[netdrvr] Use dev_printk() when ethernet interface isn't available
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/epic100.c b/drivers/net/epic100.c
index 05c9a26..6dd0e9d 100644
--- a/drivers/net/epic100.c
+++ b/drivers/net/epic100.c
@@ -422,8 +422,7 @@
((u16 *)dev->dev_addr)[i] = le16_to_cpu(inw(ioaddr + LAN0 + i*4));
if (debug > 2) {
- printk(KERN_DEBUG DRV_NAME "(%s): EEPROM contents\n",
- pci_name(pdev));
+ dev_printk(KERN_DEBUG, &pdev->dev, "EEPROM contents:\n");
for (i = 0; i < 64; i++)
printk(" %4.4x%s", read_eeprom(ioaddr, i),
i % 16 == 15 ? "\n" : "");
@@ -445,21 +444,23 @@
int mii_status = mdio_read(dev, phy, MII_BMSR);
if (mii_status != 0xffff && mii_status != 0x0000) {
ep->phys[phy_idx++] = phy;
- printk(KERN_INFO DRV_NAME "(%s): MII transceiver #%d control "
- "%4.4x status %4.4x.\n",
- pci_name(pdev), phy, mdio_read(dev, phy, 0), mii_status);
+ dev_printk(KERN_INFO, &pdev->dev,
+ "MII transceiver #%d control "
+ "%4.4x status %4.4x.\n",
+ phy, mdio_read(dev, phy, 0), mii_status);
}
}
ep->mii_phy_cnt = phy_idx;
if (phy_idx != 0) {
phy = ep->phys[0];
ep->mii.advertising = mdio_read(dev, phy, MII_ADVERTISE);
- printk(KERN_INFO DRV_NAME "(%s): Autonegotiation advertising %4.4x link "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Autonegotiation advertising %4.4x link "
"partner %4.4x.\n",
- pci_name(pdev), ep->mii.advertising, mdio_read(dev, phy, 5));
+ ep->mii.advertising, mdio_read(dev, phy, 5));
} else if ( ! (ep->chip_flags & NO_MII)) {
- printk(KERN_WARNING DRV_NAME "(%s): ***WARNING***: No MII transceiver found!\n",
- pci_name(pdev));
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "***WARNING***: No MII transceiver found!\n");
/* Use the known PHY address of the EPII. */
ep->phys[0] = 3;
}
@@ -474,8 +475,8 @@
/* The lower four bits are the media type. */
if (duplex) {
ep->mii.force_media = ep->mii.full_duplex = 1;
- printk(KERN_INFO DRV_NAME "(%s): Forced full duplex operation requested.\n",
- pci_name(pdev));
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Forced full duplex operation requested.\n");
}
dev->if_port = ep->default_port = option;