Gitiles
Code Review Sign In
gerrit-public.fairphone.software / kernel / msm-4.9 / 334c6f0218f0e2bf2fa478c20993ca997e11c922 / . / drivers / usb / host / xhci-hub.c
blob: 643e087babcadee60169665e54951cc6f7e4a6e5 [file] [log] [blame]
/*
* xHCI host controller driver
*
* Copyright (C) 2008 Intel Corp.
*
* Author: Sarah Sharp
* Some code borrowed from the Linux EHCI driver.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/gfp.h>
#include <linux/slab.h>
#include <asm/unaligned.h>
#include <linux/usb/phy.h>
#include "xhci.h"
#include "xhci-trace.h"
#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
#define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
PORT_RC | PORT_PLC | PORT_PE)
/* USB 3 BOS descriptor and a capability descriptors, combined.
* Fields will be adjusted and added later in xhci_create_usb3_bos_desc()
*/
static u8 usb_bos_descriptor [] = {
USB_DT_BOS_SIZE, /* __u8 bLength, 5 bytes */
USB_DT_BOS, /* __u8 bDescriptorType */
0x0F, 0x00, /* __le16 wTotalLength, 15 bytes */
0x1, /* __u8 bNumDeviceCaps */
/* First device capability, SuperSpeed */
USB_DT_USB_SS_CAP_SIZE, /* __u8 bLength, 10 bytes */
USB_DT_DEVICE_CAPABILITY, /* Device Capability */
USB_SS_CAP_TYPE, /* bDevCapabilityType, SUPERSPEED_USB */
0x00, /* bmAttributes, LTM off by default */
USB_5GBPS_OPERATION, 0x00, /* wSpeedsSupported, 5Gbps only */
0x03, /* bFunctionalitySupport,
USB 3.0 speed only */
0x00, /* bU1DevExitLat, set later. */
0x00, 0x00, /* __le16 bU2DevExitLat, set later. */
/* Second device capability, SuperSpeedPlus */
0x1c, /* bLength 28, will be adjusted later */
USB_DT_DEVICE_CAPABILITY, /* Device Capability */
USB_SSP_CAP_TYPE, /* bDevCapabilityType SUPERSPEED_PLUS */
0x00, /* bReserved 0 */
0x23, 0x00, 0x00, 0x00, /* bmAttributes, SSAC=3 SSIC=1 */
0x01, 0x00, /* wFunctionalitySupport */
0x00, 0x00, /* wReserved 0 */
/* Default Sublink Speed Attributes, overwrite if custom PSI exists */
0x34, 0x00, 0x05, 0x00, /* 5Gbps, symmetric, rx, ID = 4 */
0xb4, 0x00, 0x05, 0x00, /* 5Gbps, symmetric, tx, ID = 4 */
0x35, 0x40, 0x0a, 0x00, /* 10Gbps, SSP, symmetric, rx, ID = 5 */
0xb5, 0x40, 0x0a, 0x00, /* 10Gbps, SSP, symmetric, tx, ID = 5 */
};
static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
u16 wLength)
{
int i, ssa_count;
u32 temp;
u16 desc_size, ssp_cap_size, ssa_size = 0;
bool usb3_1 = false;
desc_size = USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
ssp_cap_size = sizeof(usb_bos_descriptor) - desc_size;
/* does xhci support USB 3.1 Enhanced SuperSpeed */
if (xhci->usb3_rhub.min_rev >= 0x01) {
/* does xhci provide a PSI table for SSA speed attributes? */
if (xhci->usb3_rhub.psi_count) {
/* two SSA entries for each unique PSI ID, RX and TX */
ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
ssa_size = ssa_count * sizeof(u32);
ssp_cap_size -= 16; /* skip copying the default SSA */
}
desc_size += ssp_cap_size;
usb3_1 = true;
}
memcpy(buf, &usb_bos_descriptor, min(desc_size, wLength));
if (usb3_1) {
/* modify bos descriptor bNumDeviceCaps and wTotalLength */
buf[4] += 1;
put_unaligned_le16(desc_size + ssa_size, &buf[2]);
}
if (wLength < USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE)
return wLength;
/* Indicate whether the host has LTM support. */
temp = readl(&xhci->cap_regs->hcc_params);
if (HCC_LTC(temp))
buf[8] |= USB_LTM_SUPPORT;
/* Set the U1 and U2 exit latencies. */
if ((xhci->quirks & XHCI_LPM_SUPPORT)) {
temp = readl(&xhci->cap_regs->hcs_params3);
buf[12] = HCS_U1_LATENCY(temp);
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
}
/* If PSI table exists, add the custom speed attributes from it */
if (usb3_1 && xhci->usb3_rhub.psi_count) {
u32 ssp_cap_base, bm_attrib, psi, psi_mant, psi_exp;
int offset;
ssp_cap_base = USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
if (wLength < desc_size)
return wLength;
buf[ssp_cap_base] = ssp_cap_size + ssa_size;
/* attribute count SSAC bits 4:0 and ID count SSIC bits 8:5 */
bm_attrib = (ssa_count - 1) & 0x1f;
bm_attrib |= (xhci->usb3_rhub.psi_uid_count - 1) << 5;
put_unaligned_le32(bm_attrib, &buf[ssp_cap_base + 4]);
if (wLength < desc_size + ssa_size)
return wLength;
/*
* Create the Sublink Speed Attributes (SSA) array.
* The xhci PSI field and USB 3.1 SSA fields are very similar,
* but link type bits 7:6 differ for values 01b and 10b.
* xhci has also only one PSI entry for a symmetric link when
* USB 3.1 requires two SSA entries (RX and TX) for every link
*/
offset = desc_size;
for (i = 0; i < xhci->usb3_rhub.psi_count; i++) {
psi = xhci->usb3_rhub.psi[i];
psi &= ~USB_SSP_SUBLINK_SPEED_RSVD;
psi_exp = XHCI_EXT_PORT_PSIE(psi);
psi_mant = XHCI_EXT_PORT_PSIM(psi);
/* Shift to Gbps and set SSP Link BIT(14) if 10Gpbs */
for (; psi_exp < 3; psi_exp++)
psi_mant /= 1000;
if (psi_mant >= 10)
psi |= BIT(14);
if ((psi & PLT_MASK) == PLT_SYM) {
/* Symmetric, create SSA RX and TX from one PSI entry */
put_unaligned_le32(psi, &buf[offset]);
psi |= 1 << 7; /* turn entry to TX */
offset += 4;
if (offset >= desc_size + ssa_size)
return desc_size + ssa_size;
} else if ((psi & PLT_MASK) == PLT_ASYM_RX) {
/* Asymetric RX, flip bits 7:6 for SSA */
psi ^= PLT_MASK;
}
put_unaligned_le32(psi, &buf[offset]);
offset += 4;
if (offset >= desc_size + ssa_size)
return desc_size + ssa_size;
}
}
/* ssa_size is 0 for other than usb 3.1 hosts */
return desc_size + ssa_size;
}
static void xhci_common_hub_descriptor(struct xhci_hcd *xhci,
struct usb_hub_descriptor *desc, int ports)
{
u16 temp;
desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.9 says 20ms max */
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ports;
temp = 0;
/* Bits 1:0 - support per-port power switching, or power always on */
if (HCC_PPC(xhci->hcc_params))
temp |= HUB_CHAR_INDV_PORT_LPSM;
else
temp |= HUB_CHAR_NO_LPSM;
/* Bit 2 - root hubs are not part of a compound device */
/* Bits 4:3 - individual port over current protection */
temp |= HUB_CHAR_INDV_PORT_OCPM;
/* Bits 6:5 - no TTs in root ports */
/* Bit 7 - no port indicators */
desc->wHubCharacteristics = cpu_to_le16(temp);
}
/* Fill in the USB 2.0 roothub descriptor */
static void xhci_usb2_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
struct usb_hub_descriptor *desc)
{
int ports;
u16 temp;
__u8 port_removable[(USB_MAXCHILDREN + 1 + 7) / 8];
u32 portsc;
unsigned int i;
ports = xhci->num_usb2_ports;
xhci_common_hub_descriptor(xhci, desc, ports);
desc->bDescriptorType = USB_DT_HUB;
temp = 1 + (ports / 8);
desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp;
/* The Device Removable bits are reported on a byte granularity.
* If the port doesn't exist within that byte, the bit is set to 0.
*/
memset(port_removable, 0, sizeof(port_removable));
for (i = 0; i < ports; i++) {
portsc = readl(xhci->usb2_ports[i]);
/* If a device is removable, PORTSC reports a 0, same as in the
* hub descriptor DeviceRemovable bits.
*/
if (portsc & PORT_DEV_REMOVE)
/* This math is hairy because bit 0 of DeviceRemovable
* is reserved, and bit 1 is for port 1, etc.
*/
port_removable[(i + 1) / 8] |= 1 << ((i + 1) % 8);
}
/* ch11.h defines a hub descriptor that has room for USB_MAXCHILDREN
* ports on it. The USB 2.0 specification says that there are two
* variable length fields at the end of the hub descriptor:
* DeviceRemovable and PortPwrCtrlMask. But since we can have less than
* USB_MAXCHILDREN ports, we may need to use the DeviceRemovable array
* to set PortPwrCtrlMask bits. PortPwrCtrlMask must always be set to
* 0xFF, so we initialize the both arrays (DeviceRemovable and
* PortPwrCtrlMask) to 0xFF. Then we set the DeviceRemovable for each
* set of ports that actually exist.
*/
memset(desc->u.hs.DeviceRemovable, 0xff,
sizeof(desc->u.hs.DeviceRemovable));
memset(desc->u.hs.PortPwrCtrlMask, 0xff,
sizeof(desc->u.hs.PortPwrCtrlMask));
for (i = 0; i < (ports + 1 + 7) / 8; i++)
memset(&desc->u.hs.DeviceRemovable[i], port_removable[i],
sizeof(__u8));
}
/* Fill in the USB 3.0 roothub descriptor */
static void xhci_usb3_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
struct usb_hub_descriptor *desc)
{
int ports;
u16 port_removable;
u32 portsc;
unsigned int i;
ports = xhci->num_usb3_ports;
xhci_common_hub_descriptor(xhci, desc, ports);
desc->bDescriptorType = USB_DT_SS_HUB;
desc->bDescLength = USB_DT_SS_HUB_SIZE;
/* header decode latency should be zero for roothubs,
* see section 4.23.5.2.
*/
desc->u.ss.bHubHdrDecLat = 0;
desc->u.ss.wHubDelay = 0;
port_removable = 0;
/* bit 0 is reserved, bit 1 is for port 1, etc. */
for (i = 0; i < ports; i++) {
portsc = readl(xhci->usb3_ports[i]);
if (portsc & PORT_DEV_REMOVE)
port_removable |= 1 << (i + 1);
}
desc->u.ss.DeviceRemovable = cpu_to_le16(port_removable);
}
static void xhci_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci,
struct usb_hub_descriptor *desc)
{
if (hcd->speed >= HCD_USB3)
xhci_usb3_hub_descriptor(hcd, xhci, desc);
else
xhci_usb2_hub_descriptor(hcd, xhci, desc);
}
static unsigned int xhci_port_speed(unsigned int port_status)
{
if (DEV_LOWSPEED(port_status))
return USB_PORT_STAT_LOW_SPEED;
if (DEV_HIGHSPEED(port_status))
return USB_PORT_STAT_HIGH_SPEED;
/*
* FIXME: Yes, we should check for full speed, but the core uses that as
* a default in portspeed() in usb/core/hub.c (which is the only place
* USB_PORT_STAT_*_SPEED is used).
*/
return 0;
}
/*
* These bits are Read Only (RO) and should be saved and written to the
* registers: 0, 3, 10:13, 30
* connect status, over-current status, port speed, and device removable.
* connect status and port speed are also sticky - meaning they're in
* the AUX well and they aren't changed by a hot, warm, or cold reset.
*/
#define XHCI_PORT_RO ((1<<0) | (1<<3) | (0xf<<10) | (1<<30))
/*
* These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
* bits 5:8, 9, 14:15, 25:27
* link state, port power, port indicator state, "wake on" enable state
*/
#define XHCI_PORT_RWS ((0xf<<5) | (1<<9) | (0x3<<14) | (0x7<<25))
/*
* These bits are RW; writing a 1 sets the bit, writing a 0 has no effect:
* bit 4 (port reset)
*/
#define XHCI_PORT_RW1S ((1<<4))
/*
* These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
* bits 1, 17, 18, 19, 20, 21, 22, 23
* port enable/disable, and
* change bits: connect, PED, warm port reset changed (reserved zero for USB 2.0 ports),
* over-current, reset, link state, and L1 change
*/
#define XHCI_PORT_RW1CS ((1<<1) | (0x7f<<17))
/*
* Bit 16 is RW, and writing a '1' to it causes the link state control to be
* latched in
*/
#define XHCI_PORT_RW ((1<<16))
/*
* These bits are Reserved Zero (RsvdZ) and zero should be written to them:
* bits 2, 24, 28:31
*/
#define XHCI_PORT_RZ ((1<<2) | (1<<24) | (0xf<<28))
/*
* Given a port state, this function returns a value that would result in the
* port being in the same state, if the value was written to the port status
* control register.
* Save Read Only (RO) bits and save read/write bits where
* writing a 0 clears the bit and writing a 1 sets the bit (RWS).
* For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
*/
u32 xhci_port_state_to_neutral(u32 state)
{
/* Save read-only status and port state */
return (state & XHCI_PORT_RO) | (state & XHCI_PORT_RWS);
}
/*
* find slot id based on port number.
* @port: The one-based port number from one of the two split roothubs.
*/
int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
u16 port)
{
int slot_id;
int i;
enum usb_device_speed speed;
slot_id = 0;
for (i = 0; i < MAX_HC_SLOTS; i++) {
if (!xhci->devs[i] || !xhci->devs[i]->udev)
continue;
speed = xhci->devs[i]->udev->speed;
if (((speed >= USB_SPEED_SUPER) == (hcd->speed >= HCD_USB3))
&& xhci->devs[i]->fake_port == port) {
slot_id = i;
break;
}
}
return slot_id;
}
/*
* Stop device
* It issues stop endpoint command for EP 0 to 30. And wait the last command
* to complete.
* suspend will set to 1, if suspend bit need to set in command.
*/
static int xhci_stop_device(struct xhci_hcd *xhci, int slot_id, int suspend)
{
struct xhci_virt_device *virt_dev;
struct xhci_command *cmd;
unsigned long flags;
int ret;
int i;
ret = 0;
cmd = xhci_alloc_command(xhci, false, true, GFP_NOIO);
if (!cmd) {
xhci_dbg(xhci, "Couldn't allocate command structure.\n");
return -ENOMEM;
}
spin_lock_irqsave(&xhci->lock, flags);
virt_dev = xhci->devs[slot_id];
if (!virt_dev) {
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_free_command(xhci, cmd);
return -ENODEV;
}
for (i = LAST_EP_INDEX; i > 0; i--) {
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue) {
struct xhci_command *command;
command = xhci_alloc_command(xhci, false, false,
GFP_NOWAIT);
if (!command) {
spin_unlock_irqrestore(&xhci->lock, flags);
ret = -ENOMEM;
goto cmd_cleanup;
}
ret = xhci_queue_stop_endpoint(xhci, command, slot_id,
i, suspend);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_free_command(xhci, command);
goto cmd_cleanup;
}
}
}
ret = xhci_queue_stop_endpoint(xhci, cmd, slot_id, 0, suspend);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
goto cmd_cleanup;
}
xhci_ring_cmd_db(xhci);
spin_unlock_irqrestore(&xhci->lock, flags);
/* Wait for last stop endpoint command to finish */
wait_for_completion(cmd->completion);
if (cmd->status == COMP_CMD_ABORT || cmd->status == COMP_CMD_STOP) {
xhci_warn(xhci, "Timeout while waiting for stop endpoint command\n");
ret = -ETIME;
}
cmd_cleanup:
xhci_free_command(xhci, cmd);
return ret;
}
/*
* Ring device, it rings the all doorbells unconditionally.
*/
void xhci_ring_device(struct xhci_hcd *xhci, int slot_id)
{
int i, s;
struct xhci_virt_ep *ep;
for (i = 0; i < LAST_EP_INDEX + 1; i++) {
ep = &xhci->devs[slot_id]->eps[i];
if (ep->ep_state & EP_HAS_STREAMS) {
for (s = 1; s < ep->stream_info->num_streams; s++)
xhci_ring_ep_doorbell(xhci, slot_id, i, s);
} else if (ep->ring && ep->ring->dequeue) {
xhci_ring_ep_doorbell(xhci, slot_id, i, 0);
}
}
return;
}
static void xhci_disable_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
u16 wIndex, __le32 __iomem *addr, u32 port_status)
{
/* Don't allow the USB core to disable SuperSpeed ports. */
if (hcd->speed >= HCD_USB3) {
xhci_dbg(xhci, "Ignoring request to disable "
"SuperSpeed port.\n");
return;
}
if (xhci->quirks & XHCI_BROKEN_PORT_PED) {
xhci_dbg(xhci,
"Broken Port Enabled/Disabled, ignoring port disable request.\n");
return;
}
/* Write 1 to disable the port */
writel(port_status | PORT_PE, addr);
port_status = readl(addr);
xhci_dbg(xhci, "disable port, actual port %d status = 0x%x\n",
wIndex, port_status);
}
static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue,
u16 wIndex, __le32 __iomem *addr, u32 port_status)
{
char *port_change_bit;
u32 status;
switch (wValue) {
case USB_PORT_FEAT_C_RESET:
status = PORT_RC;
port_change_bit = "reset";
break;
case USB_PORT_FEAT_C_BH_PORT_RESET:
status = PORT_WRC;
port_change_bit = "warm(BH) reset";
break;
case USB_PORT_FEAT_C_CONNECTION:
status = PORT_CSC;
port_change_bit = "connect";
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
status = PORT_OCC;
port_change_bit = "over-current";
break;
case USB_PORT_FEAT_C_ENABLE:
status = PORT_PEC;
port_change_bit = "enable/disable";
break;
case USB_PORT_FEAT_C_SUSPEND:
status = PORT_PLC;
port_change_bit = "suspend/resume";
break;
case USB_PORT_FEAT_C_PORT_LINK_STATE:
status = PORT_PLC;
port_change_bit = "link state";
break;
case USB_PORT_FEAT_C_PORT_CONFIG_ERROR:
status = PORT_CEC;
port_change_bit = "config error";
break;
default:
/* Should never happen */
return;
}
/* Change bits are all write 1 to clear */
writel(port_status | status, addr);
port_status = readl(addr);
xhci_dbg(xhci, "clear port %s change, actual port %d status = 0x%x\n",
port_change_bit, wIndex, port_status);
}
static int xhci_get_ports(struct usb_hcd *hcd, __le32 __iomem ***port_array)
{
int max_ports;
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
if (hcd->speed >= HCD_USB3) {
max_ports = xhci->num_usb3_ports;
*port_array = xhci->usb3_ports;
} else {
max_ports = xhci->num_usb2_ports;
*port_array = xhci->usb2_ports;
}
return max_ports;
}
void xhci_set_link_state(struct xhci_hcd *xhci, __le32 __iomem **port_array,
int port_id, u32 link_state)
{
u32 temp;
temp = readl(port_array[port_id]);
temp = xhci_port_state_to_neutral(temp);
temp &= ~PORT_PLS_MASK;
temp |= PORT_LINK_STROBE | link_state;
writel(temp, port_array[port_id]);
}
static void xhci_set_remote_wake_mask(struct xhci_hcd *xhci,
__le32 __iomem **port_array, int port_id, u16 wake_mask)
{
u32 temp;
temp = readl(port_array[port_id]);
temp = xhci_port_state_to_neutral(temp);
if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_CONNECT)
temp |= PORT_WKCONN_E;
else
temp &= ~PORT_WKCONN_E;
if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT)
temp |= PORT_WKDISC_E;
else
temp &= ~PORT_WKDISC_E;
if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT)
temp |= PORT_WKOC_E;
else
temp &= ~PORT_WKOC_E;
writel(temp, port_array[port_id]);
}
/* Test and clear port RWC bit */
void xhci_test_and_clear_bit(struct xhci_hcd *xhci, __le32 __iomem **port_array,
int port_id, u32 port_bit)
{
u32 temp;
temp = readl(port_array[port_id]);
if (temp & port_bit) {
temp = xhci_port_state_to_neutral(temp);
temp |= port_bit;
writel(temp, port_array[port_id]);
}
}
/* Updates Link Status for USB 2.1 port */
static void xhci_hub_report_usb2_link_state(u32 *status, u32 status_reg)
{
if ((status_reg & PORT_PLS_MASK) == XDEV_U2)
*status |= USB_PORT_STAT_L1;
}
/* Updates Link Status for super Speed port */
static void xhci_hub_report_usb3_link_state(struct xhci_hcd *xhci,
u32 *status, u32 status_reg)
{
u32 pls = status_reg & PORT_PLS_MASK;
/* resume state is a xHCI internal state.
* Do not report it to usb core, instead, pretend to be U3,
* thus usb core knows it's not ready for transfer
*/
if (pls == XDEV_RESUME) {
*status |= USB_SS_PORT_LS_U3;
return;
}
/* When the CAS bit is set then warm reset
* should be performed on port
*/
if (status_reg & PORT_CAS) {
/* The CAS bit can be set while the port is
* in any link state.
* Only roothubs have CAS bit, so we
* pretend to be in compliance mode
* unless we're already in compliance
* or the inactive state.
*/
if (pls != USB_SS_PORT_LS_COMP_MOD &&
pls != USB_SS_PORT_LS_SS_INACTIVE) {
pls = USB_SS_PORT_LS_COMP_MOD;
}
/* Return also connection bit -
* hub state machine resets port
* when this bit is set.
*/
pls |= USB_PORT_STAT_CONNECTION;
} else {
/*
* If CAS bit isn't set but the Port is already at
* Compliance Mode, fake a connection so the USB core
* notices the Compliance state and resets the port.
* This resolves an issue generated by the SN65LVPE502CP
* in which sometimes the port enters compliance mode
* caused by a delay on the host-device negotiation.
*/
if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
(pls == USB_SS_PORT_LS_COMP_MOD))
pls |= USB_PORT_STAT_CONNECTION;
}
/* update status field */
*status |= pls;
}
/*
* Function for Compliance Mode Quirk.
*
* This Function verifies if all xhc USB3 ports have entered U0, if so,
* the compliance mode timer is deleted. A port won't enter
* compliance mode if it has previously entered U0.
*/
static void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status,
u16 wIndex)
{
u32 all_ports_seen_u0 = ((1 << xhci->num_usb3_ports)-1);
bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0);
if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK))
return;
if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) {
xhci->port_status_u0 |= 1 << wIndex;
if (xhci->port_status_u0 == all_ports_seen_u0) {
del_timer_sync(&xhci->comp_mode_recovery_timer);
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"All USB3 ports have entered U0 already!");
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"Compliance Mode Recovery Timer Deleted.");
}
}
}
static u32 xhci_get_ext_port_status(u32 raw_port_status, u32 port_li)
{
u32 ext_stat = 0;
int speed_id;
/* only support rx and tx lane counts of 1 in usb3.1 spec */
speed_id = DEV_PORT_SPEED(raw_port_status);
ext_stat |= speed_id; /* bits 3:0, RX speed id */
ext_stat |= speed_id << 4; /* bits 7:4, TX speed id */
ext_stat |= PORT_RX_LANES(port_li) << 8; /* bits 11:8 Rx lane count */
ext_stat |= PORT_TX_LANES(port_li) << 12; /* bits 15:12 Tx lane count */
return ext_stat;
}
/*
* Converts a raw xHCI port status into the format that external USB 2.0 or USB
* 3.0 hubs use.
*
* Possible side effects:
* - Mark a port as being done with device resume,
* and ring the endpoint doorbells.
* - Stop the Synopsys redriver Compliance Mode polling.
* - Drop and reacquire the xHCI lock, in order to wait for port resume.
*/
static u32 xhci_get_port_status(struct usb_hcd *hcd,
struct xhci_bus_state *bus_state,
__le32 __iomem **port_array,
u16 wIndex, u32 raw_port_status,
unsigned long flags)
__releases(&xhci->lock)
__acquires(&xhci->lock)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
u32 status = 0;
int slot_id;
/* wPortChange bits */
if (raw_port_status & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (raw_port_status & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if ((raw_port_status & PORT_OCC))
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
if ((raw_port_status & PORT_RC))
status |= USB_PORT_STAT_C_RESET << 16;
/* USB3.0 only */
if (hcd->speed >= HCD_USB3) {
/* Port link change with port in resume state should not be
* reported to usbcore, as this is an internal state to be
* handled by xhci driver. Reporting PLC to usbcore may
* cause usbcore clearing PLC first and port change event
* irq won't be generated.
*/
if ((raw_port_status & PORT_PLC) &&
(raw_port_status & PORT_PLS_MASK) != XDEV_RESUME)
status |= USB_PORT_STAT_C_LINK_STATE << 16;
if ((raw_port_status & PORT_WRC))
status |= USB_PORT_STAT_C_BH_RESET << 16;
if ((raw_port_status & PORT_CEC))
status |= USB_PORT_STAT_C_CONFIG_ERROR << 16;
}
if (hcd->speed < HCD_USB3) {
if ((raw_port_status & PORT_PLS_MASK) == XDEV_U3
&& (raw_port_status & PORT_POWER))
status |= USB_PORT_STAT_SUSPEND;
}
if ((raw_port_status & PORT_PLS_MASK) == XDEV_RESUME &&
!DEV_SUPERSPEED_ANY(raw_port_status)) {
if ((raw_port_status & PORT_RESET) ||
!(raw_port_status & PORT_PE))
return 0xffffffff;
/* did port event handler already start resume timing? */
if (!bus_state->resume_done[wIndex]) {
/* If not, maybe we are in a host initated resume? */
if (test_bit(wIndex, &bus_state->resuming_ports)) {
/* Host initated resume doesn't time the resume
* signalling using resume_done[].
* It manually sets RESUME state, sleeps 20ms
* and sets U0 state. This should probably be
* changed, but not right now.
*/
} else {
/* port resume was discovered now and here,
* start resume timing
*/
unsigned long timeout = jiffies +
msecs_to_jiffies(USB_RESUME_TIMEOUT);
set_bit(wIndex, &bus_state->resuming_ports);
bus_state->resume_done[wIndex] = timeout;
mod_timer(&hcd->rh_timer, timeout);
}
/* Has resume been signalled for USB_RESUME_TIME yet? */
} else if (time_after_eq(jiffies,
bus_state->resume_done[wIndex])) {
int time_left;
xhci_dbg(xhci, "Resume USB2 port %d\n",
wIndex + 1);
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
set_bit(wIndex, &bus_state->rexit_ports);
xhci_test_and_clear_bit(xhci, port_array, wIndex,
PORT_PLC);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
spin_unlock_irqrestore(&xhci->lock, flags);
time_left = wait_for_completion_timeout(
&bus_state->rexit_done[wIndex],
msecs_to_jiffies(
XHCI_MAX_REXIT_TIMEOUT));
spin_lock_irqsave(&xhci->lock, flags);
if (time_left) {
slot_id = xhci_find_slot_id_by_port(hcd,
xhci, wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
return 0xffffffff;
}
xhci_ring_device(xhci, slot_id);
} else {
int port_status = readl(port_array[wIndex]);
xhci_warn(xhci, "Port resume took longer than %i msec, port status = 0x%x\n",
XHCI_MAX_REXIT_TIMEOUT,
port_status);
status |= USB_PORT_STAT_SUSPEND;
clear_bit(wIndex, &bus_state->rexit_ports);
}
bus_state->port_c_suspend |= 1 << wIndex;
bus_state->suspended_ports &= ~(1 << wIndex);
} else {
/*
* The resume has been signaling for less than
* USB_RESUME_TIME. Report the port status as SUSPEND,
* let the usbcore check port status again and clear
* resume signaling later.
*/
status |= USB_PORT_STAT_SUSPEND;
}
}
/*
* Clear stale usb2 resume signalling variables in case port changed
* state during resume signalling. For example on error
*/
if ((bus_state->resume_done[wIndex] ||
test_bit(wIndex, &bus_state->resuming_ports)) &&
(raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
(raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) {
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
}
if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0 &&
(raw_port_status & PORT_POWER)) {
if (bus_state->suspended_ports & (1 << wIndex)) {
bus_state->suspended_ports &= ~(1 << wIndex);
if (hcd->speed < HCD_USB3)
bus_state->port_c_suspend |= 1 << wIndex;
}
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
}
if (raw_port_status & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
status |= xhci_port_speed(raw_port_status);
}
if (raw_port_status & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
if (raw_port_status & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (raw_port_status & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (raw_port_status & PORT_POWER) {
if (hcd->speed >= HCD_USB3)
status |= USB_SS_PORT_STAT_POWER;
else
status |= USB_PORT_STAT_POWER;
}
/* Update Port Link State */
if (hcd->speed >= HCD_USB3) {
xhci_hub_report_usb3_link_state(xhci, &status, raw_port_status);
/*
* Verify if all USB3 Ports Have entered U0 already.
* Delete Compliance Mode Timer if so.
*/
xhci_del_comp_mod_timer(xhci, raw_port_status, wIndex);
} else {
xhci_hub_report_usb2_link_state(&status, raw_port_status);
}
if (bus_state->port_c_suspend & (1 << wIndex))
status |= USB_PORT_STAT_C_SUSPEND << 16;
return status;
}
static void xhci_single_step_completion(struct urb *urb)
{
struct completion *done = urb->context;
complete(done);
}
/*
* Allocate a URB and initialize the various fields of it.
* This API is used by the single_step_set_feature test of
* EHSET where IN packet of the GetDescriptor request is
* sent 15secs after the SETUP packet.
* Return NULL if failed.
*/
static struct urb *xhci_request_single_step_set_feature_urb(
struct usb_device *udev,
void *dr,
void *buf,
struct completion *done)
{
struct urb *urb;
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
struct usb_host_endpoint *ep;
urb = usb_alloc_urb(0, GFP_KERNEL);
if (!urb)
return NULL;
urb->pipe = usb_rcvctrlpipe(udev, 0);
ep = udev->ep_in[usb_pipeendpoint(urb->pipe)];
if (!ep) {
usb_free_urb(urb);
return NULL;
}
/*
* Initialize the various URB fields as these are used by the HCD
* driver to queue it and as well as when completion happens.
*/
urb->ep = ep;
urb->dev = udev;
urb->setup_packet = dr;
urb->transfer_buffer = buf;
urb->transfer_buffer_length = USB_DT_DEVICE_SIZE;
urb->complete = xhci_single_step_completion;
urb->status = -EINPROGRESS;
urb->actual_length = 0;
urb->transfer_flags = URB_DIR_IN;
usb_get_urb(urb);
atomic_inc(&urb->use_count);
atomic_inc(&urb->dev->urbnum);
usb_hcd_map_urb_for_dma(hcd, urb, GFP_KERNEL);
urb->context = done;
return urb;
}
/*
* This function implements the USB_PORT_FEAT_TEST handling of the
* SINGLE_STEP_SET_FEATURE test mode as defined in the Embedded
* High-Speed Electrical Test (EHSET) specification. This simply
* issues a GetDescriptor control transfer, with an inserted 15-second
* delay after the end of the SETUP stage and before the IN token of
* the DATA stage is set. The idea is that this gives the test operator
* enough time to configure the oscilloscope to perform a measurement
* of the response time between the DATA and ACK packets that follow.
*/
static int xhci_ehset_single_step_set_feature(struct usb_hcd *hcd, int port)
{
int retval;
struct usb_ctrlrequest *dr;
struct urb *urb;
struct usb_device *udev;
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
struct usb_device_descriptor *buf;
unsigned long flags;
DECLARE_COMPLETION_ONSTACK(done);
/* Obtain udev of the rhub's child port */
udev = usb_hub_find_child(hcd->self.root_hub, port);
if (!udev) {
xhci_err(xhci, "No device attached to the RootHub\n");
return -ENODEV;
}
buf = kmalloc(USB_DT_DEVICE_SIZE, GFP_KERNEL);
if (!buf)
return -ENOMEM;
dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_KERNEL);
if (!dr) {
kfree(buf);
return -ENOMEM;
}
/* Fill Setup packet for GetDescriptor */
dr->bRequestType = USB_DIR_IN;
dr->bRequest = USB_REQ_GET_DESCRIPTOR;
dr->wValue = cpu_to_le16(USB_DT_DEVICE << 8);
dr->wIndex = 0;
dr->wLength = cpu_to_le16(USB_DT_DEVICE_SIZE);
urb = xhci_request_single_step_set_feature_urb(udev, dr, buf, &done);
if (!urb) {
retval = -ENOMEM;
goto cleanup;
}
/* Now complete just the SETUP stage */
spin_lock_irqsave(&xhci->lock, flags);
retval = xhci_submit_single_step_set_feature(hcd, urb, 1);
spin_unlock_irqrestore(&xhci->lock, flags);
if (retval)
goto out1;
if (!wait_for_completion_timeout(&done, msecs_to_jiffies(2000))) {
usb_kill_urb(urb);
retval = -ETIMEDOUT;
xhci_err(xhci, "%s SETUP stage timed out on ep0\n", __func__);
goto out1;
}
/* Sleep for 15 seconds; HC will send SOFs during this period */
msleep(15 * 1000);
/* Complete remaining DATA and status stages. Re-use same URB */
urb->status = -EINPROGRESS;
usb_get_urb(urb);
atomic_inc(&urb->use_count);
atomic_inc(&urb->dev->urbnum);
spin_lock_irqsave(&xhci->lock, flags);
retval = xhci_submit_single_step_set_feature(hcd, urb, 0);
spin_unlock_irqrestore(&xhci->lock, flags);
if (!retval && !wait_for_completion_timeout(&done,
msecs_to_jiffies(2000))) {
usb_kill_urb(urb);
retval = -ETIMEDOUT;
xhci_err(xhci, "%s IN stage timed out on ep0\n", __func__);
}
out1:
usb_free_urb(urb);
cleanup:
kfree(dr);
kfree(buf);
return retval;
}
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u16 wIndex, char *buf, u16 wLength)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports;
unsigned long flags;
u32 temp, status;
int retval = 0;
__le32 __iomem **port_array;
int slot_id;
struct xhci_bus_state *bus_state;
u16 link_state = 0;
u16 wake_mask = 0;
u16 timeout = 0;
u16 test_mode = 0;
enum usb_device_speed s = hcd->self.root_hub->speed;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
spin_lock_irqsave(&xhci->lock, flags);
switch (typeReq) {
case GetHubStatus:
/* No power source, over-current reported per port */
memset(buf, 0, 4);
break;
case GetHubDescriptor:
/* Check to make sure userspace is asking for the USB 3.0 hub
* descriptor for the USB 3.0 roothub. If not, we stall the
* endpoint, like external hubs do.
*/
if (hcd->speed >= HCD_USB3 &&
(wLength < USB_DT_SS_HUB_SIZE ||
wValue != (USB_DT_SS_HUB << 8))) {
xhci_dbg(xhci, "Wrong hub descriptor type for "
"USB 3.0 roothub.\n");
goto error;
}
xhci_hub_descriptor(hcd, xhci,
(struct usb_hub_descriptor *) buf);
break;
case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
if ((wValue & 0xff00) != (USB_DT_BOS << 8))
goto error;
if (hcd->speed < HCD_USB3)
goto error;
retval = xhci_create_usb3_bos_desc(xhci, buf, wLength);
spin_unlock_irqrestore(&xhci->lock, flags);
return retval;
case GetPortStatus:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = readl(port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
status = xhci_get_port_status(hcd, bus_state, port_array,
wIndex, temp, flags);
if (status == 0xffffffff)
goto error;
xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n",
wIndex, temp);
xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
/* if USB 3.1 extended port status return additional 4 bytes */
if (wValue == 0x02) {
u32 port_li;
if (hcd->speed < HCD_USB31 || wLength != 8) {
xhci_err(xhci, "get ext port status invalid parameter\n");
retval = -EINVAL;
break;
}
port_li = readl(port_array[wIndex] + PORTLI);
status = xhci_get_ext_port_status(temp, port_li);
put_unaligned_le32(cpu_to_le32(status), &buf[4]);
}
break;
case SetPortFeature:
if (wValue == USB_PORT_FEAT_LINK_STATE)
link_state = (wIndex & 0xff00) >> 3;
if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK)
wake_mask = wIndex & 0xff00;
/* The MSB of wIndex is the U1/U2 timeout OR TEST mode*/
test_mode = timeout = (wIndex & 0xff00) >> 8;
wIndex &= 0xff;
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = readl(port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
temp = xhci_port_state_to_neutral(temp);
/* FIXME: What new port features do we need to support? */
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = readl(port_array[wIndex]);
if ((temp & PORT_PLS_MASK) != XDEV_U0) {
/* Resume the port to U0 first */
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10);
spin_lock_irqsave(&xhci->lock, flags);
}
/* In spec software should not attempt to suspend
* a port unless the port reports that it is in the
* enabled (PED = ‘1’,PLS < ‘3’) state.
*/
temp = readl(port_array[wIndex]);
if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
xhci_warn(xhci, "USB core suspending device "
"not in U0/U1/U2.\n");
goto error;
}
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_warn(xhci, "slot_id is zero\n");
goto error;
}
/* unlock to execute stop endpoint commands */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex, XDEV_U3);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = readl(port_array[wIndex]);
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_LINK_STATE:
temp = readl(port_array[wIndex]);
/* Disable port */
if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
xhci_dbg(xhci, "Disable port %d\n", wIndex);
temp = xhci_port_state_to_neutral(temp);
/*
* Clear all change bits, so that we get a new
* connection event.
*/
temp |= PORT_CSC | PORT_PEC | PORT_WRC |
PORT_OCC | PORT_RC | PORT_PLC |
PORT_CEC;
writel(temp | PORT_PE, port_array[wIndex]);
temp = readl(port_array[wIndex]);
break;
}
/* Put link in RxDetect (enable port) */
if (link_state == USB_SS_PORT_LS_RX_DETECT) {
xhci_dbg(xhci, "Enable port %d\n", wIndex);
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
temp = readl(port_array[wIndex]);
break;
}
/*
* For xHCI 1.1 according to section 4.19.1.2.4.1 a
* root hub port's transition to compliance mode upon
* detecting LFPS timeout may be controlled by an
* Compliance Transition Enabled (CTE) flag (not
* software visible). This flag is set by writing 0xA
* to PORTSC PLS field which will allow transition to
* compliance mode the next time LFPS timeout is
* encountered. A warm reset will clear it.
*
* The CTE flag is only supported if the HCCPARAMS2 CTC
* flag is set, otherwise, the compliance substate is
* automatically entered as on 1.0 and prior.
*/
if (link_state == USB_SS_PORT_LS_COMP_MOD) {
if (!HCC2_CTC(xhci->hcc_params2)) {
xhci_dbg(xhci, "CTC flag is 0, port already supports entering compliance mode\n");
break;
}
if ((temp & PORT_CONNECT)) {
xhci_warn(xhci, "Can't set compliance mode when port is connected\n");
goto error;
}
xhci_dbg(xhci, "Enable compliance mode transition for port %d\n",
wIndex);
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
temp = readl(port_array[wIndex]);
break;
}
/* Software should not attempt to set
* port link state above '3' (U3) and the port
* must be enabled.
*/
if ((temp & PORT_PE) == 0 ||
(link_state > USB_SS_PORT_LS_U3)) {
xhci_warn(xhci, "Cannot set link state.\n");
goto error;
}
if (link_state == USB_SS_PORT_LS_U3) {
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (slot_id) {
/* unlock to execute stop endpoint
* commands */
spin_unlock_irqrestore(&xhci->lock,
flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
}
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = readl(port_array[wIndex]);
if (link_state == USB_SS_PORT_LS_U3)
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_POWER:
/*
* Turn on ports, even if there isn't per-port switching.
* HC will report connect events even before this is set.
* However, hub_wq will ignore the roothub events until
* the roothub is registered.
*/
writel(temp | PORT_POWER, port_array[wIndex]);
temp = readl(port_array[wIndex]);
xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
spin_unlock_irqrestore(&xhci->lock, flags);
temp = usb_acpi_power_manageable(hcd->self.root_hub,
wIndex);
if (temp)
usb_acpi_set_power_state(hcd->self.root_hub,
wIndex, true);
spin_lock_irqsave(&xhci->lock, flags);
break;
case USB_PORT_FEAT_RESET:
temp = (temp | PORT_RESET);
writel(temp, port_array[wIndex]);
temp = readl(port_array[wIndex]);
if (s == USB_SPEED_HIGH)
usb_phy_start_port_reset(hcd->usb_phy);
xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_REMOTE_WAKE_MASK:
xhci_set_remote_wake_mask(xhci, port_array,
wIndex, wake_mask);
temp = readl(port_array[wIndex]);
xhci_dbg(xhci, "set port remote wake mask, "
"actual port %d status = 0x%x\n",
wIndex, temp);
break;
case USB_PORT_FEAT_BH_PORT_RESET:
temp |= PORT_WR;
writel(temp, port_array[wIndex]);
temp = readl(port_array[wIndex]);
break;
case USB_PORT_FEAT_U1_TIMEOUT:
if (hcd->speed < HCD_USB3)
goto error;
temp = readl(port_array[wIndex] + PORTPMSC);
temp &= ~PORT_U1_TIMEOUT_MASK;
temp |= PORT_U1_TIMEOUT(timeout);
writel(temp, port_array[wIndex] + PORTPMSC);
break;
case USB_PORT_FEAT_U2_TIMEOUT:
if (hcd->speed < HCD_USB3)
goto error;
temp = readl(port_array[wIndex] + PORTPMSC);
temp &= ~PORT_U2_TIMEOUT_MASK;
temp |= PORT_U2_TIMEOUT(timeout);
writel(temp, port_array[wIndex] + PORTPMSC);
break;
case USB_PORT_FEAT_TEST:
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (test_mode && test_mode <= 5) {
/* unlock to execute stop endpoint commands */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
xhci_halt(xhci);
temp = readl_relaxed(port_array[wIndex] +
PORTPMSC);
temp |= test_mode << 28;
writel_relaxed(temp, port_array[wIndex] +
PORTPMSC);
/* to make sure above write goes through */
mb();
} else if (test_mode == 6) {
spin_unlock_irqrestore(&xhci->lock, flags);
retval = xhci_ehset_single_step_set_feature(hcd,
wIndex);
spin_lock_irqsave(&xhci->lock, flags);
} else {
goto error;
}
break;
default:
goto error;
}
/* unblock any posted writes */
temp = readl(port_array[wIndex]);
break;
case ClearPortFeature:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = readl(port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
/* FIXME: What new port features do we need to support? */
temp = xhci_port_state_to_neutral(temp);
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = readl(port_array[wIndex]);
xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
xhci_dbg(xhci, "PORTSC %04x\n", temp);
if (temp & PORT_RESET)
goto error;
if ((temp & PORT_PLS_MASK) == XDEV_U3) {
if ((temp & PORT_PE) == 0)
goto error;
set_bit(wIndex, &bus_state->resuming_ports);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_RESUME);
spin_unlock_irqrestore(&xhci->lock, flags);
usleep_range(21000, 21500);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
clear_bit(wIndex, &bus_state->resuming_ports);
}
bus_state->port_c_suspend |= 1 << wIndex;
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
break;
case USB_PORT_FEAT_C_SUSPEND:
bus_state->port_c_suspend &= ~(1 << wIndex);
case USB_PORT_FEAT_C_RESET:
case USB_PORT_FEAT_C_BH_PORT_RESET:
case USB_PORT_FEAT_C_CONNECTION:
case USB_PORT_FEAT_C_OVER_CURRENT:
case USB_PORT_FEAT_C_ENABLE:
case USB_PORT_FEAT_C_PORT_LINK_STATE:
case USB_PORT_FEAT_C_PORT_CONFIG_ERROR:
xhci_clear_port_change_bit(xhci, wValue, wIndex,
port_array[wIndex], temp);
break;
case USB_PORT_FEAT_ENABLE:
xhci_disable_port(hcd, xhci, wIndex,
port_array[wIndex], temp);
break;
case USB_PORT_FEAT_POWER:
writel(temp & ~PORT_POWER, port_array[wIndex]);
spin_unlock_irqrestore(&xhci->lock, flags);
temp = usb_acpi_power_manageable(hcd->self.root_hub,
wIndex);
if (temp)
usb_acpi_set_power_state(hcd->self.root_hub,
wIndex, false);
spin_lock_irqsave(&xhci->lock, flags);
break;
default:
goto error;
}
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore(&xhci->lock, flags);
return retval;
}
/*
* Returns 0 if the status hasn't changed, or the number of bytes in buf.
* Ports are 0-indexed from the HCD point of view,
* and 1-indexed from the USB core pointer of view.
*
* Note that the status change bits will be cleared as soon as a port status
* change event is generated, so we use the saved status from that event.
*/
int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
{
unsigned long flags;
u32 temp, status;
u32 mask;
int i, retval;
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports;
__le32 __iomem **port_array;
struct xhci_bus_state *bus_state;
bool reset_change = false;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
/* Initial status is no changes */
retval = (max_ports + 8) / 8;
memset(buf, 0, retval);
/*
* Inform the usbcore about resume-in-progress by returning
* a non-zero value even if there are no status changes.
*/
status = bus_state->resuming_ports;
mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC;
spin_lock_irqsave(&xhci->lock, flags);
/* For each port, did anything change? If so, set that bit in buf. */
for (i = 0; i < max_ports; i++) {
temp = readl(port_array[i]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
if ((temp & mask) != 0 ||
(bus_state->port_c_suspend & 1 << i) ||
(bus_state->resume_done[i] && time_after_eq(
jiffies, bus_state->resume_done[i]))) {
buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
status = 1;
}
if ((temp & PORT_RC))
reset_change = true;
}
if (!status && !reset_change) {
xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
}
spin_unlock_irqrestore(&xhci->lock, flags);
return status ? retval : 0;
}
#ifdef CONFIG_PM
int xhci_bus_suspend(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports, port_index;
__le32 __iomem **port_array;
struct xhci_bus_state *bus_state;
unsigned long flags;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
spin_lock_irqsave(&xhci->lock, flags);
if (hcd->self.root_hub->do_remote_wakeup) {
if (bus_state->resuming_ports || /* USB2 */
bus_state->port_remote_wakeup) { /* USB3 */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_dbg(xhci, "suspend failed because a port is resuming\n");
return -EBUSY;
}
}
port_index = max_ports;
bus_state->bus_suspended = 0;
while (port_index--) {
/* suspend the port if the port is not suspended */
u32 t1, t2;
int slot_id;
t1 = readl(port_array[port_index]);
t2 = xhci_port_state_to_neutral(t1);
if ((t1 & PORT_PE) && !(t1 & PORT_PLS_MASK)) {
xhci_dbg(xhci, "port %d not suspended\n", port_index);
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
port_index + 1);
if (slot_id) {
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
t2 &= ~PORT_PLS_MASK;
t2 |= PORT_LINK_STROBE | XDEV_U3;
set_bit(port_index, &bus_state->bus_suspended);
}
/* USB core sets remote wake mask for USB 3.0 hubs,
* including the USB 3.0 roothub, but only if CONFIG_PM
* is enabled, so also enable remote wake here.
*/
if (hcd->self.root_hub->do_remote_wakeup) {
if (t1 & PORT_CONNECT) {
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
t2 &= ~PORT_WKCONN_E;
} else {
t2 |= PORT_WKOC_E | PORT_WKCONN_E;
t2 &= ~PORT_WKDISC_E;
}
} else
t2 &= ~PORT_WAKE_BITS;
t1 = xhci_port_state_to_neutral(t1);
if (t1 != t2)
writel(t2, port_array[port_index]);
}
hcd->state = HC_STATE_SUSPENDED;
bus_state->next_statechange = jiffies + msecs_to_jiffies(10);
spin_unlock_irqrestore(&xhci->lock, flags);
return 0;
}
/*
* Workaround for missing Cold Attach Status (CAS) if device re-plugged in S3.
* warm reset a USB3 device stuck in polling or compliance mode after resume.
* See Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
*/
static bool xhci_port_missing_cas_quirk(int port_index,
__le32 __iomem **port_array)
{
u32 portsc;
portsc = readl(port_array[port_index]);
/* if any of these are set we are not stuck */
if (portsc & (PORT_CONNECT | PORT_CAS))
return false;
if (((portsc & PORT_PLS_MASK) != XDEV_POLLING) &&
((portsc & PORT_PLS_MASK) != XDEV_COMP_MODE))
return false;
/* clear wakeup/change bits, and do a warm port reset */
portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
portsc |= PORT_WR;
writel(portsc, port_array[port_index]);
/* flush write */
readl(port_array[port_index]);
return true;
}
int xhci_bus_resume(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports, port_index;
__le32 __iomem **port_array;
struct xhci_bus_state *bus_state;
u32 temp;
unsigned long flags;
unsigned long port_was_suspended = 0;
bool need_usb2_u3_exit = false;
int slot_id;
int sret;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
if (time_before(jiffies, bus_state->next_statechange))
msleep(5);
spin_lock_irqsave(&xhci->lock, flags);
if (!HCD_HW_ACCESSIBLE(hcd)) {
spin_unlock_irqrestore(&xhci->lock, flags);
return -ESHUTDOWN;
}
/* delay the irqs */
temp = readl(&xhci->op_regs->command);
temp &= ~CMD_EIE;
writel(temp, &xhci->op_regs->command);
port_index = max_ports;
while (port_index--) {
/* Check whether need resume ports. If needed
resume port and disable remote wakeup */
u32 temp;
temp = readl(port_array[port_index]);
/* warm reset CAS limited ports stuck in polling/compliance */
if ((xhci->quirks & XHCI_MISSING_CAS) &&
(hcd->speed >= HCD_USB3) &&
xhci_port_missing_cas_quirk(port_index, port_array)) {
xhci_dbg(xhci, "reset stuck port %d\n", port_index);
continue;
}
if (DEV_SUPERSPEED_ANY(temp))
temp &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
else
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
if (test_bit(port_index, &bus_state->bus_suspended) &&
(temp & PORT_PLS_MASK)) {
set_bit(port_index, &port_was_suspended);
if (!DEV_SUPERSPEED_ANY(temp)) {
xhci_set_link_state(xhci, port_array,
port_index, XDEV_RESUME);
need_usb2_u3_exit = true;
}
} else
writel(temp, port_array[port_index]);
}
if (need_usb2_u3_exit) {
spin_unlock_irqrestore(&xhci->lock, flags);
usleep_range(21000, 21500);
spin_lock_irqsave(&xhci->lock, flags);
}
port_index = max_ports;
while (port_index--) {
if (!(port_was_suspended & BIT(port_index)))
continue;
/* Clear PLC to poll it later after XDEV_U0 */
xhci_test_and_clear_bit(xhci, port_array, port_index, PORT_PLC);
xhci_set_link_state(xhci, port_array, port_index, XDEV_U0);
}
port_index = max_ports;
while (port_index--) {
if (!(port_was_suspended & BIT(port_index)))
continue;
/* Poll and Clear PLC */
sret = xhci_handshake(port_array[port_index], PORT_PLC,
PORT_PLC, 10 * 1000);
if (sret)
xhci_warn(xhci, "port %d resume PLC timeout\n",
port_index);
xhci_test_and_clear_bit(xhci, port_array, port_index, PORT_PLC);
slot_id = xhci_find_slot_id_by_port(hcd, xhci, port_index + 1);
if (slot_id)
xhci_ring_device(xhci, slot_id);
}
(void) readl(&xhci->op_regs->command);
bus_state->next_statechange = jiffies + msecs_to_jiffies(5);
/* re-enable irqs */
temp = readl(&xhci->op_regs->command);
temp |= CMD_EIE;
writel(temp, &xhci->op_regs->command);
temp = readl(&xhci->op_regs->command);
spin_unlock_irqrestore(&xhci->lock, flags);
return 0;
}
#endif /* CONFIG_PM */