[PATCH] hwmon: hwmon vs i2c, second round (07/11)
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 6483ff6..35fe7d1 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -19,10 +19,13 @@
This support can also be built as a module. If so, the module
will be called hwmon.
+config HWMON_VID
+ tristate
+ default n
+
config SENSORS_ADM1021
tristate "Analog Devices ADM1021 and compatibles"
depends on HWMON && I2C
- select I2C_SENSOR
help
If you say yes here you get support for Analog Devices ADM1021
and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A,
@@ -35,7 +38,7 @@
config SENSORS_ADM1025
tristate "Analog Devices ADM1025 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1025
and Philips NE1619 sensor chips.
@@ -46,7 +49,7 @@
config SENSORS_ADM1026
tristate "Analog Devices ADM1026 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1026
sensor chip.
@@ -57,7 +60,6 @@
config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for Analog Devices ADM1031
and ADM1030 sensor chips.
@@ -68,7 +70,7 @@
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
Dallas DS1780, National Semiconductor LM81 sensor chips.
@@ -79,7 +81,7 @@
config SENSORS_ASB100
tristate "Asus ASB100 Bach"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for the ASB100 Bach sensor
chip found on some Asus mainboards.
@@ -90,7 +92,7 @@
config SENSORS_ATXP1
tristate "Attansic ATXP1 VID controller"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for the Attansic ATXP1 VID
controller.
@@ -104,7 +106,6 @@
config SENSORS_DS1621
tristate "Dallas Semiconductor DS1621 and DS1625"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for Dallas Semiconductor
DS1621 and DS1625 sensor chips.
@@ -115,7 +116,6 @@
config SENSORS_FSCHER
tristate "FSC Hermes"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for Fujitsu Siemens
Computers Hermes sensor chips.
@@ -126,7 +126,6 @@
config SENSORS_FSCPOS
tristate "FSC Poseidon"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for Fujitsu Siemens
Computers Poseidon sensor chips.
@@ -137,7 +136,6 @@
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
depends on HWMON && I2C
- select I2C_SENSOR
help
If you say yes here you get support for Genesys Logic GL518SM
sensor chips.
@@ -148,7 +146,7 @@
config SENSORS_GL520SM
tristate "Genesys Logic GL520SM"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for Genesys Logic GL520SM
sensor chips.
@@ -159,8 +157,8 @@
config SENSORS_IT87
tristate "ITE IT87xx and compatibles"
depends on HWMON && I2C
- select I2C_SENSOR
select I2C_ISA
+ select HWMON_VID
help
If you say yes here you get support for ITE IT87xx sensor chips
and clones: SiS960.
@@ -171,7 +169,6 @@
config SENSORS_LM63
tristate "National Semiconductor LM63"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for the National Semiconductor
LM63 remote diode digital temperature sensor with integrated fan
@@ -184,7 +181,6 @@
config SENSORS_LM75
tristate "National Semiconductor LM75 and compatibles"
depends on HWMON && I2C
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor LM75
sensor chips and clones: Dallas Semiconductor DS75 and DS1775 (in
@@ -200,7 +196,6 @@
config SENSORS_LM77
tristate "National Semiconductor LM77"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor LM77
sensor chips.
@@ -211,7 +206,6 @@
config SENSORS_LM78
tristate "National Semiconductor LM78 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get support for National Semiconductor LM78,
@@ -223,7 +217,6 @@
config SENSORS_LM80
tristate "National Semiconductor LM80"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor
LM80 sensor chips.
@@ -234,7 +227,6 @@
config SENSORS_LM83
tristate "National Semiconductor LM83"
depends on HWMON && I2C
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor
LM83 sensor chips.
@@ -245,7 +237,7 @@
config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADT7463, EMC6D100, EMC6D102 and ADM1027.
@@ -256,7 +248,7 @@
config SENSORS_LM87
tristate "National Semiconductor LM87"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
+ select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM87
sensor chips.
@@ -267,7 +259,6 @@
config SENSORS_LM90
tristate "National Semiconductor LM90 and compatibles"
depends on HWMON && I2C
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor LM90,
LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657 and
@@ -282,7 +273,6 @@
config SENSORS_LM92
tristate "National Semiconductor LM92 and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for National Semiconductor LM92
and Maxim MAX6635 sensor chips.
@@ -293,7 +283,6 @@
config SENSORS_MAX1619
tristate "Maxim MAX1619 sensor chip"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for MAX1619 sensor chip.
@@ -303,8 +292,8 @@
config SENSORS_PC87360
tristate "National Semiconductor PC87360 family"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
+ select HWMON_VID
help
If you say yes here you get access to the hardware monitoring
functions of the National Semiconductor PC8736x Super-I/O chips.
@@ -318,7 +307,6 @@
config SENSORS_SIS5595
tristate "Silicon Integrated Systems Corp. SiS5595"
depends on HWMON && I2C && PCI && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get support for the integrated sensors in
@@ -330,7 +318,6 @@
config SENSORS_SMSC47M1
tristate "SMSC LPC47M10x and compatibles"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get support for the integrated fan
@@ -343,7 +330,6 @@
config SENSORS_SMSC47B397
tristate "SMSC LPC47B397-NC"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get support for the SMSC LPC47B397-NC
@@ -355,7 +341,6 @@
config SENSORS_VIA686A
tristate "VIA686A"
depends on HWMON && I2C && PCI
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get support for the integrated sensors in
@@ -367,8 +352,8 @@
config SENSORS_W83781D
tristate "Winbond W83781D, W83782D, W83783S, W83627HF, Asus AS99127F"
depends on HWMON && I2C
- select I2C_SENSOR
select I2C_ISA
+ select HWMON_VID
help
If you say yes here you get support for the Winbond W8378x series
of sensor chips: the W83781D, W83782D, W83783S and W83627HF,
@@ -380,7 +365,6 @@
config SENSORS_W83792D
tristate "Winbond W83792D"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for the Winbond W83792D chip.
@@ -390,7 +374,6 @@
config SENSORS_W83L785TS
tristate "Winbond W83L785TS-S"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
help
If you say yes here you get support for the Winbond W83L785TS-S
sensor chip, which is used on the Asus A7N8X, among other
@@ -402,8 +385,8 @@
config SENSORS_W83627HF
tristate "Winbond W83627HF, W83627THF, W83637HF, W83697HF"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
+ select HWMON_VID
help
If you say yes here you get support for the Winbond W836X7 series
of sensor chips: the W83627HF, W83627THF, W83637HF, and the W83697HF
@@ -414,7 +397,6 @@
config SENSORS_W83627EHF
tristate "Winbond W83627EHF"
depends on HWMON && I2C && EXPERIMENTAL
- select I2C_SENSOR
select I2C_ISA
help
If you say yes here you get preliminary support for the hardware
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 187b89d..381f1bf 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -3,6 +3,7 @@
#
obj-$(CONFIG_HWMON) += hwmon.o
+obj-$(CONFIG_HWMON_VID) += hwmon-vid.o
# asb100, then w83781d go first, as they can override other drivers' addresses.
obj-$(CONFIG_SENSORS_ASB100) += asb100.o
diff --git a/drivers/hwmon/adm1025.c b/drivers/hwmon/adm1025.c
index 229fd0d..526b7ff 100644
--- a/drivers/hwmon/adm1025.c
+++ b/drivers/hwmon/adm1025.c
@@ -50,8 +50,8 @@
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/*
@@ -473,7 +473,7 @@
struct adm1025_data *data = i2c_get_clientdata(client);
int i;
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
/*
* Set high limits
diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c
index f32f819..6251581 100644
--- a/drivers/hwmon/adm1026.c
+++ b/drivers/hwmon/adm1026.c
@@ -28,9 +28,9 @@
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
-#include <linux/hwmon-sysfs.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/* Addresses to scan */
@@ -1552,7 +1552,7 @@
goto exitfree;
/* Set the VRM version */
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
/* Initialize the ADM1026 chip */
adm1026_init_client(new_client);
diff --git a/drivers/hwmon/adm9240.c b/drivers/hwmon/adm9240.c
index 0a742cb..bc7faef 100644
--- a/drivers/hwmon/adm9240.c
+++ b/drivers/hwmon/adm9240.c
@@ -45,8 +45,8 @@
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/* Addresses to scan */
@@ -657,7 +657,7 @@
u8 conf = adm9240_read_value(client, ADM9240_REG_CONFIG);
u8 mode = adm9240_read_value(client, ADM9240_REG_TEMP_CONF) & 3;
- data->vrm = i2c_which_vrm(); /* need this to report vid as mV */
+ data->vrm = vid_which_vrm(); /* need this to report vid as mV */
dev_info(&client->dev, "Using VRM: %d.%d\n", data->vrm / 10,
data->vrm % 10);
diff --git a/drivers/hwmon/asb100.c b/drivers/hwmon/asb100.c
index 66b0dbd..8e34855 100644
--- a/drivers/hwmon/asb100.c
+++ b/drivers/hwmon/asb100.c
@@ -39,8 +39,8 @@
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/jiffies.h>
@@ -973,7 +973,7 @@
vid = asb100_read_value(client, ASB100_REG_VID_FANDIV) & 0x0f;
vid |= (asb100_read_value(client, ASB100_REG_CHIPID) & 0x01) << 4;
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
vid = vid_from_reg(vid, data->vrm);
/* Start monitoring */
diff --git a/drivers/hwmon/atxp1.c b/drivers/hwmon/atxp1.c
index 5cf77e6..deb4d34 100644
--- a/drivers/hwmon/atxp1.c
+++ b/drivers/hwmon/atxp1.c
@@ -23,8 +23,8 @@
#include <linux/module.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
MODULE_LICENSE("GPL");
@@ -296,7 +296,7 @@
}
/* Get VRM */
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
if ((data->vrm != 90) && (data->vrm != 91)) {
dev_err(&new_client->dev, "Not supporting VRM %d.%d\n",
diff --git a/drivers/hwmon/gl520sm.c b/drivers/hwmon/gl520sm.c
index de6608a..12fd757 100644
--- a/drivers/hwmon/gl520sm.c
+++ b/drivers/hwmon/gl520sm.c
@@ -26,8 +26,8 @@
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/* Type of the extra sensor */
@@ -617,7 +617,7 @@
conf = oldconf = gl520_read_value(client, GL520_REG_CONF);
data->alarm_mask = 0xff;
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
if (extra_sensor_type == 1)
conf &= ~0x10;
diff --git a/drivers/hwmon/hwmon-vid.c b/drivers/hwmon/hwmon-vid.c
new file mode 100644
index 0000000..ce475c9
--- /dev/null
+++ b/drivers/hwmon/hwmon-vid.c
@@ -0,0 +1,103 @@
+/*
+ hwmon-vid.c - VID/VRM/VRD voltage conversions
+
+ Copyright (c) 2004 Rudolf Marek <r.marek@sh.cvut.cz>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/hwmon-vid.h>
+
+struct vrm_model {
+ u8 vendor;
+ u8 eff_family;
+ u8 eff_model;
+ int vrm_type;
+};
+
+#define ANY 0xFF
+
+#ifdef CONFIG_X86
+
+static struct vrm_model vrm_models[] = {
+ {X86_VENDOR_AMD, 0x6, ANY, 90}, /* Athlon Duron etc */
+ {X86_VENDOR_AMD, 0xF, ANY, 24}, /* Athlon 64, Opteron */
+ {X86_VENDOR_INTEL, 0x6, 0x9, 85}, /* 0.13um too */
+ {X86_VENDOR_INTEL, 0x6, 0xB, 85}, /* 0xB Tualatin */
+ {X86_VENDOR_INTEL, 0x6, ANY, 82}, /* any P6 */
+ {X86_VENDOR_INTEL, 0x7, ANY, 0}, /* Itanium */
+ {X86_VENDOR_INTEL, 0xF, 0x3, 100}, /* P4 Prescott */
+ {X86_VENDOR_INTEL, 0xF, ANY, 90}, /* P4 before Prescott */
+ {X86_VENDOR_INTEL, 0x10,ANY, 0}, /* Itanium 2 */
+ {X86_VENDOR_UNKNOWN, ANY, ANY, 0} /* stop here */
+ };
+
+static int find_vrm(u8 eff_family, u8 eff_model, u8 vendor)
+{
+ int i = 0;
+
+ while (vrm_models[i].vendor!=X86_VENDOR_UNKNOWN) {
+ if (vrm_models[i].vendor==vendor)
+ if ((vrm_models[i].eff_family==eff_family)&& \
+ ((vrm_models[i].eff_model==eff_model)|| \
+ (vrm_models[i].eff_model==ANY)))
+ return vrm_models[i].vrm_type;
+ i++;
+ }
+
+ return 0;
+}
+
+int vid_which_vrm(void)
+{
+ struct cpuinfo_x86 *c = cpu_data;
+ u32 eax;
+ u8 eff_family, eff_model;
+ int vrm_ret;
+
+ if (c->x86 < 6) return 0; /* any CPU with familly lower than 6
+ dont have VID and/or CPUID */
+ eax = cpuid_eax(1);
+ eff_family = ((eax & 0x00000F00)>>8);
+ eff_model = ((eax & 0x000000F0)>>4);
+ if (eff_family == 0xF) { /* use extended model & family */
+ eff_family += ((eax & 0x00F00000)>>20);
+ eff_model += ((eax & 0x000F0000)>>16)<<4;
+ }
+ vrm_ret = find_vrm(eff_family,eff_model,c->x86_vendor);
+ if (vrm_ret == 0)
+ printk(KERN_INFO "hwmon-vid: Unknown VRM version of your"
+ " x86 CPU\n");
+ return vrm_ret;
+}
+
+/* and now for something completely different for Non-x86 world*/
+#else
+int vid_which_vrm(void)
+{
+ printk(KERN_INFO "hwmon-vid: Unknown VRM version of your CPU\n");
+ return 0;
+}
+#endif
+
+EXPORT_SYMBOL(vid_which_vrm);
+
+MODULE_AUTHOR("Rudolf Marek <r.marek@sh.cvut.cz>");
+
+MODULE_DESCRIPTION("hwmon-vid driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c
index 8487766..53cc2b6 100644
--- a/drivers/hwmon/it87.c
+++ b/drivers/hwmon/it87.c
@@ -37,9 +37,9 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-isa.h>
-#include <linux/i2c-vid.h>
-#include <linux/hwmon-sysfs.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <asm/io.h>
@@ -919,7 +919,7 @@
}
if (data->type == it8712) {
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
device_create_file_vrm(new_client);
device_create_file_vid(new_client);
}
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index aeb4788..ab214df 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -28,8 +28,8 @@
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/* Addresses to scan */
@@ -1147,7 +1147,7 @@
goto ERROR1;
/* Set the VRM version */
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
/* Initialize the LM85 chip */
lm85_init_client(new_client);
diff --git a/drivers/hwmon/lm87.c b/drivers/hwmon/lm87.c
index d0d2464..dca996d 100644
--- a/drivers/hwmon/lm87.c
+++ b/drivers/hwmon/lm87.c
@@ -57,8 +57,8 @@
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
/*
@@ -694,7 +694,7 @@
u8 config;
data->channel = lm87_read_value(client, LM87_REG_CHANNEL_MODE);
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
config = lm87_read_value(client, LM87_REG_CONFIG);
if (!(config & 0x01)) {
diff --git a/drivers/hwmon/pc87360.c b/drivers/hwmon/pc87360.c
index c66ae4f..08fcb5ae 100644
--- a/drivers/hwmon/pc87360.c
+++ b/drivers/hwmon/pc87360.c
@@ -39,8 +39,8 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-isa.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <asm/io.h>
diff --git a/drivers/hwmon/w83627hf.c b/drivers/hwmon/w83627hf.c
index 2d2fcfb..02bd5c0 100644
--- a/drivers/hwmon/w83627hf.c
+++ b/drivers/hwmon/w83627hf.c
@@ -43,8 +43,8 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-isa.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <asm/io.h>
#include "lm75.h"
@@ -1316,7 +1316,7 @@
data->vrm = (data->vrm_ovt & 0x01) ? 90 : 82;
} else {
/* Convert VID to voltage based on default VRM */
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
}
tmp = w83627hf_read_value(client, W83781D_REG_SCFG1);
diff --git a/drivers/hwmon/w83781d.c b/drivers/hwmon/w83781d.c
index 4760798..4c43337 100644
--- a/drivers/hwmon/w83781d.c
+++ b/drivers/hwmon/w83781d.c
@@ -39,8 +39,8 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-isa.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <asm/io.h>
#include "lm75.h"
@@ -1478,7 +1478,7 @@
w83781d_write_value(client, W83781D_REG_BEEP_INTS2, 0);
}
- data->vrm = i2c_which_vrm();
+ data->vrm = vid_which_vrm();
if ((type != w83781d) && (type != as99127f)) {
tmp = w83781d_read_value(client, W83781D_REG_SCFG1);
diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c
index d6d8c0f..ba0c280 100644
--- a/drivers/hwmon/w83792d.c
+++ b/drivers/hwmon/w83792d.c
@@ -40,7 +40,6 @@
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
-#include <linux/i2c-vid.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>