Blackfin arch: add support for Blackfin latest processor family BF51x
Signed-off-by: Bryan Wu <cooloney@kernel.org>
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index be54e36..19b43f3 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -77,6 +77,26 @@
prompt "CPU"
default BF533
+config BF512
+ bool "BF512"
+ help
+ BF512 Processor Support.
+
+config BF514
+ bool "BF514"
+ help
+ BF514 Processor Support.
+
+config BF516
+ bool "BF516"
+ help
+ BF516 Processor Support.
+
+config BF518
+ bool "BF518"
+ help
+ BF518 Processor Support.
+
config BF522
bool "BF522"
help
@@ -181,27 +201,27 @@
config BF_REV_MIN
int
- default 0 if (BF52x || BF54x)
+ default 0 if (BF51x || BF52x || BF54x)
default 2 if (BF537 || BF536 || BF534)
default 3 if (BF561 ||BF533 || BF532 || BF531)
- default 4 if (BF538 || BF539)
+ default 4 if (BF538 || BF539)
config BF_REV_MAX
int
- default 2 if (BF52x || BF54x)
+ default 2 if (BF51x || BF52x || BF54x)
default 3 if (BF537 || BF536 || BF534)
- default 5 if (BF561|| BF538 || BF539)
+ default 5 if (BF561 || BF538 || BF539)
default 6 if (BF533 || BF532 || BF531)
choice
prompt "Silicon Rev"
- default BF_REV_0_1 if (BF52x || BF54x)
+ default BF_REV_0_1 if (BF51x || BF52x || BF54x)
default BF_REV_0_2 if (BF534 || BF536 || BF537)
default BF_REV_0_3 if (BF531 || BF532 || BF533 || BF561)
config BF_REV_0_0
bool "0.0"
- depends on (BF52x || BF54x)
+ depends on (BF51x || BF52x || BF54x)
config BF_REV_0_1
bool "0.1"
@@ -235,6 +255,11 @@
endchoice
+config BF51x
+ bool
+ depends on (BF512 || BF514 || BF516 || BF518)
+ default y
+
config BF52x
bool
depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527)
@@ -282,6 +307,7 @@
depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP || BFIN526_EZBRD)
default y
+source "arch/blackfin/mach-bf518/Kconfig"
source "arch/blackfin/mach-bf527/Kconfig"
source "arch/blackfin/mach-bf533/Kconfig"
source "arch/blackfin/mach-bf561/Kconfig"
@@ -330,7 +356,7 @@
int "Frequency of the crystal on the board in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
- default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT)
+ default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT || BFIN518F-EZBRD)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
default "10000000" if BFIN532_IP0X
@@ -370,7 +396,7 @@
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
- default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
+ default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
@@ -432,6 +458,10 @@
#
config MAX_VCO_HZ
int
+ default 400000000 if BF512
+ default 400000000 if BF514
+ default 400000000 if BF516
+ default 400000000 if BF518
default 600000000 if BF522
default 400000000 if BF523
default 400000000 if BF524
@@ -1025,7 +1055,7 @@
config PM_BFIN_WAKE_PH6
bool "Allow Wake-Up from on-chip PHY or PH6 GP"
- depends on PM && (BF52x || BF534 || BF536 || BF537)
+ depends on PM && (BF51x || BF52x || BF534 || BF536 || BF537)
default n
help
Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up)