Merge remote-tracking branch 'spi/topic/atmel' into spi-next
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index d4ac60b..273db0b 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -170,18 +170,18 @@
/* Bit manipulation macros */
#define SPI_BIT(name) \
(1 << SPI_##name##_OFFSET)
-#define SPI_BF(name,value) \
+#define SPI_BF(name, value) \
(((value) & ((1 << SPI_##name##_SIZE) - 1)) << SPI_##name##_OFFSET)
-#define SPI_BFEXT(name,value) \
+#define SPI_BFEXT(name, value) \
(((value) >> SPI_##name##_OFFSET) & ((1 << SPI_##name##_SIZE) - 1))
-#define SPI_BFINS(name,value,old) \
- ( ((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
- | SPI_BF(name,value))
+#define SPI_BFINS(name, value, old) \
+ (((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
+ | SPI_BF(name, value))
/* Register access macros */
-#define spi_readl(port,reg) \
+#define spi_readl(port, reg) \
__raw_readl((port)->regs + SPI_##reg)
-#define spi_writel(port,reg,value) \
+#define spi_writel(port, reg, value) \
__raw_writel((value), (port)->regs + SPI_##reg)
/* use PIO for small transfers, avoiding DMA setup/teardown overhead and
@@ -1401,8 +1401,8 @@
asd = spi->controller_state;
bits = (asd->csr >> 4) & 0xf;
if (bits != xfer->bits_per_word - 8) {
- dev_dbg(&spi->dev, "you can't yet change "
- "bits_per_word in transfers\n");
+ dev_dbg(&spi->dev,
+ "you can't yet change bits_per_word in transfers\n");
return -ENOPROTOOPT;
}
}
@@ -1516,7 +1516,7 @@
/* setup spi core then atmel-specific driver state */
ret = -ENOMEM;
- master = spi_alloc_master(&pdev->dev, sizeof *as);
+ master = spi_alloc_master(&pdev->dev, sizeof(*as));
if (!master)
goto out_free;
@@ -1546,9 +1546,11 @@
INIT_LIST_HEAD(&as->queue);
as->pdev = pdev;
- as->regs = ioremap(regs->start, resource_size(regs));
- if (!as->regs)
+ as->regs = devm_ioremap_resource(&pdev->dev, regs);
+ if (IS_ERR(as->regs)) {
+ ret = PTR_ERR(as->regs);
goto out_free_buffer;
+ }
as->phybase = regs->start;
as->irq = irq;
as->clk = clk;
@@ -1617,7 +1619,6 @@
out_free_irq:
free_irq(irq, master);
out_unmap_regs:
- iounmap(as->regs);
out_free_buffer:
if (!as->use_pdc)
tasklet_kill(&as->tasklet);
@@ -1669,36 +1670,36 @@
clk_disable_unprepare(as->clk);
clk_put(as->clk);
free_irq(as->irq, master);
- iounmap(as->regs);
spi_unregister_master(master);
return 0;
}
-#ifdef CONFIG_PM
-
-static int atmel_spi_suspend(struct platform_device *pdev, pm_message_t mesg)
+#ifdef CONFIG_PM_SLEEP
+static int atmel_spi_suspend(struct device *dev)
{
- struct spi_master *master = platform_get_drvdata(pdev);
+ struct spi_master *master = dev_get_drvdata(dev);
struct atmel_spi *as = spi_master_get_devdata(master);
clk_disable_unprepare(as->clk);
return 0;
}
-static int atmel_spi_resume(struct platform_device *pdev)
+static int atmel_spi_resume(struct device *dev)
{
- struct spi_master *master = platform_get_drvdata(pdev);
+ struct spi_master *master = dev_get_drvdata(dev);
struct atmel_spi *as = spi_master_get_devdata(master);
- return clk_prepare_enable(as->clk);
+ clk_prepare_enable(as->clk);
return 0;
}
+static SIMPLE_DEV_PM_OPS(atmel_spi_pm_ops, atmel_spi_suspend, atmel_spi_resume);
+
+#define ATMEL_SPI_PM_OPS (&atmel_spi_pm_ops)
#else
-#define atmel_spi_suspend NULL
-#define atmel_spi_resume NULL
+#define ATMEL_SPI_PM_OPS NULL
#endif
#if defined(CONFIG_OF)
@@ -1714,10 +1715,9 @@
.driver = {
.name = "atmel_spi",
.owner = THIS_MODULE,
+ .pm = ATMEL_SPI_PM_OPS,
.of_match_table = of_match_ptr(atmel_spi_dt_ids),
},
- .suspend = atmel_spi_suspend,
- .resume = atmel_spi_resume,
.probe = atmel_spi_probe,
.remove = atmel_spi_remove,
};
diff --git a/drivers/spi/spi-bfin-sport.c b/drivers/spi/spi-bfin-sport.c
index 91921b5..7b2cda0 100644
--- a/drivers/spi/spi-bfin-sport.c
+++ b/drivers/spi/spi-bfin-sport.c
@@ -592,7 +592,7 @@
*/
if (chip_info->ctl_reg || chip_info->enable_dma) {
ret = -EINVAL;
- dev_err(&spi->dev, "don't set ctl_reg/enable_dma fields");
+ dev_err(&spi->dev, "don't set ctl_reg/enable_dma fields\n");
goto error;
}
chip->cs_chg_udelay = chip_info->cs_chg_udelay;
diff --git a/drivers/spi/spi-bfin5xx.c b/drivers/spi/spi-bfin5xx.c
index 45bdf73..b70a2bd 100644
--- a/drivers/spi/spi-bfin5xx.c
+++ b/drivers/spi/spi-bfin5xx.c
@@ -524,7 +524,7 @@
timeout = jiffies + HZ;
while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_SPIF))
if (!time_before(jiffies, timeout)) {
- dev_warn(&drv_data->pdev->dev, "timeout waiting for SPIF");
+ dev_warn(&drv_data->pdev->dev, "timeout waiting for SPIF\n");
break;
} else
cpu_relax();
@@ -913,8 +913,9 @@
drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
struct spi_transfer, transfer_list);
- dev_dbg(&drv_data->pdev->dev, "got a message to pump, "
- "state is set to: baud %d, flag 0x%x, ctl 0x%x\n",
+ dev_dbg(&drv_data->pdev->dev,
+ "got a message to pump, state is set to: baud "
+ "%d, flag 0x%x, ctl 0x%x\n",
drv_data->cur_chip->baud, drv_data->cur_chip->flag,
drv_data->cur_chip->ctl_reg);
@@ -1013,8 +1014,8 @@
* but let's assume (for now) they do.
*/
if (chip_info->ctl_reg & ~bfin_ctl_reg) {
- dev_err(&spi->dev, "do not set bits in ctl_reg "
- "that the SPI framework manages\n");
+ dev_err(&spi->dev,
+ "do not set bits in ctl_reg that the SPI framework manages\n");
goto error;
}
chip->enable_dma = chip_info->enable_dma != 0
@@ -1050,17 +1051,17 @@
chip->chip_select_num = spi->chip_select;
if (chip->chip_select_num < MAX_CTRL_CS) {
if (!(spi->mode & SPI_CPHA))
- dev_warn(&spi->dev, "Warning: SPI CPHA not set:"
- " Slave Select not under software control!\n"
- " See Documentation/blackfin/bfin-spi-notes.txt");
+ dev_warn(&spi->dev,
+ "Warning: SPI CPHA not set: Slave Select not under software control!\n"
+ "See Documentation/blackfin/bfin-spi-notes.txt\n");
chip->flag = (1 << spi->chip_select) << 8;
} else
chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
if (chip->enable_dma && chip->pio_interrupt) {
- dev_err(&spi->dev, "enable_dma is set, "
- "do not set pio_interrupt\n");
+ dev_err(&spi->dev,
+ "enable_dma is set, do not set pio_interrupt\n");
goto error;
}
/*
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 79c958e..b897c4ad 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -870,8 +870,8 @@
/* Remove the queue */
status = destroy_queue(dws);
if (status != 0)
- dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not "
- "complete, message memory not freed\n");
+ dev_err(&dws->master->dev,
+ "dw_spi_remove: workqueue will not complete, message memory not freed\n");
if (dws->dma_ops && dws->dma_ops->dma_exit)
dws->dma_ops->dma_exit(dws);
diff --git a/drivers/spi/spi-ep93xx.c b/drivers/spi/spi-ep93xx.c
index d22c00a..b57a341 100644
--- a/drivers/spi/spi-ep93xx.c
+++ b/drivers/spi/spi-ep93xx.c
@@ -330,7 +330,7 @@
dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n",
chip->spi->mode, div_cpsr, div_scr, dss);
- dev_dbg(&espi->pdev->dev, "setup: cr0 %#x", cr0);
+ dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0);
ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr);
ep93xx_spi_write_u16(espi, SSPCR0, cr0);
@@ -509,7 +509,7 @@
}
if (WARN_ON(len)) {
- dev_warn(&espi->pdev->dev, "len = %zu expected 0!", len);
+ dev_warn(&espi->pdev->dev, "len = %zu expected 0!\n", len);
return ERR_PTR(-EINVAL);
}
diff --git a/drivers/spi/spi-fsl-cpm.c b/drivers/spi/spi-fsl-cpm.c
index 07971e3..58630ed 100644
--- a/drivers/spi/spi-fsl-cpm.c
+++ b/drivers/spi/spi-fsl-cpm.c
@@ -299,7 +299,7 @@
switch (mspi->subblock) {
default:
- dev_warn(dev, "cell-index unspecified, assuming SPI1");
+ dev_warn(dev, "cell-index unspecified, assuming SPI1\n");
/* fall through */
case 0:
mspi->subblock = QE_CR_SUBBLOCK_SPI1;
diff --git a/drivers/spi/spi-fsl-espi.c b/drivers/spi/spi-fsl-espi.c
index b8f1103..43222d7 100644
--- a/drivers/spi/spi-fsl-espi.c
+++ b/drivers/spi/spi-fsl-espi.c
@@ -289,8 +289,8 @@
if ((first->bits_per_word != t->bits_per_word) ||
(first->speed_hz != t->speed_hz)) {
espi_trans->status = -EINVAL;
- dev_err(mspi->dev, "bits_per_word/speed_hz should be"
- " same for the same SPI transfer\n");
+ dev_err(mspi->dev,
+ "bits_per_word/speed_hz should be same for the same SPI transfer\n");
return;
}
diff --git a/drivers/spi/spi-mpc52xx-psc.c b/drivers/spi/spi-mpc52xx-psc.c
index 6e925dc..00ba910 100644
--- a/drivers/spi/spi-mpc52xx-psc.c
+++ b/drivers/spi/spi-mpc52xx-psc.c
@@ -383,8 +383,8 @@
mps->irq = irq;
if (pdata == NULL) {
- dev_warn(dev, "probe called without platform data, no "
- "cs_control function will be called\n");
+ dev_warn(dev,
+ "probe called without platform data, no cs_control function will be called\n");
mps->cs_control = NULL;
mps->sysclk = 0;
master->bus_num = bus_num;
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 32dca0c..c4e4868 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -504,7 +504,7 @@
((u32 *)xfer->rx_buf)[elements++] = w;
} else {
int bytes_per_word = mcspi_bytes_per_word(word_len);
- dev_err(&spi->dev, "DMA RX penultimate word empty");
+ dev_err(&spi->dev, "DMA RX penultimate word empty\n");
count -= (bytes_per_word << 1);
omap2_mcspi_set_enable(spi, 1);
return count;
@@ -522,7 +522,7 @@
else /* word_len <= 32 */
((u32 *)xfer->rx_buf)[elements] = w;
} else {
- dev_err(&spi->dev, "DMA RX last word empty");
+ dev_err(&spi->dev, "DMA RX last word empty\n");
count -= mcspi_bytes_per_word(word_len);
}
omap2_mcspi_set_enable(spi, 1);
diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index c1a5067..64e1682 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -573,8 +573,8 @@
write_SSTO(0, reg);
write_SSSR_CS(drv_data, drv_data->clear_sr);
- dev_err(&drv_data->pdev->dev, "bad message state "
- "in interrupt handler\n");
+ dev_err(&drv_data->pdev->dev,
+ "bad message state in interrupt handler\n");
/* Never fail */
return IRQ_HANDLED;
@@ -651,8 +651,8 @@
if (message->is_dma_mapped
|| transfer->rx_dma || transfer->tx_dma) {
dev_err(&drv_data->pdev->dev,
- "pump_transfers: mapped transfer length "
- "of %u is greater than %d\n",
+ "pump_transfers: mapped transfer length of "
+ "%u is greater than %d\n",
transfer->len, MAX_DMA_LEN);
message->status = -EINVAL;
giveback(drv_data);
@@ -660,11 +660,10 @@
}
/* warn ... we force this to PIO mode */
- if (printk_ratelimit())
- dev_warn(&message->spi->dev, "pump_transfers: "
- "DMA disabled for transfer length %ld "
- "greater than %d\n",
- (long)drv_data->len, MAX_DMA_LEN);
+ dev_warn_ratelimited(&message->spi->dev,
+ "pump_transfers: DMA disabled for transfer length %ld "
+ "greater than %d\n",
+ (long)drv_data->len, MAX_DMA_LEN);
}
/* Setup the transfer state based on the type of transfer */
@@ -726,11 +725,8 @@
message->spi,
bits, &dma_burst,
&dma_thresh))
- if (printk_ratelimit())
- dev_warn(&message->spi->dev,
- "pump_transfers: "
- "DMA burst size reduced to "
- "match bits_per_word\n");
+ dev_warn_ratelimited(&message->spi->dev,
+ "pump_transfers: DMA burst size reduced to match bits_per_word\n");
}
cr0 = clk_div
@@ -854,8 +850,8 @@
if (gpio_is_valid(chip_info->gpio_cs)) {
err = gpio_request(chip_info->gpio_cs, "SPI_CS");
if (err) {
- dev_err(&spi->dev, "failed to request chip select "
- "GPIO%d\n", chip_info->gpio_cs);
+ dev_err(&spi->dev, "failed to request chip select GPIO%d\n",
+ chip_info->gpio_cs);
return err;
}
@@ -899,8 +895,8 @@
if (drv_data->ssp_type == CE4100_SSP) {
if (spi->chip_select > 4) {
- dev_err(&spi->dev, "failed setup: "
- "cs number must not be > 4.\n");
+ dev_err(&spi->dev,
+ "failed setup: cs number must not be > 4.\n");
kfree(chip);
return -EINVAL;
}
@@ -956,8 +952,8 @@
spi->bits_per_word,
&chip->dma_burst_size,
&chip->dma_threshold)) {
- dev_warn(&spi->dev, "in setup: DMA burst size reduced "
- "to match bits_per_word\n");
+ dev_warn(&spi->dev,
+ "in setup: DMA burst size reduced to match bits_per_word\n");
}
}
diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c
index eaeeed5..14843ef 100644
--- a/drivers/spi/spi-topcliff-pch.c
+++ b/drivers/spi/spi-topcliff-pch.c
@@ -506,8 +506,8 @@
goto err_out;
}
- dev_dbg(&pspi->dev, "%s Transfer List not empty. "
- "Transfer Speed is set.\n", __func__);
+ dev_dbg(&pspi->dev,
+ "%s Transfer List not empty. Transfer Speed is set.\n", __func__);
spin_lock_irqsave(&data->lock, flags);
/* validate Tx/Rx buffers and Transfer length */
@@ -526,8 +526,9 @@
goto err_return_spinlock;
}
- dev_dbg(&pspi->dev, "%s Tx/Rx buffer valid. Transfer length"
- " valid\n", __func__);
+ dev_dbg(&pspi->dev,
+ "%s Tx/Rx buffer valid. Transfer length valid\n",
+ __func__);
/* if baud rate has been specified validate the same */
if (transfer->speed_hz > PCH_MAX_BAUDRATE)
@@ -1181,8 +1182,8 @@
spin_lock(&data->lock);
/* check if suspend has been initiated;if yes flush queue */
if (data->board_dat->suspend_sts || (data->status == STATUS_EXITING)) {
- dev_dbg(&data->master->dev, "%s suspend/remove initiated,"
- "flushing queue\n", __func__);
+ dev_dbg(&data->master->dev,
+ "%s suspend/remove initiated, flushing queue\n", __func__);
list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) {
pmsg->status = -EIO;