| # |
| # Multifunction miscellaneous devices |
| # |
| |
| if HAS_IOMEM |
| menu "Multifunction device drivers" |
| |
| config MFD_CORE |
| tristate |
| select IRQ_DOMAIN |
| default n |
| |
| config MFD_CS5535 |
| tristate "AMD CS5535 and CS5536 southbridge core functions" |
| select MFD_CORE |
| depends on PCI && (X86_32 || (X86 && COMPILE_TEST)) |
| ---help--- |
| This is the core driver for CS5535/CS5536 MFD functions. This is |
| necessary for using the board's GPIO and MFGPT functionality. |
| |
| config MFD_AS3711 |
| bool "AMS AS3711" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C=y |
| help |
| Support for the AS3711 PMIC from AMS |
| |
| config MFD_AS3722 |
| bool "ams AS3722 Power Management IC" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C=y && OF |
| help |
| The ams AS3722 is a compact system PMU suitable for mobile phones, |
| tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down |
| controllers, 11 LDOs, RTC, automatic battery, temperature and |
| over current monitoring, GPIOs, ADC and a watchdog. |
| |
| config PMIC_ADP5520 |
| bool "Analog Devices ADP5520/01 MFD PMIC Core Support" |
| depends on I2C=y |
| help |
| Say yes here to add support for Analog Devices AD5520 and ADP5501, |
| Multifunction Power Management IC. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, LEDs, GPIOs and Kepad |
| under the corresponding menus. |
| |
| config MFD_AAT2870_CORE |
| bool "AnalogicTech AAT2870" |
| select MFD_CORE |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the AAT2870. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_ATMEL_HLCDC |
| tristate "Atmel HLCDC (High-end LCD Controller)" |
| select MFD_CORE |
| select REGMAP_MMIO |
| depends on OF |
| help |
| If you say yes here you get support for the HLCDC block. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_BCM590XX |
| tristate "Broadcom BCM590xx PMUs" |
| select MFD_CORE |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Support for the BCM590xx PMUs from Broadcom |
| |
| config MFD_AXP20X |
| bool "X-Powers AXP20X" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C=y |
| help |
| If you say Y here you get support for the X-Powers AXP202, AXP209 and |
| AXP288 power management IC (PMIC). |
| This driver include only the core APIs. You have to select individual |
| components like regulators or the PEK (Power Enable Key) under the |
| corresponding menus. |
| |
| config MFD_CROS_EC |
| tristate "ChromeOS Embedded Controller" |
| select MFD_CORE |
| help |
| If you say Y here you get support for the ChromeOS Embedded |
| Controller (EC) providing keyboard, battery and power services. |
| You also need to enable the driver for the bus you are using. The |
| protocol for talking to the EC is defined by the bus driver. |
| |
| config MFD_CROS_EC_I2C |
| tristate "ChromeOS Embedded Controller (I2C)" |
| depends on MFD_CROS_EC && I2C |
| |
| help |
| If you say Y here, you get support for talking to the ChromeOS |
| EC through an I2C bus. This uses a simple byte-level protocol with |
| a checksum. Failing accesses will be retried three times to |
| improve reliability. |
| |
| config MFD_CROS_EC_SPI |
| tristate "ChromeOS Embedded Controller (SPI)" |
| depends on MFD_CROS_EC && SPI && OF |
| |
| ---help--- |
| If you say Y here, you get support for talking to the ChromeOS EC |
| through a SPI bus, using a byte-level protocol. Since the EC's |
| response time cannot be guaranteed, we support ignoring |
| 'pre-amble' bytes before the response actually starts. |
| |
| config MFD_ASIC3 |
| bool "Compaq ASIC3" |
| depends on GPIOLIB && ARM |
| select MFD_CORE |
| ---help--- |
| This driver supports the ASIC3 multifunction chip found on many |
| PDAs (mainly iPAQ and HTC based ones) |
| |
| config PMIC_DA903X |
| bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" |
| depends on I2C=y |
| help |
| Say yes here to add support for Dialog Semiconductor DA9030 (a.k.a |
| ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC |
| usually found on PXA processors-based platforms. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, voltage regulators, |
| LEDs and battery-charger under the corresponding menus. |
| |
| config PMIC_DA9052 |
| bool |
| select MFD_CORE |
| |
| config MFD_DA9052_SPI |
| bool "Dialog Semiconductor DA9052/53 PMIC variants with SPI" |
| select REGMAP_SPI |
| select REGMAP_IRQ |
| select PMIC_DA9052 |
| depends on SPI_MASTER=y |
| help |
| Support for the Dialog Semiconductor DA9052 PMIC |
| when controlled using SPI. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_DA9052_I2C |
| bool "Dialog Semiconductor DA9052/53 PMIC variants with I2C" |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select PMIC_DA9052 |
| depends on I2C=y |
| help |
| Support for the Dialog Semiconductor DA9052 PMIC |
| when controlled using I2C. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_DA9055 |
| bool "Dialog Semiconductor DA9055 PMIC Support" |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select MFD_CORE |
| depends on I2C=y |
| help |
| Say yes here for support of Dialog Semiconductor DA9055. This is |
| a Power Management IC. This driver provides common support for |
| accessing the device as well as the I2C interface to the chip itself. |
| Additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| This driver can be built as a module. If built as a module it will be |
| called "da9055" |
| |
| config MFD_DA9063 |
| bool "Dialog Semiconductor DA9063 PMIC Support" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C=y |
| help |
| Say yes here for support for the Dialog Semiconductor DA9063 PMIC. |
| This includes the I2C driver and core APIs. |
| Additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_DLN2 |
| tristate "Diolan DLN2 support" |
| select MFD_CORE |
| depends on USB |
| help |
| This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter |
| DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2, |
| etc. must be enabled in order to use the functionality of |
| the device. |
| |
| config MFD_MC13XXX |
| tristate |
| depends on (SPI_MASTER || I2C) |
| select MFD_CORE |
| select REGMAP_IRQ |
| help |
| Enable support for the Freescale MC13783 and MC13892 PMICs. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_MC13XXX_SPI |
| tristate "Freescale MC13783 and MC13892 SPI interface" |
| depends on SPI_MASTER |
| select REGMAP_SPI |
| select MFD_MC13XXX |
| help |
| Select this if your MC13xxx is connected via an SPI bus. |
| |
| config MFD_MC13XXX_I2C |
| tristate "Freescale MC13892 I2C interface" |
| depends on I2C |
| select REGMAP_I2C |
| select MFD_MC13XXX |
| help |
| Select this if your MC13xxx is connected via an I2C bus. |
| |
| config MFD_HI6421_PMIC |
| tristate "HiSilicon Hi6421 PMU/Codec IC" |
| depends on OF |
| select MFD_CORE |
| select REGMAP_MMIO |
| help |
| Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- |
| functions, such as regulators, RTC, codec, Coulomb counter, etc. |
| This driver includes core APIs _only_. You have to select |
| individul components like voltage regulators under corresponding |
| menus in order to enable them. |
| We communicate with the Hi6421 via memory-mapped I/O. |
| |
| config HTC_EGPIO |
| bool "HTC EGPIO support" |
| depends on GPIOLIB && ARM |
| help |
| This driver supports the CPLD egpio chip present on |
| several HTC phones. It provides basic support for input |
| pins, output pins, and irqs. |
| |
| config HTC_PASIC3 |
| tristate "HTC PASIC3 LED/DS1WM chip support" |
| select MFD_CORE |
| help |
| This core driver provides register access for the LED/DS1WM |
| chips labeled "AIC2" and "AIC3", found on HTC Blueangel and |
| HTC Magician devices, respectively. Actual functionality is |
| handled by the leds-pasic3 and ds1wm drivers. |
| |
| config HTC_I2CPLD |
| bool "HTC I2C PLD chip support" |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the supposed CPLD |
| found on omap850 HTC devices like the HTC Wizard and HTC Herald. |
| This device provides input and output GPIOs through an I2C |
| interface to one or more sub-chips. |
| |
| config LPC_ICH |
| tristate "Intel ICH LPC" |
| depends on PCI |
| select MFD_CORE |
| help |
| The LPC bridge function of the Intel ICH provides support for |
| many functional units. This driver provides needed support for |
| other drivers to control these functions, currently GPIO and |
| watchdog. |
| |
| config LPC_SCH |
| tristate "Intel SCH LPC" |
| depends on PCI |
| select MFD_CORE |
| help |
| LPC bridge function of the Intel SCH provides support for |
| System Management Bus and General Purpose I/O. |
| |
| config INTEL_SOC_PMIC |
| bool "Support for Intel Atom SoC PMIC" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| Select this option to enable support for the PMIC device |
| on some Intel SoC systems. The PMIC provides ADC, GPIO, |
| thermal, charger and related power management functions |
| on these systems. |
| |
| config MFD_INTEL_MSIC |
| bool "Intel MSIC" |
| depends on INTEL_SCU_IPC |
| select MFD_CORE |
| help |
| Select this option to enable access to Intel MSIC (Avatele |
| Passage) chip. This chip embeds audio, battery, GPIO, etc. |
| devices used in Intel Medfield platforms. |
| |
| config MFD_IPAQ_MICRO |
| bool "Atmel Micro ASIC (iPAQ h3100/h3600/h3700) Support" |
| depends on SA1100_H3100 || SA1100_H3600 |
| select MFD_CORE |
| help |
| Select this to get support for the Microcontroller found in |
| the Compaq iPAQ handheld computers. This is an Atmel |
| AT90LS8535 microcontroller flashed with a special iPAQ |
| firmware using the custom protocol implemented in this driver. |
| |
| config MFD_JANZ_CMODIO |
| tristate "Janz CMOD-IO PCI MODULbus Carrier Board" |
| select MFD_CORE |
| depends on PCI |
| help |
| This is the core driver for the Janz CMOD-IO PCI MODULbus |
| carrier board. This device is a PCI to MODULbus bridge which may |
| host many different types of MODULbus daughterboards, including |
| CAN and GPIO controllers. |
| |
| config MFD_JZ4740_ADC |
| bool "Janz JZ4740 ADC core" |
| select MFD_CORE |
| select GENERIC_IRQ_CHIP |
| depends on MACH_JZ4740 |
| help |
| Say yes here if you want support for the ADC unit in the JZ4740 SoC. |
| This driver is necessary for jz4740-battery and jz4740-hwmon driver. |
| |
| config MFD_KEMPLD |
| tristate "Kontron module PLD device" |
| select MFD_CORE |
| help |
| This is the core driver for the PLD (Programmable Logic Device) found |
| on some Kontron ETX and COMexpress (ETXexpress) modules. The PLD |
| device may provide functions like watchdog, GPIO, UART and I2C bus. |
| |
| The following modules are supported: |
| * COMe-bHL6 |
| * COMe-bIP# |
| * COMe-bPC2 (ETXexpress-PC) |
| * COMe-bSC# (ETXexpress-SC T#) |
| * COMe-cBT6 |
| * COMe-cCT6 |
| * COMe-cDC2 (microETXexpress-DC) |
| * COMe-cHL6 |
| * COMe-cPC2 (microETXexpress-PC) |
| * COMe-mBT10 |
| * COMe-mCT10 |
| * COMe-mTT10 (nanoETXexpress-TT) |
| * ETX-OH |
| |
| This driver can also be built as a module. If so, the module |
| will be called kempld-core. |
| |
| config MFD_88PM800 |
| tristate "Marvell 88PM800" |
| depends on I2C=y |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select MFD_CORE |
| help |
| This supports for Marvell 88PM800 Power Management IC. |
| This includes the I2C driver and the core APIs _only_, you have to |
| select individual components like voltage regulators, RTC and |
| battery-charger under the corresponding menus. |
| |
| config MFD_88PM805 |
| tristate "Marvell 88PM805" |
| depends on I2C=y |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select MFD_CORE |
| help |
| This supports for Marvell 88PM805 Power Management IC. This includes |
| the I2C driver and the core APIs _only_, you have to select individual |
| components like codec device, headset/Mic device under the |
| corresponding menus. |
| |
| config MFD_88PM860X |
| bool "Marvell 88PM8606/88PM8607" |
| depends on I2C=y |
| select REGMAP_I2C |
| select MFD_CORE |
| help |
| This supports for Marvell 88PM8606/88PM8607 Power Management IC. |
| This includes the I2C driver and the core APIs _only_, you have to |
| select individual components like voltage regulators, RTC and |
| battery-charger under the corresponding menus. |
| |
| config MFD_MAX14577 |
| bool "Maxim Semiconductor MAX14577/77836 MUIC + Charger Support" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select IRQ_DOMAIN |
| help |
| Say yes here to add support for Maxim Semiconductor MAX14577 and |
| MAX77836 Micro-USB ICs with battery charger. |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MAX77686 |
| bool "Maxim Semiconductor MAX77686/802 PMIC Support" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select IRQ_DOMAIN |
| help |
| Say yes here to add support for Maxim Semiconductor MAX77686 and |
| MAX77802 which are Power Management IC with an RTC on chip. |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MAX77693 |
| bool "Maxim Semiconductor MAX77693 PMIC Support" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| Say yes here to add support for Maxim Semiconductor MAX77693. |
| This is a companion Power Management IC with Flash, Haptic, Charger, |
| and MUIC(Micro USB Interface Controller) controls on chip. |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MAX8907 |
| tristate "Maxim Semiconductor MAX8907 PMIC Support" |
| select MFD_CORE |
| depends on I2C=y |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| Say yes here to add support for Maxim Semiconductor MAX8907. This is |
| a Power Management IC. This driver provides common support for |
| accessing the device; additional drivers must be enabled in order |
| to use the functionality of the device. |
| |
| config MFD_MAX8925 |
| bool "Maxim Semiconductor MAX8925 PMIC Support" |
| depends on I2C=y |
| select MFD_CORE |
| help |
| Say yes here to add support for Maxim Semiconductor MAX8925. This is |
| a Power Management IC. This driver provides common support for |
| accessing the device, additional drivers must be enabled in order |
| to use the functionality of the device. |
| |
| config MFD_MAX8997 |
| bool "Maxim Semiconductor MAX8997/8966 PMIC Support" |
| depends on I2C=y |
| select MFD_CORE |
| select IRQ_DOMAIN |
| help |
| Say yes here to add support for Maxim Semiconductor MAX8997/8966. |
| This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic, |
| MUIC controls on chip. |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MAX8998 |
| bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support" |
| depends on I2C=y |
| select MFD_CORE |
| select IRQ_DOMAIN |
| help |
| Say yes here to add support for Maxim Semiconductor MAX8998 and |
| National Semiconductor LP3974. This is a Power Management IC. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MENF21BMC |
| tristate "MEN 14F021P00 Board Management Controller Support" |
| depends on I2C |
| select MFD_CORE |
| help |
| Say yes here to add support for the MEN 14F021P00 BMC |
| which is a Board Management Controller connected to the I2C bus. |
| The device supports multiple sub-devices like LED, HWMON and WDT. |
| This driver provides common support for accessing the devices; |
| additional drivers must be enabled in order to use the |
| functionality of the BMC device. |
| |
| This driver can also be built as a module. If so the module |
| will be called menf21bmc. |
| |
| config EZX_PCAP |
| bool "Motorola EZXPCAP Support" |
| depends on SPI_MASTER |
| help |
| This enables the PCAP ASIC present on EZX Phones. This is |
| needed for MMC, TouchScreen, Sound, USB, etc.. |
| |
| config MFD_VIPERBOARD |
| tristate "Nano River Technologies Viperboard" |
| select MFD_CORE |
| depends on USB |
| default n |
| help |
| Say yes here if you want support for Nano River Technologies |
| Viperboard. |
| There are mfd cell drivers available for i2c master, adc and |
| both gpios found on the board. The spi part does not yet |
| have a driver. |
| You need to select the mfd cell drivers separately. |
| The drivers do not support all features the board exposes. |
| |
| config MFD_RETU |
| tristate "Nokia Retu and Tahvo multi-function device" |
| select MFD_CORE |
| depends on I2C |
| select REGMAP_IRQ |
| help |
| Retu and Tahvo are a multi-function devices found on Nokia |
| Internet Tablets (770, N800 and N810). |
| |
| config MFD_PCF50633 |
| tristate "NXP PCF50633" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say yes here if you have NXP PCF50633 chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| config PCF50633_ADC |
| tristate "NXP PCF50633 ADC" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support for ADC in the |
| NXP PCF50633 chip. |
| |
| config PCF50633_GPIO |
| tristate "NXP PCF50633 GPIO" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support GPIO for pins on |
| the PCF50633 chip. |
| |
| config UCB1400_CORE |
| tristate "Philips UCB1400 Core driver" |
| depends on AC97_BUS |
| depends on GPIOLIB |
| help |
| This enables support for the Philips UCB1400 core functions. |
| The UCB1400 is an AC97 audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ucb1400_core. |
| |
| config MFD_PM8XXX |
| tristate |
| |
| config MFD_PM8921_CORE |
| tristate "Qualcomm PM8921 PMIC chip" |
| depends on (ARM || HEXAGON) |
| select IRQ_DOMAIN |
| select MFD_CORE |
| select MFD_PM8XXX |
| select REGMAP |
| help |
| If you say yes to this option, support will be included for the |
| built-in PM8921 PMIC chip. |
| |
| This is required if your board has a PM8921 and uses its features, |
| such as: MPPs, GPIOs, regulators, interrupts, and PWM. |
| |
| Say M here if you want to include support for PM8921 chip as a module. |
| This will build a module called "pm8921-core". |
| |
| config MFD_SPMI_PMIC |
| tristate "Qualcomm SPMI PMICs" |
| depends on ARCH_QCOM || COMPILE_TEST |
| depends on OF |
| depends on SPMI |
| select REGMAP_SPMI |
| help |
| This enables support for the Qualcomm SPMI PMICs. |
| These PMICs are currently used with the Snapdragon 800 series of |
| SoCs. Note, that this will only be useful paired with descriptions |
| of the independent functions as children nodes in the device tree. |
| |
| Say M here if you want to include support for the SPMI PMIC |
| series as a module. The module will be called "qcom-spmi-pmic". |
| |
| config MFD_RDC321X |
| tristate "RDC R-321x southbridge" |
| select MFD_CORE |
| depends on PCI |
| help |
| Say yes here if you want to have support for the RDC R-321x SoC |
| southbridge which provides access to GPIOs and Watchdog using the |
| southbridge PCI device configuration space. |
| |
| config MFD_RTSX_PCI |
| tristate "Realtek PCI-E card reader" |
| depends on PCI |
| select MFD_CORE |
| help |
| This supports for Realtek PCI-Express card reader including rts5209, |
| rts5229, rtl8411, etc. Realtek card reader supports access to many |
| types of memory cards, such as Memory Stick, Memory Stick Pro, |
| Secure Digital and MultiMediaCard. |
| |
| config MFD_RTSX_USB |
| tristate "Realtek USB card reader" |
| depends on USB |
| select MFD_CORE |
| help |
| Select this option to get support for Realtek USB 2.0 card readers |
| including RTS5129, RTS5139, RTS5179 and RTS5170. |
| Realtek card reader supports access to many types of memory cards, |
| such as Memory Stick Pro, Secure Digital and MultiMediaCard. |
| |
| config MFD_RC5T583 |
| bool "Ricoh RC5T583 Power Management system device" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| Select this option to get support for the RICOH583 Power |
| Management system device. |
| This driver provides common support for accessing the device |
| through i2c interface. The device supports multiple sub-devices |
| like GPIO, interrupts, RTC, LDO and DCDC regulators, onkey. |
| Additional drivers must be enabled in order to use the |
| different functionality of the device. |
| |
| config MFD_RK808 |
| tristate "Rockchip RK808 Power Management chip" |
| depends on I2C && OF |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the RK808 |
| Power Management chips. |
| This driver provides common support for accessing the device |
| through I2C interface. The device supports multiple sub-devices |
| including interrupts, RTC, LDO & DCDC regulators, and onkey. |
| |
| config MFD_RN5T618 |
| tristate "Ricoh RN5T5618 PMIC" |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| Say yes here to add support for the Ricoh RN5T618 PMIC. This |
| driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_SEC_CORE |
| bool "SAMSUNG Electronics PMIC Series Support" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| Support for the Samsung Electronics MFD series. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the functionality |
| of the device |
| |
| config MFD_SI476X_CORE |
| tristate "Silicon Laboratories 4761/64/68 AM/FM radio." |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| This is the core driver for the SI476x series of AM/FM |
| radio. This MFD driver connects the radio-si476x V4L2 module |
| and the si476x audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called si476x-core. |
| |
| config MFD_SM501 |
| tristate "Silicon Motion SM501" |
| ---help--- |
| This is the core driver for the Silicon Motion SM501 multimedia |
| companion chip. This device is a multifunction device which may |
| provide numerous interfaces including USB host controller, USB gadget, |
| asynchronous serial ports, audio functions, and a dual display video |
| interface. The device may be connected by PCI or local bus with |
| varying functions enabled. |
| |
| config MFD_SM501_GPIO |
| bool "Export GPIO via GPIO layer" |
| depends on MFD_SM501 && GPIOLIB |
| ---help--- |
| This option uses the gpio library layer to export the 64 GPIO |
| lines on the SM501. The platform data is used to supply the |
| base number for the first GPIO line to register. |
| |
| config MFD_SMSC |
| bool "SMSC ECE1099 series chips" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the |
| ece1099 chips from SMSC. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called smsc. |
| |
| config ABX500_CORE |
| bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" |
| default y if ARCH_U300 || ARCH_U8500 |
| help |
| Say yes here if you have the ABX500 Mixed Signal IC family |
| chips. This core driver expose register access functions. |
| Functionality specific drivers using these functions can |
| remain unchanged when IC changes. Binding of the functions to |
| actual register access is done by the IC core driver. |
| |
| config AB3100_CORE |
| bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" |
| depends on I2C=y && ABX500_CORE |
| select MFD_CORE |
| default y if ARCH_U300 |
| help |
| Select this to enable the AB3100 Mixed Signal IC core |
| functionality. This connects to a AB3100 on the I2C bus |
| and expose a number of symbols needed for dependent devices |
| to read and write registers and subscribe to events from |
| this multi-functional IC. This is needed to use other features |
| of the AB3100 such as battery-backed RTC, charging control, |
| LEDs, vibrator, system power and temperature, power management |
| and ALSA sound. |
| |
| config AB3100_OTP |
| tristate "ST-Ericsson AB3100 OTP functions" |
| depends on AB3100_CORE |
| default y if AB3100_CORE |
| help |
| Select this to enable the AB3100 Mixed Signal IC OTP (one-time |
| programmable memory) support. This exposes a sysfs file to read |
| out OTP values. |
| |
| config AB8500_CORE |
| bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" |
| depends on ABX500_CORE && MFD_DB8500_PRCMU |
| select POWER_SUPPLY |
| select MFD_CORE |
| select IRQ_DOMAIN |
| help |
| Select this option to enable access to AB8500 power management |
| chip. This connects to U8500 either on the SSP/SPI bus (deprecated |
| since hardware version v1.0) or the I2C bus via PRCMU. It also adds |
| the irq_chip parts for handling the Mixed Signal chip events. |
| This chip embeds various other multimedia funtionalities as well. |
| |
| config AB8500_DEBUG |
| bool "Enable debug info via debugfs" |
| depends on AB8500_GPADC && DEBUG_FS |
| default y if DEBUG_FS |
| help |
| Select this option if you want debug information using the debug |
| filesystem, debugfs. |
| |
| config AB8500_GPADC |
| bool "ST-Ericsson AB8500 GPADC driver" |
| depends on AB8500_CORE && REGULATOR_AB8500 |
| default y |
| help |
| AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage |
| |
| config MFD_DB8500_PRCMU |
| bool "ST-Ericsson DB8500 Power Reset Control Management Unit" |
| depends on UX500_SOC_DB8500 |
| select MFD_CORE |
| help |
| Select this option to enable support for the DB8500 Power Reset |
| and Control Management Unit. This is basically an autonomous |
| system controller running an XP70 microprocessor, which is accessed |
| through a register map. |
| |
| config MFD_STMPE |
| bool "STMicroelectronics STMPE" |
| depends on (I2C=y || SPI_MASTER=y) |
| depends on OF |
| select MFD_CORE |
| help |
| Support for the STMPE family of I/O Expanders from |
| STMicroelectronics. |
| |
| Currently supported devices are: |
| |
| STMPE811: GPIO, Touchscreen |
| STMPE1601: GPIO, Keypad |
| STMPE1801: GPIO, Keypad |
| STMPE2401: GPIO, Keypad |
| STMPE2403: GPIO, Keypad |
| |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the functionality |
| of the device. Currently available sub drivers are: |
| |
| GPIO: stmpe-gpio |
| Keypad: stmpe-keypad |
| Touchscreen: stmpe-ts |
| |
| menu "STMicroelectronics STMPE Interface Drivers" |
| depends on MFD_STMPE |
| |
| config STMPE_I2C |
| bool "STMicroelectronics STMPE I2C Interface" |
| depends on I2C=y |
| default y |
| help |
| This is used to enable I2C interface of STMPE |
| |
| config STMPE_SPI |
| bool "STMicroelectronics STMPE SPI Interface" |
| depends on SPI_MASTER |
| help |
| This is used to enable SPI interface of STMPE |
| endmenu |
| |
| config MFD_STA2X11 |
| bool "STMicroelectronics STA2X11" |
| depends on STA2X11 |
| select MFD_CORE |
| select REGMAP_MMIO |
| |
| config MFD_SUN6I_PRCM |
| bool "Allwinner A31 PRCM controller" |
| depends on ARCH_SUNXI |
| select MFD_CORE |
| help |
| Support for the PRCM (Power/Reset/Clock Management) unit available |
| in A31 SoC. |
| |
| config MFD_SYSCON |
| bool "System Controller Register R/W Based on Regmap" |
| select REGMAP_MMIO |
| help |
| Select this option to enable accessing system control registers |
| via regmap. |
| |
| config MFD_DAVINCI_VOICECODEC |
| tristate |
| select MFD_CORE |
| select REGMAP_MMIO |
| |
| config MFD_TI_AM335X_TSCADC |
| tristate "TI ADC / Touch Screen chip support" |
| select MFD_CORE |
| select REGMAP |
| select REGMAP_MMIO |
| help |
| If you say yes here you get support for Texas Instruments series |
| of Touch Screen /ADC chips. |
| To compile this driver as a module, choose M here: the |
| module will be called ti_am335x_tscadc. |
| |
| config MFD_DM355EVM_MSP |
| bool "TI DaVinci DM355 EVM microcontroller" |
| depends on I2C=y && MACH_DAVINCI_DM355_EVM |
| help |
| This driver supports the MSP430 microcontroller used on these |
| boards. MSP430 firmware manages resets and power sequencing, |
| inputs from buttons and the IR remote, LEDs, an RTC, and more. |
| |
| config MFD_LP3943 |
| tristate "TI/National Semiconductor LP3943 MFD Driver" |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| Support for the TI/National Semiconductor LP3943. |
| This driver consists of GPIO and PWM drivers. |
| With these functionalities, it can be used for LED string control or |
| general usage such like a GPIO controller and a PWM controller. |
| |
| config MFD_LP8788 |
| bool "TI LP8788 Power Management Unit Driver" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select IRQ_DOMAIN |
| help |
| TI LP8788 PMU supports regulators, battery charger, RTC, |
| ADC, backlight driver and current sinks. |
| |
| config MFD_OMAP_USB_HOST |
| bool "TI OMAP USBHS core and TLL driver" |
| depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 |
| default y |
| help |
| This is the core driver for the OAMP EHCI and OHCI drivers. |
| This MFD driver does the required setup functionalities for |
| OMAP USB Host drivers. |
| |
| config MFD_PALMAS |
| bool "TI Palmas series chips" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C=y |
| help |
| If you say yes here you get support for the Palmas |
| series of PMIC chips from Texas Instruments. |
| |
| config TPS6105X |
| tristate "TI TPS61050/61052 Boost Converters" |
| depends on I2C |
| select REGULATOR |
| select MFD_CORE |
| select REGULATOR_FIXED_VOLTAGE |
| help |
| This option enables a driver for the TP61050/TPS61052 |
| high-power "white LED driver". This boost converter is |
| sometimes used for other things than white LEDs, and |
| also contains a GPIO pin. |
| |
| config TPS65010 |
| tristate "TI TPS6501x Power Management chips" |
| depends on I2C && GPIOLIB |
| default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK |
| help |
| If you say yes here you get support for the TPS6501x series of |
| Power Management chips. These include voltage regulators, |
| lithium ion/polymer battery charging, and other features that |
| are often used in portable devices like cell phones and cameras. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps65010. |
| |
| config TPS6507X |
| tristate "TI TPS6507x Power Management / Touch Screen chips" |
| select MFD_CORE |
| depends on I2C |
| help |
| If you say yes here you get support for the TPS6507x series of |
| Power Management / Touch Screen chips. These include voltage |
| regulators, lithium ion/polymer battery charging, touch screen |
| and other features that are often used in portable devices. |
| This driver can also be built as a module. If so, the module |
| will be called tps6507x. |
| |
| config TPS65911_COMPARATOR |
| tristate |
| |
| config MFD_TPS65090 |
| bool "TI TPS65090 Power Management chips" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the TPS65090 series of |
| Power Management chips. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_TPS65217 |
| tristate "TI TPS65217 Power Management / White LED chips" |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the TPS65217 series of |
| Power Management / White LED chips. |
| These include voltage regulators, lithium ion/polymer battery |
| charger, wled and other features that are often used in portable |
| devices. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps65217. |
| |
| config MFD_TPS65218 |
| tristate "TI TPS65218 Power Management chips" |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the TPS65218 series of |
| Power Management chips. |
| These include voltage regulators, gpio and other features |
| that are often used in portable devices. Only regulator |
| component is currently supported. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps65218. |
| |
| config MFD_TPS6586X |
| bool "TI TPS6586x Power Management chips" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the TPS6586X series of |
| Power Management chips. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps6586x. |
| |
| config MFD_TPS65910 |
| bool "TI TPS65910 Power Management chip" |
| depends on I2C=y && GPIOLIB |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| select IRQ_DOMAIN |
| help |
| if you say yes here you get support for the TPS65910 series of |
| Power Management chips. |
| |
| config MFD_TPS65912 |
| bool "TI TPS65912 Power Management chip" |
| depends on GPIOLIB |
| select MFD_CORE |
| help |
| If you say yes here you get support for the TPS65912 series of |
| PM chips. |
| |
| config MFD_TPS65912_I2C |
| bool "TI TPS65912 Power Management chip with I2C" |
| select MFD_CORE |
| select MFD_TPS65912 |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the TPS65912 series of |
| PM chips with I2C interface. |
| |
| config MFD_TPS65912_SPI |
| bool "TI TPS65912 Power Management chip with SPI" |
| select MFD_CORE |
| select MFD_TPS65912 |
| depends on SPI_MASTER && GPIOLIB |
| help |
| If you say yes here you get support for the TPS65912 series of |
| PM chips with SPI interface. |
| |
| config MFD_TPS80031 |
| bool "TI TPS80031/TPS80032 Power Management chips" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the Texas Instruments |
| TPS80031/ TPS80032 Fully Integrated Power Management with Power |
| Path and Battery Charger. The device provides five configurable |
| step-down converters, 11 general purpose LDOs, USB OTG Module, |
| ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with |
| Power Path from USB, 32K clock generator. |
| |
| config TWL4030_CORE |
| bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support" |
| depends on I2C=y |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| help |
| Say yes here if you have TWL4030 / TWL6030 family chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| These multi-function chips are found on many OMAP2 and OMAP3 |
| boards, providing power management, RTC, GPIO, keypad, a |
| high speed USB OTG transceiver, an audio codec (on most |
| versions) and many other features. |
| |
| config TWL4030_POWER |
| bool "TI TWL4030 power resources" |
| depends on TWL4030_CORE && ARM |
| help |
| Say yes here if you want to use the power resources on the |
| TWL4030 family chips. Most of these resources are regulators, |
| which have a separate driver; some are control signals, such |
| as clock request handshaking. |
| |
| This driver uses board-specific data to initialize the resources |
| and load scripts controlling which resources are switched off/on |
| or reset when a sleep, wakeup or warm reset event occurs. |
| |
| config MFD_TWL4030_AUDIO |
| bool "TI TWL4030 Audio" |
| depends on TWL4030_CORE |
| select MFD_CORE |
| default n |
| |
| config TWL6040_CORE |
| bool "TI TWL6040 audio codec" |
| depends on I2C=y |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| default n |
| help |
| Say yes here if you want support for Texas Instruments TWL6040 audio |
| codec. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device (audio, vibra). |
| |
| config MENELAUS |
| bool "TI TWL92330/Menelaus PM chip" |
| depends on I2C=y && ARCH_OMAP2 |
| help |
| If you say yes here you get support for the Texas Instruments |
| TWL92330/Menelaus Power Management chip. This include voltage |
| regulators, Dual slot memory card transceivers, real-time clock |
| and other features that are often used in portable devices like |
| cell phones and PDAs. |
| |
| config MFD_WL1273_CORE |
| tristate "TI WL1273 FM radio" |
| depends on I2C |
| select MFD_CORE |
| default n |
| help |
| This is the core driver for the TI WL1273 FM radio. This MFD |
| driver connects the radio-wl1273 V4L2 module and the wl1273 |
| audio codec. |
| |
| config MFD_LM3533 |
| tristate "TI/National Semiconductor LM3533 Lighting Power chip" |
| depends on I2C |
| select MFD_CORE |
| select REGMAP_I2C |
| help |
| Say yes here to enable support for National Semiconductor / TI |
| LM3533 Lighting Power chips. |
| |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the LED, |
| backlight or ambient-light-sensor functionality of the device. |
| |
| config MFD_TIMBERDALE |
| tristate "Timberdale FPGA" |
| select MFD_CORE |
| depends on PCI && GPIOLIB && (X86_32 || COMPILE_TEST) |
| ---help--- |
| This is the core driver for the timberdale FPGA. This device is a |
| multifunction device which exposes numerous platform devices. |
| |
| The timberdale FPGA can be found on the Intel Atom development board |
| for in-vehicle infontainment, called Russellville. |
| |
| config MFD_TC3589X |
| bool "Toshiba TC35892 and variants" |
| depends on I2C=y |
| select MFD_CORE |
| help |
| Support for the Toshiba TC35892 and variants I/O Expander. |
| |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_TMIO |
| bool |
| default n |
| |
| config MFD_T7L66XB |
| bool "Toshiba T7L66XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller T7L66XB |
| |
| config MFD_TC6387XB |
| bool "Toshiba TC6387XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6387XB |
| |
| config MFD_TC6393XB |
| bool "Toshiba TC6393XB" |
| depends on ARM && HAVE_CLK |
| select GPIOLIB |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6393XB |
| |
| config MFD_VX855 |
| tristate "VIA VX855/VX875 integrated south bridge" |
| depends on PCI |
| select MFD_CORE |
| help |
| Say yes here to enable support for various functions of the |
| VIA VX855/VX875 south bridge. You will need to enable the vx855_spi |
| and/or vx855_gpio drivers for this to do anything useful. |
| |
| config MFD_ARIZONA |
| select REGMAP |
| select REGMAP_IRQ |
| select MFD_CORE |
| bool |
| |
| config MFD_ARIZONA_I2C |
| tristate "Wolfson Microelectronics Arizona platform with I2C" |
| select MFD_ARIZONA |
| select MFD_CORE |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Support for the Wolfson Microelectronics Arizona platform audio SoC |
| core functionality controlled via I2C. |
| |
| config MFD_ARIZONA_SPI |
| tristate "Wolfson Microelectronics Arizona platform with SPI" |
| select MFD_ARIZONA |
| select MFD_CORE |
| select REGMAP_SPI |
| depends on SPI_MASTER |
| help |
| Support for the Wolfson Microelectronics Arizona platform audio SoC |
| core functionality controlled via I2C. |
| |
| config MFD_WM5102 |
| bool "Wolfson Microelectronics WM5102" |
| depends on MFD_ARIZONA |
| help |
| Support for Wolfson Microelectronics WM5102 low power audio SoC |
| |
| config MFD_WM5110 |
| bool "Wolfson Microelectronics WM5110" |
| depends on MFD_ARIZONA |
| help |
| Support for Wolfson Microelectronics WM5110 low power audio SoC |
| |
| config MFD_WM8997 |
| bool "Wolfson Microelectronics WM8997" |
| depends on MFD_ARIZONA |
| help |
| Support for Wolfson Microelectronics WM8997 low power audio SoC |
| |
| config MFD_WM8400 |
| bool "Wolfson Microelectronics WM8400" |
| select MFD_CORE |
| depends on I2C=y |
| select REGMAP_I2C |
| help |
| Support for the Wolfson Microelecronics WM8400 PMIC and audio |
| CODEC. This driver provides common support for accessing |
| the device, additional drivers must be enabled in order to use |
| the functionality of the device. |
| |
| config MFD_WM831X |
| bool |
| |
| config MFD_WM831X_I2C |
| bool "Wolfson Microelectronics WM831x/2x PMICs with I2C" |
| select MFD_CORE |
| select MFD_WM831X |
| select REGMAP_I2C |
| select IRQ_DOMAIN |
| depends on I2C=y |
| help |
| Support for the Wolfson Microelecronics WM831x and WM832x PMICs |
| when controlled using I2C. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_WM831X_SPI |
| bool "Wolfson Microelectronics WM831x/2x PMICs with SPI" |
| select MFD_CORE |
| select MFD_WM831X |
| select REGMAP_SPI |
| select IRQ_DOMAIN |
| depends on SPI_MASTER |
| help |
| Support for the Wolfson Microelecronics WM831x and WM832x PMICs |
| when controlled using SPI. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_WM8350 |
| bool |
| |
| config MFD_WM8350_I2C |
| bool "Wolfson Microelectronics WM8350 with I2C" |
| select MFD_WM8350 |
| depends on I2C=y |
| help |
| The WM8350 is an integrated audio and power management |
| subsystem with watchdog and RTC functionality for embedded |
| systems. This option enables core support for the WM8350 with |
| I2C as the control interface. Additional options must be |
| selected to enable support for the functionality of the chip. |
| |
| config MFD_WM8994 |
| tristate "Wolfson Microelectronics WM8994" |
| select MFD_CORE |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| depends on I2C |
| help |
| The WM8994 is a highly integrated hi-fi CODEC designed for |
| smartphone applicatiosn. As well as audio functionality it |
| has on board GPIO and regulator functionality which is |
| supported via the relevant subsystems. This driver provides |
| core support for the WM8994, in order to use the actual |
| functionaltiy of the device other drivers must be enabled. |
| |
| config MFD_STW481X |
| tristate "Support for ST Microelectronics STw481x" |
| depends on I2C && ARCH_NOMADIK |
| select REGMAP_I2C |
| select MFD_CORE |
| help |
| Select this option to enable the STw481x chip driver used |
| in various ST Microelectronics and ST-Ericsson embedded |
| Nomadik series. |
| |
| menu "Multimedia Capabilities Port drivers" |
| depends on ARCH_SA1100 |
| |
| config MCP |
| tristate |
| |
| # Interface drivers |
| config MCP_SA11X0 |
| tristate "Support SA11x0 MCP interface" |
| depends on ARCH_SA1100 |
| select MCP |
| |
| # Chip drivers |
| config MCP_UCB1200 |
| tristate "Support for UCB1200 / UCB1300" |
| depends on MCP_SA11X0 |
| select MCP |
| |
| config MCP_UCB1200_TS |
| tristate "Touchscreen interface support" |
| depends on MCP_UCB1200 && INPUT |
| |
| endmenu |
| |
| config MFD_VEXPRESS_SYSREG |
| bool "Versatile Express System Registers" |
| depends on VEXPRESS_CONFIG && GPIOLIB |
| default y |
| select CLKSRC_MMIO |
| select GPIO_GENERIC_PLATFORM |
| select MFD_CORE |
| select MFD_SYSCON |
| help |
| System Registers are the platform configuration block |
| on the ARM Ltd. Versatile Express board. |
| |
| endmenu |
| endif |