diff --git a/arch/arm/mach-mx3/mach-mx31ads.c b/arch/arm/mach-mx3/mach-mx31ads.c
new file mode 100644
index 0000000..1bcf226
--- /dev/null
+++ b/arch/arm/mach-mx3/mach-mx31ads.c
@@ -0,0 +1,551 @@
+/*
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
+ *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/serial_8250.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/memory.h>
+#include <asm/mach/map.h>
+#include <mach/common.h>
+#include <mach/board-mx31ads.h>
+#include <mach/imx-uart.h>
+#include <mach/iomux-mx3.h>
+
+#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
+#include <linux/mfd/wm8350/audio.h>
+#include <linux/mfd/wm8350/core.h>
+#include <linux/mfd/wm8350/pmic.h>
+#endif
+
+#include "devices.h"
+
+/*!
+ * @file mx31ads.c
+ *
+ * @brief This file contains the board-specific initialization routines.
+ *
+ * @ingroup System
+ */
+
+#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+/*!
+ * The serial port definition structure.
+ */
+static struct plat_serial8250_port serial_platform_data[] = {
+	{
+		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
+		.mapbase  = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTA),
+		.irq      = EXPIO_INT_XUART_INTA,
+		.uartclk  = 14745600,
+		.regshift = 0,
+		.iotype   = UPIO_MEM,
+		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
+	}, {
+		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
+		.mapbase  = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTB),
+		.irq      = EXPIO_INT_XUART_INTB,
+		.uartclk  = 14745600,
+		.regshift = 0,
+		.iotype   = UPIO_MEM,
+		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
+	},
+	{},
+};
+
+static struct platform_device serial_device = {
+	.name	= "serial8250",
+	.id	= 0,
+	.dev	= {
+		.platform_data = serial_platform_data,
+	},
+};
+
+static int __init mxc_init_extuart(void)
+{
+	return platform_device_register(&serial_device);
+}
+#else
+static inline int mxc_init_extuart(void)
+{
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
+static struct imxuart_platform_data uart_pdata = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+static unsigned int uart_pins[] = {
+	MX31_PIN_CTS1__CTS1,
+	MX31_PIN_RTS1__RTS1,
+	MX31_PIN_TXD1__TXD1,
+	MX31_PIN_RXD1__RXD1
+};
+
+static inline void mxc_init_imx_uart(void)
+{
+	mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
+	mxc_register_device(&mxc_uart_device0, &uart_pdata);
+}
+#else /* !SERIAL_IMX */
+static inline void mxc_init_imx_uart(void)
+{
+}
+#endif /* !SERIAL_IMX */
+
+static void mx31ads_expio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+	u32 imr_val;
+	u32 int_valid;
+	u32 expio_irq;
+
+	imr_val = __raw_readw(PBC_INTMASK_SET_REG);
+	int_valid = __raw_readw(PBC_INTSTATUS_REG) & imr_val;
+
+	expio_irq = MXC_EXP_IO_BASE;
+	for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
+		if ((int_valid & 1) == 0)
+			continue;
+
+		generic_handle_irq(expio_irq);
+	}
+}
+
+/*
+ * Disable an expio pin's interrupt by setting the bit in the imr.
+ * @param irq           an expio virtual irq number
+ */
+static void expio_mask_irq(u32 irq)
+{
+	u32 expio = MXC_IRQ_TO_EXPIO(irq);
+	/* mask the interrupt */
+	__raw_writew(1 << expio, PBC_INTMASK_CLEAR_REG);
+	__raw_readw(PBC_INTMASK_CLEAR_REG);
+}
+
+/*
+ * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
+ * @param irq           an expanded io virtual irq number
+ */
+static void expio_ack_irq(u32 irq)
+{
+	u32 expio = MXC_IRQ_TO_EXPIO(irq);
+	/* clear the interrupt status */
+	__raw_writew(1 << expio, PBC_INTSTATUS_REG);
+}
+
+/*
+ * Enable a expio pin's interrupt by clearing the bit in the imr.
+ * @param irq           a expio virtual irq number
+ */
+static void expio_unmask_irq(u32 irq)
+{
+	u32 expio = MXC_IRQ_TO_EXPIO(irq);
+	/* unmask the interrupt */
+	__raw_writew(1 << expio, PBC_INTMASK_SET_REG);
+}
+
+static struct irq_chip expio_irq_chip = {
+	.ack = expio_ack_irq,
+	.mask = expio_mask_irq,
+	.unmask = expio_unmask_irq,
+};
+
+static void __init mx31ads_init_expio(void)
+{
+	int i;
+
+	printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");
+
+	/*
+	 * Configure INT line as GPIO input
+	 */
+	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");
+
+	/* disable the interrupt and clear the status */
+	__raw_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
+	__raw_writew(0xFFFF, PBC_INTSTATUS_REG);
+	for (i = MXC_EXP_IO_BASE; i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
+	     i++) {
+		set_irq_chip(i, &expio_irq_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+	set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_HIGH);
+	set_irq_chained_handler(EXPIO_PARENT_INT, mx31ads_expio_irq_handler);
+}
+
+#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
+/* This section defines setup for the Wolfson Microelectronics
+ * 1133-EV1 PMU/audio board.  When other PMU boards are supported the
+ * regulator definitions may be shared with them, but for now they can
+ * only be used with this board so would generate warnings about
+ * unused statics and some of the configuration is specific to this
+ * module.
+ */
+
+/* CPU */
+static struct regulator_consumer_supply sw1a_consumers[] = {
+	{
+		.supply = "cpu_vcc",
+	}
+};
+
+static struct regulator_init_data sw1a_data = {
+	.constraints = {
+		.name = "SW1A",
+		.min_uV = 1275000,
+		.max_uV = 1600000,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_MODE,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+				    REGULATOR_MODE_FAST,
+		.state_mem = {
+			 .uV = 1400000,
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 1,
+		 },
+		.initial_state = PM_SUSPEND_MEM,
+		.always_on = 1,
+		.boot_on = 1,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(sw1a_consumers),
+	.consumer_supplies = sw1a_consumers,
+};
+
+/* System IO - High */
+static struct regulator_init_data viohi_data = {
+	.constraints = {
+		.name = "VIOHO",
+		.min_uV = 2800000,
+		.max_uV = 2800000,
+		.state_mem = {
+			 .uV = 2800000,
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 1,
+		 },
+		.initial_state = PM_SUSPEND_MEM,
+		.always_on = 1,
+		.boot_on = 1,
+	},
+};
+
+/* System IO - Low */
+static struct regulator_init_data violo_data = {
+	.constraints = {
+		.name = "VIOLO",
+		.min_uV = 1800000,
+		.max_uV = 1800000,
+		.state_mem = {
+			 .uV = 1800000,
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 1,
+		 },
+		.initial_state = PM_SUSPEND_MEM,
+		.always_on = 1,
+		.boot_on = 1,
+	},
+};
+
+/* DDR RAM */
+static struct regulator_init_data sw2a_data = {
+	.constraints = {
+		.name = "SW2A",
+		.min_uV = 1800000,
+		.max_uV = 1800000,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL,
+		.state_mem = {
+			 .uV = 1800000,
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 1,
+		 },
+		.state_disk = {
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 0,
+		 },
+		.always_on = 1,
+		.boot_on = 1,
+		.initial_state = PM_SUSPEND_MEM,
+	},
+};
+
+static struct regulator_init_data ldo1_data = {
+	.constraints = {
+		.name = "VCAM/VMMC1/VMMC2",
+		.min_uV = 2800000,
+		.max_uV = 2800000,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL,
+		.apply_uV = 1,
+	},
+};
+
+static struct regulator_consumer_supply ldo2_consumers[] = {
+	{
+		.supply = "AVDD",
+	},
+	{
+		.supply = "HPVDD",
+	},
+};
+
+/* CODEC and SIM */
+static struct regulator_init_data ldo2_data = {
+	.constraints = {
+		.name = "VESIM/VSIM/AVDD",
+		.min_uV = 3300000,
+		.max_uV = 3300000,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL,
+		.apply_uV = 1,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
+	.consumer_supplies = ldo2_consumers,
+};
+
+/* General */
+static struct regulator_init_data vdig_data = {
+	.constraints = {
+		.name = "VDIG",
+		.min_uV = 1500000,
+		.max_uV = 1500000,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL,
+		.apply_uV = 1,
+		.always_on = 1,
+		.boot_on = 1,
+	},
+};
+
+/* Tranceivers */
+static struct regulator_init_data ldo4_data = {
+	.constraints = {
+		.name = "VRF1/CVDD_2.775",
+		.min_uV = 2500000,
+		.max_uV = 2500000,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL,
+		.apply_uV = 1,
+		.always_on = 1,
+		.boot_on = 1,
+	},
+};
+
+static struct wm8350_led_platform_data wm8350_led_data = {
+	.name            = "wm8350:white",
+	.default_trigger = "heartbeat",
+	.max_uA          = 27899,
+};
+
+static struct wm8350_audio_platform_data imx32ads_wm8350_setup = {
+	.vmid_discharge_msecs = 1000,
+	.drain_msecs = 30,
+	.cap_discharge_msecs = 700,
+	.vmid_charge_msecs = 700,
+	.vmid_s_curve = WM8350_S_CURVE_SLOW,
+	.dis_out4 = WM8350_DISCHARGE_SLOW,
+	.dis_out3 = WM8350_DISCHARGE_SLOW,
+	.dis_out2 = WM8350_DISCHARGE_SLOW,
+	.dis_out1 = WM8350_DISCHARGE_SLOW,
+	.vroi_out4 = WM8350_TIE_OFF_500R,
+	.vroi_out3 = WM8350_TIE_OFF_500R,
+	.vroi_out2 = WM8350_TIE_OFF_500R,
+	.vroi_out1 = WM8350_TIE_OFF_500R,
+	.vroi_enable = 0,
+	.codec_current_on = WM8350_CODEC_ISEL_1_0,
+	.codec_current_standby = WM8350_CODEC_ISEL_0_5,
+	.codec_current_charge = WM8350_CODEC_ISEL_1_5,
+};
+
+static int mx31_wm8350_init(struct wm8350 *wm8350)
+{
+	int i;
+
+	wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN,
+			   WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW,
+			   WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_ON);
+
+	wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN,
+			   WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH,
+			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_ON);
+
+	wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN,
+			   WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH,
+			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_OFF);
+
+	wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN,
+			   WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH,
+			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_OFF);
+
+	wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT,
+			   WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH,
+			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_OFF);
+
+	wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT,
+			   WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
+			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_OFF);
+
+	wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT,
+			   WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
+			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
+			   WM8350_GPIO_DEBOUNCE_OFF);
+
+	/* Fix up for our own supplies. */
+	for (i = 0; i < ARRAY_SIZE(ldo2_consumers); i++)
+		ldo2_consumers[i].dev = wm8350->dev;
+
+	wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data);
+	wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data);
+	wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data);
+	wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data);
+	wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data);
+	wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data);
+	wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data);
+	wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data);
+
+	/* LEDs */
+	wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1,
+			     WM8350_DC5_ERRACT_SHUTDOWN_CONV);
+	wm8350_isink_set_flash(wm8350, WM8350_ISINK_A,
+			       WM8350_ISINK_FLASH_DISABLE,
+			       WM8350_ISINK_FLASH_TRIG_BIT,
+			       WM8350_ISINK_FLASH_DUR_32MS,
+			       WM8350_ISINK_FLASH_ON_INSTANT,
+			       WM8350_ISINK_FLASH_OFF_INSTANT,
+			       WM8350_ISINK_FLASH_MODE_EN);
+	wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5,
+			       WM8350_ISINK_MODE_BOOST,
+			       WM8350_ISINK_ILIM_NORMAL,
+			       WM8350_DC5_RMP_20V,
+			       WM8350_DC5_FBSRC_ISINKA);
+	wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A,
+			    &wm8350_led_data);
+
+	wm8350->codec.platform_data = &imx32ads_wm8350_setup;
+
+	regulator_has_full_constraints();
+
+	return 0;
+}
+
+static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
+	.init = mx31_wm8350_init,
+};
+#endif
+
+#if defined(CONFIG_I2C_IMX) || defined(CONFIG_I2C_IMX_MODULE)
+static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
+#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
+	{
+		I2C_BOARD_INFO("wm8350", 0x1a),
+		.platform_data = &mx31_wm8350_pdata,
+		.irq = IOMUX_TO_IRQ(MX31_PIN_GPIO1_3),
+	},
+#endif
+};
+
+static void mxc_init_i2c(void)
+{
+	i2c_register_board_info(1, mx31ads_i2c1_devices,
+				ARRAY_SIZE(mx31ads_i2c1_devices));
+
+	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
+	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));
+
+	mxc_register_device(&mxc_i2c_device1, NULL);
+}
+#else
+static void mxc_init_i2c(void)
+{
+}
+#endif
+
+/*!
+ * This structure defines static mappings for the i.MX31ADS board.
+ */
+static struct map_desc mx31ads_io_desc[] __initdata = {
+	{
+		.virtual	= MX31_CS4_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(MX31_CS4_BASE_ADDR),
+		.length		= MX31_CS4_SIZE / 2,
+		.type		= MT_DEVICE
+	},
+};
+
+/*!
+ * Set up static virtual mappings.
+ */
+static void __init mx31ads_map_io(void)
+{
+	mx31_map_io();
+	iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
+}
+
+static void __init mx31ads_init_irq(void)
+{
+	mx31_init_irq();
+	mx31ads_init_expio();
+}
+
+/*!
+ * Board specific initialization.
+ */
+static void __init mxc_board_init(void)
+{
+	mxc_init_extuart();
+	mxc_init_imx_uart();
+	mxc_init_i2c();
+}
+
+static void __init mx31ads_timer_init(void)
+{
+	mx31_clocks_init(26000000);
+}
+
+static struct sys_timer mx31ads_timer = {
+	.init	= mx31ads_timer_init,
+};
+
+/*
+ * The following uses standard kernel macros defined in arch.h in order to
+ * initialize __mach_desc_MX31ADS data structure.
+ */
+MACHINE_START(MX31ADS, "Freescale MX31ADS")
+	/* Maintainer: Freescale Semiconductor, Inc. */
+	.phys_io	= MX31_AIPS1_BASE_ADDR,
+	.io_pg_offst	= (MX31_AIPS1_BASE_ADDR_VIRT >> 18) & 0xfffc,
+	.boot_params    = PHYS_OFFSET + 0x100,
+	.map_io         = mx31ads_map_io,
+	.init_irq       = mx31ads_init_irq,
+	.init_machine   = mxc_board_init,
+	.timer          = &mx31ads_timer,
+MACHINE_END