document: devicetree: bind pinconf with pin single
Add comments with pinconf & gpio range in the document of
pinctrl-single.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
index 2c81e45..fa1746b 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -1,7 +1,9 @@
One-register-per-pin type device tree based pinctrl driver
Required properties:
-- compatible : "pinctrl-single"
+- compatible : "pinctrl-single" or "pinconf-single".
+ "pinctrl-single" means that pinconf isn't supported.
+ "pinconf-single" means that generic pinconf is supported.
- reg : offset and length of the register set for the mux registers
@@ -14,9 +16,61 @@
- pinctrl-single,function-off : function off mode for disabled state if
available and same for all registers; if not specified, disabling of
pin functions is ignored
+
- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
more than one pin
+- pinctrl-single,drive-strength : array of value that are used to configure
+ drive strength in the pinmux register. They're value of drive strength
+ current and drive strength mask.
+
+ /* drive strength current, mask */
+ pinctrl-single,power-source = <0x30 0xf0>;
+
+- pinctrl-single,bias-pullup : array of value that are used to configure the
+ input bias pullup in the pinmux register.
+
+ /* input, enabled pullup bits, disabled pullup bits, mask */
+ pinctrl-single,bias-pullup = <0 1 0 1>;
+
+- pinctrl-single,bias-pulldown : array of value that are used to configure the
+ input bias pulldown in the pinmux register.
+
+ /* input, enabled pulldown bits, disabled pulldown bits, mask */
+ pinctrl-single,bias-pulldown = <2 2 0 2>;
+
+ * Two bits to control input bias pullup and pulldown: User should use
+ pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
+ pullup, and the other one bit means pulldown.
+ * Three bits to control input bias enable, pullup and pulldown. User should
+ use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
+ enable bit should be included in pullup or pulldown bits.
+ * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
+ pinctrl-single,bias-disable. Because pinctrl single driver could implement
+ it by calling pulldown, pullup disabled.
+
+- pinctrl-single,input-schmitt : array of value that are used to configure
+ input schmitt in the pinmux register. In some silicons, there're two input
+ schmitt value (rising-edge & falling-edge) in the pinmux register.
+
+ /* input schmitt value, mask */
+ pinctrl-single,input-schmitt = <0x30 0x70>;
+
+- pinctrl-single,input-schmitt-enable : array of value that are used to
+ configure input schmitt enable or disable in the pinmux register.
+
+ /* input, enable bits, disable bits, mask */
+ pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
+
+- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
+ range. They're value of subnode phandle, pin base in pinctrl device, pin
+ number in this range, GPIO function value of this GPIO range.
+ The number of parameters is depend on #pinctrl-single,gpio-range-cells
+ property.
+
+ /* pin base, nr pins & gpio function */
+ pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
+
This driver assumes that there is only one register for each pin (unless the
pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
specified in the pinctrl-bindings.txt document in this directory.
@@ -42,6 +96,20 @@
device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
be used when applying this change to the register.
+
+Optional sub-node: In case some pins could be configured as GPIO in the pinmux
+register, those pins could be defined as a GPIO range. This sub-node is required
+by pinctrl-single,gpio-range property.
+
+Required properties in sub-node:
+- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
+ pinctrl-single,gpio-range property.
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+
+
Example:
/* SoC common file */
@@ -76,6 +144,29 @@
pinctrl-single,function-mask = <0x5F>;
};
+/* third controller instance for pins in gpio domain */
+pmx_gpio: pinmux@d401e000 {
+ compatible = "pinconf-single";
+ reg = <0xd401e000 0x0330>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <7>;
+
+ /* sparse GPIO range could be supported */
+ pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+ &range 12 1 0 &range 13 29 1
+ &range 43 1 0 &range 44 49 1
+ &range 94 1 1 &range 96 2 1>;
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+};
+
+
/* board specific .dts file */
&pmx_core {
@@ -96,6 +187,15 @@
>;
};
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x208 0 /* UART0_RXD (IOCFG138) */
+ 0x20c 0 /* UART0_TXD (IOCFG139) */
+ >;
+ pinctrl-single,bias-pulldown = <0 2 2>;
+ pinctrl-single,bias-pullup = <0 1 1>;
+ };
+
/* map uart2 pins */
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
@@ -122,6 +222,11 @@
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;