pinctrl: tegra: add support for rcv-sel and drive type
NVIDIA's Tegra114 added two more configuration parameter in pinmux i.e.
rcv-sel and drive type.
rcv-sel: Select between High and Normal VIL/VIH receivers.
RCVR_SEL=1: High VIL/VIH
RCVR_SEL=0: Normal VIL/VIH
drv_type: Ouptput drive type:
33-50 ohm driver: 0x1
66-100ohm driver: 0x0
Add support of these parameters to be configure from DTS file.
Tegra20 and Tegra30 does not support this configuration and hence initialize their
pinmux structure with reg = -1.
Originally written by Pritesh Raithatha.
Changes by ldewangan:
- remove drvtype_width as it is always 2.
- Better describe the change.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/pinctrl/pinctrl-tegra.c b/drivers/pinctrl/pinctrl-tegra.c
index ae1e4bb..f195d77 100644
--- a/drivers/pinctrl/pinctrl-tegra.c
+++ b/drivers/pinctrl/pinctrl-tegra.c
@@ -201,6 +201,7 @@
{"nvidia,open-drain", TEGRA_PINCONF_PARAM_OPEN_DRAIN},
{"nvidia,lock", TEGRA_PINCONF_PARAM_LOCK},
{"nvidia,io-reset", TEGRA_PINCONF_PARAM_IORESET},
+ {"nvidia,rcv-sel", TEGRA_PINCONF_PARAM_RCV_SEL},
{"nvidia,high-speed-mode", TEGRA_PINCONF_PARAM_HIGH_SPEED_MODE},
{"nvidia,schmitt", TEGRA_PINCONF_PARAM_SCHMITT},
{"nvidia,low-power-mode", TEGRA_PINCONF_PARAM_LOW_POWER_MODE},
@@ -208,6 +209,7 @@
{"nvidia,pull-up-strength", TEGRA_PINCONF_PARAM_DRIVE_UP_STRENGTH},
{"nvidia,slew-rate-falling", TEGRA_PINCONF_PARAM_SLEW_RATE_FALLING},
{"nvidia,slew-rate-rising", TEGRA_PINCONF_PARAM_SLEW_RATE_RISING},
+ {"nvidia,drive-type", TEGRA_PINCONF_PARAM_DRIVE_TYPE},
};
static int tegra_pinctrl_dt_subnode_to_map(struct device *dev,
@@ -450,6 +452,12 @@
*bit = g->ioreset_bit;
*width = 1;
break;
+ case TEGRA_PINCONF_PARAM_RCV_SEL:
+ *bank = g->rcv_sel_bank;
+ *reg = g->rcv_sel_reg;
+ *bit = g->rcv_sel_bit;
+ *width = 1;
+ break;
case TEGRA_PINCONF_PARAM_HIGH_SPEED_MODE:
*bank = g->drv_bank;
*reg = g->drv_reg;
@@ -492,6 +500,12 @@
*bit = g->slwr_bit;
*width = g->slwr_width;
break;
+ case TEGRA_PINCONF_PARAM_DRIVE_TYPE:
+ *bank = g->drvtype_bank;
+ *reg = g->drvtype_reg;
+ *bit = g->drvtype_bit;
+ *width = 2;
+ break;
default:
dev_err(pmx->dev, "Invalid config param %04x\n", param);
return -ENOTSUPP;