| /* |
| * Copyright 2012 Freescale Semiconductor, Inc. |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include "skeleton.dtsi" |
| #include "imx28-pinfunc.h" |
| |
| / { |
| interrupt-parent = <&icoll>; |
| |
| aliases { |
| ethernet0 = &mac0; |
| ethernet1 = &mac1; |
| gpio0 = &gpio0; |
| gpio1 = &gpio1; |
| gpio2 = &gpio2; |
| gpio3 = &gpio3; |
| gpio4 = &gpio4; |
| saif0 = &saif0; |
| saif1 = &saif1; |
| serial0 = &auart0; |
| serial1 = &auart1; |
| serial2 = &auart2; |
| serial3 = &auart3; |
| serial4 = &auart4; |
| spi0 = &ssp1; |
| spi1 = &ssp2; |
| usbphy0 = &usbphy0; |
| usbphy1 = &usbphy1; |
| }; |
| |
| cpus { |
| #address-cells = <0>; |
| #size-cells = <0>; |
| |
| cpu { |
| compatible = "arm,arm926ej-s"; |
| device_type = "cpu"; |
| }; |
| }; |
| |
| apb@80000000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x80000000 0x80000>; |
| ranges; |
| |
| apbh@80000000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x80000000 0x3c900>; |
| ranges; |
| |
| icoll: interrupt-controller@80000000 { |
| compatible = "fsl,imx28-icoll", "fsl,icoll"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x80000000 0x2000>; |
| }; |
| |
| hsadc: hsadc@80002000 { |
| reg = <0x80002000 0x2000>; |
| interrupts = <13>; |
| dmas = <&dma_apbh 12>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| dma_apbh: dma-apbh@80004000 { |
| compatible = "fsl,imx28-dma-apbh"; |
| reg = <0x80004000 0x2000>; |
| interrupts = <82 83 84 85 |
| 88 88 88 88 |
| 88 88 88 88 |
| 87 86 0 0>; |
| interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3", |
| "gpmi0", "gmpi1", "gpmi2", "gmpi3", |
| "gpmi4", "gmpi5", "gpmi6", "gmpi7", |
| "hsadc", "lcdif", "empty", "empty"; |
| #dma-cells = <1>; |
| dma-channels = <16>; |
| clocks = <&clks 25>; |
| }; |
| |
| perfmon: perfmon@80006000 { |
| reg = <0x80006000 0x800>; |
| interrupts = <27>; |
| status = "disabled"; |
| }; |
| |
| gpmi: gpmi-nand@8000c000 { |
| compatible = "fsl,imx28-gpmi-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>; |
| reg-names = "gpmi-nand", "bch"; |
| interrupts = <41>; |
| interrupt-names = "bch"; |
| clocks = <&clks 50>; |
| clock-names = "gpmi_io"; |
| dmas = <&dma_apbh 4>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| ssp0: ssp@80010000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x80010000 0x2000>; |
| interrupts = <96>; |
| clocks = <&clks 46>; |
| dmas = <&dma_apbh 0>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| ssp1: ssp@80012000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x80012000 0x2000>; |
| interrupts = <97>; |
| clocks = <&clks 47>; |
| dmas = <&dma_apbh 1>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| ssp2: ssp@80014000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x80014000 0x2000>; |
| interrupts = <98>; |
| clocks = <&clks 48>; |
| dmas = <&dma_apbh 2>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| ssp3: ssp@80016000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x80016000 0x2000>; |
| interrupts = <99>; |
| clocks = <&clks 49>; |
| dmas = <&dma_apbh 3>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| pinctrl: pinctrl@80018000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx28-pinctrl", "simple-bus"; |
| reg = <0x80018000 0x2000>; |
| |
| gpio0: gpio@0 { |
| compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; |
| interrupts = <127>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio@1 { |
| compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; |
| interrupts = <126>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@2 { |
| compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; |
| interrupts = <125>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@3 { |
| compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; |
| interrupts = <124>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@4 { |
| compatible = "fsl,imx28-gpio", "fsl,mxs-gpio"; |
| interrupts = <123>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| duart_pins_a: duart@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM0__DUART_RX |
| MX28_PAD_PWM1__DUART_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| duart_pins_b: duart@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART0_CTS__DUART_RX |
| MX28_PAD_AUART0_RTS__DUART_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| duart_4pins_a: duart-4pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART0_CTS__DUART_RX |
| MX28_PAD_AUART0_RTS__DUART_TX |
| MX28_PAD_AUART0_RX__DUART_CTS |
| MX28_PAD_AUART0_TX__DUART_RTS |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| gpmi_pins_a: gpmi-nand@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_D00__GPMI_D0 |
| MX28_PAD_GPMI_D01__GPMI_D1 |
| MX28_PAD_GPMI_D02__GPMI_D2 |
| MX28_PAD_GPMI_D03__GPMI_D3 |
| MX28_PAD_GPMI_D04__GPMI_D4 |
| MX28_PAD_GPMI_D05__GPMI_D5 |
| MX28_PAD_GPMI_D06__GPMI_D6 |
| MX28_PAD_GPMI_D07__GPMI_D7 |
| MX28_PAD_GPMI_CE0N__GPMI_CE0N |
| MX28_PAD_GPMI_RDY0__GPMI_READY0 |
| MX28_PAD_GPMI_RDN__GPMI_RDN |
| MX28_PAD_GPMI_WRN__GPMI_WRN |
| MX28_PAD_GPMI_ALE__GPMI_ALE |
| MX28_PAD_GPMI_CLE__GPMI_CLE |
| MX28_PAD_GPMI_RESETN__GPMI_RESETN |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| gpmi_status_cfg: gpmi-status-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_RDN__GPMI_RDN |
| MX28_PAD_GPMI_WRN__GPMI_WRN |
| MX28_PAD_GPMI_RESETN__GPMI_RESETN |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| }; |
| |
| auart0_pins_a: auart0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART0_RX__AUART0_RX |
| MX28_PAD_AUART0_TX__AUART0_TX |
| MX28_PAD_AUART0_CTS__AUART0_CTS |
| MX28_PAD_AUART0_RTS__AUART0_RTS |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart0_2pins_a: auart0-2pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART0_RX__AUART0_RX |
| MX28_PAD_AUART0_TX__AUART0_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart1_pins_a: auart1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART1_RX__AUART1_RX |
| MX28_PAD_AUART1_TX__AUART1_TX |
| MX28_PAD_AUART1_CTS__AUART1_CTS |
| MX28_PAD_AUART1_RTS__AUART1_RTS |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart1_2pins_a: auart1-2pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART1_RX__AUART1_RX |
| MX28_PAD_AUART1_TX__AUART1_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart2_2pins_a: auart2-2pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP2_SCK__AUART2_RX |
| MX28_PAD_SSP2_MOSI__AUART2_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart2_2pins_b: auart2-2pins@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART2_RX__AUART2_RX |
| MX28_PAD_AUART2_TX__AUART2_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart2_pins_a: auart2-pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART2_RX__AUART2_RX |
| MX28_PAD_AUART2_TX__AUART2_TX |
| MX28_PAD_AUART2_CTS__AUART2_CTS |
| MX28_PAD_AUART2_RTS__AUART2_RTS |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart3_pins_a: auart3@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART3_RX__AUART3_RX |
| MX28_PAD_AUART3_TX__AUART3_TX |
| MX28_PAD_AUART3_CTS__AUART3_CTS |
| MX28_PAD_AUART3_RTS__AUART3_RTS |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart3_2pins_a: auart3-2pins@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP2_MISO__AUART3_RX |
| MX28_PAD_SSP2_SS0__AUART3_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart3_2pins_b: auart3-2pins@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART3_RX__AUART3_RX |
| MX28_PAD_AUART3_TX__AUART3_TX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| auart4_2pins_a: auart4@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP3_SCK__AUART4_TX |
| MX28_PAD_SSP3_MOSI__AUART4_RX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| mac0_pins_a: mac0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_ENET0_MDC__ENET0_MDC |
| MX28_PAD_ENET0_MDIO__ENET0_MDIO |
| MX28_PAD_ENET0_RX_EN__ENET0_RX_EN |
| MX28_PAD_ENET0_RXD0__ENET0_RXD0 |
| MX28_PAD_ENET0_RXD1__ENET0_RXD1 |
| MX28_PAD_ENET0_TX_EN__ENET0_TX_EN |
| MX28_PAD_ENET0_TXD0__ENET0_TXD0 |
| MX28_PAD_ENET0_TXD1__ENET0_TXD1 |
| MX28_PAD_ENET_CLK__CLKCTRL_ENET |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mac1_pins_a: mac1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_ENET0_CRS__ENET1_RX_EN |
| MX28_PAD_ENET0_RXD2__ENET1_RXD0 |
| MX28_PAD_ENET0_RXD3__ENET1_RXD1 |
| MX28_PAD_ENET0_COL__ENET1_TX_EN |
| MX28_PAD_ENET0_TXD2__ENET1_TXD0 |
| MX28_PAD_ENET0_TXD3__ENET1_TXD1 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mmc0_8bit_pins_a: mmc0-8bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_DATA0__SSP0_D0 |
| MX28_PAD_SSP0_DATA1__SSP0_D1 |
| MX28_PAD_SSP0_DATA2__SSP0_D2 |
| MX28_PAD_SSP0_DATA3__SSP0_D3 |
| MX28_PAD_SSP0_DATA4__SSP0_D4 |
| MX28_PAD_SSP0_DATA5__SSP0_D5 |
| MX28_PAD_SSP0_DATA6__SSP0_D6 |
| MX28_PAD_SSP0_DATA7__SSP0_D7 |
| MX28_PAD_SSP0_CMD__SSP0_CMD |
| MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
| MX28_PAD_SSP0_SCK__SSP0_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mmc0_4bit_pins_a: mmc0-4bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_DATA0__SSP0_D0 |
| MX28_PAD_SSP0_DATA1__SSP0_D1 |
| MX28_PAD_SSP0_DATA2__SSP0_D2 |
| MX28_PAD_SSP0_DATA3__SSP0_D3 |
| MX28_PAD_SSP0_CMD__SSP0_CMD |
| MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
| MX28_PAD_SSP0_SCK__SSP0_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mmc0_cd_cfg: mmc0-cd-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
| >; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| mmc0_sck_cfg: mmc0-sck-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_SCK__SSP0_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| mmc1_4bit_pins_a: mmc1-4bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_D00__SSP1_D0 |
| MX28_PAD_GPMI_D01__SSP1_D1 |
| MX28_PAD_GPMI_D02__SSP1_D2 |
| MX28_PAD_GPMI_D03__SSP1_D3 |
| MX28_PAD_GPMI_RDY1__SSP1_CMD |
| MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT |
| MX28_PAD_GPMI_WRN__SSP1_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mmc1_cd_cfg: mmc1-cd-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT |
| >; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| mmc1_sck_cfg: mmc1-sck-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_WRN__SSP1_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| |
| mmc2_4bit_pins_a: mmc2-4bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_DATA4__SSP2_D0 |
| MX28_PAD_SSP1_SCK__SSP2_D1 |
| MX28_PAD_SSP1_CMD__SSP2_D2 |
| MX28_PAD_SSP0_DATA5__SSP2_D3 |
| MX28_PAD_SSP0_DATA6__SSP2_CMD |
| MX28_PAD_AUART1_RX__SSP2_CARD_DETECT |
| MX28_PAD_SSP0_DATA7__SSP2_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| mmc2_cd_cfg: mmc2-cd-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART1_RX__SSP2_CARD_DETECT |
| >; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| mmc2_sck_cfg: mmc2-sck-cfg { |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP0_DATA7__SSP2_SCK |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| i2c0_pins_a: i2c0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_I2C0_SCL__I2C0_SCL |
| MX28_PAD_I2C0_SDA__I2C0_SDA |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| i2c0_pins_b: i2c0@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART0_RX__I2C0_SCL |
| MX28_PAD_AUART0_TX__I2C0_SDA |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| i2c1_pins_a: i2c1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM0__I2C1_SCL |
| MX28_PAD_PWM1__I2C1_SDA |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| i2c1_pins_b: i2c1@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART2_CTS__I2C1_SCL |
| MX28_PAD_AUART2_RTS__I2C1_SDA |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| saif0_pins_a: saif0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
| MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
| MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
| MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| saif0_pins_b: saif0@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
| MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
| MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| saif1_pins_a: saif1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| pwm0_pins_a: pwm0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM0__PWM_0 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| pwm2_pins_a: pwm2@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM2__PWM_2 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| pwm3_pins_a: pwm3@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM3__PWM_3 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| pwm3_pins_b: pwm3@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SAIF0_MCLK__PWM_3 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| pwm4_pins_a: pwm4@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM4__PWM_4 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| lcdif_24bit_pins_a: lcdif-24bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_LCD_D00__LCD_D0 |
| MX28_PAD_LCD_D01__LCD_D1 |
| MX28_PAD_LCD_D02__LCD_D2 |
| MX28_PAD_LCD_D03__LCD_D3 |
| MX28_PAD_LCD_D04__LCD_D4 |
| MX28_PAD_LCD_D05__LCD_D5 |
| MX28_PAD_LCD_D06__LCD_D6 |
| MX28_PAD_LCD_D07__LCD_D7 |
| MX28_PAD_LCD_D08__LCD_D8 |
| MX28_PAD_LCD_D09__LCD_D9 |
| MX28_PAD_LCD_D10__LCD_D10 |
| MX28_PAD_LCD_D11__LCD_D11 |
| MX28_PAD_LCD_D12__LCD_D12 |
| MX28_PAD_LCD_D13__LCD_D13 |
| MX28_PAD_LCD_D14__LCD_D14 |
| MX28_PAD_LCD_D15__LCD_D15 |
| MX28_PAD_LCD_D16__LCD_D16 |
| MX28_PAD_LCD_D17__LCD_D17 |
| MX28_PAD_LCD_D18__LCD_D18 |
| MX28_PAD_LCD_D19__LCD_D19 |
| MX28_PAD_LCD_D20__LCD_D20 |
| MX28_PAD_LCD_D21__LCD_D21 |
| MX28_PAD_LCD_D22__LCD_D22 |
| MX28_PAD_LCD_D23__LCD_D23 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| lcdif_18bit_pins_a: lcdif-18bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_LCD_D00__LCD_D0 |
| MX28_PAD_LCD_D01__LCD_D1 |
| MX28_PAD_LCD_D02__LCD_D2 |
| MX28_PAD_LCD_D03__LCD_D3 |
| MX28_PAD_LCD_D04__LCD_D4 |
| MX28_PAD_LCD_D05__LCD_D5 |
| MX28_PAD_LCD_D06__LCD_D6 |
| MX28_PAD_LCD_D07__LCD_D7 |
| MX28_PAD_LCD_D08__LCD_D8 |
| MX28_PAD_LCD_D09__LCD_D9 |
| MX28_PAD_LCD_D10__LCD_D10 |
| MX28_PAD_LCD_D11__LCD_D11 |
| MX28_PAD_LCD_D12__LCD_D12 |
| MX28_PAD_LCD_D13__LCD_D13 |
| MX28_PAD_LCD_D14__LCD_D14 |
| MX28_PAD_LCD_D15__LCD_D15 |
| MX28_PAD_LCD_D16__LCD_D16 |
| MX28_PAD_LCD_D17__LCD_D17 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| lcdif_16bit_pins_a: lcdif-16bit@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_LCD_D00__LCD_D0 |
| MX28_PAD_LCD_D01__LCD_D1 |
| MX28_PAD_LCD_D02__LCD_D2 |
| MX28_PAD_LCD_D03__LCD_D3 |
| MX28_PAD_LCD_D04__LCD_D4 |
| MX28_PAD_LCD_D05__LCD_D5 |
| MX28_PAD_LCD_D06__LCD_D6 |
| MX28_PAD_LCD_D07__LCD_D7 |
| MX28_PAD_LCD_D08__LCD_D8 |
| MX28_PAD_LCD_D09__LCD_D9 |
| MX28_PAD_LCD_D10__LCD_D10 |
| MX28_PAD_LCD_D11__LCD_D11 |
| MX28_PAD_LCD_D12__LCD_D12 |
| MX28_PAD_LCD_D13__LCD_D13 |
| MX28_PAD_LCD_D14__LCD_D14 |
| MX28_PAD_LCD_D15__LCD_D15 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| lcdif_sync_pins_a: lcdif-sync@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_LCD_RS__LCD_DOTCLK |
| MX28_PAD_LCD_CS__LCD_ENABLE |
| MX28_PAD_LCD_RD_E__LCD_VSYNC |
| MX28_PAD_LCD_WR_RWN__LCD_HSYNC |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| can0_pins_a: can0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_RDY2__CAN0_TX |
| MX28_PAD_GPMI_RDY3__CAN0_RX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| can1_pins_a: can1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_GPMI_CE2N__CAN1_TX |
| MX28_PAD_GPMI_CE3N__CAN1_RX |
| >; |
| fsl,drive-strength = <MXS_DRIVE_4mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| spi2_pins_a: spi2@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP2_SCK__SSP2_SCK |
| MX28_PAD_SSP2_MOSI__SSP2_CMD |
| MX28_PAD_SSP2_MISO__SSP2_D0 |
| MX28_PAD_SSP2_SS0__SSP2_D3 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| spi3_pins_a: spi3@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART2_RX__SSP3_D4 |
| MX28_PAD_AUART2_TX__SSP3_D5 |
| MX28_PAD_SSP3_SCK__SSP3_SCK |
| MX28_PAD_SSP3_MOSI__SSP3_CMD |
| MX28_PAD_SSP3_MISO__SSP3_D0 |
| MX28_PAD_SSP3_SS0__SSP3_D3 |
| >; |
| fsl,drive-strength = <MXS_DRIVE_8mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| usb0_pins_a: usb0@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP2_SS2__USB0_OVERCURRENT |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| usb0_pins_b: usb0@1 { |
| reg = <1>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART1_CTS__USB0_OVERCURRENT |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| usb1_pins_a: usb1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_SSP2_SS1__USB1_OVERCURRENT |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_DISABLE>; |
| }; |
| |
| usb0_id_pins_a: usb0id@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_AUART1_RTS__USB0_ID |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| usb0_id_pins_b: usb0id1@0 { |
| reg = <0>; |
| fsl,pinmux-ids = < |
| MX28_PAD_PWM2__USB0_ID |
| >; |
| fsl,drive-strength = <MXS_DRIVE_12mA>; |
| fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| fsl,pull-up = <MXS_PULL_ENABLE>; |
| }; |
| |
| }; |
| |
| digctl: digctl@8001c000 { |
| compatible = "fsl,imx28-digctl", "fsl,imx23-digctl"; |
| reg = <0x8001c000 0x2000>; |
| interrupts = <89>; |
| status = "disabled"; |
| }; |
| |
| etm: etm@80022000 { |
| reg = <0x80022000 0x2000>; |
| status = "disabled"; |
| }; |
| |
| dma_apbx: dma-apbx@80024000 { |
| compatible = "fsl,imx28-dma-apbx"; |
| reg = <0x80024000 0x2000>; |
| interrupts = <78 79 66 0 |
| 80 81 68 69 |
| 70 71 72 73 |
| 74 75 76 77>; |
| interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", |
| "saif0", "saif1", "i2c0", "i2c1", |
| "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", |
| "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; |
| #dma-cells = <1>; |
| dma-channels = <16>; |
| clocks = <&clks 26>; |
| }; |
| |
| dcp: dcp@80028000 { |
| compatible = "fsl,imx28-dcp", "fsl,imx23-dcp"; |
| reg = <0x80028000 0x2000>; |
| interrupts = <52 53 54>; |
| status = "okay"; |
| }; |
| |
| pxp: pxp@8002a000 { |
| reg = <0x8002a000 0x2000>; |
| interrupts = <39>; |
| status = "disabled"; |
| }; |
| |
| ocotp: ocotp@8002c000 { |
| compatible = "fsl,ocotp"; |
| reg = <0x8002c000 0x2000>; |
| status = "disabled"; |
| }; |
| |
| axi-ahb@8002e000 { |
| reg = <0x8002e000 0x2000>; |
| status = "disabled"; |
| }; |
| |
| lcdif: lcdif@80030000 { |
| compatible = "fsl,imx28-lcdif"; |
| reg = <0x80030000 0x2000>; |
| interrupts = <38>; |
| clocks = <&clks 55>; |
| dmas = <&dma_apbh 13>; |
| dma-names = "rx"; |
| status = "disabled"; |
| }; |
| |
| can0: can@80032000 { |
| compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan"; |
| reg = <0x80032000 0x2000>; |
| interrupts = <8>; |
| clocks = <&clks 58>, <&clks 58>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| can1: can@80034000 { |
| compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan"; |
| reg = <0x80034000 0x2000>; |
| interrupts = <9>; |
| clocks = <&clks 59>, <&clks 59>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| simdbg: simdbg@8003c000 { |
| reg = <0x8003c000 0x200>; |
| status = "disabled"; |
| }; |
| |
| simgpmisel: simgpmisel@8003c200 { |
| reg = <0x8003c200 0x100>; |
| status = "disabled"; |
| }; |
| |
| simsspsel: simsspsel@8003c300 { |
| reg = <0x8003c300 0x100>; |
| status = "disabled"; |
| }; |
| |
| simmemsel: simmemsel@8003c400 { |
| reg = <0x8003c400 0x100>; |
| status = "disabled"; |
| }; |
| |
| gpiomon: gpiomon@8003c500 { |
| reg = <0x8003c500 0x100>; |
| status = "disabled"; |
| }; |
| |
| simenet: simenet@8003c700 { |
| reg = <0x8003c700 0x100>; |
| status = "disabled"; |
| }; |
| |
| armjtag: armjtag@8003c800 { |
| reg = <0x8003c800 0x100>; |
| status = "disabled"; |
| }; |
| }; |
| |
| apbx@80040000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x80040000 0x40000>; |
| ranges; |
| |
| clks: clkctrl@80040000 { |
| compatible = "fsl,imx28-clkctrl", "fsl,clkctrl"; |
| reg = <0x80040000 0x2000>; |
| #clock-cells = <1>; |
| }; |
| |
| saif0: saif@80042000 { |
| compatible = "fsl,imx28-saif"; |
| reg = <0x80042000 0x2000>; |
| interrupts = <59>; |
| #clock-cells = <0>; |
| clocks = <&clks 53>; |
| dmas = <&dma_apbx 4>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| power: power@80044000 { |
| reg = <0x80044000 0x2000>; |
| status = "disabled"; |
| }; |
| |
| saif1: saif@80046000 { |
| compatible = "fsl,imx28-saif"; |
| reg = <0x80046000 0x2000>; |
| interrupts = <58>; |
| clocks = <&clks 54>; |
| dmas = <&dma_apbx 5>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| lradc: lradc@80050000 { |
| compatible = "fsl,imx28-lradc"; |
| reg = <0x80050000 0x2000>; |
| interrupts = <10 14 15 16 17 18 19 |
| 20 21 22 23 24 25>; |
| status = "disabled"; |
| clocks = <&clks 41>; |
| #io-channel-cells = <1>; |
| }; |
| |
| spdif: spdif@80054000 { |
| reg = <0x80054000 0x2000>; |
| interrupts = <45>; |
| dmas = <&dma_apbx 2>; |
| dma-names = "tx"; |
| status = "disabled"; |
| }; |
| |
| mxs_rtc: rtc@80056000 { |
| compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; |
| reg = <0x80056000 0x2000>; |
| interrupts = <29>; |
| }; |
| |
| i2c0: i2c@80058000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx28-i2c"; |
| reg = <0x80058000 0x2000>; |
| interrupts = <111>; |
| clock-frequency = <100000>; |
| dmas = <&dma_apbx 6>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@8005a000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx28-i2c"; |
| reg = <0x8005a000 0x2000>; |
| interrupts = <110>; |
| clock-frequency = <100000>; |
| dmas = <&dma_apbx 7>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| pwm: pwm@80064000 { |
| compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; |
| reg = <0x80064000 0x2000>; |
| clocks = <&clks 44>; |
| #pwm-cells = <2>; |
| fsl,pwm-number = <8>; |
| status = "disabled"; |
| }; |
| |
| timer: timrot@80068000 { |
| compatible = "fsl,imx28-timrot", "fsl,timrot"; |
| reg = <0x80068000 0x2000>; |
| interrupts = <48 49 50 51>; |
| clocks = <&clks 26>; |
| }; |
| |
| auart0: serial@8006a000 { |
| compatible = "fsl,imx28-auart", "fsl,imx23-auart"; |
| reg = <0x8006a000 0x2000>; |
| interrupts = <112>; |
| dmas = <&dma_apbx 8>, <&dma_apbx 9>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks 45>; |
| status = "disabled"; |
| }; |
| |
| auart1: serial@8006c000 { |
| compatible = "fsl,imx28-auart", "fsl,imx23-auart"; |
| reg = <0x8006c000 0x2000>; |
| interrupts = <113>; |
| dmas = <&dma_apbx 10>, <&dma_apbx 11>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks 45>; |
| status = "disabled"; |
| }; |
| |
| auart2: serial@8006e000 { |
| compatible = "fsl,imx28-auart", "fsl,imx23-auart"; |
| reg = <0x8006e000 0x2000>; |
| interrupts = <114>; |
| dmas = <&dma_apbx 12>, <&dma_apbx 13>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks 45>; |
| status = "disabled"; |
| }; |
| |
| auart3: serial@80070000 { |
| compatible = "fsl,imx28-auart", "fsl,imx23-auart"; |
| reg = <0x80070000 0x2000>; |
| interrupts = <115>; |
| dmas = <&dma_apbx 14>, <&dma_apbx 15>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks 45>; |
| status = "disabled"; |
| }; |
| |
| auart4: serial@80072000 { |
| compatible = "fsl,imx28-auart", "fsl,imx23-auart"; |
| reg = <0x80072000 0x2000>; |
| interrupts = <116>; |
| dmas = <&dma_apbx 0>, <&dma_apbx 1>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks 45>; |
| status = "disabled"; |
| }; |
| |
| duart: serial@80074000 { |
| compatible = "arm,pl011", "arm,primecell"; |
| reg = <0x80074000 0x1000>; |
| interrupts = <47>; |
| clocks = <&clks 45>, <&clks 26>; |
| clock-names = "uart", "apb_pclk"; |
| status = "disabled"; |
| }; |
| |
| usbphy0: usbphy@8007c000 { |
| compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x8007c000 0x2000>; |
| clocks = <&clks 62>; |
| status = "disabled"; |
| }; |
| |
| usbphy1: usbphy@8007e000 { |
| compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x8007e000 0x2000>; |
| clocks = <&clks 63>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| ahb@80080000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x80080000 0x80000>; |
| ranges; |
| |
| usb0: usb@80080000 { |
| compatible = "fsl,imx28-usb", "fsl,imx27-usb"; |
| reg = <0x80080000 0x10000>; |
| interrupts = <93>; |
| clocks = <&clks 60>; |
| fsl,usbphy = <&usbphy0>; |
| status = "disabled"; |
| }; |
| |
| usb1: usb@80090000 { |
| compatible = "fsl,imx28-usb", "fsl,imx27-usb"; |
| reg = <0x80090000 0x10000>; |
| interrupts = <92>; |
| clocks = <&clks 61>; |
| fsl,usbphy = <&usbphy1>; |
| status = "disabled"; |
| }; |
| |
| dflpt: dflpt@800c0000 { |
| reg = <0x800c0000 0x10000>; |
| status = "disabled"; |
| }; |
| |
| mac0: ethernet@800f0000 { |
| compatible = "fsl,imx28-fec"; |
| reg = <0x800f0000 0x4000>; |
| interrupts = <101>; |
| clocks = <&clks 57>, <&clks 57>, <&clks 64>; |
| clock-names = "ipg", "ahb", "enet_out"; |
| status = "disabled"; |
| }; |
| |
| mac1: ethernet@800f4000 { |
| compatible = "fsl,imx28-fec"; |
| reg = <0x800f4000 0x4000>; |
| interrupts = <102>; |
| clocks = <&clks 57>, <&clks 57>; |
| clock-names = "ipg", "ahb"; |
| status = "disabled"; |
| }; |
| |
| etn_switch: switch@800f8000 { |
| reg = <0x800f8000 0x8000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| iio_hwmon { |
| compatible = "iio-hwmon"; |
| io-channels = <&lradc 8>; |
| }; |
| }; |