orinoco: make firmware download less verbose
The firmware download code has been in a couple of releases, without any
significant issues reported in this code.
Convert to use pr_debug, so the messages can be recoverred by defining
DEBUG.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/orinoco/hermes_dld.c b/drivers/net/wireless/orinoco/hermes_dld.c
index a9ba195..a3eefe1 100644
--- a/drivers/net/wireless/orinoco/hermes_dld.c
+++ b/drivers/net/wireless/orinoco/hermes_dld.c
@@ -309,7 +309,7 @@
/* Open auxiliary port */
ret = hermes_aux_control(hw, 1);
- printk(KERN_DEBUG PFX "AUX enable returned %d\n", ret);
+ pr_debug(PFX "AUX enable returned %d\n", ret);
if (ret)
return ret;
@@ -319,12 +319,12 @@
/* Close aux port */
ret = hermes_aux_control(hw, 0);
- printk(KERN_DEBUG PFX "AUX disable returned %d\n", ret);
+ pr_debug(PFX "AUX disable returned %d\n", ret);
/* Check PDA length */
pda_size = le16_to_cpu(pda[0]);
- printk(KERN_DEBUG PFX "Actual PDA length %d, Max allowed %d\n",
- pda_size, pda_len);
+ pr_debug(PFX "Actual PDA length %d, Max allowed %d\n",
+ pda_size, pda_len);
if (pda_size > pda_len)
return -EINVAL;
@@ -422,20 +422,19 @@
return err;
err = hermes_aux_control(hw, 1);
- printk(KERN_DEBUG PFX "AUX enable returned %d\n", err);
+ pr_debug(PFX "AUX enable returned %d\n", err);
if (err)
return err;
- printk(KERN_DEBUG PFX "Enabling volatile, EP 0x%08x\n", offset);
+ pr_debug(KERN_DEBUG PFX "Enabling volatile, EP 0x%08x\n", offset);
err = hermes_doicmd_wait(hw,
HERMES_PROGRAM_ENABLE_VOLATILE,
offset & 0xFFFFu,
offset >> 16,
0,
NULL);
- printk(KERN_DEBUG PFX "PROGRAM_ENABLE returned %d\n",
- err);
+ pr_debug(PFX "PROGRAM_ENABLE returned %d\n", err);
return err;
}
@@ -454,16 +453,16 @@
rc = hermes_docmd_wait(hw, HERMES_PROGRAM_DISABLE, 0, &resp);
- printk(KERN_DEBUG PFX "PROGRAM_DISABLE returned %d, "
- "r0 0x%04x, r1 0x%04x, r2 0x%04x\n",
- rc, resp.resp0, resp.resp1, resp.resp2);
+ pr_debug(PFX "PROGRAM_DISABLE returned %d, "
+ "r0 0x%04x, r1 0x%04x, r2 0x%04x\n",
+ rc, resp.resp0, resp.resp1, resp.resp2);
if ((rc == 0) &&
((resp.status & HERMES_STATUS_CMDCODE) != HERMES_CMD_DOWNLD))
rc = -EIO;
err = hermes_aux_control(hw, 0);
- printk(KERN_DEBUG PFX "AUX disable returned %d\n", err);
+ pr_debug(PFX "AUX disable returned %d\n", err);
/* Acknowledge any outstanding command */
hermes_write_regn(hw, EVACK, 0xFFFF);
@@ -496,9 +495,8 @@
while ((blkaddr != BLOCK_END) &&
(((void *) blk + blklen) <= end)) {
- printk(KERN_DEBUG PFX
- "Programming block of length %d to address 0x%08x\n",
- blklen, blkaddr);
+ pr_debug(PFX "Programming block of length %d "
+ "to address 0x%08x\n", blklen, blkaddr);
#if !LIMIT_PROGRAM_SIZE
/* wl_lkm driver splits this into writes of 2000 bytes */
@@ -510,10 +508,9 @@
addr = blkaddr;
while (addr < (blkaddr + blklen)) {
- printk(KERN_DEBUG PFX
- "Programming subblock of length %d "
- "to address 0x%08x. Data @ %p\n",
- len, addr, &blk->data[addr - blkaddr]);
+ pr_debug(PFX "Programming subblock of length %d "
+ "to address 0x%08x. Data @ %p\n",
+ len, addr, &blk->data[addr - blkaddr]);
hermes_aux_setaddr(hw, addr);
hermes_write_bytes(hw, HERMES_AUXDATA,
@@ -643,8 +640,8 @@
pdi = hermes_find_pdi(first_pdi, record_id, pda_end);
if (pdi)
- printk(KERN_DEBUG PFX "Found record 0x%04x at %p\n",
- record_id, pdi);
+ pr_debug(PFX "Found record 0x%04x at %p\n",
+ record_id, pdi);
switch (record_id) {
case 0x110: /* Modem REFDAC values */
@@ -654,9 +651,9 @@
default_pdi = NULL;
if (outdoor_pdi) {
pdi = outdoor_pdi;
- printk(KERN_DEBUG PFX
- "Using outdoor record 0x%04x at %p\n",
- record_id + 1, pdi);
+ pr_debug(PFX
+ "Using outdoor record 0x%04x at %p\n",
+ record_id + 1, pdi);
}
break;
case 0x5: /* HWIF Compatiblity */
@@ -684,9 +681,8 @@
if (!pdi && default_pdi) {
/* Use default */
pdi = default_pdi;
- printk(KERN_DEBUG PFX
- "Using default record 0x%04x at %p\n",
- record_id, pdi);
+ pr_debug(PFX "Using default record 0x%04x at %p\n",
+ record_id, pdi);
}
if (pdi) {