dmaengine: ste_dma40: Move default memcpy configs into the driver
There are only two default memcpy configurations used for the DMA40
driver; one for physical memcpy and one for logical memcpy. Instead
of invariably passing the same configurations though platform data,
we're moving them into the driver instead.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index cd7b480..c47139a 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -72,6 +72,34 @@
DB8500_DMA_MEMCPY_EV_5,
};
+/* Default configuration for physcial memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
+ .mode = STEDMA40_MODE_PHYSICAL,
+ .dir = STEDMA40_MEM_TO_MEM,
+
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .src_info.psize = STEDMA40_PSIZE_PHY_1,
+ .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.psize = STEDMA40_PSIZE_PHY_1,
+ .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
+
+/* Default configuration for logical memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_log = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_MEM,
+
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .src_info.psize = STEDMA40_PSIZE_LOG_1,
+ .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.psize = STEDMA40_PSIZE_LOG_1,
+ .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
+
/**
* enum 40_command - The different commands and/or statuses.
*
@@ -2029,13 +2057,13 @@
dma_cap_mask_t cap = d40c->chan.device->cap_mask;
if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
- d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_log;
+ d40c->dma_cfg = dma40_memcpy_conf_log;
d40c->dma_cfg.src_dev_type = STEDMA40_DEV_SRC_MEMORY;
d40c->dma_cfg.dst_dev_type = dma40_memcpy_channels[d40c->chan.chan_id];
} else if (dma_has_cap(DMA_MEMCPY, cap) &&
dma_has_cap(DMA_SLAVE, cap)) {
- d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_phy;
+ d40c->dma_cfg = dma40_memcpy_conf_phy;
} else {
chan_err(d40c, "No memcpy\n");
return -EINVAL;