mtd: replace DEBUG() with pr_debug()
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.
(See Documentation/dynamic-debug-howto.txt)
Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
diff --git a/drivers/mtd/chips/jedec_probe.c b/drivers/mtd/chips/jedec_probe.c
index d40c410..c443f52 100644
--- a/drivers/mtd/chips/jedec_probe.c
+++ b/drivers/mtd/chips/jedec_probe.c
@@ -1917,8 +1917,7 @@
* as they will ignore the writes and don't care what address
* the F0 is written to */
if (cfi->addr_unlock1) {
- DEBUG( MTD_DEBUG_LEVEL3,
- "reset unlock called %x %x \n",
+ pr_debug( "reset unlock called %x %x \n",
cfi->addr_unlock1,cfi->addr_unlock2);
cfi_send_gen_cmd(0xaa, cfi->addr_unlock1, base, map, cfi, cfi->device_type, NULL);
cfi_send_gen_cmd(0x55, cfi->addr_unlock2, base, map, cfi, cfi->device_type, NULL);
@@ -1941,7 +1940,7 @@
uint8_t uaddr;
if (!(jedec_table[index].devtypes & cfi->device_type)) {
- DEBUG(MTD_DEBUG_LEVEL1, "Rejecting potential %s with incompatible %d-bit device type\n",
+ pr_debug("Rejecting potential %s with incompatible %d-bit device type\n",
jedec_table[index].name, 4 * (1<<cfi->device_type));
return 0;
}
@@ -2021,7 +2020,7 @@
* there aren't.
*/
if (finfo->dev_id > 0xff) {
- DEBUG( MTD_DEBUG_LEVEL3, "%s(): ID is not 8bit\n",
+ pr_debug("%s(): ID is not 8bit\n",
__func__);
goto match_done;
}
@@ -2045,12 +2044,10 @@
}
/* the part size must fit in the memory window */
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): Check fit 0x%.8x + 0x%.8x = 0x%.8x\n",
+ pr_debug("MTD %s(): Check fit 0x%.8x + 0x%.8x = 0x%.8x\n",
__func__, base, 1 << finfo->dev_size, base + (1 << finfo->dev_size) );
if ( base + cfi_interleave(cfi) * ( 1 << finfo->dev_size ) > map->size ) {
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): 0x%.4x 0x%.4x %dKiB doesn't fit\n",
+ pr_debug("MTD %s(): 0x%.4x 0x%.4x %dKiB doesn't fit\n",
__func__, finfo->mfr_id, finfo->dev_id,
1 << finfo->dev_size );
goto match_done;
@@ -2061,13 +2058,12 @@
uaddr = finfo->uaddr;
- DEBUG( MTD_DEBUG_LEVEL3, "MTD %s(): check unlock addrs 0x%.4x 0x%.4x\n",
+ pr_debug("MTD %s(): check unlock addrs 0x%.4x 0x%.4x\n",
__func__, cfi->addr_unlock1, cfi->addr_unlock2 );
if ( MTD_UADDR_UNNECESSARY != uaddr && MTD_UADDR_DONT_CARE != uaddr
&& ( unlock_addrs[uaddr].addr1 / cfi->device_type != cfi->addr_unlock1 ||
unlock_addrs[uaddr].addr2 / cfi->device_type != cfi->addr_unlock2 ) ) {
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): 0x%.4x 0x%.4x did not match\n",
+ pr_debug("MTD %s(): 0x%.4x 0x%.4x did not match\n",
__func__,
unlock_addrs[uaddr].addr1,
unlock_addrs[uaddr].addr2);
@@ -2083,15 +2079,13 @@
* FIXME - write a driver that takes all of the chip info as
* module parameters, doesn't probe but forces a load.
*/
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): check ID's disappear when not in ID mode\n",
+ pr_debug("MTD %s(): check ID's disappear when not in ID mode\n",
__func__ );
jedec_reset( base, map, cfi );
mfr = jedec_read_mfr( map, base, cfi );
id = jedec_read_id( map, base, cfi );
if ( mfr == cfi->mfr && id == cfi->id ) {
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): ID 0x%.2x:0x%.2x did not change after reset:\n"
+ pr_debug("MTD %s(): ID 0x%.2x:0x%.2x did not change after reset:\n"
"You might need to manually specify JEDEC parameters.\n",
__func__, cfi->mfr, cfi->id );
goto match_done;
@@ -2104,7 +2098,7 @@
* Put the device back in ID mode - only need to do this if we
* were truly frobbing a real device.
*/
- DEBUG( MTD_DEBUG_LEVEL3, "MTD %s(): return to ID mode\n", __func__ );
+ pr_debug("MTD %s(): return to ID mode\n", __func__ );
if (cfi->addr_unlock1) {
cfi_send_gen_cmd(0xaa, cfi->addr_unlock1, base, map, cfi, cfi->device_type, NULL);
cfi_send_gen_cmd(0x55, cfi->addr_unlock2, base, map, cfi, cfi->device_type, NULL);
@@ -2167,13 +2161,11 @@
cfi->mfr = jedec_read_mfr(map, base, cfi);
cfi->id = jedec_read_id(map, base, cfi);
- DEBUG(MTD_DEBUG_LEVEL3,
- "Search for id:(%02x %02x) interleave(%d) type(%d)\n",
+ pr_debug("Search for id:(%02x %02x) interleave(%d) type(%d)\n",
cfi->mfr, cfi->id, cfi_interleave(cfi), cfi->device_type);
for (i = 0; i < ARRAY_SIZE(jedec_table); i++) {
if ( jedec_match( base, map, cfi, &jedec_table[i] ) ) {
- DEBUG( MTD_DEBUG_LEVEL3,
- "MTD %s(): matched device 0x%x,0x%x unlock_addrs: 0x%.4x 0x%.4x\n",
+ pr_debug("MTD %s(): matched device 0x%x,0x%x unlock_addrs: 0x%.4x 0x%.4x\n",
__func__, cfi->mfr, cfi->id,
cfi->addr_unlock1, cfi->addr_unlock2 );
if (!cfi_jedec_setup(map, cfi, i))