xhci: USB 3.0 BW checking.
The Intel Panther Point xHCI host tracks SuperSpeed endpoints in a
different way than USB 2.0/1.1 endpoints. The bandwidth interval tables
are not used, and instead the bandwidth is calculated in a very simple
way. Bandwidth for SuperSpeed endpoints is tracked individually in each
direction, since each direction has the full USB 3.0 bandwidth available.
10% of the bus bandwidth is reserved for non-periodic transfers.
This checking would be more complex if we had USB 3.0 LPM enabled, because
an additional latency for isochronous ping times need to be taken into
account. However, we don't have USB 3.0 LPM support in Linux yet.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 7583b24..54cb762 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -1810,6 +1810,22 @@
return 0;
}
+static int xhci_check_ss_bw(struct xhci_hcd *xhci,
+ struct xhci_virt_device *virt_dev)
+{
+ unsigned int bw_reserved;
+
+ bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_IN, 100);
+ if (virt_dev->bw_table->ss_bw_in > (SS_BW_LIMIT_IN - bw_reserved))
+ return -ENOMEM;
+
+ bw_reserved = DIV_ROUND_UP(SS_BW_RESERVED*SS_BW_LIMIT_OUT, 100);
+ if (virt_dev->bw_table->ss_bw_out > (SS_BW_LIMIT_OUT - bw_reserved))
+ return -ENOMEM;
+
+ return 0;
+}
+
/*
* This algorithm is a very conservative estimate of the worst-case scheduling
* scenario for any one interval. The hardware dynamically schedules the
@@ -1866,6 +1882,9 @@
unsigned int packets_remaining = 0;
unsigned int i;
+ if (virt_dev->udev->speed == USB_SPEED_SUPER)
+ return xhci_check_ss_bw(xhci, virt_dev);
+
if (virt_dev->udev->speed == USB_SPEED_HIGH) {
max_bandwidth = HS_BW_LIMIT;
/* Convert percent of bus BW reserved to blocks reserved */
@@ -2028,6 +2047,25 @@
ep_type != INT_IN_EP);
}
+static bool xhci_is_sync_in_ep(unsigned int ep_type)
+{
+ return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
+}
+
+static unsigned int xhci_get_ss_bw_consumed(struct xhci_bw_info *ep_bw)
+{
+ unsigned int mps = DIV_ROUND_UP(ep_bw->max_packet_size, SS_BLOCK);
+
+ if (ep_bw->ep_interval == 0)
+ return SS_OVERHEAD_BURST +
+ (ep_bw->mult * ep_bw->num_packets *
+ (SS_OVERHEAD + mps));
+ return DIV_ROUND_UP(ep_bw->mult * ep_bw->num_packets *
+ (SS_OVERHEAD + mps + SS_OVERHEAD_BURST),
+ 1 << ep_bw->ep_interval);
+
+}
+
void xhci_drop_ep_from_interval_table(struct xhci_hcd *xhci,
struct xhci_bw_info *ep_bw,
struct xhci_interval_bw_table *bw_table,
@@ -2038,10 +2076,24 @@
struct xhci_interval_bw *interval_bw;
int normalized_interval;
- if (xhci_is_async_ep(ep_bw->type) ||
- list_empty(&virt_ep->bw_endpoint_list))
+ if (xhci_is_async_ep(ep_bw->type))
return;
+ if (udev->speed == USB_SPEED_SUPER) {
+ if (xhci_is_sync_in_ep(ep_bw->type))
+ xhci->devs[udev->slot_id]->bw_table->ss_bw_in -=
+ xhci_get_ss_bw_consumed(ep_bw);
+ else
+ xhci->devs[udev->slot_id]->bw_table->ss_bw_out -=
+ xhci_get_ss_bw_consumed(ep_bw);
+ return;
+ }
+
+ /* SuperSpeed endpoints never get added to intervals in the table, so
+ * this check is only valid for HS/FS/LS devices.
+ */
+ if (list_empty(&virt_ep->bw_endpoint_list))
+ return;
/* For LS/FS devices, we need to translate the interval expressed in
* microframes to frames.
*/
@@ -2091,6 +2143,16 @@
if (xhci_is_async_ep(ep_bw->type))
return;
+ if (udev->speed == USB_SPEED_SUPER) {
+ if (xhci_is_sync_in_ep(ep_bw->type))
+ xhci->devs[udev->slot_id]->bw_table->ss_bw_in +=
+ xhci_get_ss_bw_consumed(ep_bw);
+ else
+ xhci->devs[udev->slot_id]->bw_table->ss_bw_out +=
+ xhci_get_ss_bw_consumed(ep_bw);
+ return;
+ }
+
/* For LS/FS devices, we need to translate the interval expressed in
* microframes to frames.
*/
@@ -2169,9 +2231,6 @@
struct xhci_input_control_ctx *ctrl_ctx;
int old_active_eps = 0;
- if (virt_dev->udev->speed == USB_SPEED_SUPER)
- return 0;
-
if (virt_dev->tt_info)
old_active_eps = virt_dev->tt_info->active_eps;