USB: digi_acceleport: remove bogus disconnect test in close
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index ebe45fa..76a8c20 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -1149,53 +1149,51 @@
if (port->serial->disconnected)
goto exit;
- if (port->serial->dev) {
- /* FIXME: Transmit idle belongs in the wait_unti_sent path */
- digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT);
+ /* FIXME: Transmit idle belongs in the wait_unti_sent path */
+ digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT);
- /* disable input flow control */
- buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
- buf[1] = priv->dp_port_num;
- buf[2] = DIGI_DISABLE;
- buf[3] = 0;
+ /* disable input flow control */
+ buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
+ buf[1] = priv->dp_port_num;
+ buf[2] = DIGI_DISABLE;
+ buf[3] = 0;
- /* disable output flow control */
- buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
- buf[5] = priv->dp_port_num;
- buf[6] = DIGI_DISABLE;
- buf[7] = 0;
+ /* disable output flow control */
+ buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
+ buf[5] = priv->dp_port_num;
+ buf[6] = DIGI_DISABLE;
+ buf[7] = 0;
- /* disable reading modem signals automatically */
- buf[8] = DIGI_CMD_READ_INPUT_SIGNALS;
- buf[9] = priv->dp_port_num;
- buf[10] = DIGI_DISABLE;
- buf[11] = 0;
+ /* disable reading modem signals automatically */
+ buf[8] = DIGI_CMD_READ_INPUT_SIGNALS;
+ buf[9] = priv->dp_port_num;
+ buf[10] = DIGI_DISABLE;
+ buf[11] = 0;
- /* disable receive */
- buf[12] = DIGI_CMD_RECEIVE_ENABLE;
- buf[13] = priv->dp_port_num;
- buf[14] = DIGI_DISABLE;
- buf[15] = 0;
+ /* disable receive */
+ buf[12] = DIGI_CMD_RECEIVE_ENABLE;
+ buf[13] = priv->dp_port_num;
+ buf[14] = DIGI_DISABLE;
+ buf[15] = 0;
- /* flush fifos */
- buf[16] = DIGI_CMD_IFLUSH_FIFO;
- buf[17] = priv->dp_port_num;
- buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
- buf[19] = 0;
+ /* flush fifos */
+ buf[16] = DIGI_CMD_IFLUSH_FIFO;
+ buf[17] = priv->dp_port_num;
+ buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
+ buf[19] = 0;
- ret = digi_write_oob_command(port, buf, 20, 0);
- if (ret != 0)
- dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", ret);
+ ret = digi_write_oob_command(port, buf, 20, 0);
+ if (ret != 0)
+ dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n",
+ ret);
+ /* wait for final commands on oob port to complete */
+ prepare_to_wait(&priv->dp_flush_wait, &wait,
+ TASK_INTERRUPTIBLE);
+ schedule_timeout(DIGI_CLOSE_TIMEOUT);
+ finish_wait(&priv->dp_flush_wait, &wait);
- /* wait for final commands on oob port to complete */
- prepare_to_wait(&priv->dp_flush_wait, &wait,
- TASK_INTERRUPTIBLE);
- schedule_timeout(DIGI_CLOSE_TIMEOUT);
- finish_wait(&priv->dp_flush_wait, &wait);
-
- /* shutdown any outstanding bulk writes */
- usb_kill_urb(port->write_urb);
- }
+ /* shutdown any outstanding bulk writes */
+ usb_kill_urb(port->write_urb);
exit:
spin_lock_irq(&priv->dp_port_lock);
priv->dp_write_urb_in_use = 0;