diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index b53b937..c8954a6 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -51,6 +51,8 @@
 
 #include <asm/arch/gpio.h>
 #include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/at91sam9261_matrix.h>
 
 #include "at91_udc.h"
 
@@ -909,11 +911,37 @@
 	if (is_on) {
 		clk_on(udc);
 		at91_udp_write(udc, AT91_UDP_TXVC, 0);
-		at91_set_gpio_value(udc->board.pullup_pin, 1);
+		if (cpu_is_at91rm9200())
+			at91_set_gpio_value(udc->board.pullup_pin, 1);
+		else if (cpu_is_at91sam9260()) {
+			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
+
+			txvc |= AT91_UDP_TXVC_PUON;
+			at91_udp_write(udc, AT91_UDP_TXVC, txvc);
+		} else if (cpu_is_at91sam9261()) {
+			u32	usbpucr;
+
+			usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+			usbpucr |= AT91_MATRIX_USBPUCR_PUON;
+			at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+		}
 	} else {
 		stop_activity(udc);
 		at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
-		at91_set_gpio_value(udc->board.pullup_pin, 0);
+		if (cpu_is_at91rm9200())
+			at91_set_gpio_value(udc->board.pullup_pin, 0);
+		else if (cpu_is_at91sam9260()) {
+			u32	txvc = at91_udp_read(udc, AT91_UDP_TXVC);
+
+			txvc &= ~AT91_UDP_TXVC_PUON;
+			at91_udp_write(udc, AT91_UDP_TXVC, txvc);
+		} else if (cpu_is_at91sam9261()) {
+			u32	usbpucr;
+
+			usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+			usbpucr &= ~AT91_MATRIX_USBPUCR_PUON;
+			at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+		}
 		clk_off(udc);
 	}
 }
@@ -1668,7 +1696,8 @@
 	udc->fclk = clk_get(dev, "udpck");
 	if (IS_ERR(udc->iclk) || IS_ERR(udc->fclk)) {
 		DBG("clocks missing\n");
-		return -ENODEV;
+		retval = -ENODEV;
+		goto fail0;
 	}
 
 	retval = device_register(&udc->gadget.dev);
@@ -1679,6 +1708,8 @@
 	clk_enable(udc->iclk);
 	at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
 	at91_udp_write(udc, AT91_UDP_IDR, 0xffffffff);
+	/* Clear all pending interrupts - UDP may be used by bootloader. */
+	at91_udp_write(udc, AT91_UDP_ICR, 0xffffffff);
 	clk_disable(udc->iclk);
 
 	/* request UDC and maybe VBUS irqs */
@@ -1690,6 +1721,11 @@
 		goto fail1;
 	}
 	if (udc->board.vbus_pin > 0) {
+		/*
+		 * Get the initial state of VBUS - we cannot expect
+		 * a pending interrupt.
+		 */
+		udc->vbus = at91_get_gpio_value(udc->board.vbus_pin);
 		if (request_irq(udc->board.vbus_pin, at91_vbus_irq,
 				IRQF_DISABLED, driver_name, udc)) {
 			DBG("request vbus irq %d failed\n",
diff --git a/drivers/usb/gadget/at91_udc.h b/drivers/usb/gadget/at91_udc.h
index a35f3b6..677089b 100644
--- a/drivers/usb/gadget/at91_udc.h
+++ b/drivers/usb/gadget/at91_udc.h
@@ -51,10 +51,10 @@
 #define     AT91_UDP_EP(n)	(1 << (n))	/* Endpoint Interrupt Status */
 #define     AT91_UDP_RXSUSP	(1 <<  8) 	/* USB Suspend Interrupt Status */
 #define     AT91_UDP_RXRSM	(1 <<  9)	/* USB Resume Interrupt Status */
-#define     AT91_UDP_EXTRSM	(1 << 10)	/* External Resume Interrupt Status */
+#define     AT91_UDP_EXTRSM	(1 << 10)	/* External Resume Interrupt Status [AT91RM9200 only] */
 #define     AT91_UDP_SOFINT	(1 << 11)	/* Start of Frame Interrupt Status */
 #define     AT91_UDP_ENDBUSRES	(1 << 12)	/* End of Bus Reset Interrpt Status */
-#define     AT91_UDP_WAKEUP	(1 << 13)	/* USB Wakeup Interrupt Status */
+#define     AT91_UDP_WAKEUP	(1 << 13)	/* USB Wakeup Interrupt Status [AT91RM9200 only] */
 
 #define AT91_UDP_ICR		0x20		/* Interrupt Clear Register */
 #define AT91_UDP_RST_EP		0x28		/* Reset Endpoint Register */
@@ -84,7 +84,7 @@
 
 #define AT91_UDP_TXVC		0x74		/* Transceiver Control Register */
 #define     AT91_UDP_TXVC_TXVDIS (1 << 8)	/* Transceiver Disable */
-
+#define     AT91_UDP_TXVC_PUON   (1 << 9)	/* PullUp On [AT91SAM9260 only] */
 
 /*-------------------------------------------------------------------------*/