ * in the map */
+ u16 row_cnt; /* rows in each layout map */
+ u16 layout_map_count; /* layout maps (1 map per mirror/parity
+ * group) */
+ u8 reserved[20];
+ struct raid_map_disk_data data[RAID_MAP_MAX_ENTRIES];
+};
+
struct ReportLUNdata {
u8 LUNListLength[4];
- u32 reserved;
+ u8 extended_response_flag;
+ u8 reserved[3];
u8 LUN[HPSA_MAX_LUN][8];
};
@@ -331,7 +375,7 @@
*/
#define IS_32_BIT ((8 - sizeof(long))/4)
#define IS_64_BIT (!IS_32_BIT)
-#define PAD_32 (4)
+#define PAD_32 (36)
#define PAD_64 (4)
#define COMMANDLIST_PAD (IS_32_BIT * PAD_32 + IS_64_BIT * PAD_64)
u8 pad[COMMANDLIST_PAD];
@@ -371,6 +415,11 @@
struct vals32 host_addr; /* 0x70 - 0x77 */
u8 CISS_LUN[8]; /* 0x78 - 0x7F */
struct SGDescriptor SG[IOACCEL1_MAXSGENTRIES];
+#define IOACCEL1_PAD_64 0
+#define IOACCEL1_PAD_32 0
+#define IOACCEL1_PAD (IS_32_BIT * IOACCEL1_PAD_32 + \
+ IS_64_BIT * IOACCEL1_PAD_64)
+ u8 pad[IOACCEL1_PAD];
};
#define IOACCEL1_FUNCTION_SCSIIO 0x00
@@ -407,6 +456,8 @@
#define MEMQ_MODE 0x08
#define IOACCEL_MODE_1 0x80
+#define DRIVER_SUPPORT_UA_ENABLE 0x00000001
+
struct CfgTable {
u8 Signature[4];
u32 SpecValence;
@@ -435,8 +486,16 @@
u32 misc_fw_support; /* offset 0x78 */
#define MISC_FW_DOORBELL_RESET (0x02)
#define MISC_FW_DOORBELL_RESET2 (0x010)
+#define MISC_FW_RAID_OFFLOAD_BASIC (0x020)
+#define MISC_FW_EVENT_NOTIFY (0x080)
u8 driver_version[32];
-
+ u32 max_cached_write_size;
+ u8 driver_scratchpad[16];
+ u32 max_error_info_length;
+ u32 io_accel_max_embedded_sg_count;
+ u32 io_accel_request_size_offset;
+ u32 event_notify;
+ u32 clear_event_notify;
};
#define NUM_BLOCKFETCH_ENTRIES 8