Add ipw2100 wireless driver.
diff --git a/Documentation/networking/README.ipw2100 b/Documentation/networking/README.ipw2100
new file mode 100644
index 0000000..2046948
--- /dev/null
+++ b/Documentation/networking/README.ipw2100
@@ -0,0 +1,246 @@
+
+===========================
+Intel(R) PRO/Wireless 2100 Network Connection Driver for Linux
+README.ipw2100
+
+March 14, 2005
+
+===========================
+Index
+---------------------------
+0. Introduction
+1. Release 1.1.0 Current Features
+2. Command Line Parameters
+3. Sysfs Helper Files
+4. Radio Kill Switch
+5. Dynamic Firmware
+6. Power Management
+7. Support
+8. License
+
+
+===========================
+0. Introduction
+------------ ----- ----- ---- --- -- -
+
+This document provides a brief overview of the features supported by the
+IPW2100 driver project. The main project website, where the latest
+development version of the driver can be found, is:
+
+ http://ipw2100.sourceforge.net
+
+There you can find the not only the latest releases, but also information about
+potential fixes and patches, as well as links to the development mailing list
+for the driver project.
+
+
+===========================
+1. Release 1.1.0 Current Supported Features
+---------------------------
+- Managed (BSS) and Ad-Hoc (IBSS)
+- WEP (shared key and open)
+- Wireless Tools support
+- 802.1x (tested with XSupplicant 1.0.1)
+
+Enabled (but not supported) features:
+- Monitor/RFMon mode
+- WPA/WPA2
+
+The distinction between officially supported and enabled is a reflection
+on the amount of validation and interoperability testing that has been
+performed on a given feature.
+
+
+===========================
+2. Command Line Parameters
+---------------------------
+
+If the driver is built as a module, the following optional parameters are used
+by entering them on the command line with the modprobe command using this
+syntax:
+
+ modprobe ipw2100 [<option>=<VAL1><,VAL2>...]
+
+For example, to disable the radio on driver loading, enter:
+
+ modprobe ipw2100 disable=1
+
+The ipw2100 driver supports the following module parameters:
+
+Name Value Example:
+debug 0x0-0xffffffff debug=1024
+mode 0,1,2 mode=1 /* AdHoc */
+channel int channel=3 /* Only valid in AdHoc or Monitor */
+associate boolean associate=0 /* Do NOT auto associate */
+disable boolean disable=1 /* Do not power the HW */
+
+
+===========================
+3. Sysfs Helper Files
+---------------------------
+
+There are several ways to control the behavior of the driver. Many of the
+general capabilities are exposed through the Wireless Tools (iwconfig). There
+are a few capabilities that are exposed through entries in the Linux Sysfs.
+
+
+----- Driver Level ------
+For the driver level files, look in /sys/bus/pci/drivers/ipw2100/
+
+ debug_level
+
+ This controls the same global as the 'debug' module parameter. For
+ information on the various debugging levels available, run the 'dvals'
+ script found in the driver source directory.
+
+ NOTE: 'debug_level' is only enabled if CONFIG_IPW2100_DEBUG is turn
+ on.
+
+----- Device Level ------
+For the device level files look in
+
+ /sys/bus/pci/drivers/ipw2100/{PCI-ID}/
+
+For example:
+ /sys/bus/pci/drivers/ipw2100/0000:02:01.0
+
+For the device level files, see /sys/bus/pci/drivers/ipw2100:
+
+ rf_kill
+ read -
+ 0 = RF kill not enabled (radio on)
+ 1 = SW based RF kill active (radio off)
+ 2 = HW based RF kill active (radio off)
+ 3 = Both HW and SW RF kill active (radio off)
+ write -
+ 0 = If SW based RF kill active, turn the radio back on
+ 1 = If radio is on, activate SW based RF kill
+
+ NOTE: If you enable the SW based RF kill and then toggle the HW
+ based RF kill from ON -> OFF -> ON, the radio will NOT come back on
+
+
+===========================
+4. Radio Kill Switch
+---------------------------
+Most laptops provide the ability for the user to physically disable the radio.
+Some vendors have implemented this as a physical switch that requires no
+software to turn the radio off and on. On other laptops, however, the switch
+is controlled through a button being pressed and a software driver then making
+calls to turn the radio off and on. This is referred to as a "software based
+RF kill switch"
+
+See the Sysfs helper file 'rf_kill' for determining the state of the RF switch
+on your system.
+
+
+===========================
+5. Dynamic Firmware
+---------------------------
+As the firmware is licensed under a restricted use license, it can not be
+included within the kernel sources. To enable the IPW2100 you will need a
+firmware image to load into the wireless NIC's processors.
+
+You can obtain these images from <http://ipw2100.sf.net/firmware.php>.
+
+See INSTALL for instructions on installing the firmware.
+
+
+===========================
+6. Power Management
+---------------------------
+The IPW2100 supports the configuration of the Power Save Protocol
+through a private wireless extension interface. The IPW2100 supports
+the following different modes:
+
+ off No power management. Radio is always on.
+ on Automatic power management
+ 1-5 Different levels of power management. The higher the
+ number the greater the power savings, but with an impact to
+ packet latencies.
+
+Power management works by powering down the radio after a certain
+interval of time has passed where no packets are passed through the
+radio. Once powered down, the radio remains in that state for a given
+period of time. For higher power savings, the interval between last
+packet processed to sleep is shorter and the sleep period is longer.
+
+When the radio is asleep, the access point sending data to the station
+must buffer packets at the AP until the station wakes up and requests
+any buffered packets. If you have an AP that does not correctly support
+the PSP protocol you may experience packet loss or very poor performance
+while power management is enabled. If this is the case, you will need
+to try and find a firmware update for your AP, or disable power
+management (via `iwconfig eth1 power off`)
+
+To configure the power level on the IPW2100 you use a combination of
+iwconfig and iwpriv. iwconfig is used to turn power management on, off,
+and set it to auto.
+
+ iwconfig eth1 power off Disables radio power down
+ iwconfig eth1 power on Enables radio power management to
+ last set level (defaults to AUTO)
+ iwpriv eth1 set_power 0 Sets power level to AUTO and enables
+ power management if not previously
+ enabled.
+ iwpriv eth1 set_power 1-5 Set the power level as specified,
+ enabling power management if not
+ previously enabled.
+
+You can view the current power level setting via:
+
+ iwpriv eth1 get_power
+
+It will return the current period or timeout that is configured as a string
+in the form of xxxx/yyyy (z) where xxxx is the timeout interval (amount of
+time after packet processing), yyyy is the period to sleep (amount of time to
+wait before powering the radio and querying the access point for buffered
+packets), and z is the 'power level'. If power management is turned off the
+xxxx/yyyy will be replaced with 'off' -- the level reported will be the active
+level if `iwconfig eth1 power on` is invoked.
+
+
+===========================
+7. Support
+---------------------------
+
+For general development information and support,
+go to:
+
+ http://ipw2100.sf.net/
+
+The ipw2100 1.1.0 driver and firmware can be downloaded from:
+
+ http://support.intel.com
+
+For installation support on the ipw2100 1.1.0 driver on Linux kernels
+2.6.8 or greater, email support is available from:
+
+ http://supportmail.intel.com
+
+===========================
+8. License
+---------------------------
+
+ Copyright(c) 2003 - 2005 Intel Corporation. All rights reserved.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms of the GNU General Public License (version 2) as
+ published by the Free Software Foundation.
+
+ This program is distributed in the hope that it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc., 59
+ Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+
+ The full GNU General Public License is included in this distribution in the
+ file called LICENSE.
+
+ License Contact Information:
+ James P. Ketrenos <ipw2100-admin@linux.intel.com>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+