diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index c8ab947..ed9b407 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -49,6 +49,9 @@
 #define DRV_NAME	"ahci"
 #define DRV_VERSION	"3.0"
 
+static int ahci_enable_alpm(struct ata_port *ap,
+		enum link_pm policy);
+static void ahci_disable_alpm(struct ata_port *ap);
 
 enum {
 	AHCI_PCI_BAR		= 5,
@@ -99,6 +102,7 @@
 	HOST_CAP_SSC		= (1 << 14), /* Slumber capable */
 	HOST_CAP_PMP		= (1 << 17), /* Port Multiplier support */
 	HOST_CAP_CLO		= (1 << 24), /* Command List Override support */
+	HOST_CAP_ALPM		= (1 << 26), /* Aggressive Link PM support */
 	HOST_CAP_SSS		= (1 << 27), /* Staggered Spin-up */
 	HOST_CAP_SNTF		= (1 << 29), /* SNotification register */
 	HOST_CAP_NCQ		= (1 << 30), /* Native Command Queueing */
@@ -155,6 +159,8 @@
 				  PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
 
 	/* PORT_CMD bits */
+	PORT_CMD_ASP		= (1 << 27), /* Aggressive Slumber/Partial */
+	PORT_CMD_ALPE		= (1 << 26), /* Aggressive Link PM enable */
 	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
 	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
 	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
@@ -178,13 +184,14 @@
 	AHCI_HFLAG_MV_PATA		= (1 << 4), /* PATA port */
 	AHCI_HFLAG_NO_MSI		= (1 << 5), /* no PCI MSI */
 	AHCI_HFLAG_NO_PMP		= (1 << 6), /* no PMP */
+	AHCI_HFLAG_NO_HOTPLUG		= (1 << 7), /* ignore PxSERR.DIAG.N */
 
 	/* ap->flags bits */
-	AHCI_FLAG_NO_HOTPLUG		= (1 << 24), /* ignore PxSERR.DIAG.N */
 
 	AHCI_FLAG_COMMON		= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
 					  ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
-					  ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
+					  ATA_FLAG_ACPI_SATA | ATA_FLAG_AN |
+					  ATA_FLAG_IPM,
 	AHCI_LFLAG_COMMON		= ATA_LFLAG_SKIP_D2H_BSY,
 };
 
@@ -254,6 +261,11 @@
 static int ahci_pci_device_resume(struct pci_dev *pdev);
 #endif
 
+static struct class_device_attribute *ahci_shost_attrs[] = {
+	&class_device_attr_link_power_management_policy,
+	NULL
+};
+
 static struct scsi_host_template ahci_sht = {
 	.module			= THIS_MODULE,
 	.name			= DRV_NAME,
@@ -271,6 +283,7 @@
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.shost_attrs		= ahci_shost_attrs,
 };
 
 static const struct ata_port_operations ahci_ops = {
@@ -302,6 +315,8 @@
 	.port_suspend		= ahci_port_suspend,
 	.port_resume		= ahci_port_resume,
 #endif
+	.enable_pm		= ahci_enable_alpm,
+	.disable_pm		= ahci_disable_alpm,
 
 	.port_start		= ahci_port_start,
 	.port_stop		= ahci_port_stop,
@@ -836,6 +851,130 @@
 	writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
 }
 
+static void ahci_disable_alpm(struct ata_port *ap)
+{
+	struct ahci_host_priv *hpriv = ap->host->private_data;
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 cmd;
+	struct ahci_port_priv *pp = ap->private_data;
+
+	/* IPM bits should be disabled by libata-core */
+	/* get the existing command bits */
+	cmd = readl(port_mmio + PORT_CMD);
+
+	/* disable ALPM and ASP */
+	cmd &= ~PORT_CMD_ASP;
+	cmd &= ~PORT_CMD_ALPE;
+
+	/* force the interface back to active */
+	cmd |= PORT_CMD_ICC_ACTIVE;
+
+	/* write out new cmd value */
+	writel(cmd, port_mmio + PORT_CMD);
+	cmd = readl(port_mmio + PORT_CMD);
+
+	/* wait 10ms to be sure we've come out of any low power state */
+	msleep(10);
+
+	/* clear out any PhyRdy stuff from interrupt status */
+	writel(PORT_IRQ_PHYRDY, port_mmio + PORT_IRQ_STAT);
+
+	/* go ahead and clean out PhyRdy Change from Serror too */
+	ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18)));
+
+	/*
+ 	 * Clear flag to indicate that we should ignore all PhyRdy
+ 	 * state changes
+ 	 */
+	hpriv->flags &= ~AHCI_HFLAG_NO_HOTPLUG;
+
+	/*
+ 	 * Enable interrupts on Phy Ready.
+ 	 */
+	pp->intr_mask |= PORT_IRQ_PHYRDY;
+	writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+	/*
+ 	 * don't change the link pm policy - we can be called
+ 	 * just to turn of link pm temporarily
+ 	 */
+}
+
+static int ahci_enable_alpm(struct ata_port *ap,
+	enum link_pm policy)
+{
+	struct ahci_host_priv *hpriv = ap->host->private_data;
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 cmd;
+	struct ahci_port_priv *pp = ap->private_data;
+	u32 asp;
+
+	/* Make sure the host is capable of link power management */
+	if (!(hpriv->cap & HOST_CAP_ALPM))
+		return -EINVAL;
+
+	switch (policy) {
+	case MAX_PERFORMANCE:
+	case NOT_AVAILABLE:
+		/*
+ 		 * if we came here with NOT_AVAILABLE,
+ 		 * it just means this is the first time we
+ 		 * have tried to enable - default to max performance,
+ 		 * and let the user go to lower power modes on request.
+ 		 */
+		ahci_disable_alpm(ap);
+		return 0;
+	case MIN_POWER:
+		/* configure HBA to enter SLUMBER */
+		asp = PORT_CMD_ASP;
+		break;
+	case MEDIUM_POWER:
+		/* configure HBA to enter PARTIAL */
+		asp = 0;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/*
+ 	 * Disable interrupts on Phy Ready. This keeps us from
+ 	 * getting woken up due to spurious phy ready interrupts
+	 * TBD - Hot plug should be done via polling now, is
+	 * that even supported?
+ 	 */
+	pp->intr_mask &= ~PORT_IRQ_PHYRDY;
+	writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+	/*
+ 	 * Set a flag to indicate that we should ignore all PhyRdy
+ 	 * state changes since these can happen now whenever we
+ 	 * change link state
+ 	 */
+	hpriv->flags |= AHCI_HFLAG_NO_HOTPLUG;
+
+	/* get the existing command bits */
+	cmd = readl(port_mmio + PORT_CMD);
+
+	/*
+ 	 * Set ASP based on Policy
+ 	 */
+	cmd |= asp;
+
+	/*
+ 	 * Setting this bit will instruct the HBA to aggressively
+ 	 * enter a lower power link state when it's appropriate and
+ 	 * based on the value set above for ASP
+ 	 */
+	cmd |= PORT_CMD_ALPE;
+
+	/* write out new cmd value */
+	writel(cmd, port_mmio + PORT_CMD);
+	cmd = readl(port_mmio + PORT_CMD);
+
+	/* IPM bits should be set by libata-core */
+	return 0;
+}
+
 #ifdef CONFIG_PM
 static void ahci_power_down(struct ata_port *ap)
 {
@@ -1504,6 +1643,17 @@
 	if (unlikely(resetting))
 		status &= ~PORT_IRQ_BAD_PMP;
 
+	/* If we are getting PhyRdy, this is
+ 	 * just a power state change, we should
+ 	 * clear out this, plus the PhyRdy/Comm
+ 	 * Wake bits from Serror
+ 	 */
+	if ((hpriv->flags & AHCI_HFLAG_NO_HOTPLUG) &&
+		(status & PORT_IRQ_PHYRDY)) {
+		status &= ~PORT_IRQ_PHYRDY;
+		ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18)));
+	}
+
 	if (unlikely(status & PORT_IRQ_ERROR)) {
 		ahci_error_intr(ap, status);
 		return;
@@ -2151,6 +2301,9 @@
 		ata_port_pbar_desc(ap, AHCI_PCI_BAR,
 				   0x100 + ap->port_no * 0x80, "port");
 
+		/* set initial link pm policy */
+		ap->pm_policy = NOT_AVAILABLE;
+
 		/* standard SATA port setup */
 		if (hpriv->port_map & (1 << i))
 			ap->ioaddr.cmd_addr = port_mmio;