usb: dwc3: Use the correct speed macros for DSTS/DCFG
Correct the use of the DWC3_DSTS_XXX_SPEED and DWC3_DCFG_XXX_SPEED
macros. The wrong set of macros were being used in a few places.
This is only a cosmetic change as the values for both sets are
identical.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index d0f7458..0c11fd6 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -1672,16 +1672,16 @@
} else {
switch (dwc->maximum_speed) {
case USB_SPEED_LOW:
- reg |= DWC3_DSTS_LOWSPEED;
+ reg |= DWC3_DCFG_LOWSPEED;
break;
case USB_SPEED_FULL:
- reg |= DWC3_DSTS_FULLSPEED1;
+ reg |= DWC3_DCFG_FULLSPEED1;
break;
case USB_SPEED_HIGH:
- reg |= DWC3_DSTS_HIGHSPEED;
+ reg |= DWC3_DCFG_HIGHSPEED;
break;
case USB_SPEED_SUPER_PLUS:
- reg |= DWC3_DSTS_SUPERSPEED_PLUS;
+ reg |= DWC3_DCFG_SUPERSPEED_PLUS;
break;
default:
dev_err(dwc->dev, "invalid dwc->maximum_speed (%d)\n",
@@ -2459,12 +2459,12 @@
dwc3_update_ram_clk_sel(dwc, speed);
switch (speed) {
- case DWC3_DCFG_SUPERSPEED_PLUS:
+ case DWC3_DSTS_SUPERSPEED_PLUS:
dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
dwc->gadget.ep0->maxpacket = 512;
dwc->gadget.speed = USB_SPEED_SUPER_PLUS;
break;
- case DWC3_DCFG_SUPERSPEED:
+ case DWC3_DSTS_SUPERSPEED:
/*
* WORKAROUND: DWC3 revisions <1.90a have an issue which
* would cause a missing USB3 Reset event.
@@ -2485,18 +2485,18 @@
dwc->gadget.ep0->maxpacket = 512;
dwc->gadget.speed = USB_SPEED_SUPER;
break;
- case DWC3_DCFG_HIGHSPEED:
+ case DWC3_DSTS_HIGHSPEED:
dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64);
dwc->gadget.ep0->maxpacket = 64;
dwc->gadget.speed = USB_SPEED_HIGH;
break;
- case DWC3_DCFG_FULLSPEED2:
- case DWC3_DCFG_FULLSPEED1:
+ case DWC3_DSTS_FULLSPEED2:
+ case DWC3_DSTS_FULLSPEED1:
dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64);
dwc->gadget.ep0->maxpacket = 64;
dwc->gadget.speed = USB_SPEED_FULL;
break;
- case DWC3_DCFG_LOWSPEED:
+ case DWC3_DSTS_LOWSPEED:
dwc3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(8);
dwc->gadget.ep0->maxpacket = 8;
dwc->gadget.speed = USB_SPEED_LOW;
@@ -2506,8 +2506,8 @@
/* Enable USB2 LPM Capability */
if ((dwc->revision > DWC3_REVISION_194A) &&
- (speed != DWC3_DCFG_SUPERSPEED) &&
- (speed != DWC3_DCFG_SUPERSPEED_PLUS)) {
+ (speed != DWC3_DSTS_SUPERSPEED) &&
+ (speed != DWC3_DSTS_SUPERSPEED_PLUS)) {
reg = dwc3_readl(dwc->regs, DWC3_DCFG);
reg |= DWC3_DCFG_LPM_CAP;
dwc3_writel(dwc->regs, DWC3_DCFG, reg);