| /* |
| * OMAP MPUSS low power code |
| * |
| * Copyright (C) 2011 Texas Instruments, Inc. |
| * Santosh Shilimkar <santosh.shilimkar@ti.com> |
| * |
| * OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU |
| * Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller, |
| * CPU0 and CPU1 LPRM modules. |
| * CPU0, CPU1 and MPUSS each have there own power domain and |
| * hence multiple low power combinations of MPUSS are possible. |
| * |
| * The CPU0 and CPU1 can't support Closed switch Retention (CSWR) |
| * because the mode is not supported by hw constraints of dormant |
| * mode. While waking up from the dormant mode, a reset signal |
| * to the Cortex-A9 processor must be asserted by the external |
| * power controller. |
| * |
| * With architectural inputs and hardware recommendations, only |
| * below modes are supported from power gain vs latency point of view. |
| * |
| * CPU0 CPU1 MPUSS |
| * ---------------------------------------------- |
| * ON ON ON |
| * ON(Inactive) OFF ON(Inactive) |
| * OFF OFF CSWR |
| * OFF OFF OSWR |
| * OFF OFF OFF(Device OFF *TBD) |
| * ---------------------------------------------- |
| * |
| * Note: CPU0 is the master core and it is the last CPU to go down |
| * and first to wake-up when MPUSS low power states are excercised |
| * |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/io.h> |
| #include <linux/errno.h> |
| #include <linux/linkage.h> |
| #include <linux/smp.h> |
| |
| #include <asm/cacheflush.h> |
| #include <asm/tlbflush.h> |
| #include <asm/smp_scu.h> |
| #include <asm/pgalloc.h> |
| #include <asm/suspend.h> |
| #include <asm/hardware/cache-l2x0.h> |
| |
| #include "soc.h" |
| #include "common.h" |
| #include "omap44xx.h" |
| #include "omap4-sar-layout.h" |
| #include "pm.h" |
| #include "prcm_mpu44xx.h" |
| #include "prcm_mpu54xx.h" |
| #include "prminst44xx.h" |
| #include "prcm44xx.h" |
| #include "prm44xx.h" |
| #include "prm-regbits-44xx.h" |
| |
| #ifdef CONFIG_SMP |
| |
| struct omap4_cpu_pm_info { |
| struct powerdomain *pwrdm; |
| void __iomem *scu_sar_addr; |
| void __iomem *wkup_sar_addr; |
| void __iomem *l2x0_sar_addr; |
| void (*secondary_startup)(void); |
| }; |
| |
| /** |
| * struct cpu_pm_ops - CPU pm operations |
| * @finish_suspend: CPU suspend finisher function pointer |
| * @resume: CPU resume function pointer |
| * @scu_prepare: CPU Snoop Control program function pointer |
| * |
| * Structure holds functions pointer for CPU low power operations like |
| * suspend, resume and scu programming. |
| */ |
| struct cpu_pm_ops { |
| int (*finish_suspend)(unsigned long cpu_state); |
| void (*resume)(void); |
| void (*scu_prepare)(unsigned int cpu_id, unsigned int cpu_state); |
| }; |
| |
| static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info); |
| static struct powerdomain *mpuss_pd; |
| static void __iomem *sar_base; |
| static u32 cpu_context_offset; |
| |
| static int default_finish_suspend(unsigned long cpu_state) |
| { |
| omap_do_wfi(); |
| return 0; |
| } |
| |
| static void dummy_cpu_resume(void) |
| {} |
| |
| static void dummy_scu_prepare(unsigned int cpu_id, unsigned int cpu_state) |
| {} |
| |
| struct cpu_pm_ops omap_pm_ops = { |
| .finish_suspend = default_finish_suspend, |
| .resume = dummy_cpu_resume, |
| .scu_prepare = dummy_scu_prepare, |
| }; |
| |
| /* |
| * Program the wakeup routine address for the CPU0 and CPU1 |
| * used for OFF or DORMANT wakeup. |
| */ |
| static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr) |
| { |
| struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id); |
| |
| if (pm_info->wkup_sar_addr) |
| writel_relaxed(addr, pm_info->wkup_sar_addr); |
| } |
| |
| /* |
| * Store the SCU power status value to scratchpad memory |
| */ |
| static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state) |
| { |
| struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id); |
| u32 scu_pwr_st; |
| |
| switch (cpu_state) { |
| case PWRDM_POWER_RET: |
| scu_pwr_st = SCU_PM_DORMANT; |
| break; |
| case PWRDM_POWER_OFF: |
| scu_pwr_st = SCU_PM_POWEROFF; |
| break; |
| case PWRDM_POWER_ON: |
| case PWRDM_POWER_INACTIVE: |
| default: |
| scu_pwr_st = SCU_PM_NORMAL; |
| break; |
| } |
| |
| if (pm_info->scu_sar_addr) |
| writel_relaxed(scu_pwr_st, pm_info->scu_sar_addr); |
| } |
| |
| /* Helper functions for MPUSS OSWR */ |
| static inline void mpuss_clear_prev_logic_pwrst(void) |
| { |
| u32 reg; |
| |
| reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION, |
| OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET); |
| omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION, |
| OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET); |
| } |
| |
| static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id) |
| { |
| u32 reg; |
| |
| if (cpu_id) { |
| reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST, |
| cpu_context_offset); |
| omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST, |
| cpu_context_offset); |
| } else { |
| reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST, |
| cpu_context_offset); |
| omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST, |
| cpu_context_offset); |
| } |
| } |
| |
| /* |
| * Store the CPU cluster state for L2X0 low power operations. |
| */ |
| static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state) |
| { |
| struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id); |
| |
| if (pm_info->l2x0_sar_addr) |
| writel_relaxed(save_state, pm_info->l2x0_sar_addr); |
| } |
| |
| /* |
| * Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to |
| * in every restore MPUSS OFF path. |
| */ |
| #ifdef CONFIG_CACHE_L2X0 |
| static void __init save_l2x0_context(void) |
| { |
| void __iomem *l2x0_base = omap4_get_l2cache_base(); |
| |
| if (l2x0_base && sar_base) { |
| writel_relaxed(l2x0_saved_regs.aux_ctrl, |
| sar_base + L2X0_AUXCTRL_OFFSET); |
| writel_relaxed(l2x0_saved_regs.prefetch_ctrl, |
| sar_base + L2X0_PREFETCH_CTRL_OFFSET); |
| } |
| } |
| #else |
| static void __init save_l2x0_context(void) |
| {} |
| #endif |
| |
| /** |
| * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function |
| * The purpose of this function is to manage low power programming |
| * of OMAP4 MPUSS subsystem |
| * @cpu : CPU ID |
| * @power_state: Low power state. |
| * |
| * MPUSS states for the context save: |
| * save_state = |
| * 0 - Nothing lost and no need to save: MPUSS INACTIVE |
| * 1 - CPUx L1 and logic lost: MPUSS CSWR |
| * 2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR |
| * 3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF |
| */ |
| int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state) |
| { |
| struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu); |
| unsigned int save_state = 0; |
| unsigned int wakeup_cpu; |
| |
| if (omap_rev() == OMAP4430_REV_ES1_0) |
| return -ENXIO; |
| |
| switch (power_state) { |
| case PWRDM_POWER_ON: |
| case PWRDM_POWER_INACTIVE: |
| save_state = 0; |
| break; |
| case PWRDM_POWER_OFF: |
| save_state = 1; |
| break; |
| case PWRDM_POWER_RET: |
| default: |
| /* |
| * CPUx CSWR is invalid hardware state. Also CPUx OSWR |
| * doesn't make much scense, since logic is lost and $L1 |
| * needs to be cleaned because of coherency. This makes |
| * CPUx OSWR equivalent to CPUX OFF and hence not supported |
| */ |
| WARN_ON(1); |
| return -ENXIO; |
| } |
| |
| pwrdm_pre_transition(NULL); |
| |
| /* |
| * Check MPUSS next state and save interrupt controller if needed. |
| * In MPUSS OSWR or device OFF, interrupt controller contest is lost. |
| */ |
| mpuss_clear_prev_logic_pwrst(); |
| if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) && |
| (pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF)) |
| save_state = 2; |
| |
| cpu_clear_prev_logic_pwrst(cpu); |
| pwrdm_set_next_pwrst(pm_info->pwrdm, power_state); |
| set_cpu_wakeup_addr(cpu, virt_to_phys(omap_pm_ops.resume)); |
| omap_pm_ops.scu_prepare(cpu, power_state); |
| l2x0_pwrst_prepare(cpu, save_state); |
| |
| /* |
| * Call low level function with targeted low power state. |
| */ |
| if (save_state) |
| cpu_suspend(save_state, omap_pm_ops.finish_suspend); |
| else |
| omap_pm_ops.finish_suspend(save_state); |
| |
| if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) && cpu) |
| gic_dist_enable(); |
| |
| /* |
| * Restore the CPUx power state to ON otherwise CPUx |
| * power domain can transitions to programmed low power |
| * state while doing WFI outside the low powe code. On |
| * secure devices, CPUx does WFI which can result in |
| * domain transition |
| */ |
| wakeup_cpu = smp_processor_id(); |
| pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON); |
| |
| pwrdm_post_transition(NULL); |
| |
| return 0; |
| } |
| |
| /** |
| * omap4_hotplug_cpu: OMAP4 CPU hotplug entry |
| * @cpu : CPU ID |
| * @power_state: CPU low power state. |
| */ |
| int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state) |
| { |
| struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu); |
| unsigned int cpu_state = 0; |
| |
| if (omap_rev() == OMAP4430_REV_ES1_0) |
| return -ENXIO; |
| |
| if (power_state == PWRDM_POWER_OFF) |
| cpu_state = 1; |
| |
| pwrdm_clear_all_prev_pwrst(pm_info->pwrdm); |
| pwrdm_set_next_pwrst(pm_info->pwrdm, power_state); |
| set_cpu_wakeup_addr(cpu, virt_to_phys(pm_info->secondary_startup)); |
| omap_pm_ops.scu_prepare(cpu, power_state); |
| |
| /* |
| * CPU never retuns back if targeted power state is OFF mode. |
| * CPU ONLINE follows normal CPU ONLINE ptah via |
| * omap4_secondary_startup(). |
| */ |
| omap_pm_ops.finish_suspend(cpu_state); |
| |
| pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON); |
| return 0; |
| } |
| |
| |
| /* |
| * Enable Mercury Fast HG retention mode by default. |
| */ |
| static void enable_mercury_retention_mode(void) |
| { |
| u32 reg; |
| |
| reg = omap4_prcm_mpu_read_inst_reg(OMAP54XX_PRCM_MPU_DEVICE_INST, |
| OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET); |
| /* Enable HG_EN, HG_RAMPUP = fast mode */ |
| reg |= BIT(24) | BIT(25); |
| omap4_prcm_mpu_write_inst_reg(reg, OMAP54XX_PRCM_MPU_DEVICE_INST, |
| OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET); |
| } |
| |
| /* |
| * Initialise OMAP4 MPUSS |
| */ |
| int __init omap4_mpuss_init(void) |
| { |
| struct omap4_cpu_pm_info *pm_info; |
| |
| if (omap_rev() == OMAP4430_REV_ES1_0) { |
| WARN(1, "Power Management not supported on OMAP4430 ES1.0\n"); |
| return -ENODEV; |
| } |
| |
| if (cpu_is_omap44xx()) |
| sar_base = omap4_get_sar_ram_base(); |
| |
| /* Initilaise per CPU PM information */ |
| pm_info = &per_cpu(omap4_pm_info, 0x0); |
| if (sar_base) { |
| pm_info->scu_sar_addr = sar_base + SCU_OFFSET0; |
| pm_info->wkup_sar_addr = sar_base + |
| CPU0_WAKEUP_NS_PA_ADDR_OFFSET; |
| pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0; |
| } |
| pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm"); |
| if (!pm_info->pwrdm) { |
| pr_err("Lookup failed for CPU0 pwrdm\n"); |
| return -ENODEV; |
| } |
| |
| /* Clear CPU previous power domain state */ |
| pwrdm_clear_all_prev_pwrst(pm_info->pwrdm); |
| cpu_clear_prev_logic_pwrst(0); |
| |
| /* Initialise CPU0 power domain state to ON */ |
| pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON); |
| |
| pm_info = &per_cpu(omap4_pm_info, 0x1); |
| if (sar_base) { |
| pm_info->scu_sar_addr = sar_base + SCU_OFFSET1; |
| pm_info->wkup_sar_addr = sar_base + |
| CPU1_WAKEUP_NS_PA_ADDR_OFFSET; |
| pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1; |
| } |
| if (cpu_is_omap446x()) |
| pm_info->secondary_startup = omap4460_secondary_startup; |
| else |
| pm_info->secondary_startup = omap4_secondary_startup; |
| |
| pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm"); |
| if (!pm_info->pwrdm) { |
| pr_err("Lookup failed for CPU1 pwrdm\n"); |
| return -ENODEV; |
| } |
| |
| /* Clear CPU previous power domain state */ |
| pwrdm_clear_all_prev_pwrst(pm_info->pwrdm); |
| cpu_clear_prev_logic_pwrst(1); |
| |
| /* Initialise CPU1 power domain state to ON */ |
| pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON); |
| |
| mpuss_pd = pwrdm_lookup("mpu_pwrdm"); |
| if (!mpuss_pd) { |
| pr_err("Failed to lookup MPUSS power domain\n"); |
| return -ENODEV; |
| } |
| pwrdm_clear_all_prev_pwrst(mpuss_pd); |
| mpuss_clear_prev_logic_pwrst(); |
| |
| if (sar_base) { |
| /* Save device type on scratchpad for low level code to use */ |
| writel_relaxed((omap_type() != OMAP2_DEVICE_TYPE_GP) ? 1 : 0, |
| sar_base + OMAP_TYPE_OFFSET); |
| save_l2x0_context(); |
| } |
| |
| if (cpu_is_omap44xx()) { |
| omap_pm_ops.finish_suspend = omap4_finish_suspend; |
| omap_pm_ops.resume = omap4_cpu_resume; |
| omap_pm_ops.scu_prepare = scu_pwrst_prepare; |
| cpu_context_offset = OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET; |
| } else if (soc_is_omap54xx() || soc_is_dra7xx()) { |
| cpu_context_offset = OMAP54XX_RM_CPU0_CPU0_CONTEXT_OFFSET; |
| enable_mercury_retention_mode(); |
| } |
| |
| return 0; |
| } |
| |
| #endif |