smsc911x: allow mac address to be saved before device reset
Some platforms (for example pcm037) do not have an EEPROM fitted,
instead storing their mac address somewhere else. The bootloader
fetches this and configures the ethernet adapter before the kernel is
started.
This patch allows a platform to indicate to the driver via the
SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been
configured via such a mechanism, and should be saved before resetting
the chip.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
index 27d2d7c..6e175e5 100644
--- a/drivers/net/smsc911x.c
+++ b/drivers/net/smsc911x.c
@@ -1742,6 +1742,21 @@
#endif
};
+/* copies the current mac address from hardware to dev->dev_addr */
+static void __devinit smsc911x_read_mac_address(struct net_device *dev)
+{
+ struct smsc911x_data *pdata = netdev_priv(dev);
+ u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH);
+ u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL);
+
+ dev->dev_addr[0] = (u8)(mac_low32);
+ dev->dev_addr[1] = (u8)(mac_low32 >> 8);
+ dev->dev_addr[2] = (u8)(mac_low32 >> 16);
+ dev->dev_addr[3] = (u8)(mac_low32 >> 24);
+ dev->dev_addr[4] = (u8)(mac_high16);
+ dev->dev_addr[5] = (u8)(mac_high16 >> 8);
+}
+
/* Initializing private device structures, only called from probe */
static int __devinit smsc911x_init(struct net_device *dev)
{
@@ -1829,6 +1844,12 @@
SMSC_WARNING(PROBE,
"This driver is not intended for this chip revision");
+ /* workaround for platforms without an eeprom, where the mac address
+ * is stored elsewhere and set by the bootloader. This saves the
+ * mac address before resetting the device */
+ if (pdata->config.flags & SMSC911X_SAVE_MAC_ADDRESS)
+ smsc911x_read_mac_address(dev);
+
/* Reset the LAN911x */
if (smsc911x_soft_reset(pdata))
return -ENODEV;
@@ -2009,14 +2030,7 @@
} else {
/* Try reading mac address from device. if EEPROM is present
* it will already have been set */
- u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH);
- u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL);
- dev->dev_addr[0] = (u8)(mac_low32);
- dev->dev_addr[1] = (u8)(mac_low32 >> 8);
- dev->dev_addr[2] = (u8)(mac_low32 >> 16);
- dev->dev_addr[3] = (u8)(mac_low32 >> 24);
- dev->dev_addr[4] = (u8)(mac_high16);
- dev->dev_addr[5] = (u8)(mac_high16 >> 8);
+ smsc911x_read_mac_address(dev);
if (is_valid_ether_addr(dev->dev_addr)) {
/* eeprom values are valid so use them */