m68k/atari - atari_scsi: change abort/reset return codes
[Resend of earlier patch - added equivalent changes to sun3 NCR5380 code]
The abort/reset lowlevel return codes had changed with the new
error SCSI handling - update Atari and Sun3 NCR5380 drivers to reflect this.
Change reset handling for Atari to clear queues only, do not attempt
to call done() on each command aborted by the reset. The EH code
should do that for us. Queues _must_ be cleared, otherwise
atari_scsi_bus_reset will not release the ST-DMA lock, deadlocking
further error recovery.
Update the Sun3 NCR5380 driver as well - the Sun3 driver was
derived from the Atari one. Kudos to Finn Thain for the Sun3 part
and cleaning up the header files. After the header cleanup, the
initio.h include (!) can be dropped from sun3_scsi.h now.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Sam Creasey <sammy@sammy.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
diff --git a/drivers/scsi/atari_NCR5380.c b/drivers/scsi/atari_NCR5380.c
index 0f3cdbc..e4aaf9a 100644
--- a/drivers/scsi/atari_NCR5380.c
+++ b/drivers/scsi/atari_NCR5380.c
@@ -2683,11 +2683,11 @@
local_irq_restore(flags);
cmd->scsi_done(cmd);
falcon_release_lock_if_possible(hostdata);
- return SCSI_ABORT_SUCCESS;
+ return SUCCESS;
} else {
/* local_irq_restore(flags); */
printk("scsi%d: abort of connected command failed!\n", HOSTNO);
- return SCSI_ABORT_ERROR;
+ return FAILED;
}
}
#endif
@@ -2711,7 +2711,7 @@
* yet... */
tmp->scsi_done(tmp);
falcon_release_lock_if_possible(hostdata);
- return SCSI_ABORT_SUCCESS;
+ return SUCCESS;
}
}
@@ -2729,7 +2729,7 @@
if (hostdata->connected) {
local_irq_restore(flags);
ABRT_PRINTK("scsi%d: abort failed, command connected.\n", HOSTNO);
- return SCSI_ABORT_SNOOZE;
+ return FAILED;
}
/*
@@ -2764,7 +2764,7 @@
ABRT_PRINTK("scsi%d: aborting disconnected command.\n", HOSTNO);
if (NCR5380_select(instance, cmd, (int)cmd->tag))
- return SCSI_ABORT_BUSY;
+ return FAILED;
ABRT_PRINTK("scsi%d: nexus reestablished.\n", HOSTNO);
@@ -2791,7 +2791,7 @@
local_irq_restore(flags);
tmp->scsi_done(tmp);
falcon_release_lock_if_possible(hostdata);
- return SCSI_ABORT_SUCCESS;
+ return SUCCESS;
}
}
}
@@ -2816,7 +2816,7 @@
*/
falcon_release_lock_if_possible(hostdata);
- return SCSI_ABORT_NOT_RUNNING;
+ return FAILED;
}
@@ -2825,7 +2825,7 @@
*
* Purpose : reset the SCSI bus.
*
- * Returns : SCSI_RESET_WAKEUP
+ * Returns : SUCCESS or FAILURE
*
*/
@@ -2834,7 +2834,7 @@
SETUP_HOSTDATA(cmd->device->host);
int i;
unsigned long flags;
-#if 1
+#if defined(RESET_RUN_DONE)
Scsi_Cmnd *connected, *disconnected_queue;
#endif
@@ -2859,7 +2859,14 @@
* through anymore ... */
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-#if 1 /* XXX Should now be done by midlevel code, but it's broken XXX */
+ /* MSch 20140115 - looking at the generic NCR5380 driver, all of this
+ * should go.
+ * Catch-22: if we don't clear all queues, the SCSI driver lock will
+ * not be reset by atari_scsi_reset()!
+ */
+
+#if defined(RESET_RUN_DONE)
+ /* XXX Should now be done by midlevel code, but it's broken XXX */
/* XXX see below XXX */
/* MSch: old-style reset: actually abort all command processing here */
@@ -2915,7 +2922,7 @@
* the midlevel code that the reset was SUCCESSFUL, and there is no
* need to 'wake up' the commands by a request_sense
*/
- return SCSI_RESET_SUCCESS | SCSI_RESET_BUS_RESET;
+ return SUCCESS;
#else /* 1 */
/* MSch: new-style reset handling: let the mid-level do what it can */
@@ -2963,6 +2970,6 @@
local_irq_restore(flags);
/* we did no complete reset of all commands, so a wakeup is required */
- return SCSI_RESET_WAKEUP | SCSI_RESET_BUS_RESET;
+ return SUCCESS;
#endif /* 1 */
}