MN10300: And Panasonic AM34 subarch and implement SMP
Implement the Panasonic MN10300 AM34 CPU subarch and implement SMP support for
MN10300. Also implement support for the MN2WS0060 processor and the ASB2364
evaluation board which are AM34 based.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
diff --git a/arch/mn10300/Kconfig b/arch/mn10300/Kconfig
index a0a16e6..81e2781 100644
--- a/arch/mn10300/Kconfig
+++ b/arch/mn10300/Kconfig
@@ -48,7 +48,7 @@
def_bool y
config GENERIC_CMOS_UPDATE
- def_bool y
+ def_bool n
config GENERIC_FIND_NEXT_BIT
def_bool y
@@ -72,10 +72,6 @@
config HOTPLUG_CPU
def_bool n
-config HZ
- int
- default 1000
-
mainmenu "Matsushita MN10300/AM33 Kernel Configuration"
source "init/Kconfig"
@@ -98,6 +94,9 @@
config MN10300_UNIT_ASB2305
bool "ASB2305"
+config MN10300_UNIT_ASB2364
+ bool "ASB2364"
+
endchoice
choice
@@ -115,17 +114,13 @@
select MN10300_PROC_HAS_TTYSM1
select MN10300_PROC_HAS_TTYSM2
-endchoice
-
-choice
- prompt "Processor core support"
- default MN10300_CPU_AM33V2
- help
- This option specifies the processor core for which the kernel will be
- compiled. It affects the instruction set used.
-
-config MN10300_CPU_AM33V2
- bool "AM33v2"
+config MN10300_PROC_MN2WS0050
+ bool "MN2WS0050"
+ depends on MN10300_UNIT_ASB2364
+ select AM34_2
+ select MN10300_PROC_HAS_TTYSM0
+ select MN10300_PROC_HAS_TTYSM1
+ select MN10300_PROC_HAS_TTYSM2
endchoice
@@ -138,7 +133,7 @@
config FPU
bool "FPU present"
default y
- depends on MN10300_PROC_MN103E010
+ depends on MN10300_PROC_MN103E010 || MN10300_PROC_MN2WS0050
config LAZY_SAVE_FPU
bool "Save FPU state lazily"
@@ -179,24 +174,55 @@
config KERNEL_ZIMAGE_BASE_ADDRESS
hex "Base address of compressed vmlinux image"
- default "0x90700000"
+ default "0x50700000"
+config BOOT_STACK_OFFSET
+ hex
+ default "0xF00" if SMP
+ default "0xFF0" if !SMP
+
+config BOOT_STACK_SIZE
+ hex
+ depends on SMP
+ default "0x100"
endmenu
-config PREEMPT
- bool "Preemptible Kernel"
- help
- This option reduces the latency of the kernel when reacting to
- real-time or interactive events by allowing a low priority process to
- be preempted even if it is in kernel mode executing a system call.
- This allows applications to run more reliably even when the system is
- under load.
+config SMP
+ bool "Symmetric multi-processing support"
+ default y
+ depends on MN10300_PROC_MN2WS0038 || MN10300_PROC_MN2WS0050
+ ---help---
+ This enables support for systems with more than one CPU. If you have
+ a system with only one CPU, like most personal computers, say N. If
+ you have a system with more than one CPU, say Y.
- Say Y here if you are building a kernel for a desktop, embedded
- or real-time system. Say N if you are unsure.
+ If you say N here, the kernel will run on single and multiprocessor
+ machines, but will use only one CPU of a multiprocessor machine. If
+ you say Y here, the kernel will run on many, but not all,
+ singleprocessor machines. On a singleprocessor machine, the kernel
+ will run faster if you say N here.
+
+ See also <file:Documentation/i386/IO-APIC.txt>,
+ <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
+ <http://www.tldp.org/docs.html#howto>.
+
+ If you don't know what to do here, say N.
+
+config NR_CPUS
+ int
+ depends on SMP
+ default "2"
+
+config USE_GENERIC_SMP_HELPERS
+ bool
+ depends on SMP
+ default y
+
+source "kernel/Kconfig.preempt"
config MN10300_CURRENT_IN_E2
bool "Hold current task address in E2 register"
+ depends on !SMP
default y
help
This option removes the E2/R2 register from the set available to gcc
@@ -218,12 +244,14 @@
suppresses the use of certain hardware debugging features, such as
single-stepping, which are taken over completely by the JTAG unit.
+source "kernel/Kconfig.hz"
+
config MN10300_RTC
bool "Using MN10300 RTC"
- depends on MN10300_PROC_MN103E010
+ depends on MN10300_PROC_MN103E010 || MN10300_PROC_MN2WS0050
+ select GENERIC_CMOS_UPDATE
default n
help
-
This option enables support for the RTC, thus enabling time to be
tracked, even when system is powered down. This is available on-chip
on the MN103E010.
@@ -315,14 +343,23 @@
choice
prompt "Select the timer to supply the clock for SIF1"
- default MN10300_TTYSM0_TIMER9
+ default MN10300_TTYSM1_TIMER12 \
+ if !(AM33_2 || AM33_3)
+ default MN10300_TTYSM1_TIMER9 \
+ if AM33_2 || AM33_3
depends on MN10300_TTYSM1
+config MN10300_TTYSM1_TIMER12
+ bool "Use timer 12 (16-bit)"
+ depends on !(AM33_2 || AM33_3)
+
config MN10300_TTYSM1_TIMER9
bool "Use timer 9 (16-bit)"
+ depends on AM33_2 || AM33_3
config MN10300_TTYSM1_TIMER3
bool "Use timer 3 (8-bit)"
+ depends on AM33_2 || AM33_3
endchoice
@@ -337,17 +374,33 @@
choice
prompt "Select the timer to supply the clock for SIF2"
- default MN10300_TTYSM0_TIMER10
+ default MN10300_TTYSM2_TIMER3 \
+ if !(AM33_2 || AM33_3)
+ default MN10300_TTYSM2_TIMER10 \
+ if AM33_2 || AM33_3
depends on MN10300_TTYSM2
+config MN10300_TTYSM2_TIMER9
+ bool "Use timer 9 (16-bit)"
+ depends on !(AM33_2 || AM33_3)
+
+config MN10300_TTYSM2_TIMER1
+ bool "Use timer 1 (8-bit)"
+ depends on !(AM33_2 || AM33_3)
+
+config MN10300_TTYSM2_TIMER3
+ bool "Use timer 3 (8-bit)"
+ depends on !(AM33_2 || AM33_3)
+
config MN10300_TTYSM2_TIMER10
bool "Use timer 10 (16-bit)"
+ depends on AM33_2 || AM33_3
endchoice
config MN10300_TTYSM2_CTS
bool "Enable the use of the CTS line /dev/ttySM2"
- depends on MN10300_TTYSM2
+ depends on MN10300_TTYSM2 && AM33_2
endmenu
diff --git a/arch/mn10300/Makefile b/arch/mn10300/Makefile
index ac5c6bd..7120282 100644
--- a/arch/mn10300/Makefile
+++ b/arch/mn10300/Makefile
@@ -36,6 +36,9 @@
ifeq ($(CONFIG_MN10300_PROC_MN103E010),y)
PROCESSOR := mn103e010
endif
+ifeq ($(CONFIG_MN10300_PROC_MN2WS0050),y)
+PROCESSOR := mn2ws0050
+endif
ifeq ($(CONFIG_MN10300_UNIT_ASB2303),y)
UNIT := asb2303
@@ -43,6 +46,9 @@
ifeq ($(CONFIG_MN10300_UNIT_ASB2305),y)
UNIT := asb2305
endif
+ifeq ($(CONFIG_MN10300_UNIT_ASB2364),y)
+UNIT := asb2364
+endif
head-y := arch/mn10300/kernel/head.o arch/mn10300/kernel/init_task.o
diff --git a/arch/mn10300/boot/compressed/head.S b/arch/mn10300/boot/compressed/head.S
index 4ef608a..7b50345 100644
--- a/arch/mn10300/boot/compressed/head.S
+++ b/arch/mn10300/boot/compressed/head.S
@@ -15,10 +15,28 @@
#include <linux/linkage.h>
#include <asm/cpu-regs.h>
#include <asm/cache.h>
+#ifdef CONFIG_SMP
+#include <proc/smp-regs.h>
+#endif
.globl startup_32
startup_32:
- # first save off parameters from bootloader
+#ifdef CONFIG_SMP
+ #
+ # Secondary CPUs jump directly to the kernel entry point
+ #
+ # Must save primary CPU's D0-D2 registers as they hold boot parameters
+ #
+ mov (CPUID), d3
+ and CPUID_MASK,d3
+ beq startup_primary
+ mov CONFIG_KERNEL_TEXT_ADDRESS,a0
+ jmp (a0)
+
+startup_primary:
+#endif /* CONFIG_SMP */
+
+ # first save parameters from bootloader
mov param_save_area,a0
mov d0,(a0)
mov d1,(4,a0)
diff --git a/arch/mn10300/include/asm/exceptions.h b/arch/mn10300/include/asm/exceptions.h
index 7d8080b..ca3e205 100644
--- a/arch/mn10300/include/asm/exceptions.h
+++ b/arch/mn10300/include/asm/exceptions.h
@@ -114,6 +114,8 @@
extern int die_if_no_fixup(const char *, struct pt_regs *, enum exception_code);
+#define NUM2EXCEP_IRQ_LEVEL(num) (EXCEP_IRQ_LEVEL0 + (num) * 8)
+
#endif /* __ASSEMBLY__ */
#endif /* _ASM_EXCEPTIONS_H */
diff --git a/arch/mn10300/include/asm/frame.inc b/arch/mn10300/include/asm/frame.inc
index 5b1949b..406060e 100644
--- a/arch/mn10300/include/asm/frame.inc
+++ b/arch/mn10300/include/asm/frame.inc
@@ -18,6 +18,9 @@
#ifndef __ASM_OFFSETS_H__
#include <asm/asm-offsets.h>
#endif
+#ifdef CONFIG_SMP
+#include <proc/smp-regs.h>
+#endif
#define pi break
@@ -37,9 +40,25 @@
movm [d2,d3,a2,a3,exreg0,exreg1,exother],(sp)
mov sp,fp # FRAME pointer in A3
add -12,sp # allow for calls to be made
+#ifdef CONFIG_SMP
+#ifdef CONFIG_PREEMPT /* FIXME */
+ mov epsw,d2
+ and ~EPSW_IE,epsw
+#endif
+ mov (CPUID),a0
+ add a0,a0
+ add a0,a0
+ mov (___frame,a0),a1
+ mov a1,(REG_NEXT,fp)
+ mov fp,(___frame,a0)
+#ifdef CONFIG_PREEMPT /* FIXME */
+ mov d2,epsw
+#endif
+#else /* CONFIG_SMP */
mov (__frame),a1
mov a1,(REG_NEXT,fp)
mov fp,(__frame)
+#endif /* CONFIG_SMP */
and ~EPSW_FE,epsw # disable the FPU inside the kernel
@@ -57,10 +76,27 @@
.macro RESTORE_ALL
# peel back the stack to the calling frame
# - this permits execve() to discard extra frames due to kernel syscalls
+#ifdef CONFIG_SMP
+#ifdef CONFIG_PREEMPT /* FIXME */
+ mov epsw,d2
+ and ~EPSW_IE,epsw
+#endif
+ mov (CPUID),a0
+ add a0,a0
+ add a0,a0
+ mov (___frame,a0),fp
+ mov fp,sp
+ mov (REG_NEXT,fp),d0 # userspace has regs->next == 0
+ mov d0,(___frame,a0)
+#ifdef CONFIG_PREEMPT /* FIXME */
+ mov d2,epsw
+#endif
+#else /* CONFIG_SMP */
mov (__frame),fp
mov fp,sp
mov (REG_NEXT,fp),d0 # userspace has regs->next == 0
mov d0,(__frame)
+#endif /* CONFIG_SMP */
#ifndef CONFIG_MN10300_USING_JTAG
mov (REG_EPSW,fp),d0
diff --git a/arch/mn10300/include/asm/hardirq.h b/arch/mn10300/include/asm/hardirq.h
index 7bd9b7c..0000d65 100644
--- a/arch/mn10300/include/asm/hardirq.h
+++ b/arch/mn10300/include/asm/hardirq.h
@@ -19,8 +19,10 @@
/* assembly code in softirq.h is sensitive to the offsets of these fields */
typedef struct {
unsigned int __softirq_pending;
+#ifdef CONFIG_MN10300_WD_TIMER
unsigned int __nmi_count; /* arch dependent */
unsigned int __irq_count; /* arch dependent */
+#endif
} ____cacheline_aligned irq_cpustat_t;
#include <linux/irq_cpustat.h> /* Standard mappings for irq_cpustat_t above */
diff --git a/arch/mn10300/include/asm/intctl-regs.h b/arch/mn10300/include/asm/intctl-regs.h
index ba544c7..585b708 100644
--- a/arch/mn10300/include/asm/intctl-regs.h
+++ b/arch/mn10300/include/asm/intctl-regs.h
@@ -15,24 +15,19 @@
#ifdef __KERNEL__
-/* interrupt controller registers */
-#define GxICR(X) __SYSREG(0xd4000000 + (X) * 4, u16) /* group irq ctrl regs */
+/*
+ * Interrupt controller registers
+ * - Registers 64-191 are at addresses offset from the main array
+ */
+#define GxICR(X) \
+ __SYSREG(0xd4000000 + (X) * 4 + \
+ (((X) >= 64) && ((X) < 192)) * 0xf00, u16)
-#define IAGR __SYSREG(0xd4000100, u16) /* intr acceptance group reg */
-#define IAGR_GN 0x00fc /* group number register
- * (documentation _has_ to be wrong)
- */
+#define GxICR_u8(X) \
+ __SYSREG(0xd4000000 + (X) * 4 + \
+ (((X) >= 64) && ((X) < 192)) * 0xf00, u8)
-#define EXTMD __SYSREG(0xd4000200, u16) /* external pin intr spec reg */
-#define GET_XIRQ_TRIGGER(X) ((EXTMD >> ((X) * 2)) & 3)
-
-#define SET_XIRQ_TRIGGER(X,Y) \
-do { \
- u16 x = EXTMD; \
- x &= ~(3 << ((X) * 2)); \
- x |= ((Y) & 3) << ((X) * 2); \
- EXTMD = x; \
-} while (0)
+#include <proc/intctl-regs.h>
#define XIRQ_TRIGGER_LOWLEVEL 0
#define XIRQ_TRIGGER_HILEVEL 1
@@ -59,10 +54,18 @@
#define GxICR_LEVEL_5 0x5000 /* - level 5 */
#define GxICR_LEVEL_6 0x6000 /* - level 6 */
#define GxICR_LEVEL_SHIFT 12
+#define GxICR_NMI 0x8000 /* nmi request flag */
+
+#define NUM2GxICR_LEVEL(num) ((num) << GxICR_LEVEL_SHIFT)
#ifndef __ASSEMBLY__
extern void set_intr_level(int irq, u16 level);
-extern void set_intr_postackable(int irq);
+extern void mn10300_intc_set_level(unsigned int irq, unsigned int level);
+extern void mn10300_intc_clear(unsigned int irq);
+extern void mn10300_intc_set(unsigned int irq);
+extern void mn10300_intc_enable(unsigned int irq);
+extern void mn10300_intc_disable(unsigned int irq);
+extern void mn10300_set_lateack_irq_type(int irq);
#endif
/* external interrupts */
diff --git a/arch/mn10300/include/asm/irq.h b/arch/mn10300/include/asm/irq.h
index 25c045d..b7b8e17 100644
--- a/arch/mn10300/include/asm/irq.h
+++ b/arch/mn10300/include/asm/irq.h
@@ -22,7 +22,11 @@
#define NO_IRQ INT_MAX
/* hardware irq numbers */
+#ifdef CONFIG_SMP
+#define NR_IRQS GxICR_NUM_EXT_IRQS
+#else
#define NR_IRQS GxICR_NUM_IRQS
+#endif
/* external hardware irq numbers */
#define NR_XIRQS GxICR_NUM_XIRQS
diff --git a/arch/mn10300/include/asm/irqflags.h b/arch/mn10300/include/asm/irqflags.h
index b3ab207..7a7ae12 100644
--- a/arch/mn10300/include/asm/irqflags.h
+++ b/arch/mn10300/include/asm/irqflags.h
@@ -13,6 +13,9 @@
#define _ASM_IRQFLAGS_H
#include <asm/cpu-regs.h>
+#ifndef __ASSEMBLY__
+#include <linux/smp.h>
+#endif
/*
* interrupt control
@@ -60,11 +63,12 @@
/*
* we make sure arch_irq_enable() doesn't cause priority inversion
*/
-extern unsigned long __mn10300_irq_enabled_epsw;
+extern unsigned long __mn10300_irq_enabled_epsw[];
static inline void arch_local_irq_enable(void)
{
unsigned long tmp;
+ int cpu = raw_smp_processor_id();
asm volatile(
" mov epsw,%0 \n"
@@ -72,8 +76,8 @@
" or %2,%0 \n"
" mov %0,epsw \n"
: "=&d"(tmp)
- : "i"(~EPSW_IM), "r"(__mn10300_irq_enabled_epsw)
- : "memory");
+ : "i"(~EPSW_IM), "r"(__mn10300_irq_enabled_epsw[cpu])
+ : "memory", "cc");
}
static inline void arch_local_irq_restore(unsigned long flags)
@@ -105,6 +109,9 @@
*/
static inline void arch_safe_halt(void)
{
+#ifdef CONFIG_SMP
+ arch_local_irq_enable();
+#else
asm volatile(
" or %0,epsw \n"
" nop \n"
@@ -113,8 +120,21 @@
:
: "i"(EPSW_IE|EPSW_IM), "n"(&CPUM), "i"(CPUM_SLEEP)
: "cc");
+#endif
}
+#define __sleep_cpu() \
+do { \
+ asm volatile( \
+ " bset %1,(%0)\n" \
+ "1: btst %1,(%0)\n" \
+ " bne 1b\n" \
+ : \
+ : "i"(&CPUM), "i"(CPUM_SLEEP) \
+ : "cc" \
+ ); \
+} while (0)
+
static inline void arch_local_cli(void)
{
asm volatile(
diff --git a/arch/mn10300/include/asm/pgtable.h b/arch/mn10300/include/asm/pgtable.h
index 05dda64..cd568bf 100644
--- a/arch/mn10300/include/asm/pgtable.h
+++ b/arch/mn10300/include/asm/pgtable.h
@@ -90,9 +90,15 @@
* The vmalloc() routines also leaves a hole of 4kB between each vmalloced
* area to catch addressing errors.
*/
+#ifndef __ASSEMBLY__
+#define VMALLOC_OFFSET (8UL * 1024 * 1024)
+#define VMALLOC_START (0x70000000UL)
+#define VMALLOC_END (0x7C000000UL)
+#else
#define VMALLOC_OFFSET (8 * 1024 * 1024)
#define VMALLOC_START (0x70000000)
#define VMALLOC_END (0x7C000000)
+#endif
#ifndef __ASSEMBLY__
extern pte_t kernel_vmalloc_ptes[(VMALLOC_END - VMALLOC_START) / PAGE_SIZE];
@@ -329,11 +335,7 @@
return 1;
}
-/*
- * Bits 0 and 1 are taken, split up the 29 bits of offset
- * into this range:
- */
-#define PTE_FILE_MAX_BITS 29
+#define PTE_FILE_MAX_BITS 30
#define pte_to_pgoff(pte) (pte_val(pte) >> 2)
#define pgoff_to_pte(off) __pte((off) << 2 | _PAGE_FILE)
@@ -379,8 +381,13 @@
* Macro to mark a page protection value as "uncacheable". On processors which
* do not support it, this is a no-op.
*/
-#define pgprot_noncached(prot) __pgprot(pgprot_val(prot) | _PAGE_CACHE)
+#define pgprot_noncached(prot) __pgprot(pgprot_val(prot) & ~_PAGE_CACHE)
+/*
+ * Macro to mark a page protection value as "Write-Through".
+ * On processors which do not support it, this is a no-op.
+ */
+#define pgprot_through(prot) __pgprot(pgprot_val(prot) | _PAGE_CACHE_WT)
/*
* Conversion functions: convert a page and protection to a page entry,
diff --git a/arch/mn10300/include/asm/processor.h b/arch/mn10300/include/asm/processor.h
index 0032fc7..75c422a 100644
--- a/arch/mn10300/include/asm/processor.h
+++ b/arch/mn10300/include/asm/processor.h
@@ -33,6 +33,8 @@
__pc; \
})
+extern void get_mem_info(unsigned long *mem_base, unsigned long *mem_size);
+
extern void show_registers(struct pt_regs *regs);
/*
@@ -43,17 +45,22 @@
struct mn10300_cpuinfo {
int type;
- unsigned long loops_per_sec;
+ unsigned long loops_per_jiffy;
char hard_math;
- unsigned long *pgd_quick;
- unsigned long *pte_quick;
- unsigned long pgtable_cache_sz;
};
extern struct mn10300_cpuinfo boot_cpu_data;
+#ifdef CONFIG_SMP
+#if CONFIG_NR_CPUS < 2 || CONFIG_NR_CPUS > 8
+# error Sorry, NR_CPUS should be 2 to 8
+#endif
+extern struct mn10300_cpuinfo cpu_data[];
+#define current_cpu_data cpu_data[smp_processor_id()]
+#else /* CONFIG_SMP */
#define cpu_data &boot_cpu_data
#define current_cpu_data boot_cpu_data
+#endif /* CONFIG_SMP */
extern void identify_cpu(struct mn10300_cpuinfo *);
extern void print_cpu_info(struct mn10300_cpuinfo *);
@@ -92,21 +99,21 @@
unsigned long a3; /* kernel FP */
unsigned long wchan;
unsigned long usp;
- struct pt_regs *__frame;
+ struct pt_regs *frame;
unsigned long fpu_flags;
#define THREAD_USING_FPU 0x00000001 /* T if this task is using the FPU */
#define THREAD_HAS_FPU 0x00000002 /* T if this task owns the FPU right now */
struct fpu_state_struct fpu_state;
};
-#define INIT_THREAD \
-{ \
- .uregs = init_uregs, \
- .pc = 0, \
- .sp = 0, \
- .a3 = 0, \
- .wchan = 0, \
- .__frame = NULL, \
+#define INIT_THREAD \
+{ \
+ .uregs = init_uregs, \
+ .pc = 0, \
+ .sp = 0, \
+ .a3 = 0, \
+ .wchan = 0, \
+ .frame = NULL, \
}
#define INIT_MMAP \
@@ -118,6 +125,19 @@
* - need to discard the frame stacked by the kernel thread invoking the execve
* syscall (see RESTORE_ALL macro)
*/
+#if defined(CONFIG_SMP) && defined(CONFIG_PREEMPT) /* FIXME */
+#define start_thread(regs, new_pc, new_sp) do { \
+ int cpu; \
+ preempt_disable(); \
+ cpu = CPUID; \
+ set_fs(USER_DS); \
+ ___frame[cpu] = current->thread.uregs; \
+ ___frame[cpu]->epsw = EPSW_nSL | EPSW_IE | EPSW_IM;\
+ ___frame[cpu]->pc = new_pc; \
+ ___frame[cpu]->sp = new_sp; \
+ preempt_enable(); \
+} while (0)
+#else /* CONFIG_SMP && CONFIG_PREEMPT */
#define start_thread(regs, new_pc, new_sp) do { \
set_fs(USER_DS); \
__frame = current->thread.uregs; \
@@ -125,6 +145,7 @@
__frame->pc = new_pc; \
__frame->sp = new_sp; \
} while (0)
+#endif /* CONFIG_SMP && CONFIG_PREEMPT */
/* Free all resources held by a thread. */
extern void release_thread(struct task_struct *);
diff --git a/arch/mn10300/include/asm/ptrace.h b/arch/mn10300/include/asm/ptrace.h
index 7c2e911..c2b77bd 100644
--- a/arch/mn10300/include/asm/ptrace.h
+++ b/arch/mn10300/include/asm/ptrace.h
@@ -40,7 +40,6 @@
#define PT_PC 26
#define NR_PTREGS 27
-#ifndef __ASSEMBLY__
/*
* This defines the way registers are stored in the event of an exception
* - the strange order is due to the MOVM instruction
@@ -75,7 +74,6 @@
unsigned long epsw;
unsigned long pc;
};
-#endif
/* Arbitrarily choose the same ptrace numbers as used by the Sparc code. */
#define PTRACE_GETREGS 12
@@ -86,12 +84,13 @@
/* options set using PTRACE_SETOPTIONS */
#define PTRACE_O_TRACESYSGOOD 0x00000001
-#if defined(__KERNEL__)
+#ifdef __KERNEL__
+#ifdef CONFIG_SMP
+extern struct pt_regs *___frame[]; /* current frame pointer */
+#else
extern struct pt_regs *__frame; /* current frame pointer */
-
-#if !defined(__ASSEMBLY__)
-struct task_struct;
+#endif
#define user_mode(regs) (((regs)->epsw & EPSW_nSL) == EPSW_nSL)
#define instruction_pointer(regs) ((regs)->pc)
@@ -100,9 +99,7 @@
#define arch_has_single_step() (1)
-#endif /* !__ASSEMBLY */
-
#define profile_pc(regs) ((regs)->pc)
-#endif /* __KERNEL__ */
+#endif /* __KERNEL__ */
#endif /* _ASM_PTRACE_H */
diff --git a/arch/mn10300/include/asm/reset-regs.h b/arch/mn10300/include/asm/reset-regs.h
index 174523d..10c7502 100644
--- a/arch/mn10300/include/asm/reset-regs.h
+++ b/arch/mn10300/include/asm/reset-regs.h
@@ -50,7 +50,7 @@
RSTCTR |= RSTCTR_CHIPRST;
}
-extern unsigned int watchdog_alert_counter;
+extern unsigned int watchdog_alert_counter[];
extern void watchdog_go(void);
extern asmlinkage void watchdog_handler(void);
diff --git a/arch/mn10300/include/asm/rtc.h b/arch/mn10300/include/asm/rtc.h
index c295194..6c14bb1 100644
--- a/arch/mn10300/include/asm/rtc.h
+++ b/arch/mn10300/include/asm/rtc.h
@@ -15,25 +15,14 @@
#include <linux/init.h>
-extern void check_rtc_time(void);
extern void __init calibrate_clock(void);
-extern unsigned long __init get_initial_rtc_time(void);
#else /* !CONFIG_MN10300_RTC */
-static inline void check_rtc_time(void)
-{
-}
-
static inline void calibrate_clock(void)
{
}
-static inline unsigned long get_initial_rtc_time(void)
-{
- return 0;
-}
-
#endif /* !CONFIG_MN10300_RTC */
#include <asm-generic/rtc.h>
diff --git a/arch/mn10300/include/asm/rwlock.h b/arch/mn10300/include/asm/rwlock.h
new file mode 100644
index 0000000..6d594d4
--- /dev/null
+++ b/arch/mn10300/include/asm/rwlock.h
@@ -0,0 +1,125 @@
+/*
+ * Helpers used by both rw spinlocks and rw semaphores.
+ *
+ * Based in part on code from semaphore.h and
+ * spinlock.h Copyright 1996 Linus Torvalds.
+ *
+ * Copyright 1999 Red Hat, Inc.
+ *
+ * Written by Benjamin LaHaise.
+ *
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 13-Nov-2006 MEI Temporarily delete lock functions for SMP support.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+#ifndef _ASM_RWLOCK_H
+#define _ASM_RWLOCK_H
+
+#define RW_LOCK_BIAS 0x01000000
+
+#ifndef CONFIG_SMP
+
+typedef struct { unsigned long a[100]; } __dummy_lock_t;
+#define __dummy_lock(lock) (*(__dummy_lock_t *)(lock))
+
+#define RW_LOCK_BIAS_STR "0x01000000"
+
+#define __build_read_lock_ptr(rw, helper) \
+ do { \
+ asm volatile( \
+ " mov (%0),d3 \n" \
+ " sub 1,d3 \n" \
+ " mov d3,(%0) \n" \
+ " blt 1f \n" \
+ " bra 2f \n" \
+ "1: jmp 3f \n" \
+ "2: \n" \
+ " .section .text.lock,\"ax\" \n" \
+ "3: call "helper"[],0 \n" \
+ " jmp 2b \n" \
+ " .previous" \
+ : \
+ : "d" (rw) \
+ : "memory", "d3", "cc"); \
+ } while (0)
+
+#define __build_read_lock_const(rw, helper) \
+ do { \
+ asm volatile( \
+ " mov (%0),d3 \n" \
+ " sub 1,d3 \n" \
+ " mov d3,(%0) \n" \
+ " blt 1f \n" \
+ " bra 2f \n" \
+ "1: jmp 3f \n" \
+ "2: \n" \
+ " .section .text.lock,\"ax\" \n" \
+ "3: call "helper"[],0 \n" \
+ " jmp 2b \n" \
+ " .previous" \
+ : \
+ : "d" (rw) \
+ : "memory", "d3", "cc"); \
+ } while (0)
+
+#define __build_read_lock(rw, helper) \
+ do { \
+ if (__builtin_constant_p(rw)) \
+ __build_read_lock_const(rw, helper); \
+ else \
+ __build_read_lock_ptr(rw, helper); \
+ } while (0)
+
+#define __build_write_lock_ptr(rw, helper) \
+ do { \
+ asm volatile( \
+ " mov (%0),d3 \n" \
+ " sub 1,d3 \n" \
+ " mov d3,(%0) \n" \
+ " blt 1f \n" \
+ " bra 2f \n" \
+ "1: jmp 3f \n" \
+ "2: \n" \
+ " .section .text.lock,\"ax\" \n" \
+ "3: call "helper"[],0 \n" \
+ " jmp 2b \n" \
+ " .previous" \
+ : \
+ : "d" (rw) \
+ : "memory", "d3", "cc"); \
+ } while (0)
+
+#define __build_write_lock_const(rw, helper) \
+ do { \
+ asm volatile( \
+ " mov (%0),d3 \n" \
+ " sub 1,d3 \n" \
+ " mov d3,(%0) \n" \
+ " blt 1f \n" \
+ " bra 2f \n" \
+ "1: jmp 3f \n" \
+ "2: \n" \
+ " .section .text.lock,\"ax\" \n" \
+ "3: call "helper"[],0 \n" \
+ " jmp 2b \n" \
+ " .previous" \
+ : \
+ : "d" (rw) \
+ : "memory", "d3", "cc"); \
+ } while (0)
+
+#define __build_write_lock(rw, helper) \
+ do { \
+ if (__builtin_constant_p(rw)) \
+ __build_write_lock_const(rw, helper); \
+ else \
+ __build_write_lock_ptr(rw, helper); \
+ } while (0)
+
+#endif /* CONFIG_SMP */
+#endif /* _ASM_RWLOCK_H */
diff --git a/arch/mn10300/include/asm/serial-regs.h b/arch/mn10300/include/asm/serial-regs.h
index 6498469..8320cda 100644
--- a/arch/mn10300/include/asm/serial-regs.h
+++ b/arch/mn10300/include/asm/serial-regs.h
@@ -20,18 +20,25 @@
/* serial port 0 */
#define SC0CTR __SYSREG(0xd4002000, u16) /* control reg */
#define SC01CTR_CK 0x0007 /* clock source select */
-#define SC0CTR_CK_TM8UFLOW_8 0x0000 /* - 1/8 timer 8 underflow (serial port 0 only) */
-#define SC1CTR_CK_TM9UFLOW_8 0x0000 /* - 1/8 timer 9 underflow (serial port 1 only) */
#define SC01CTR_CK_IOCLK_8 0x0001 /* - 1/8 IOCLK */
#define SC01CTR_CK_IOCLK_32 0x0002 /* - 1/32 IOCLK */
-#define SC0CTR_CK_TM2UFLOW_2 0x0003 /* - 1/2 timer 2 underflow (serial port 0 only) */
-#define SC1CTR_CK_TM3UFLOW_2 0x0003 /* - 1/2 timer 3 underflow (serial port 1 only) */
-#define SC0CTR_CK_TM0UFLOW_8 0x0004 /* - 1/8 timer 1 underflow (serial port 0 only) */
-#define SC1CTR_CK_TM1UFLOW_8 0x0004 /* - 1/8 timer 2 underflow (serial port 1 only) */
-#define SC0CTR_CK_TM2UFLOW_8 0x0005 /* - 1/8 timer 2 underflow (serial port 0 only) */
-#define SC1CTR_CK_TM3UFLOW_8 0x0005 /* - 1/8 timer 3 underflow (serial port 1 only) */
#define SC01CTR_CK_EXTERN_8 0x0006 /* - 1/8 external closk */
#define SC01CTR_CK_EXTERN 0x0007 /* - external closk */
+#if defined(CONFIG_AM33_2) || defined(CONFIG_AM33_3)
+#define SC0CTR_CK_TM8UFLOW_8 0x0000 /* - 1/8 timer 8 underflow (serial port 0 only) */
+#define SC0CTR_CK_TM2UFLOW_2 0x0003 /* - 1/2 timer 2 underflow (serial port 0 only) */
+#define SC0CTR_CK_TM0UFLOW_8 0x0004 /* - 1/8 timer 0 underflow (serial port 0 only) */
+#define SC0CTR_CK_TM2UFLOW_8 0x0005 /* - 1/8 timer 2 underflow (serial port 0 only) */
+#define SC1CTR_CK_TM9UFLOW_8 0x0000 /* - 1/8 timer 9 underflow (serial port 1 only) */
+#define SC1CTR_CK_TM3UFLOW_2 0x0003 /* - 1/2 timer 3 underflow (serial port 1 only) */
+#define SC1CTR_CK_TM1UFLOW_8 0x0004 /* - 1/8 timer 1 underflow (serial port 1 only) */
+#define SC1CTR_CK_TM3UFLOW_8 0x0005 /* - 1/8 timer 3 underflow (serial port 1 only) */
+#else /* CONFIG_AM33_2 || CONFIG_AM33_3 */
+#define SC0CTR_CK_TM8UFLOW_8 0x0000 /* - 1/8 timer 8 underflow (serial port 0 only) */
+#define SC0CTR_CK_TM0UFLOW_8 0x0004 /* - 1/8 timer 0 underflow (serial port 0 only) */
+#define SC0CTR_CK_TM2UFLOW_8 0x0005 /* - 1/8 timer 2 underflow (serial port 0 only) */
+#define SC1CTR_CK_TM12UFLOW_8 0x0000 /* - 1/8 timer 12 underflow (serial port 1 only) */
+#endif /* CONFIG_AM33_2 || CONFIG_AM33_3 */
#define SC01CTR_STB 0x0008 /* stop bit select */
#define SC01CTR_STB_1BIT 0x0000 /* - 1 stop bit */
#define SC01CTR_STB_2BIT 0x0008 /* - 2 stop bits */
@@ -100,11 +107,23 @@
/* serial port 2 */
#define SC2CTR __SYSREG(0xd4002020, u16) /* control reg */
+#ifdef CONFIG_AM33_2
#define SC2CTR_CK 0x0003 /* clock source select */
#define SC2CTR_CK_TM10UFLOW 0x0000 /* - timer 10 underflow */
#define SC2CTR_CK_TM2UFLOW 0x0001 /* - timer 2 underflow */
#define SC2CTR_CK_EXTERN 0x0002 /* - external closk */
#define SC2CTR_CK_TM3UFLOW 0x0003 /* - timer 3 underflow */
+#else /* CONFIG_AM33_2 */
+#define SC2CTR_CK 0x0007 /* clock source select */
+#define SC2CTR_CK_TM9UFLOW_8 0x0000 /* - 1/8 timer 9 underflow */
+#define SC2CTR_CK_IOCLK_8 0x0001 /* - 1/8 IOCLK */
+#define SC2CTR_CK_IOCLK_32 0x0002 /* - 1/32 IOCLK */
+#define SC2CTR_CK_TM3UFLOW_2 0x0003 /* - 1/2 timer 3 underflow */
+#define SC2CTR_CK_TM1UFLOW_8 0x0004 /* - 1/8 timer 1 underflow */
+#define SC2CTR_CK_TM3UFLOW_8 0x0005 /* - 1/8 timer 3 underflow */
+#define SC2CTR_CK_EXTERN_8 0x0006 /* - 1/8 external closk */
+#define SC2CTR_CK_EXTERN 0x0007 /* - external closk */
+#endif /* CONFIG_AM33_2 */
#define SC2CTR_STB 0x0008 /* stop bit select */
#define SC2CTR_STB_1BIT 0x0000 /* - 1 stop bit */
#define SC2CTR_STB_2BIT 0x0008 /* - 2 stop bits */
@@ -134,9 +153,14 @@
#define SC2ICR_RES 0x04 /* receive error select */
#define SC2ICR_RI 0x01 /* receive interrupt cause */
-#define SC2TXB __SYSREG(0xd4002018, u8) /* transmit buffer reg */
-#define SC2RXB __SYSREG(0xd4002019, u8) /* receive buffer reg */
-#define SC2STR __SYSREG(0xd400201c, u8) /* status reg */
+#define SC2TXB __SYSREG(0xd4002028, u8) /* transmit buffer reg */
+#define SC2RXB __SYSREG(0xd4002029, u8) /* receive buffer reg */
+
+#ifdef CONFIG_AM33_2
+#define SC2STR __SYSREG(0xd400202c, u8) /* status reg */
+#else /* CONFIG_AM33_2 */
+#define SC2STR __SYSREG(0xd400202c, u16) /* status reg */
+#endif /* CONFIG_AM33_2 */
#define SC2STR_OEF 0x0001 /* overrun error found */
#define SC2STR_PEF 0x0002 /* parity error found */
#define SC2STR_FEF 0x0004 /* framing error found */
@@ -146,10 +170,17 @@
#define SC2STR_RXF 0x0040 /* receive status */
#define SC2STR_TXF 0x0080 /* transmit status */
+#ifdef CONFIG_AM33_2
#define SC2TIM __SYSREG(0xd400202d, u8) /* status reg */
+#endif
+#ifdef CONFIG_AM33_2
#define SC2RXIRQ 24 /* serial 2 Receive IRQ */
#define SC2TXIRQ 25 /* serial 2 Transmit IRQ */
+#else /* CONFIG_AM33_2 */
+#define SC2RXIRQ 68 /* serial 2 Receive IRQ */
+#define SC2TXIRQ 69 /* serial 2 Transmit IRQ */
+#endif /* CONFIG_AM33_2 */
#define SC2RXICR GxICR(SC2RXIRQ) /* serial 2 receive intr ctrl reg */
#define SC2TXICR GxICR(SC2TXIRQ) /* serial 2 transmit intr ctrl reg */
diff --git a/arch/mn10300/include/asm/serial.h b/arch/mn10300/include/asm/serial.h
index a29445c..23a7992 100644
--- a/arch/mn10300/include/asm/serial.h
+++ b/arch/mn10300/include/asm/serial.h
@@ -9,10 +9,8 @@
* 2 of the Licence, or (at your option) any later version.
*/
-/*
- * The ASB2305 has an 18.432 MHz clock the UART
- */
-#define BASE_BAUD (18432000 / 16)
+#ifndef _ASM_SERIAL_H
+#define _ASM_SERIAL_H
/* Standard COM flags (except for COM4, because of the 8514 problem) */
#ifdef CONFIG_SERIAL_DETECT_IRQ
@@ -34,3 +32,5 @@
#endif
#include <unit/serial.h>
+
+#endif /* _ASM_SERIAL_H */
diff --git a/arch/mn10300/include/asm/smp.h b/arch/mn10300/include/asm/smp.h
index 4eb8c61..b8585b4 100644
--- a/arch/mn10300/include/asm/smp.h
+++ b/arch/mn10300/include/asm/smp.h
@@ -3,6 +3,16 @@
* Copyright (C) 2007 Red Hat, Inc. All Rights Reserved.
* Written by David Howells (dhowells@redhat.com)
*
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 13-Nov-2006 MEI Define IPI-IRQ number and add inline/macro function
+ * for SMP support.
+ * 22-Jan-2007 MEI Add the define related to SMP_BOOT_IRQ.
+ * 23-Feb-2007 MEI Add the define related to SMP icahce invalidate.
+ * 23-Jun-2008 MEI Delete INTC_IPI.
+ * 22-Jul-2008 MEI Add smp_nmi_call_function and related defines.
+ * 04-Aug-2008 MEI Delete USE_DOIRQ_CACHE_IPI.
+ *
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public Licence
* as published by the Free Software Foundation; either version
@@ -11,8 +21,98 @@
#ifndef _ASM_SMP_H
#define _ASM_SMP_H
-#ifdef CONFIG_SMP
-#error SMP not yet supported for MN10300
+#ifndef __ASSEMBLY__
+#include <linux/threads.h>
+#include <linux/cpumask.h>
#endif
+#ifdef CONFIG_SMP
+#include <proc/smp-regs.h>
+
+#define RESCHEDULE_IPI 63
+#define CALL_FUNC_SINGLE_IPI 192
+#define LOCAL_TIMER_IPI 193
+#define FLUSH_CACHE_IPI 194
+#define CALL_FUNCTION_NMI_IPI 195
+#define GDB_NMI_IPI 196
+
+#define SMP_BOOT_IRQ 195
+
+#define RESCHEDULE_GxICR_LV GxICR_LEVEL_6
+#define CALL_FUNCTION_GxICR_LV GxICR_LEVEL_4
+#define LOCAL_TIMER_GxICR_LV GxICR_LEVEL_4
+#define FLUSH_CACHE_GxICR_LV GxICR_LEVEL_0
+#define SMP_BOOT_GxICR_LV GxICR_LEVEL_0
+
+#define TIME_OUT_COUNT_BOOT_IPI 100
+#define DELAY_TIME_BOOT_IPI 75000
+
+
+#ifndef __ASSEMBLY__
+
+/**
+ * raw_smp_processor_id - Determine the raw CPU ID of the CPU running it
+ *
+ * What we really want to do is to use the CPUID hardware CPU register to get
+ * this information, but accesses to that aren't cached, and run at system bus
+ * speed, not CPU speed. A copy of this value is, however, stored in the
+ * thread_info struct, and that can be cached.
+ *
+ * An alternate way of dealing with this could be to use the EPSW.S bits to
+ * cache this information for systems with up to four CPUs.
+ */
+#if 0
+#define raw_smp_processor_id() (CPUID)
+#else
+#define raw_smp_processor_id() (current_thread_info()->cpu)
#endif
+
+static inline int cpu_logical_map(int cpu)
+{
+ return cpu;
+}
+
+static inline int cpu_number_map(int cpu)
+{
+ return cpu;
+}
+
+
+extern cpumask_t cpu_boot_map;
+
+extern void smp_init_cpus(void);
+extern void smp_cache_interrupt(void);
+extern void send_IPI_allbutself(int irq);
+extern int smp_nmi_call_function(smp_call_func_t func, void *info, int wait);
+
+extern void arch_send_call_function_single_ipi(int cpu);
+extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
+
+#ifdef CONFIG_HOTPLUG_CPU
+extern int __cpu_disable(void);
+extern void __cpu_die(unsigned int cpu);
+#endif /* CONFIG_HOTPLUG_CPU */
+
+#ifdef CONFIG_PREEMPT /* FIXME */
+#define __frame \
+ ({ \
+ struct pt_regs *f; \
+ preempt_disable(); \
+ f = ___frame[CPUID]; \
+ preempt_enable(); \
+ f; \
+ })
+#else
+#define __frame ___frame[CPUID]
+#endif
+
+#endif /* __ASSEMBLY__ */
+#else /* CONFIG_SMP */
+#ifndef __ASSEMBLY__
+
+static inline void smp_init_cpus(void) {}
+
+#endif /* __ASSEMBLY__ */
+#endif /* CONFIG_SMP */
+
+#endif /* _ASM_SMP_H */
diff --git a/arch/mn10300/include/asm/spinlock.h b/arch/mn10300/include/asm/spinlock.h
index 4bf9c8b..9342915 100644
--- a/arch/mn10300/include/asm/spinlock.h
+++ b/arch/mn10300/include/asm/spinlock.h
@@ -11,6 +11,183 @@
#ifndef _ASM_SPINLOCK_H
#define _ASM_SPINLOCK_H
-#error SMP spinlocks not implemented for MN10300
+#include <asm/atomic.h>
+#include <asm/rwlock.h>
+#include <asm/page.h>
+/*
+ * Simple spin lock operations. There are two variants, one clears IRQ's
+ * on the local processor, one does not.
+ *
+ * We make no fairness assumptions. They have a cost.
+ */
+
+#define arch_spin_is_locked(x) (*(volatile signed char *)(&(x)->slock) != 0)
+#define arch_spin_unlock_wait(x) do { barrier(); } while (arch_spin_is_locked(x))
+
+static inline void arch_spin_unlock(arch_spinlock_t *lock)
+{
+ asm volatile(
+ " bclr 1,(0,%0) \n"
+ :
+ : "a"(&lock->slock)
+ : "memory", "cc");
+}
+
+static inline int arch_spin_trylock(arch_spinlock_t *lock)
+{
+ int ret;
+
+ asm volatile(
+ " mov 1,%0 \n"
+ " bset %0,(%1) \n"
+ " bne 1f \n"
+ " clr %0 \n"
+ "1: xor 1,%0 \n"
+ : "=d"(ret)
+ : "a"(&lock->slock)
+ : "memory", "cc");
+
+ return ret;
+}
+
+static inline void arch_spin_lock(arch_spinlock_t *lock)
+{
+ asm volatile(
+ "1: bset 1,(0,%0) \n"
+ " bne 1b \n"
+ :
+ : "a"(&lock->slock)
+ : "memory", "cc");
+}
+
+static inline void arch_spin_lock_flags(arch_spinlock_t *lock,
+ unsigned long flags)
+{
+ int temp;
+
+ asm volatile(
+ "1: bset 1,(0,%2) \n"
+ " beq 3f \n"
+ " mov %1,epsw \n"
+ "2: mov (0,%2),%0 \n"
+ " or %0,%0 \n"
+ " bne 2b \n"
+ " mov %3,%0 \n"
+ " mov %0,epsw \n"
+ " nop \n"
+ " nop \n"
+ " bra 1b\n"
+ "3: \n"
+ : "=&d" (temp)
+ : "d" (flags), "a"(&lock->slock), "i"(EPSW_IE | MN10300_CLI_LEVEL)
+ : "memory", "cc");
+}
+
+#ifdef __KERNEL__
+
+/*
+ * Read-write spinlocks, allowing multiple readers
+ * but only one writer.
+ *
+ * NOTE! it is quite common to have readers in interrupts
+ * but no interrupt writers. For those circumstances we
+ * can "mix" irq-safe locks - any writer needs to get a
+ * irq-safe write-lock, but readers can get non-irqsafe
+ * read-locks.
+ */
+
+/**
+ * read_can_lock - would read_trylock() succeed?
+ * @lock: the rwlock in question.
+ */
+#define arch_read_can_lock(x) ((int)(x)->lock > 0)
+
+/**
+ * write_can_lock - would write_trylock() succeed?
+ * @lock: the rwlock in question.
+ */
+#define arch_write_can_lock(x) ((x)->lock == RW_LOCK_BIAS)
+
+/*
+ * On mn10300, we implement read-write locks as a 32-bit counter
+ * with the high bit (sign) being the "contended" bit.
+ */
+static inline void arch_read_lock(arch_rwlock_t *rw)
+{
+#if 0 //def CONFIG_MN10300_HAS_ATOMIC_OPS_UNIT
+ __build_read_lock(rw, "__read_lock_failed");
+#else
+ {
+ atomic_t *count = (atomic_t *)rw;
+ while (atomic_dec_return(count) < 0)
+ atomic_inc(count);
+ }
+#endif
+}
+
+static inline void arch_write_lock(arch_rwlock_t *rw)
+{
+#if 0 //def CONFIG_MN10300_HAS_ATOMIC_OPS_UNIT
+ __build_write_lock(rw, "__write_lock_failed");
+#else
+ {
+ atomic_t *count = (atomic_t *)rw;
+ while (!atomic_sub_and_test(RW_LOCK_BIAS, count))
+ atomic_add(RW_LOCK_BIAS, count);
+ }
+#endif
+}
+
+static inline void arch_read_unlock(arch_rwlock_t *rw)
+{
+#if 0 //def CONFIG_MN10300_HAS_ATOMIC_OPS_UNIT
+ __build_read_unlock(rw);
+#else
+ {
+ atomic_t *count = (atomic_t *)rw;
+ atomic_inc(count);
+ }
+#endif
+}
+
+static inline void arch_write_unlock(arch_rwlock_t *rw)
+{
+#if 0 //def CONFIG_MN10300_HAS_ATOMIC_OPS_UNIT
+ __build_write_unlock(rw);
+#else
+ {
+ atomic_t *count = (atomic_t *)rw;
+ atomic_add(RW_LOCK_BIAS, count);
+ }
+#endif
+}
+
+static inline int arch_read_trylock(arch_rwlock_t *lock)
+{
+ atomic_t *count = (atomic_t *)lock;
+ atomic_dec(count);
+ if (atomic_read(count) >= 0)
+ return 1;
+ atomic_inc(count);
+ return 0;
+}
+
+static inline int arch_write_trylock(arch_rwlock_t *lock)
+{
+ atomic_t *count = (atomic_t *)lock;
+ if (atomic_sub_and_test(RW_LOCK_BIAS, count))
+ return 1;
+ atomic_add(RW_LOCK_BIAS, count);
+ return 0;
+}
+
+#define arch_read_lock_flags(lock, flags) arch_read_lock(lock)
+#define arch_write_lock_flags(lock, flags) arch_write_lock(lock)
+
+#define _raw_spin_relax(lock) cpu_relax()
+#define _raw_read_relax(lock) cpu_relax()
+#define _raw_write_relax(lock) cpu_relax()
+
+#endif /* __KERNEL__ */
#endif /* _ASM_SPINLOCK_H */
diff --git a/arch/mn10300/include/asm/spinlock_types.h b/arch/mn10300/include/asm/spinlock_types.h
new file mode 100644
index 0000000..653dc51
--- /dev/null
+++ b/arch/mn10300/include/asm/spinlock_types.h
@@ -0,0 +1,20 @@
+#ifndef _ASM_SPINLOCK_TYPES_H
+#define _ASM_SPINLOCK_TYPES_H
+
+#ifndef __LINUX_SPINLOCK_TYPES_H
+# error "please don't include this file directly"
+#endif
+
+typedef struct arch_spinlock {
+ unsigned int slock;
+} arch_spinlock_t;
+
+#define __ARCH_SPIN_LOCK_UNLOCKED { 0 }
+
+typedef struct {
+ unsigned int lock;
+} arch_rwlock_t;
+
+#define __ARCH_RW_LOCK_UNLOCKED { RW_LOCK_BIAS }
+
+#endif /* _ASM_SPINLOCK_TYPES_H */
diff --git a/arch/mn10300/include/asm/system.h b/arch/mn10300/include/asm/system.h
index 7de90bc..8ff3e5a 100644
--- a/arch/mn10300/include/asm/system.h
+++ b/arch/mn10300/include/asm/system.h
@@ -12,6 +12,7 @@
#define _ASM_SYSTEM_H
#include <asm/cpu-regs.h>
+#include <asm/intctl-regs.h>
#ifdef __KERNEL__
#ifndef __ASSEMBLY__
@@ -57,8 +58,6 @@
#define nop() asm volatile ("nop")
-#endif /* !__ASSEMBLY__ */
-
/*
* Force strict CPU ordering.
* And yes, this is required on UP too when we're talking
@@ -85,17 +84,19 @@
#define smp_mb() mb()
#define smp_rmb() rmb()
#define smp_wmb() wmb()
-#else
+#define set_mb(var, value) do { xchg(&var, value); } while (0)
+#else /* CONFIG_SMP */
#define smp_mb() barrier()
#define smp_rmb() barrier()
#define smp_wmb() barrier()
-#endif
-
#define set_mb(var, value) do { var = value; mb(); } while (0)
+#endif /* CONFIG_SMP */
+
#define set_wmb(var, value) do { var = value; wmb(); } while (0)
#define read_barrier_depends() do {} while (0)
#define smp_read_barrier_depends() do {} while (0)
+#endif /* !__ASSEMBLY__ */
#endif /* __KERNEL__ */
#endif /* _ASM_SYSTEM_H */
diff --git a/arch/mn10300/include/asm/timer-regs.h b/arch/mn10300/include/asm/timer-regs.h
index 1d883b7..c634977 100644
--- a/arch/mn10300/include/asm/timer-regs.h
+++ b/arch/mn10300/include/asm/timer-regs.h
@@ -17,21 +17,27 @@
#ifdef __KERNEL__
-/* timer prescalar control */
+/*
+ * Timer prescalar control
+ */
#define TMPSCNT __SYSREG(0xd4003071, u8) /* timer prescaler control */
#define TMPSCNT_ENABLE 0x80 /* timer prescaler enable */
#define TMPSCNT_DISABLE 0x00 /* timer prescaler disable */
-/* 8 bit timers */
+/*
+ * 8-bit timers
+ */
#define TM0MD __SYSREG(0xd4003000, u8) /* timer 0 mode register */
#define TM0MD_SRC 0x07 /* timer source */
#define TM0MD_SRC_IOCLK 0x00 /* - IOCLK */
#define TM0MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
#define TM0MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
-#define TM0MD_SRC_TM2IO 0x03 /* - TM2IO pin input */
#define TM0MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM0MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
+#define TM0MD_SRC_TM2IO 0x03 /* - TM2IO pin input */
#define TM0MD_SRC_TM0IO 0x07 /* - TM0IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM0MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM0MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -43,7 +49,9 @@
#define TM1MD_SRC_TM0CASCADE 0x03 /* - cascade with timer 0 */
#define TM1MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM1MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM1MD_SRC_TM1IO 0x07 /* - TM1IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM1MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM1MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -55,7 +63,9 @@
#define TM2MD_SRC_TM1CASCADE 0x03 /* - cascade with timer 1 */
#define TM2MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM2MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
+#if defined(CONFIG_AM33_2)
#define TM2MD_SRC_TM2IO 0x07 /* - TM2IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM2MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM2MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -64,11 +74,13 @@
#define TM3MD_SRC_IOCLK 0x00 /* - IOCLK */
#define TM3MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
#define TM3MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
-#define TM3MD_SRC_TM1CASCADE 0x03 /* - cascade with timer 2 */
+#define TM3MD_SRC_TM2CASCADE 0x03 /* - cascade with timer 2 */
#define TM3MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM3MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM3MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM3MD_SRC_TM3IO 0x07 /* - TM3IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM3MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM3MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -96,7 +108,9 @@
#define TM2ICR GxICR(TM2IRQ) /* timer 2 uflow intr ctrl reg */
#define TM3ICR GxICR(TM3IRQ) /* timer 3 uflow intr ctrl reg */
-/* 16-bit timers 4,5 & 7-11 */
+/*
+ * 16-bit timers 4,5 & 7-15
+ */
#define TM4MD __SYSREG(0xd4003080, u8) /* timer 4 mode register */
#define TM4MD_SRC 0x07 /* timer source */
#define TM4MD_SRC_IOCLK 0x00 /* - IOCLK */
@@ -105,7 +119,9 @@
#define TM4MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM4MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM4MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM4MD_SRC_TM4IO 0x07 /* - TM4IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM4MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM4MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -118,7 +134,11 @@
#define TM5MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM5MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM5MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM5MD_SRC_TM5IO 0x07 /* - TM5IO pin input */
+#else /* !CONFIG_AM33_2 */
+#define TM5MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#endif /* CONFIG_AM33_2 */
#define TM5MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM5MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -130,7 +150,9 @@
#define TM7MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM7MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM7MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM7MD_SRC_TM7IO 0x07 /* - TM7IO pin input */
+#endif /* CONFIG_AM33_2 */
#define TM7MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM7MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -143,7 +165,11 @@
#define TM8MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM8MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM8MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM8MD_SRC_TM8IO 0x07 /* - TM8IO pin input */
+#else /* !CONFIG_AM33_2 */
+#define TM8MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#endif /* CONFIG_AM33_2 */
#define TM8MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM8MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -156,7 +182,11 @@
#define TM9MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM9MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM9MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM9MD_SRC_TM9IO 0x07 /* - TM9IO pin input */
+#else /* !CONFIG_AM33_2 */
+#define TM9MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#endif /* CONFIG_AM33_2 */
#define TM9MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM9MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -169,7 +199,11 @@
#define TM10MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM10MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM10MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM10MD_SRC_TM10IO 0x07 /* - TM10IO pin input */
+#else /* !CONFIG_AM33_2 */
+#define TM10MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#endif /* CONFIG_AM33_2 */
#define TM10MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM10MD_COUNT_ENABLE 0x80 /* timer count enable */
@@ -178,32 +212,101 @@
#define TM11MD_SRC_IOCLK 0x00 /* - IOCLK */
#define TM11MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
#define TM11MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
-#define TM11MD_SRC_TM7CASCADE 0x03 /* - cascade with timer 7 */
#define TM11MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
#define TM11MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
#define TM11MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
#define TM11MD_SRC_TM11IO 0x07 /* - TM11IO pin input */
+#else /* !CONFIG_AM33_2 */
+#define TM11MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#endif /* CONFIG_AM33_2 */
#define TM11MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
#define TM11MD_COUNT_ENABLE 0x80 /* timer count enable */
+#if defined(CONFIG_AM34_2)
+#define TM12MD __SYSREG(0xd4003180, u8) /* timer 11 mode register */
+#define TM12MD_SRC 0x07 /* timer source */
+#define TM12MD_SRC_IOCLK 0x00 /* - IOCLK */
+#define TM12MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
+#define TM12MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
+#define TM12MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
+#define TM12MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
+#define TM12MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#define TM12MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#define TM12MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
+#define TM12MD_COUNT_ENABLE 0x80 /* timer count enable */
+
+#define TM13MD __SYSREG(0xd4003182, u8) /* timer 11 mode register */
+#define TM13MD_SRC 0x07 /* timer source */
+#define TM13MD_SRC_IOCLK 0x00 /* - IOCLK */
+#define TM13MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
+#define TM13MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
+#define TM13MD_SRC_TM12CASCADE 0x03 /* - cascade with timer 12 */
+#define TM13MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
+#define TM13MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
+#define TM13MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#define TM13MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#define TM13MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
+#define TM13MD_COUNT_ENABLE 0x80 /* timer count enable */
+
+#define TM14MD __SYSREG(0xd4003184, u8) /* timer 11 mode register */
+#define TM14MD_SRC 0x07 /* timer source */
+#define TM14MD_SRC_IOCLK 0x00 /* - IOCLK */
+#define TM14MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
+#define TM14MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
+#define TM14MD_SRC_TM13CASCADE 0x03 /* - cascade with timer 13 */
+#define TM14MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
+#define TM14MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
+#define TM14MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#define TM14MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#define TM14MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
+#define TM14MD_COUNT_ENABLE 0x80 /* timer count enable */
+
+#define TM15MD __SYSREG(0xd4003186, u8) /* timer 11 mode register */
+#define TM15MD_SRC 0x07 /* timer source */
+#define TM15MD_SRC_IOCLK 0x00 /* - IOCLK */
+#define TM15MD_SRC_IOCLK_8 0x01 /* - 1/8 IOCLK */
+#define TM15MD_SRC_IOCLK_32 0x02 /* - 1/32 IOCLK */
+#define TM15MD_SRC_TM0UFLOW 0x04 /* - timer 0 underflow */
+#define TM15MD_SRC_TM1UFLOW 0x05 /* - timer 1 underflow */
+#define TM15MD_SRC_TM2UFLOW 0x06 /* - timer 2 underflow */
+#define TM15MD_SRC_TM7UFLOW 0x07 /* - timer 7 underflow */
+#define TM15MD_INIT_COUNTER 0x40 /* initialize TMnBC = TMnBR */
+#define TM15MD_COUNT_ENABLE 0x80 /* timer count enable */
+#endif /* CONFIG_AM34_2 */
+
+
#define TM4BR __SYSREG(0xd4003090, u16) /* timer 4 base register */
#define TM5BR __SYSREG(0xd4003092, u16) /* timer 5 base register */
+#define TM45BR __SYSREG(0xd4003090, u32) /* timer 4:5 base register */
#define TM7BR __SYSREG(0xd4003096, u16) /* timer 7 base register */
#define TM8BR __SYSREG(0xd4003098, u16) /* timer 8 base register */
#define TM9BR __SYSREG(0xd400309a, u16) /* timer 9 base register */
+#define TM89BR __SYSREG(0xd4003098, u32) /* timer 8:9 base register */
#define TM10BR __SYSREG(0xd400309c, u16) /* timer 10 base register */
#define TM11BR __SYSREG(0xd400309e, u16) /* timer 11 base register */
-#define TM45BR __SYSREG(0xd4003090, u32) /* timer 4:5 base register */
+#if defined(CONFIG_AM34_2)
+#define TM12BR __SYSREG(0xd4003190, u16) /* timer 12 base register */
+#define TM13BR __SYSREG(0xd4003192, u16) /* timer 13 base register */
+#define TM14BR __SYSREG(0xd4003194, u16) /* timer 14 base register */
+#define TM15BR __SYSREG(0xd4003196, u16) /* timer 15 base register */
+#endif /* CONFIG_AM34_2 */
#define TM4BC __SYSREG(0xd40030a0, u16) /* timer 4 binary counter */
#define TM5BC __SYSREG(0xd40030a2, u16) /* timer 5 binary counter */
#define TM45BC __SYSREG(0xd40030a0, u32) /* timer 4:5 binary counter */
-
#define TM7BC __SYSREG(0xd40030a6, u16) /* timer 7 binary counter */
#define TM8BC __SYSREG(0xd40030a8, u16) /* timer 8 binary counter */
#define TM9BC __SYSREG(0xd40030aa, u16) /* timer 9 binary counter */
+#define TM89BC __SYSREG(0xd40030a8, u32) /* timer 8:9 binary counter */
#define TM10BC __SYSREG(0xd40030ac, u16) /* timer 10 binary counter */
#define TM11BC __SYSREG(0xd40030ae, u16) /* timer 11 binary counter */
+#if defined(CONFIG_AM34_2)
+#define TM12BC __SYSREG(0xd40031a0, u16) /* timer 12 binary counter */
+#define TM13BC __SYSREG(0xd40031a2, u16) /* timer 13 binary counter */
+#define TM14BC __SYSREG(0xd40031a4, u16) /* timer 14 binary counter */
+#define TM15BC __SYSREG(0xd40031a6, u16) /* timer 15 binary counter */
+#endif /* CONFIG_AM34_2 */
#define TM4IRQ 6 /* timer 4 IRQ */
#define TM5IRQ 7 /* timer 5 IRQ */
@@ -212,6 +315,12 @@
#define TM9IRQ 13 /* timer 9 IRQ */
#define TM10IRQ 14 /* timer 10 IRQ */
#define TM11IRQ 15 /* timer 11 IRQ */
+#if defined(CONFIG_AM34_2)
+#define TM12IRQ 64 /* timer 12 IRQ */
+#define TM13IRQ 65 /* timer 13 IRQ */
+#define TM14IRQ 66 /* timer 14 IRQ */
+#define TM15IRQ 67 /* timer 15 IRQ */
+#endif /* CONFIG_AM34_2 */
#define TM4ICR GxICR(TM4IRQ) /* timer 4 uflow intr ctrl reg */
#define TM5ICR GxICR(TM5IRQ) /* timer 5 uflow intr ctrl reg */
@@ -220,8 +329,16 @@
#define TM9ICR GxICR(TM9IRQ) /* timer 9 uflow intr ctrl reg */
#define TM10ICR GxICR(TM10IRQ) /* timer 10 uflow intr ctrl reg */
#define TM11ICR GxICR(TM11IRQ) /* timer 11 uflow intr ctrl reg */
+#if defined(CONFIG_AM34_2)
+#define TM12ICR GxICR(TM12IRQ) /* timer 12 uflow intr ctrl reg */
+#define TM13ICR GxICR(TM13IRQ) /* timer 13 uflow intr ctrl reg */
+#define TM14ICR GxICR(TM14IRQ) /* timer 14 uflow intr ctrl reg */
+#define TM15ICR GxICR(TM15IRQ) /* timer 15 uflow intr ctrl reg */
+#endif /* CONFIG_AM34_2 */
-/* 16-bit timer 6 */
+/*
+ * 16-bit timer 6
+ */
#define TM6MD __SYSREG(0xd4003084, u16) /* timer6 mode register */
#define TM6MD_SRC 0x0007 /* timer source */
#define TM6MD_SRC_IOCLK 0x0000 /* - IOCLK */
@@ -229,10 +346,14 @@
#define TM6MD_SRC_IOCLK_32 0x0002 /* - 1/32 IOCLK */
#define TM6MD_SRC_TM0UFLOW 0x0004 /* - timer 0 underflow */
#define TM6MD_SRC_TM1UFLOW 0x0005 /* - timer 1 underflow */
-#define TM6MD_SRC_TM6IOB_BOTH 0x0006 /* - TM6IOB pin input (both edges) */
+#define TM6MD_SRC_TM2UFLOW 0x0006 /* - timer 2 underflow */
+#if defined(CONFIG_AM33_2)
+/* #define TM6MD_SRC_TM6IOB_BOTH 0x0006 */ /* - TM6IOB pin input (both edges) */
#define TM6MD_SRC_TM6IOB_SINGLE 0x0007 /* - TM6IOB pin input (single edge) */
-#define TM6MD_CLR_ENABLE 0x0010 /* clear count enable */
+#endif /* CONFIG_AM33_2 */
#define TM6MD_ONESHOT_ENABLE 0x0040 /* oneshot count */
+#define TM6MD_CLR_ENABLE 0x0010 /* clear count enable */
+#if defined(CONFIG_AM33_2)
#define TM6MD_TRIG_ENABLE 0x0080 /* TM6IOB pin trigger enable */
#define TM6MD_PWM 0x3800 /* PWM output mode */
#define TM6MD_PWM_DIS 0x0000 /* - disabled */
@@ -240,10 +361,15 @@
#define TM6MD_PWM_11BIT 0x1800 /* - 11 bits mode */
#define TM6MD_PWM_12BIT 0x3000 /* - 12 bits mode */
#define TM6MD_PWM_14BIT 0x3800 /* - 14 bits mode */
+#endif /* CONFIG_AM33_2 */
+
#define TM6MD_INIT_COUNTER 0x4000 /* initialize TMnBC to zero */
#define TM6MD_COUNT_ENABLE 0x8000 /* timer count enable */
#define TM6MDA __SYSREG(0xd40030b4, u8) /* timer6 cmp/cap A mode reg */
+#define TM6MDA_MODE_CMP_SINGLE 0x00 /* - compare, single buffer mode */
+#define TM6MDA_MODE_CMP_DOUBLE 0x40 /* - compare, double buffer mode */
+#if defined(CONFIG_AM33_2)
#define TM6MDA_OUT 0x07 /* output select */
#define TM6MDA_OUT_SETA_RESETB 0x00 /* - set at match A, reset at match B */
#define TM6MDA_OUT_SETA_RESETOV 0x01 /* - set at match A, reset at overflow */
@@ -251,30 +377,35 @@
#define TM6MDA_OUT_RESETA 0x03 /* - reset at match A */
#define TM6MDA_OUT_TOGGLE 0x04 /* - toggle on match A */
#define TM6MDA_MODE 0xc0 /* compare A register mode */
-#define TM6MDA_MODE_CMP_SINGLE 0x00 /* - compare, single buffer mode */
-#define TM6MDA_MODE_CMP_DOUBLE 0x40 /* - compare, double buffer mode */
#define TM6MDA_MODE_CAP_S_EDGE 0x80 /* - capture, single edge mode */
#define TM6MDA_MODE_CAP_D_EDGE 0xc0 /* - capture, double edge mode */
#define TM6MDA_EDGE 0x20 /* compare A edge select */
#define TM6MDA_EDGE_FALLING 0x00 /* capture on falling edge */
#define TM6MDA_EDGE_RISING 0x20 /* capture on rising edge */
#define TM6MDA_CAPTURE_ENABLE 0x10 /* capture enable */
+#else /* !CONFIG_AM33_2 */
+#define TM6MDA_MODE 0x40 /* compare A register mode */
+#endif /* CONFIG_AM33_2 */
#define TM6MDB __SYSREG(0xd40030b5, u8) /* timer6 cmp/cap B mode reg */
+#define TM6MDB_MODE_CMP_SINGLE 0x00 /* - compare, single buffer mode */
+#define TM6MDB_MODE_CMP_DOUBLE 0x40 /* - compare, double buffer mode */
+#if defined(CONFIG_AM33_2)
#define TM6MDB_OUT 0x07 /* output select */
#define TM6MDB_OUT_SETB_RESETA 0x00 /* - set at match B, reset at match A */
#define TM6MDB_OUT_SETB_RESETOV 0x01 /* - set at match B */
#define TM6MDB_OUT_RESETB 0x03 /* - reset at match B */
#define TM6MDB_OUT_TOGGLE 0x04 /* - toggle on match B */
#define TM6MDB_MODE 0xc0 /* compare B register mode */
-#define TM6MDB_MODE_CMP_SINGLE 0x00 /* - compare, single buffer mode */
-#define TM6MDB_MODE_CMP_DOUBLE 0x40 /* - compare, double buffer mode */
#define TM6MDB_MODE_CAP_S_EDGE 0x80 /* - capture, single edge mode */
#define TM6MDB_MODE_CAP_D_EDGE 0xc0 /* - capture, double edge mode */
#define TM6MDB_EDGE 0x20 /* compare B edge select */
#define TM6MDB_EDGE_FALLING 0x00 /* capture on falling edge */
#define TM6MDB_EDGE_RISING 0x20 /* capture on rising edge */
#define TM6MDB_CAPTURE_ENABLE 0x10 /* capture enable */
+#else /* !CONFIG_AM33_2 */
+#define TM6MDB_MODE 0x40 /* compare B register mode */
+#endif /* CONFIG_AM33_2 */
#define TM6CA __SYSREG(0xd40030c4, u16) /* timer6 cmp/capture reg A */
#define TM6CB __SYSREG(0xd40030d4, u16) /* timer6 cmp/capture reg B */
@@ -288,6 +419,34 @@
#define TM6AICR GxICR(TM6AIRQ) /* timer 6A intr control reg */
#define TM6BICR GxICR(TM6BIRQ) /* timer 6B intr control reg */
+#if defined(CONFIG_AM34_2)
+/*
+ * MTM: OS Tick-Timer
+ */
+#define TMTMD __SYSREG(0xd4004100, u8) /* Tick Timer mode register */
+#define TMTMD_TMTLDE 0x40 /* initialize TMTBC = TMTBR */
+#define TMTMD_TMTCNE 0x80 /* timer count enable */
+
+#define TMTBR __SYSREG(0xd4004110, u32) /* Tick Timer mode reg */
+#define TMTBC __SYSREG(0xd4004120, u32) /* Tick Timer mode reg */
+
+/*
+ * MTM: OS Timestamp-Timer
+ */
+#define TMSMD __SYSREG(0xd4004140, u8) /* Tick Timer mode register */
+#define TMSMD_TMSLDE 0x40 /* initialize TMSBC = TMSBR */
+#define TMSMD_TMSCNE 0x80 /* timer count enable */
+
+#define TMSBR __SYSREG(0xd4004150, u32) /* Tick Timer mode register */
+#define TMSBC __SYSREG(0xd4004160, u32) /* Tick Timer mode register */
+
+#define TMTIRQ 119 /* OS Tick timer IRQ */
+#define TMSIRQ 120 /* Timestamp timer IRQ */
+
+#define TMTICR GxICR(TMTIRQ) /* OS Tick timer uflow intr ctrl reg */
+#define TMSICR GxICR(TMSIRQ) /* Timestamp timer uflow intr ctrl reg */
+#endif /* CONFIG_AM34_2 */
+
#endif /* __KERNEL__ */
#endif /* _ASM_TIMER_REGS_H */
diff --git a/arch/mn10300/include/asm/timex.h b/arch/mn10300/include/asm/timex.h
index 8d031f9..ce5719a 100644
--- a/arch/mn10300/include/asm/timex.h
+++ b/arch/mn10300/include/asm/timex.h
@@ -16,8 +16,7 @@
#define TICK_SIZE (tick_nsec / 1000)
-#define CLOCK_TICK_RATE 1193180 /* Underlying HZ - this should probably be set
- * to something appropriate, but what? */
+#define CLOCK_TICK_RATE MN10300_JCCLK /* Underlying HZ */
extern cycles_t cacheflush_time;
diff --git a/arch/mn10300/include/asm/uaccess.h b/arch/mn10300/include/asm/uaccess.h
index 197a7af..47e7951 100644
--- a/arch/mn10300/include/asm/uaccess.h
+++ b/arch/mn10300/include/asm/uaccess.h
@@ -377,7 +377,7 @@
#if 0
-#error don't use - these macros don't increment to & from pointers
+#error "don't use - these macros don't increment to & from pointers"
/* Optimize just a little bit when we know the size of the move. */
#define __constant_copy_user(to, from, size) \
do { \
diff --git a/arch/mn10300/kernel/Makefile b/arch/mn10300/kernel/Makefile
index 9902235..5b41192 100644
--- a/arch/mn10300/kernel/Makefile
+++ b/arch/mn10300/kernel/Makefile
@@ -10,8 +10,9 @@
ptrace.o setup.o time.o sys_mn10300.o io.o kthread.o \
switch_to.o mn10300_ksyms.o kernel_execve.o $(fpu-obj-y)
-obj-$(CONFIG_MN10300_WD_TIMER) += mn10300-watchdog.o mn10300-watchdog-low.o
+obj-$(CONFIG_SMP) += smp.o smp-low.o
+obj-$(CONFIG_MN10300_WD_TIMER) += mn10300-watchdog.o mn10300-watchdog-low.o
obj-$(CONFIG_MN10300_TTYSM) += mn10300-serial.o mn10300-serial-low.o \
mn10300-debug.o
diff --git a/arch/mn10300/kernel/asm-offsets.c b/arch/mn10300/kernel/asm-offsets.c
index 78e290e..54cc5b6 100644
--- a/arch/mn10300/kernel/asm-offsets.c
+++ b/arch/mn10300/kernel/asm-offsets.c
@@ -66,7 +66,7 @@
OFFSET(THREAD_SP, thread_struct, sp);
OFFSET(THREAD_A3, thread_struct, a3);
OFFSET(THREAD_USP, thread_struct, usp);
- OFFSET(THREAD_FRAME, thread_struct, __frame);
+ OFFSET(THREAD_FRAME, thread_struct, frame);
#ifdef CONFIG_FPU
OFFSET(THREAD_FPU_FLAGS, thread_struct, fpu_flags);
OFFSET(THREAD_FPU_STATE, thread_struct, fpu_state);
diff --git a/arch/mn10300/kernel/entry.S b/arch/mn10300/kernel/entry.S
index 355f681..f00b9baf 100644
--- a/arch/mn10300/kernel/entry.S
+++ b/arch/mn10300/kernel/entry.S
@@ -28,25 +28,17 @@
#include <asm/asm-offsets.h>
#include <asm/frame.inc>
+#if defined(CONFIG_SMP) && defined(CONFIG_GDBSTUB)
+#include <asm/gdb-stub.h>
+#endif /* CONFIG_SMP && CONFIG_GDBSTUB */
+
#ifdef CONFIG_PREEMPT
-#define preempt_stop __cli
+#define preempt_stop LOCAL_IRQ_DISABLE
#else
#define preempt_stop
#define resume_kernel restore_all
#endif
- .macro __cli
- and ~EPSW_IM,epsw
- or EPSW_IE|MN10300_CLI_LEVEL,epsw
- nop
- nop
- nop
- .endm
- .macro __sti
- or EPSW_IE|EPSW_IM_7,epsw
- .endm
-
-
.am33_2
###############################################################################
@@ -88,7 +80,7 @@
syscall_exit:
# make sure we don't miss an interrupt setting need_resched or
# sigpending between sampling and the rti
- __cli
+ LOCAL_IRQ_DISABLE
mov (TI_flags,a2),d2
btst _TIF_ALLWORK_MASK,d2
bne syscall_exit_work
@@ -105,7 +97,7 @@
syscall_exit_work:
btst _TIF_SYSCALL_TRACE,d2
beq work_pending
- __sti # could let syscall_trace_exit() call
+ LOCAL_IRQ_ENABLE # could let syscall_trace_exit() call
# schedule() instead
mov fp,d0
call syscall_trace_exit[],0 # do_syscall_trace(regs)
@@ -121,7 +113,7 @@
# make sure we don't miss an interrupt setting need_resched or
# sigpending between sampling and the rti
- __cli
+ LOCAL_IRQ_DISABLE
# is there any work to be done other than syscall tracing?
mov (TI_flags,a2),d2
@@ -168,7 +160,7 @@
ENTRY(resume_userspace)
# make sure we don't miss an interrupt setting need_resched or
# sigpending between sampling and the rti
- __cli
+ LOCAL_IRQ_DISABLE
# is there any work to be done on int/exception return?
mov (TI_flags,a2),d2
@@ -178,7 +170,7 @@
#ifdef CONFIG_PREEMPT
ENTRY(resume_kernel)
- __cli
+ LOCAL_IRQ_DISABLE
mov (TI_preempt_count,a2),d0 # non-zero preempt_count ?
cmp 0,d0
bne restore_all
@@ -281,6 +273,79 @@
add -4,sp
mov d0,(sp)
mov (TBR),d0
+
+#ifdef CONFIG_SMP
+ add -4,sp
+ mov d0,(sp) # save d0(TBR)
+ movhu (NMIAGR),d0
+ and NMIAGR_GN,d0
+ lsr 0x2,d0
+ cmp CALL_FUNCTION_NMI_IPI,d0
+ bne 5f # if not call function, jump
+
+ # function call nmi ipi
+ add 4,sp # no need to store TBR
+ mov GxICR_DETECT,d0 # clear NMI request
+ movbu d0,(GxICR(CALL_FUNCTION_NMI_IPI))
+ movhu (GxICR(CALL_FUNCTION_NMI_IPI)),d0
+ and ~EPSW_NMID,epsw # enable NMI
+
+ mov (sp),d0 # restore d0
+ SAVE_ALL
+ call smp_nmi_call_function_interrupt[],0
+ RESTORE_ALL
+
+5:
+#ifdef CONFIG_GDBSTUB
+ cmp GDB_NMI_IPI,d0
+ bne 3f # if not gdb nmi ipi, jump
+
+ # gdb nmi ipi
+ add 4,sp # no need to store TBR
+ mov GxICR_DETECT,d0 # clear NMI
+ movbu d0,(GxICR(GDB_NMI_IPI))
+ movhu (GxICR(GDB_NMI_IPI)),d0
+ and ~EPSW_NMID,epsw # enable NMI
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+ mov (gdbstub_nmi_opr_type),d0
+ cmp GDBSTUB_NMI_CACHE_PURGE,d0
+ bne 4f # if not gdb cache purge, jump
+
+ # gdb cache purge nmi ipi
+ add -20,sp
+ mov d1,(4,sp)
+ mov a0,(8,sp)
+ mov a1,(12,sp)
+ mov mdr,d0
+ mov d0,(16,sp)
+ call gdbstub_local_purge_cache[],0
+ mov 0x1,d0
+ mov (CPUID),d1
+ asl d1,d0
+ mov gdbstub_nmi_cpumask,a0
+ bclr d0,(a0)
+ mov (4,sp),d1
+ mov (8,sp),a0
+ mov (12,sp),a1
+ mov (16,sp),d0
+ mov d0,mdr
+ add 20,sp
+ mov (sp),d0
+ add 4,sp
+ rti
+4:
+#endif /* CONFIG_MN10300_CACHE_ENABLED */
+ # gdb wait nmi ipi
+ mov (sp),d0
+ SAVE_ALL
+ call gdbstub_nmi_wait[],0
+ RESTORE_ALL
+3:
+#endif /* CONFIG_GDBSTUB */
+ mov (sp),d0 # restore TBR to d0
+ add 4,sp
+#endif /* CONFIG_SMP */
+
bra __common_exception_nonmi
ENTRY(__common_exception)
@@ -314,15 +379,21 @@
mov d0,(REG_ORIG_D0,fp)
#ifdef CONFIG_GDBSTUB
+#ifdef CONFIG_SMP
+ call gdbstub_busy_check[],0
+ and d0,d0 # check return value
+ beq 2f
+#else /* CONFIG_SMP */
btst 0x01,(gdbstub_busy)
beq 2f
+#endif /* CONFIG_SMP */
and ~EPSW_IE,epsw
mov fp,d0
mov a2,d1
call gdbstub_exception[],0 # gdbstub itself caused an exception
bra restore_all
2:
-#endif
+#endif /* CONFIG_GDBSTUB */
mov fp,d0 # arg 0: stacked register file
mov a2,d1 # arg 1: exception number
@@ -357,11 +428,7 @@
add exception_table,d0
mov d1,(d0)
mov 4,d1
-#if defined(CONFIG_MN10300_CACHE_WBACK)
- jmp mn10300_dcache_flush_inv_range2
-#else
ret [],0
-#endif
###############################################################################
#
diff --git a/arch/mn10300/kernel/gdb-io-serial-low.S b/arch/mn10300/kernel/gdb-io-serial-low.S
index 4998b24f..b1d0152 100644
--- a/arch/mn10300/kernel/gdb-io-serial-low.S
+++ b/arch/mn10300/kernel/gdb-io-serial-low.S
@@ -18,6 +18,7 @@
#include <asm/thread_info.h>
#include <asm/frame.inc>
#include <asm/intctl-regs.h>
+#include <asm/irqflags.h>
#include <unit/serial.h>
.text
@@ -69,7 +70,7 @@
bra gdbstub_io_rx_done
gdbstub_io_rx_enter:
- or EPSW_IE|EPSW_IM_1,epsw
+ LOCAL_CHANGE_INTR_MASK_LEVEL(NUM2EPSW_IM(CONFIG_GDBSTUB_IRQ_LEVEL+1))
add -4,sp
SAVE_ALL
@@ -80,7 +81,7 @@
mov fp,d0
call gdbstub_rx_irq[],0 # gdbstub_rx_irq(regs,excep)
- and ~EPSW_IE,epsw
+ LOCAL_CLI
bclr 0x01,(gdbstub_busy)
.globl gdbstub_return
diff --git a/arch/mn10300/kernel/gdb-io-serial.c b/arch/mn10300/kernel/gdb-io-serial.c
index ae663dc..0d5d63c 100644
--- a/arch/mn10300/kernel/gdb-io-serial.c
+++ b/arch/mn10300/kernel/gdb-io-serial.c
@@ -23,6 +23,7 @@
#include <asm/exceptions.h>
#include <asm/serial-regs.h>
#include <unit/serial.h>
+#include <asm/smp.h>
/*
* initialise the GDB stub
@@ -45,22 +46,34 @@
XIRQxICR(GDBPORT_SERIAL_IRQ) = 0;
tmp = XIRQxICR(GDBPORT_SERIAL_IRQ);
+#if CONFIG_GDBSTUB_IRQ_LEVEL == 0
IVAR0 = EXCEP_IRQ_LEVEL0;
- set_intr_stub(EXCEP_IRQ_LEVEL0, gdbstub_io_rx_handler);
+#elif CONFIG_GDBSTUB_IRQ_LEVEL == 1
+ IVAR1 = EXCEP_IRQ_LEVEL1;
+#elif CONFIG_GDBSTUB_IRQ_LEVEL == 2
+ IVAR2 = EXCEP_IRQ_LEVEL2;
+#elif CONFIG_GDBSTUB_IRQ_LEVEL == 3
+ IVAR3 = EXCEP_IRQ_LEVEL3;
+#elif CONFIG_GDBSTUB_IRQ_LEVEL == 4
+ IVAR4 = EXCEP_IRQ_LEVEL4;
+#elif CONFIG_GDBSTUB_IRQ_LEVEL == 5
+ IVAR5 = EXCEP_IRQ_LEVEL5;
+#else
+#error "Unknown irq level for gdbstub."
+#endif
+
+ set_intr_stub(NUM2EXCEP_IRQ_LEVEL(CONFIG_GDBSTUB_IRQ_LEVEL),
+ gdbstub_io_rx_handler);
XIRQxICR(GDBPORT_SERIAL_IRQ) &= ~GxICR_REQUEST;
- XIRQxICR(GDBPORT_SERIAL_IRQ) = GxICR_ENABLE | GxICR_LEVEL_0;
+ XIRQxICR(GDBPORT_SERIAL_IRQ) =
+ GxICR_ENABLE | NUM2GxICR_LEVEL(CONFIG_GDBSTUB_IRQ_LEVEL);
tmp = XIRQxICR(GDBPORT_SERIAL_IRQ);
GDBPORT_SERIAL_IER = UART_IER_RDI | UART_IER_RLSI;
/* permit level 0 IRQs to take place */
- asm volatile(
- " and %0,epsw \n"
- " or %1,epsw \n"
- :
- : "i"(~EPSW_IM), "i"(EPSW_IE | EPSW_IM_1)
- );
+ local_change_intr_mask_level(NUM2EPSW_IM(CONFIG_GDBSTUB_IRQ_LEVEL + 1));
}
/*
@@ -87,6 +100,9 @@
{
unsigned ix;
u8 ch, st;
+#if defined(CONFIG_MN10300_WD_TIMER)
+ int cpu;
+#endif
*_ch = 0xff;
@@ -104,8 +120,9 @@
if (nonblock)
return -EAGAIN;
#ifdef CONFIG_MN10300_WD_TIMER
- watchdog_alert_counter = 0;
-#endif /* CONFIG_MN10300_WD_TIMER */
+ for (cpu = 0; cpu < NR_CPUS; cpu++)
+ watchdog_alert_counter[cpu] = 0;
+#endif
goto try_again;
}
diff --git a/arch/mn10300/kernel/gdb-io-ttysm.c b/arch/mn10300/kernel/gdb-io-ttysm.c
index a560bbc..97dfda2 100644
--- a/arch/mn10300/kernel/gdb-io-ttysm.c
+++ b/arch/mn10300/kernel/gdb-io-ttysm.c
@@ -58,9 +58,12 @@
gdbstub_io_set_baud(115200);
/* we want to get serial receive interrupts */
- set_intr_level(gdbstub_port->rx_irq, GxICR_LEVEL_0);
- set_intr_level(gdbstub_port->tx_irq, GxICR_LEVEL_0);
- set_intr_stub(EXCEP_IRQ_LEVEL0, gdbstub_io_rx_handler);
+ set_intr_level(gdbstub_port->rx_irq,
+ NUM2GxICR_LEVEL(CONFIG_GDBSTUB_IRQ_LEVEL));
+ set_intr_level(gdbstub_port->tx_irq,
+ NUM2GxICR_LEVEL(CONFIG_GDBSTUB_IRQ_LEVEL));
+ set_intr_stub(NUM2EXCEP_IRQ_LEVEL(CONFIG_GDBSTUB_IRQ_LEVEL),
+ gdbstub_io_rx_handler);
*gdbstub_port->rx_icr |= GxICR_ENABLE;
tmp = *gdbstub_port->rx_icr;
@@ -84,12 +87,7 @@
tmp = *gdbstub_port->_control;
/* permit level 0 IRQs only */
- asm volatile(
- " and %0,epsw \n"
- " or %1,epsw \n"
- :
- : "i"(~EPSW_IM), "i"(EPSW_IE|EPSW_IM_1)
- );
+ local_change_intr_mask_level(NUM2EPSW_IM(CONFIG_GDBSTUB_IRQ_LEVEL + 1));
}
/*
@@ -184,6 +182,9 @@
{
unsigned ix;
u8 ch, st;
+#if defined(CONFIG_MN10300_WD_TIMER)
+ int cpu;
+#endif
*_ch = 0xff;
@@ -201,8 +202,9 @@
if (nonblock)
return -EAGAIN;
#ifdef CONFIG_MN10300_WD_TIMER
- watchdog_alert_counter = 0;
-#endif /* CONFIG_MN10300_WD_TIMER */
+ for (cpu = 0; cpu < NR_CPUS; cpu++)
+ watchdog_alert_counter[cpu] = 0;
+#endif
goto try_again;
}
diff --git a/arch/mn10300/kernel/gdb-stub.c b/arch/mn10300/kernel/gdb-stub.c
index 41b1170..a5fc3f0 100644
--- a/arch/mn10300/kernel/gdb-stub.c
+++ b/arch/mn10300/kernel/gdb-stub.c
@@ -440,15 +440,11 @@
static int __gdbstub_mark_bp(u8 *addr, int ix)
{
- if (addr < (u8 *) 0x70000000UL)
- return 0;
- /* 70000000-7fffffff: vmalloc area */
- if (addr < (u8 *) 0x80000000UL)
+ /* vmalloc area */
+ if (((u8 *) VMALLOC_START <= addr) && (addr < (u8 *) VMALLOC_END))
goto okay;
- if (addr < (u8 *) 0x8c000000UL)
- return 0;
- /* 8c000000-93ffffff: SRAM, SDRAM */
- if (addr < (u8 *) 0x94000000UL)
+ /* SRAM, SDRAM */
+ if (((u8 *) 0x80000000UL <= addr) && (addr < (u8 *) 0xa0000000UL))
goto okay;
return 0;
@@ -1197,9 +1193,8 @@
mn10300_set_gdbleds(1);
asm volatile("mov mdr,%0" : "=d"(mdr));
- asm volatile("mov epsw,%0" : "=d"(epsw));
- asm volatile("mov %0,epsw"
- :: "d"((epsw & ~EPSW_IM) | EPSW_IE | EPSW_IM_1));
+ local_save_flags(epsw);
+ local_change_intr_mask_level(NUM2EPSW_IM(CONFIG_GDBSTUB_IRQ_LEVEL + 1));
gdbstub_store_fpu();
diff --git a/arch/mn10300/kernel/head.S b/arch/mn10300/kernel/head.S
index a81e34f..73e00fc 100644
--- a/arch/mn10300/kernel/head.S
+++ b/arch/mn10300/kernel/head.S
@@ -19,6 +19,12 @@
#include <asm/frame.inc>
#include <asm/param.h>
#include <unit/serial.h>
+#ifdef CONFIG_SMP
+#include <asm/smp.h>
+#include <asm/intctl-regs.h>
+#include <asm/cpu-regs.h>
+#include <proc/smp-regs.h>
+#endif /* CONFIG_SMP */
__HEAD
@@ -30,17 +36,51 @@
.globl _start
.type _start,@function
_start:
+#ifdef CONFIG_SMP
+ #
+ # If this is a secondary CPU (AP), then deal with that elsewhere
+ #
+ mov (CPUID),d3
+ and CPUID_MASK,d3
+ bne startup_secondary
+
+ #
+ # We're dealing with the primary CPU (BP) here, then.
+ # Keep BP's D0,D1,D2 register for boot check.
+ #
+
+ # Set up the Boot IPI for each secondary CPU
+ mov 0x1,a0
+loop_set_secondary_icr:
+ mov a0,a1
+ asl CROSS_ICR_CPU_SHIFT,a1
+ add CROSS_GxICR(SMP_BOOT_IRQ,0),a1
+ movhu (a1),d3
+ or GxICR_ENABLE|GxICR_LEVEL_0,d3
+ movhu d3,(a1)
+ movhu (a1),d3 # flush
+ inc a0
+ cmp NR_CPUS,a0
+ bne loop_set_secondary_icr
+#endif /* CONFIG_SMP */
+
# save commandline pointer
mov d0,a3
# preload the PGD pointer register
mov swapper_pg_dir,d0
mov d0,(PTBR)
+ clr d0
+ movbu d0,(PIDR)
# turn on the TLBs
mov MMUCTR_IIV|MMUCTR_DIV,d0
mov d0,(MMUCTR)
+#ifdef CONFIG_AM34_2
+ mov MMUCTR_ITE|MMUCTR_DTE|MMUCTR_CE|MMUCTR_WTE,d0
+#else
mov MMUCTR_ITE|MMUCTR_DTE|MMUCTR_CE,d0
+#endif
mov d0,(MMUCTR)
# turn on AM33v2 exception handling mode and set the trap table base
@@ -51,6 +91,11 @@
mov d0,(TBR)
# invalidate and enable both of the caches
+#ifdef CONFIG_SMP
+ mov ECHCTR,a0
+ clr d0
+ mov d0,(a0)
+#endif
mov CHCTR,a0
clr d0
movhu d0,(a0) # turn off first
@@ -206,6 +251,44 @@
call processor_init[],0
call unit_init[],0
+#ifdef CONFIG_SMP
+ # mark the primary CPU in cpu_boot_map
+ mov cpu_boot_map,a0
+ mov 0x1,d0
+ mov d0,(a0)
+
+ # signal each secondary CPU to begin booting
+ mov 0x1,d2 # CPU ID
+
+loop_request_boot_secondary:
+ mov d2,a0
+ # send SMP_BOOT_IPI to secondary CPU
+ asl CROSS_ICR_CPU_SHIFT,a0
+ add CROSS_GxICR(SMP_BOOT_IRQ,0),a0
+ movhu (a0),d0
+ or GxICR_REQUEST|GxICR_DETECT,d0
+ movhu d0,(a0)
+ movhu (a0),d0 # flush
+
+ # wait up to 100ms for AP's IPI to be received
+ clr d3
+wait_on_secondary_boot:
+ mov DELAY_TIME_BOOT_IPI,d0
+ call __delay[],0
+ inc d3
+ mov cpu_boot_map,a0
+ mov (a0),d0
+ lsr d2,d0
+ btst 0x1,d0
+ bne 1f
+ cmp TIME_OUT_COUNT_BOOT_IPI,d3
+ bne wait_on_secondary_boot
+1:
+ inc d2
+ cmp NR_CPUS,d2
+ bne loop_request_boot_secondary
+#endif /* CONFIG_SMP */
+
#ifdef CONFIG_GDBSTUB
call gdbstub_init[],0
@@ -217,7 +300,118 @@
#endif
jmp start_kernel
- .size _start, _start-.
+ .size _start,.-_start
+
+###############################################################################
+#
+# Secondary CPU boot point
+#
+###############################################################################
+#ifdef CONFIG_SMP
+startup_secondary:
+ # preload the PGD pointer register
+ mov swapper_pg_dir,d0
+ mov d0,(PTBR)
+ clr d0
+ movbu d0,(PIDR)
+
+ # turn on the TLBs
+ mov MMUCTR_IIV|MMUCTR_DIV,d0
+ mov d0,(MMUCTR)
+#ifdef CONFIG_AM34_2
+ mov MMUCTR_ITE|MMUCTR_DTE|MMUCTR_CE|MMUCTR_WTE,d0
+#else
+ mov MMUCTR_ITE|MMUCTR_DTE|MMUCTR_CE,d0
+#endif
+ mov d0,(MMUCTR)
+
+ # turn on AM33v2 exception handling mode and set the trap table base
+ movhu (CPUP),d0
+ or CPUP_EXM_AM33V2,d0
+ movhu d0,(CPUP)
+
+ # set the interrupt vector table
+ mov CONFIG_INTERRUPT_VECTOR_BASE,d0
+ mov d0,(TBR)
+
+ # invalidate and enable both of the caches
+ mov ECHCTR,a0
+ clr d0
+ mov d0,(a0)
+ mov CHCTR,a0
+ clr d0
+ movhu d0,(a0) # turn off first
+ mov CHCTR_ICINV|CHCTR_DCINV,d0
+ movhu d0,(a0)
+ setlb
+ mov (a0),d0
+ btst CHCTR_ICBUSY|CHCTR_DCBUSY,d0 # wait till not busy (use CPU loop buffer)
+ lne
+
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+#ifdef CONFIG_MN10300_CACHE_WBACK
+#ifndef CONFIG_MN10300_CACHE_WBACK_NOWRALLOC
+ mov CHCTR_ICEN|CHCTR_DCEN|CHCTR_DCWTMD_WRBACK,d0
+#else
+ mov CHCTR_ICEN|CHCTR_DCEN|CHCTR_DCWTMD_WRBACK|CHCTR_DCALMD,d0
+#endif /* !NOWRALLOC */
+#else
+ mov CHCTR_ICEN|CHCTR_DCEN|CHCTR_DCWTMD_WRTHROUGH,d0
+#endif /* WBACK */
+ movhu d0,(a0) # enable
+#endif /* ENABLED */
+
+ # Clear the boot IPI interrupt for this CPU
+ movhu (GxICR(SMP_BOOT_IRQ)),d0
+ and ~GxICR_REQUEST,d0
+ movhu d0,(GxICR(SMP_BOOT_IRQ))
+ movhu (GxICR(SMP_BOOT_IRQ)),d0 # flush
+
+ /* get stack */
+ mov CONFIG_INTERRUPT_VECTOR_BASE + CONFIG_BOOT_STACK_OFFSET,a0
+ mov (CPUID),d0
+ and CPUID_MASK,d0
+ mulu CONFIG_BOOT_STACK_SIZE,d0
+ sub d0,a0
+ mov a0,sp
+
+ # init interrupt for AP
+ call smp_prepare_cpu_init[],0
+
+ # mark this secondary CPU in cpu_boot_map
+ mov (CPUID),d0
+ mov 0x1,d1
+ asl d0,d1
+ mov cpu_boot_map,a0
+ bset d1,(a0)
+
+ or EPSW_IE|EPSW_IM_1,epsw # permit level 0 interrupts
+ nop
+ nop
+#ifdef CONFIG_MN10300_CACHE_WBACK
+ # flush the local cache if it's in writeback mode
+ call mn10300_local_dcache_flush_inv[],0
+ setlb
+ mov (CHCTR),d0
+ btst CHCTR_DCBUSY,d0 # wait till not busy (use CPU loop buffer)
+ lne
+#endif
+
+ # now sleep waiting for further instructions
+secondary_sleep:
+ mov CPUM_SLEEP,d0
+ movhu d0,(CPUM)
+ nop
+ nop
+ bra secondary_sleep
+ .size startup_secondary,.-startup_secondary
+#endif /* CONFIG_SMP */
+
+###############################################################################
+#
+#
+#
+###############################################################################
ENTRY(__head_end)
/*
diff --git a/arch/mn10300/kernel/internal.h b/arch/mn10300/kernel/internal.h
index eee2eee..3b1f48b 100644
--- a/arch/mn10300/kernel/internal.h
+++ b/arch/mn10300/kernel/internal.h
@@ -18,3 +18,15 @@
* entry.S
*/
extern void ret_from_fork(struct task_struct *) __attribute__((noreturn));
+
+/*
+ * smp-low.S
+ */
+#ifdef CONFIG_SMP
+extern void mn10300_low_ipi_handler(void);
+#endif
+
+/*
+ * time.c
+ */
+extern irqreturn_t local_timer_interrupt(void);
diff --git a/arch/mn10300/kernel/irq.c b/arch/mn10300/kernel/irq.c
index b5b970d..80f1572 100644
--- a/arch/mn10300/kernel/irq.c
+++ b/arch/mn10300/kernel/irq.c
@@ -12,11 +12,34 @@
#include <linux/interrupt.h>
#include <linux/kernel_stat.h>
#include <linux/seq_file.h>
+#include <linux/cpumask.h>
#include <asm/setup.h>
+#include <asm/serial-regs.h>
-unsigned long __mn10300_irq_enabled_epsw = EPSW_IE | EPSW_IM_7;
+#ifdef CONFIG_SMP
+#undef GxICR
+#define GxICR(X) CROSS_GxICR(X, irq_affinity_online[X])
+
+#undef GxICR_u8
+#define GxICR_u8(X) CROSS_GxICR_u8(X, irq_affinity_online[X])
+#endif /* CONFIG_SMP */
+
+unsigned long __mn10300_irq_enabled_epsw[NR_CPUS] __cacheline_aligned_in_smp = {
+ [0 ... NR_CPUS - 1] = EPSW_IE | EPSW_IM_7
+};
EXPORT_SYMBOL(__mn10300_irq_enabled_epsw);
+#ifdef CONFIG_SMP
+static char irq_affinity_online[NR_IRQS] = {
+ [0 ... NR_IRQS - 1] = 0
+};
+
+#define NR_IRQ_WORDS ((NR_IRQS + 31) / 32)
+static unsigned long irq_affinity_request[NR_IRQ_WORDS] = {
+ [0 ... NR_IRQ_WORDS - 1] = 0
+};
+#endif /* CONFIG_SMP */
+
atomic_t irq_err_count;
/*
@@ -24,30 +47,65 @@
*/
static void mn10300_cpupic_ack(unsigned int irq)
{
+ unsigned long flags;
u16 tmp;
- *(volatile u8 *) &GxICR(irq) = GxICR_DETECT;
+
+ flags = arch_local_cli_save();
+ GxICR_u8(irq) = GxICR_DETECT;
tmp = GxICR(irq);
+ arch_local_irq_restore(flags);
+}
+
+static void __mask_and_set_icr(unsigned int irq,
+ unsigned int mask, unsigned int set)
+{
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & mask) | set;
+ tmp = GxICR(irq);
+ arch_local_irq_restore(flags);
}
static void mn10300_cpupic_mask(unsigned int irq)
{
- u16 tmp = GxICR(irq);
- GxICR(irq) = (tmp & GxICR_LEVEL);
- tmp = GxICR(irq);
+ __mask_and_set_icr(irq, GxICR_LEVEL, 0);
}
static void mn10300_cpupic_mask_ack(unsigned int irq)
{
- u16 tmp = GxICR(irq);
- GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_DETECT;
- tmp = GxICR(irq);
+#ifdef CONFIG_SMP
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+
+ if (!test_and_clear_bit(irq, irq_affinity_request)) {
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_DETECT;
+ tmp = GxICR(irq);
+ } else {
+ u16 tmp2;
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & GxICR_LEVEL);
+ tmp2 = GxICR(irq);
+
+ irq_affinity_online[irq] = any_online_cpu(*irq_desc[irq].affinity);
+ GxICR(irq) = (tmp & (GxICR_LEVEL | GxICR_ENABLE)) | GxICR_DETECT;
+ tmp = GxICR(irq);
+ }
+
+ arch_local_irq_restore(flags);
+#else /* CONFIG_SMP */
+ __mask_and_set_icr(irq, GxICR_LEVEL, GxICR_DETECT);
+#endif /* CONFIG_SMP */
}
static void mn10300_cpupic_unmask(unsigned int irq)
{
- u16 tmp = GxICR(irq);
- GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_ENABLE;
- tmp = GxICR(irq);
+ __mask_and_set_icr(irq, GxICR_LEVEL, GxICR_ENABLE);
}
static void mn10300_cpupic_unmask_clear(unsigned int irq)
@@ -56,11 +114,89 @@
* device has ceased to assert its interrupt line and the interrupt
* channel has been disabled in the PIC, so for level-triggered
* interrupts we need to clear the request bit when we re-enable */
- u16 tmp = GxICR(irq);
- GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_ENABLE | GxICR_DETECT;
- tmp = GxICR(irq);
+#ifdef CONFIG_SMP
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+
+ if (!test_and_clear_bit(irq, irq_affinity_request)) {
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_ENABLE | GxICR_DETECT;
+ tmp = GxICR(irq);
+ } else {
+ tmp = GxICR(irq);
+
+ irq_affinity_online[irq] = any_online_cpu(*irq_desc[irq].affinity);
+ GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_ENABLE | GxICR_DETECT;
+ tmp = GxICR(irq);
+ }
+
+ arch_local_irq_restore(flags);
+#else /* CONFIG_SMP */
+ __mask_and_set_icr(irq, GxICR_LEVEL, GxICR_ENABLE | GxICR_DETECT);
+#endif /* CONFIG_SMP */
}
+#ifdef CONFIG_SMP
+static int
+mn10300_cpupic_setaffinity(unsigned int irq, const struct cpumask *mask)
+{
+ unsigned long flags;
+ int err;
+
+ flags = arch_local_cli_save();
+
+ /* check irq no */
+ switch (irq) {
+ case TMJCIRQ:
+ case RESCHEDULE_IPI:
+ case CALL_FUNC_SINGLE_IPI:
+ case LOCAL_TIMER_IPI:
+ case FLUSH_CACHE_IPI:
+ case CALL_FUNCTION_NMI_IPI:
+ case GDB_NMI_IPI:
+#ifdef CONFIG_MN10300_TTYSM0
+ case SC0RXIRQ:
+ case SC0TXIRQ:
+#ifdef CONFIG_MN10300_TTYSM0_TIMER8
+ case TM8IRQ:
+#elif CONFIG_MN10300_TTYSM0_TIMER2
+ case TM2IRQ:
+#endif /* CONFIG_MN10300_TTYSM0_TIMER8 */
+#endif /* CONFIG_MN10300_TTYSM0 */
+
+#ifdef CONFIG_MN10300_TTYSM1
+ case SC1RXIRQ:
+ case SC1TXIRQ:
+#ifdef CONFIG_MN10300_TTYSM1_TIMER12
+ case TM12IRQ:
+#elif CONFIG_MN10300_TTYSM1_TIMER9
+ case TM9IRQ:
+#elif CONFIG_MN10300_TTYSM1_TIMER3
+ case TM3IRQ:
+#endif /* CONFIG_MN10300_TTYSM1_TIMER12 */
+#endif /* CONFIG_MN10300_TTYSM1 */
+
+#ifdef CONFIG_MN10300_TTYSM2
+ case SC2RXIRQ:
+ case SC2TXIRQ:
+ case TM10IRQ:
+#endif /* CONFIG_MN10300_TTYSM2 */
+ err = -1;
+ break;
+
+ default:
+ set_bit(irq, irq_affinity_request);
+ err = 0;
+ break;
+ }
+
+ arch_local_irq_restore(flags);
+ return err;
+}
+#endif /* CONFIG_SMP */
+
/*
* MN10300 PIC level-triggered IRQ handling.
*
@@ -79,6 +215,9 @@
.mask = mn10300_cpupic_mask,
.mask_ack = mn10300_cpupic_mask,
.unmask = mn10300_cpupic_unmask_clear,
+#ifdef CONFIG_SMP
+ .set_affinity = mn10300_cpupic_setaffinity,
+#endif /* CONFIG_SMP */
};
/*
@@ -94,6 +233,9 @@
.mask = mn10300_cpupic_mask,
.mask_ack = mn10300_cpupic_mask_ack,
.unmask = mn10300_cpupic_unmask,
+#ifdef CONFIG_SMP
+ .set_affinity = mn10300_cpupic_setaffinity,
+#endif /* CONFIG_SMP */
};
/*
@@ -111,14 +253,34 @@
*/
void set_intr_level(int irq, u16 level)
{
- u16 tmp;
+ BUG_ON(in_interrupt());
- if (in_interrupt())
- BUG();
+ __mask_and_set_icr(irq, GxICR_ENABLE, level);
+}
- tmp = GxICR(irq);
- GxICR(irq) = (tmp & GxICR_ENABLE) | level;
- tmp = GxICR(irq);
+void mn10300_intc_set_level(unsigned int irq, unsigned int level)
+{
+ set_intr_level(irq, NUM2GxICR_LEVEL(level) & GxICR_LEVEL);
+}
+
+void mn10300_intc_clear(unsigned int irq)
+{
+ __mask_and_set_icr(irq, GxICR_LEVEL | GxICR_ENABLE, GxICR_DETECT);
+}
+
+void mn10300_intc_set(unsigned int irq)
+{
+ __mask_and_set_icr(irq, 0, GxICR_REQUEST | GxICR_DETECT);
+}
+
+void mn10300_intc_enable(unsigned int irq)
+{
+ mn10300_cpupic_unmask(irq);
+}
+
+void mn10300_intc_disable(unsigned int irq)
+{
+ mn10300_cpupic_mask(irq);
}
/*
@@ -126,7 +288,7 @@
* than before
* - see Documentation/mn10300/features.txt
*/
-void set_intr_postackable(int irq)
+void mn10300_set_lateack_irq_type(int irq)
{
set_irq_chip_and_handler(irq, &mn10300_cpu_pic_level,
handle_level_irq);
@@ -147,6 +309,7 @@
* interrupts */
set_irq_chip_and_handler(irq, &mn10300_cpu_pic_edge,
handle_level_irq);
+
unit_init_IRQ();
}
@@ -156,6 +319,7 @@
asmlinkage void do_IRQ(void)
{
unsigned long sp, epsw, irq_disabled_epsw, old_irq_enabled_epsw;
+ unsigned int cpu_id = smp_processor_id();
int irq;
sp = current_stack_pointer();
@@ -163,12 +327,14 @@
/* make sure local_irq_enable() doesn't muck up the interrupt priority
* setting in EPSW */
- old_irq_enabled_epsw = __mn10300_irq_enabled_epsw;
+ old_irq_enabled_epsw = __mn10300_irq_enabled_epsw[cpu_id];
local_save_flags(epsw);
- __mn10300_irq_enabled_epsw = EPSW_IE | (EPSW_IM & epsw);
+ __mn10300_irq_enabled_epsw[cpu_id] = EPSW_IE | (EPSW_IM & epsw);
irq_disabled_epsw = EPSW_IE | MN10300_CLI_LEVEL;
- __IRQ_STAT(smp_processor_id(), __irq_count)++;
+#ifdef CONFIG_MN10300_WD_TIMER
+ __IRQ_STAT(cpu_id, __irq_count)++;
+#endif
irq_enter();
@@ -188,7 +354,7 @@
local_irq_restore(epsw);
}
- __mn10300_irq_enabled_epsw = old_irq_enabled_epsw;
+ __mn10300_irq_enabled_epsw[cpu_id] = old_irq_enabled_epsw;
irq_exit();
}
@@ -239,11 +405,13 @@
/* polish off with NMI and error counters */
case NR_IRQS:
+#ifdef CONFIG_MN10300_WD_TIMER
seq_printf(p, "NMI: ");
for (j = 0; j < NR_CPUS; j++)
if (cpu_online(j))
seq_printf(p, "%10u ", nmi_count(j));
seq_putc(p, '\n');
+#endif
seq_printf(p, "ERR: %10u\n", atomic_read(&irq_err_count));
break;
@@ -251,3 +419,51 @@
return 0;
}
+
+#ifdef CONFIG_HOTPLUG_CPU
+void migrate_irqs(void)
+{
+ irq_desc_t *desc;
+ int irq;
+ unsigned int self, new;
+ unsigned long flags;
+
+ self = smp_processor_id();
+ for (irq = 0; irq < NR_IRQS; irq++) {
+ desc = irq_desc + irq;
+
+ if (desc->status == IRQ_PER_CPU)
+ continue;
+
+ if (cpu_isset(self, irq_desc[irq].affinity) &&
+ !cpus_intersects(irq_affinity[irq], cpu_online_map)) {
+ int cpu_id;
+ cpu_id = first_cpu(cpu_online_map);
+ cpu_set(cpu_id, irq_desc[irq].affinity);
+ }
+ /* We need to operate irq_affinity_online atomically. */
+ arch_local_cli_save(flags);
+ if (irq_affinity_online[irq] == self) {
+ u16 x, tmp;
+
+ x = CROSS_GxICR(irq, self);
+ CROSS_GxICR(irq, self) = x & GxICR_LEVEL;
+ tmp = CROSS_GxICR(irq, self);
+
+ new = any_online_cpu(irq_desc[irq].affinity);
+ irq_affinity_online[irq] = new;
+
+ CROSS_GxICR(irq, new) =
+ (x & GxICR_LEVEL) | GxICR_DETECT;
+ tmp = CROSS_GxICR(irq, new);
+
+ x &= GxICR_LEVEL | GxICR_ENABLE;
+ if (CROSS_GxICR(irq, self) & GxICR_REQUEST)
+ x |= GxICR_REQUEST | GxICR_DETECT;
+ CROSS_GxICR(irq, new) = x;
+ tmp = CROSS_GxICR(irq, new);
+ }
+ arch_local_irq_restore(flags);
+ }
+}
+#endif /* CONFIG_HOTPLUG_CPU */
diff --git a/arch/mn10300/kernel/mn10300-serial-low.S b/arch/mn10300/kernel/mn10300-serial-low.S
index 66702d2..dfc1b6f 100644
--- a/arch/mn10300/kernel/mn10300-serial-low.S
+++ b/arch/mn10300/kernel/mn10300-serial-low.S
@@ -39,7 +39,7 @@
###############################################################################
.balign L1_CACHE_BYTES
ENTRY(mn10300_serial_vdma_interrupt)
- or EPSW_IE,psw # permit overriding by
+# or EPSW_IE,psw # permit overriding by
# debugging interrupts
movm [d2,d3,a2,a3,exreg0],(sp)
@@ -164,7 +164,7 @@
rti
mnsc_vdma_tx_empty:
- mov +(GxICR_LEVEL_1|GxICR_DETECT),d2
+ mov +(NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL)|GxICR_DETECT),d2
movhu d2,(e3) # disable the interrupt
movhu (e3),d2 # flush
@@ -175,7 +175,7 @@
movhu (SCxCTR,e2),d2 # turn on break mode
or SC01CTR_BKE,d2
movhu d2,(SCxCTR,e2)
- mov +(GxICR_LEVEL_1|GxICR_DETECT),d2
+ mov +(NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL)|GxICR_DETECT),d2
movhu d2,(e3) # disable transmit interrupts on this
# channel
movhu (e3),d2 # flush
diff --git a/arch/mn10300/kernel/mn10300-serial.c b/arch/mn10300/kernel/mn10300-serial.c
index db509dd..996384d 100644
--- a/arch/mn10300/kernel/mn10300-serial.c
+++ b/arch/mn10300/kernel/mn10300-serial.c
@@ -44,6 +44,11 @@
#include <unit/timex.h>
#include "mn10300-serial.h"
+#ifdef CONFIG_SMP
+#undef GxICR
+#define GxICR(X) CROSS_GxICR(X, 0)
+#endif /* CONFIG_SMP */
+
#define kenter(FMT, ...) \
printk(KERN_DEBUG "-->%s(" FMT ")\n", __func__, ##__VA_ARGS__)
#define _enter(FMT, ...) \
@@ -57,6 +62,11 @@
#define _proto(FMT, ...) \
no_printk(KERN_DEBUG "### MNSERIAL " FMT " ###\n", ##__VA_ARGS__)
+#ifndef CODMSB
+/* c_cflag bit meaning */
+#define CODMSB 004000000000 /* change Transfer bit-order */
+#endif
+
#define NR_UARTS 3
#ifdef CONFIG_MN10300_TTYSM_CONSOLE
@@ -152,26 +162,35 @@
.name = "ttySM0",
._iobase = &SC0CTR,
._control = &SC0CTR,
- ._status = (volatile u8 *) &SC0STR,
+ ._status = (volatile u8 *)&SC0STR,
._intr = &SC0ICR,
._rxb = &SC0RXB,
._txb = &SC0TXB,
.rx_name = "ttySM0:Rx",
.tx_name = "ttySM0:Tx",
-#ifdef CONFIG_MN10300_TTYSM0_TIMER8
+#if defined(CONFIG_MN10300_TTYSM0_TIMER8)
.tm_name = "ttySM0:Timer8",
._tmxmd = &TM8MD,
._tmxbr = &TM8BR,
._tmicr = &TM8ICR,
.tm_irq = TM8IRQ,
.div_timer = MNSCx_DIV_TIMER_16BIT,
-#else /* CONFIG_MN10300_TTYSM0_TIMER2 */
+#elif defined(CONFIG_MN10300_TTYSM0_TIMER0)
+ .tm_name = "ttySM0:Timer0",
+ ._tmxmd = &TM0MD,
+ ._tmxbr = (volatile u16 *)&TM0BR,
+ ._tmicr = &TM0ICR,
+ .tm_irq = TM0IRQ,
+ .div_timer = MNSCx_DIV_TIMER_8BIT,
+#elif defined(CONFIG_MN10300_TTYSM0_TIMER2)
.tm_name = "ttySM0:Timer2",
._tmxmd = &TM2MD,
- ._tmxbr = (volatile u16 *) &TM2BR,
+ ._tmxbr = (volatile u16 *)&TM2BR,
._tmicr = &TM2ICR,
.tm_irq = TM2IRQ,
.div_timer = MNSCx_DIV_TIMER_8BIT,
+#else
+#error "Unknown config for ttySM0"
#endif
.rx_irq = SC0RXIRQ,
.tx_irq = SC0TXIRQ,
@@ -205,26 +224,35 @@
.name = "ttySM1",
._iobase = &SC1CTR,
._control = &SC1CTR,
- ._status = (volatile u8 *) &SC1STR,
+ ._status = (volatile u8 *)&SC1STR,
._intr = &SC1ICR,
._rxb = &SC1RXB,
._txb = &SC1TXB,
.rx_name = "ttySM1:Rx",
.tx_name = "ttySM1:Tx",
-#ifdef CONFIG_MN10300_TTYSM1_TIMER9
+#if defined(CONFIG_MN10300_TTYSM1_TIMER9)
.tm_name = "ttySM1:Timer9",
._tmxmd = &TM9MD,
._tmxbr = &TM9BR,
._tmicr = &TM9ICR,
.tm_irq = TM9IRQ,
.div_timer = MNSCx_DIV_TIMER_16BIT,
-#else /* CONFIG_MN10300_TTYSM1_TIMER3 */
+#elif defined(CONFIG_MN10300_TTYSM1_TIMER3)
.tm_name = "ttySM1:Timer3",
._tmxmd = &TM3MD,
- ._tmxbr = (volatile u16 *) &TM3BR,
+ ._tmxbr = (volatile u16 *)&TM3BR,
._tmicr = &TM3ICR,
.tm_irq = TM3IRQ,
.div_timer = MNSCx_DIV_TIMER_8BIT,
+#elif defined(CONFIG_MN10300_TTYSM1_TIMER12)
+ .tm_name = "ttySM1/Timer12",
+ ._tmxmd = &TM12MD,
+ ._tmxbr = &TM12BR,
+ ._tmicr = &TM12ICR,
+ .tm_irq = TM12IRQ,
+ .div_timer = MNSCx_DIV_TIMER_16BIT,
+#else
+#error "Unknown config for ttySM1"
#endif
.rx_irq = SC1RXIRQ,
.tx_irq = SC1TXIRQ,
@@ -260,20 +288,45 @@
.uart.lock =
__SPIN_LOCK_UNLOCKED(mn10300_serial_port_sif2.uart.lock),
.name = "ttySM2",
- .rx_name = "ttySM2:Rx",
- .tx_name = "ttySM2:Tx",
- .tm_name = "ttySM2:Timer10",
._iobase = &SC2CTR,
._control = &SC2CTR,
- ._status = &SC2STR,
+ ._status = (volatile u8 *)&SC2STR,
._intr = &SC2ICR,
._rxb = &SC2RXB,
._txb = &SC2TXB,
+ .rx_name = "ttySM2:Rx",
+ .tx_name = "ttySM2:Tx",
+#if defined(CONFIG_MN10300_TTYSM2_TIMER10)
+ .tm_name = "ttySM2/Timer10",
._tmxmd = &TM10MD,
._tmxbr = &TM10BR,
._tmicr = &TM10ICR,
.tm_irq = TM10IRQ,
.div_timer = MNSCx_DIV_TIMER_16BIT,
+#elif defined(CONFIG_MN10300_TTYSM2_TIMER9)
+ .tm_name = "ttySM2/Timer9",
+ ._tmxmd = &TM9MD,
+ ._tmxbr = &TM9BR,
+ ._tmicr = &TM9ICR,
+ .tm_irq = TM9IRQ,
+ .div_timer = MNSCx_DIV_TIMER_16BIT,
+#elif defined(CONFIG_MN10300_TTYSM2_TIMER1)
+ .tm_name = "ttySM2/Timer1",
+ ._tmxmd = &TM1MD,
+ ._tmxbr = (volatile u16 *)&TM1BR,
+ ._tmicr = &TM1ICR,
+ .tm_irq = TM1IRQ,
+ .div_timer = MNSCx_DIV_TIMER_8BIT,
+#elif defined(CONFIG_MN10300_TTYSM2_TIMER3)
+ .tm_name = "ttySM2/Timer3",
+ ._tmxmd = &TM3MD,
+ ._tmxbr = (volatile u16 *)&TM3BR,
+ ._tmicr = &TM3ICR,
+ .tm_irq = TM3IRQ,
+ .div_timer = MNSCx_DIV_TIMER_8BIT,
+#else
+#error "Unknown config for ttySM2"
+#endif
.rx_irq = SC2RXIRQ,
.tx_irq = SC2TXIRQ,
.rx_icr = &GxICR(SC2RXIRQ),
@@ -322,9 +375,13 @@
*/
static void mn10300_serial_mask_ack(unsigned int irq)
{
+ unsigned long flags;
u16 tmp;
+
+ flags = arch_local_cli_save();
GxICR(irq) = GxICR_LEVEL_6;
tmp = GxICR(irq); /* flush write buffer */
+ arch_local_irq_restore(flags);
}
static void mn10300_serial_nop(unsigned int irq)
@@ -348,23 +405,36 @@
static void mn10300_serial_dis_tx_intr(struct mn10300_serial_port *port)
{
+ unsigned long flags;
u16 x;
- *port->tx_icr = GxICR_LEVEL_1 | GxICR_DETECT;
+
+ flags = arch_local_cli_save();
+ *port->tx_icr = NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL);
x = *port->tx_icr;
+ arch_local_irq_restore(flags);
}
static void mn10300_serial_en_tx_intr(struct mn10300_serial_port *port)
{
+ unsigned long flags;
u16 x;
- *port->tx_icr = GxICR_LEVEL_1 | GxICR_ENABLE;
+
+ flags = arch_local_cli_save();
+ *port->tx_icr =
+ NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL) | GxICR_ENABLE;
x = *port->tx_icr;
+ arch_local_irq_restore(flags);
}
static void mn10300_serial_dis_rx_intr(struct mn10300_serial_port *port)
{
+ unsigned long flags;
u16 x;
- *port->rx_icr = GxICR_LEVEL_1 | GxICR_DETECT;
+
+ flags = arch_local_cli_save();
+ *port->rx_icr = NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL);
x = *port->rx_icr;
+ arch_local_irq_restore(flags);
}
/*
@@ -650,7 +720,7 @@
static void mn10300_serial_set_mctrl(struct uart_port *_port,
unsigned int mctrl)
{
- struct mn10300_serial_port *port =
+ struct mn10300_serial_port *port __attribute__ ((unused)) =
container_of(_port, struct mn10300_serial_port, uart);
_enter("%s,%x", port->name, mctrl);
@@ -706,6 +776,7 @@
UART_XMIT_SIZE));
/* kick the virtual DMA controller */
+ arch_local_cli();
x = *port->tx_icr;
x |= GxICR_ENABLE;
@@ -716,10 +787,14 @@
_debug("CTR=%04hx ICR=%02hx STR=%04x TMD=%02hx TBR=%04hx ICR=%04hx",
*port->_control, *port->_intr, *port->_status,
- *port->_tmxmd, *port->_tmxbr, *port->tx_icr);
+ *port->_tmxmd,
+ (port->div_timer == MNSCx_DIV_TIMER_8BIT) ?
+ *(volatile u8 *)port->_tmxbr : *port->_tmxbr,
+ *port->tx_icr);
*port->tx_icr = x;
x = *port->tx_icr;
+ arch_local_sti();
}
/*
@@ -842,8 +917,10 @@
pint->port = port;
pint->vdma = mn10300_serial_vdma_tx_handler;
- set_intr_level(port->rx_irq, GxICR_LEVEL_1);
- set_intr_level(port->tx_irq, GxICR_LEVEL_1);
+ set_intr_level(port->rx_irq,
+ NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL));
+ set_intr_level(port->tx_irq,
+ NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL));
set_irq_chip(port->tm_irq, &mn10300_serial_pic);
if (request_irq(port->rx_irq, mn10300_serial_interrupt,
@@ -876,6 +953,7 @@
*/
static void mn10300_serial_shutdown(struct uart_port *_port)
{
+ u16 x;
struct mn10300_serial_port *port =
container_of(_port, struct mn10300_serial_port, uart);
@@ -897,8 +975,12 @@
free_irq(port->rx_irq, port);
free_irq(port->tx_irq, port);
- *port->rx_icr = GxICR_LEVEL_1;
- *port->tx_icr = GxICR_LEVEL_1;
+ arch_local_cli();
+ *port->rx_icr = NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL);
+ x = *port->rx_icr;
+ *port->tx_icr = NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL);
+ x = *port->tx_icr;
+ arch_local_sti();
}
/*
@@ -947,11 +1029,66 @@
/* Determine divisor based on baud rate */
battempt = 0;
- if (div_timer == MNSCx_DIV_TIMER_16BIT)
- scxctr |= SC0CTR_CK_TM8UFLOW_8; /* ( == SC1CTR_CK_TM9UFLOW_8
- * == SC2CTR_CK_TM10UFLOW) */
- else if (div_timer == MNSCx_DIV_TIMER_8BIT)
+ switch (port->uart.line) {
+#ifdef CONFIG_MN10300_TTYSM0
+ case 0: /* ttySM0 */
+#if defined(CONFIG_MN10300_TTYSM0_TIMER8)
+ scxctr |= SC0CTR_CK_TM8UFLOW_8;
+#elif defined(CONFIG_MN10300_TTYSM0_TIMER0)
+ scxctr |= SC0CTR_CK_TM0UFLOW_8;
+#elif defined(CONFIG_MN10300_TTYSM0_TIMER2)
scxctr |= SC0CTR_CK_TM2UFLOW_8;
+#else
+#error "Unknown config for ttySM0"
+#endif
+ break;
+#endif /* CONFIG_MN10300_TTYSM0 */
+
+#ifdef CONFIG_MN10300_TTYSM1
+ case 1: /* ttySM1 */
+#if defined(CONFIG_AM33_2) || defined(CONFIG_AM33_3)
+#if defined(CONFIG_MN10300_TTYSM1_TIMER9)
+ scxctr |= SC1CTR_CK_TM9UFLOW_8;
+#elif defined(CONFIG_MN10300_TTYSM1_TIMER3)
+ scxctr |= SC1CTR_CK_TM3UFLOW_8;
+#else
+#error "Unknown config for ttySM1"
+#endif
+#else /* CONFIG_AM33_2 || CONFIG_AM33_3 */
+#if defined(CONFIG_MN10300_TTYSM1_TIMER12)
+ scxctr |= SC1CTR_CK_TM12UFLOW_8;
+#else
+#error "Unknown config for ttySM1"
+#endif
+#endif /* CONFIG_AM33_2 || CONFIG_AM33_3 */
+ break;
+#endif /* CONFIG_MN10300_TTYSM1 */
+
+#ifdef CONFIG_MN10300_TTYSM2
+ case 2: /* ttySM2 */
+#if defined(CONFIG_AM33_2)
+#if defined(CONFIG_MN10300_TTYSM2_TIMER10)
+ scxctr |= SC2CTR_CK_TM10UFLOW;
+#else
+#error "Unknown config for ttySM2"
+#endif
+#else /* CONFIG_AM33_2 */
+#if defined(CONFIG_MN10300_TTYSM2_TIMER9)
+ scxctr |= SC2CTR_CK_TM9UFLOW_8;
+#elif defined(CONFIG_MN10300_TTYSM2_TIMER1)
+ scxctr |= SC2CTR_CK_TM1UFLOW_8;
+#elif defined(CONFIG_MN10300_TTYSM2_TIMER3)
+ scxctr |= SC2CTR_CK_TM3UFLOW_8;
+#else
+#error "Unknown config for ttySM2"
+#endif
+#endif /* CONFIG_AM33_2 */
+ break;
+#endif /* CONFIG_MN10300_TTYSM2 */
+
+ default:
+ break;
+ }
try_alternative:
baud = uart_get_baud_rate(&port->uart, new, old, 0,
@@ -1195,6 +1332,12 @@
ctr &= ~SC2CTR_TWE;
*port->_control = ctr;
}
+
+ /* change Transfer bit-order (LSB/MSB) */
+ if (new->c_cflag & CODMSB)
+ *port->_control |= SC01CTR_OD_MSBFIRST; /* MSB MODE */
+ else
+ *port->_control &= ~SC01CTR_OD_MSBFIRST; /* LSB MODE */
}
/*
@@ -1302,11 +1445,16 @@
printk(KERN_INFO "%s version %s (%s)\n",
serial_name, serial_version, serial_revdate);
-#ifdef CONFIG_MN10300_TTYSM2
- SC2TIM = 8; /* make the baud base of timer 2 IOCLK/8 */
+#if defined(CONFIG_MN10300_TTYSM2) && defined(CONFIG_AM33_2)
+ {
+ int tmp;
+ SC2TIM = 8; /* make the baud base of timer 2 IOCLK/8 */
+ tmp = SC2TIM;
+ }
#endif
- set_intr_stub(EXCEP_IRQ_LEVEL1, mn10300_serial_vdma_interrupt);
+ set_intr_stub(NUM2EXCEP_IRQ_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL),
+ mn10300_serial_vdma_interrupt);
ret = uart_register_driver(&mn10300_serial_driver);
if (!ret) {
@@ -1366,9 +1514,11 @@
port = mn10300_serial_ports[co->index];
/* firstly hijack the serial port from the "virtual DMA" controller */
+ arch_local_cli();
txicr = *port->tx_icr;
- *port->tx_icr = GxICR_LEVEL_1;
+ *port->tx_icr = NUM2GxICR_LEVEL(CONFIG_MN10300_SERIAL_IRQ_LEVEL);
tmp = *port->tx_icr;
+ arch_local_sti();
/* the transmitter may be disabled */
scxctr = *port->_control;
@@ -1422,8 +1572,10 @@
if (!(scxctr & SC01CTR_TXE))
*port->_control = scxctr;
+ arch_local_cli();
*port->tx_icr = txicr;
tmp = *port->tx_icr;
+ arch_local_sti();
}
/*
diff --git a/arch/mn10300/kernel/mn10300-watchdog-low.S b/arch/mn10300/kernel/mn10300-watchdog-low.S
index 9962447..f2f5c9c 100644
--- a/arch/mn10300/kernel/mn10300-watchdog-low.S
+++ b/arch/mn10300/kernel/mn10300-watchdog-low.S
@@ -16,6 +16,7 @@
#include <asm/intctl-regs.h>
#include <asm/timer-regs.h>
#include <asm/frame.inc>
+#include <linux/threads.h>
.text
@@ -53,7 +54,13 @@
.type touch_nmi_watchdog,@function
touch_nmi_watchdog:
clr d0
- mov d0,(watchdog_alert_counter)
+ clr d1
+ mov watchdog_alert_counter, a0
+ setlb
+ mov d0, (a0+)
+ inc d1
+ cmp NR_CPUS, d1
+ lne
ret [],0
.size touch_nmi_watchdog,.-touch_nmi_watchdog
diff --git a/arch/mn10300/kernel/mn10300-watchdog.c b/arch/mn10300/kernel/mn10300-watchdog.c
index f362d9d..965dd61 100644
--- a/arch/mn10300/kernel/mn10300-watchdog.c
+++ b/arch/mn10300/kernel/mn10300-watchdog.c
@@ -30,7 +30,7 @@
static DEFINE_SPINLOCK(watchdog_print_lock);
static unsigned int watchdog;
static unsigned int watchdog_hz = 1;
-unsigned int watchdog_alert_counter;
+unsigned int watchdog_alert_counter[NR_CPUS];
EXPORT_SYMBOL(touch_nmi_watchdog);
@@ -39,9 +39,6 @@
* is to check its timer makes IRQ counts. If they are not
* changing then that CPU has some problem.
*
- * as these watchdog NMI IRQs are generated on every CPU, we only
- * have to check the current processor.
- *
* since NMIs dont listen to _any_ locks, we have to be extremely
* careful not to rely on unsafe variables. The printk might lock
* up though, so we have to break up any console locks first ...
@@ -69,8 +66,8 @@
printk(KERN_INFO "OK.\n");
- /* now that we know it works we can reduce NMI frequency to
- * something more reasonable; makes a difference in some configs
+ /* now that we know it works we can reduce NMI frequency to something
+ * more reasonable; makes a difference in some configs
*/
watchdog_hz = 1;
@@ -121,15 +118,22 @@
}
}
+#ifdef CONFIG_SMP
+static void watchdog_dump_register(void *dummy)
+{
+ printk(KERN_ERR "--- Register Dump (CPU%d) ---\n", CPUID);
+ show_registers(__frame);
+}
+#endif
+
asmlinkage
void watchdog_interrupt(struct pt_regs *regs, enum exception_code excep)
{
-
/*
* Since current-> is always on the stack, and we always switch
* the stack NMI-atomically, it's safe to use smp_processor_id().
*/
- int sum, cpu = smp_processor_id();
+ int sum, cpu;
int irq = NMIIRQ;
u8 wdt, tmp;
@@ -138,43 +142,61 @@
tmp = WDCTR;
NMICR = NMICR_WDIF;
- nmi_count(cpu)++;
+ nmi_count(smp_processor_id())++;
kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
- sum = irq_stat[cpu].__irq_count;
- if (last_irq_sums[cpu] == sum) {
- /*
- * Ayiee, looks like this CPU is stuck ...
- * wait a few IRQs (5 seconds) before doing the oops ...
- */
- watchdog_alert_counter++;
- if (watchdog_alert_counter == 5 * watchdog_hz) {
- spin_lock(&watchdog_print_lock);
- /*
- * We are in trouble anyway, lets at least try
- * to get a message out.
- */
- bust_spinlocks(1);
- printk(KERN_ERR
- "NMI Watchdog detected LOCKUP on CPU%d,"
- " pc %08lx, registers:\n",
- cpu, regs->pc);
- show_registers(regs);
- printk("console shuts up ...\n");
- console_silent();
- spin_unlock(&watchdog_print_lock);
- bust_spinlocks(0);
-#ifdef CONFIG_GDBSTUB
- if (gdbstub_busy)
- gdbstub_exception(regs, excep);
- else
- gdbstub_intercept(regs, excep);
+ for_each_online_cpu(cpu) {
+
+ sum = irq_stat[cpu].__irq_count;
+
+ if ((last_irq_sums[cpu] == sum)
+#if defined(CONFIG_GDBSTUB) && defined(CONFIG_SMP)
+ && !(CHK_GDBSTUB_BUSY()
+ || atomic_read(&cpu_doing_single_step))
#endif
- do_exit(SIGSEGV);
+ ) {
+ /*
+ * Ayiee, looks like this CPU is stuck ...
+ * wait a few IRQs (5 seconds) before doing the oops ...
+ */
+ watchdog_alert_counter[cpu]++;
+ if (watchdog_alert_counter[cpu] == 5 * watchdog_hz) {
+ spin_lock(&watchdog_print_lock);
+ /*
+ * We are in trouble anyway, lets at least try
+ * to get a message out.
+ */
+ bust_spinlocks(1);
+ printk(KERN_ERR
+ "NMI Watchdog detected LOCKUP on CPU%d,"
+ " pc %08lx, registers:\n",
+ cpu, regs->pc);
+#ifdef CONFIG_SMP
+ printk(KERN_ERR
+ "--- Register Dump (CPU%d) ---\n",
+ CPUID);
+#endif
+ show_registers(regs);
+#ifdef CONFIG_SMP
+ smp_nmi_call_function(watchdog_dump_register,
+ NULL, 1);
+#endif
+ printk(KERN_NOTICE "console shuts up ...\n");
+ console_silent();
+ spin_unlock(&watchdog_print_lock);
+ bust_spinlocks(0);
+#ifdef CONFIG_GDBSTUB
+ if (CHK_GDBSTUB_BUSY_AND_ACTIVE())
+ gdbstub_exception(regs, excep);
+ else
+ gdbstub_intercept(regs, excep);
+#endif
+ do_exit(SIGSEGV);
+ }
+ } else {
+ last_irq_sums[cpu] = sum;
+ watchdog_alert_counter[cpu] = 0;
}
- } else {
- last_irq_sums[cpu] = sum;
- watchdog_alert_counter = 0;
}
WDCTR = wdt | WDCTR_WDRST;
diff --git a/arch/mn10300/kernel/process.c b/arch/mn10300/kernel/process.c
index 243e33c..b2e85ed 100644
--- a/arch/mn10300/kernel/process.c
+++ b/arch/mn10300/kernel/process.c
@@ -57,6 +57,7 @@
void (*pm_power_off)(void);
EXPORT_SYMBOL(pm_power_off);
+#if !defined(CONFIG_SMP) || defined(CONFIG_HOTPLUG_CPU)
/*
* we use this if we don't have any better idle routine
*/
@@ -69,6 +70,35 @@
local_irq_enable();
}
+#else /* !CONFIG_SMP || CONFIG_HOTPLUG_CPU */
+/*
+ * On SMP it's slightly faster (but much more power-consuming!)
+ * to poll the ->work.need_resched flag instead of waiting for the
+ * cross-CPU IPI to arrive. Use this option with caution.
+ */
+static inline void poll_idle(void)
+{
+ int oldval;
+
+ local_irq_enable();
+
+ /*
+ * Deal with another CPU just having chosen a thread to
+ * run here:
+ */
+ oldval = test_and_clear_thread_flag(TIF_NEED_RESCHED);
+
+ if (!oldval) {
+ set_thread_flag(TIF_POLLING_NRFLAG);
+ while (!need_resched())
+ cpu_relax();
+ clear_thread_flag(TIF_POLLING_NRFLAG);
+ } else {
+ set_need_resched();
+ }
+}
+#endif /* !CONFIG_SMP || CONFIG_HOTPLUG_CPU */
+
/*
* the idle thread
* - there's no useful work to be done, so just try to conserve power and have
@@ -77,8 +107,6 @@
*/
void cpu_idle(void)
{
- int cpu = smp_processor_id();
-
/* endless idle loop with no priority at all */
for (;;) {
while (!need_resched()) {
@@ -86,8 +114,13 @@
smp_rmb();
idle = pm_idle;
- if (!idle)
+ if (!idle) {
+#if defined(CONFIG_SMP) && !defined(CONFIG_HOTPLUG_CPU)
+ idle = poll_idle;
+#else /* CONFIG_SMP && !CONFIG_HOTPLUG_CPU */
idle = default_idle;
+#endif /* CONFIG_SMP && !CONFIG_HOTPLUG_CPU */
+ }
idle();
}
@@ -233,7 +266,7 @@
}
/* set up things up so the scheduler can start the new task */
- p->thread.__frame = c_kregs;
+ p->thread.frame = c_kregs;
p->thread.a3 = (unsigned long) c_kregs;
p->thread.sp = c_ksp;
p->thread.pc = (unsigned long) ret_from_fork;
diff --git a/arch/mn10300/kernel/profile.c b/arch/mn10300/kernel/profile.c
index 20d7d03..4f342f7 100644
--- a/arch/mn10300/kernel/profile.c
+++ b/arch/mn10300/kernel/profile.c
@@ -41,7 +41,7 @@
tmp = TM11ICR;
printk(KERN_INFO "Profiling initiated on timer 11, priority 0, %uHz\n",
- mn10300_ioclk / 8 / (TM11BR + 1));
+ MN10300_IOCLK / 8 / (TM11BR + 1));
printk(KERN_INFO "Profile histogram stored %p-%p\n",
prof_buffer, (u8 *)(prof_buffer + prof_len) - 1);
diff --git a/arch/mn10300/kernel/rtc.c b/arch/mn10300/kernel/rtc.c
index 4eef0e7..e9e20f9 100644
--- a/arch/mn10300/kernel/rtc.c
+++ b/arch/mn10300/kernel/rtc.c
@@ -20,18 +20,22 @@
DEFINE_SPINLOCK(rtc_lock);
EXPORT_SYMBOL(rtc_lock);
-/* time for RTC to update itself in ioclks */
-static unsigned long mn10300_rtc_update_period;
-
+/*
+ * Read the current RTC time
+ */
void read_persistent_clock(struct timespec *ts)
{
struct rtc_time tm;
get_rtc_time(&tm);
- ts->tv_sec = mktime(tm.tm_year, tm.tm_mon, tm.tm_mday,
- tm.tm_hour, tm.tm_min, tm.tm_sec);
ts->tv_nsec = 0;
+ ts->tv_sec = mktime(tm.tm_year, tm.tm_mon, tm.tm_mday,
+ tm.tm_hour, tm.tm_min, tm.tm_sec);
+
+ /* if rtc is way off in the past, set something reasonable */
+ if (ts->tv_sec < 0)
+ ts->tv_sec = mktime(2009, 1, 1, 12, 0, 0);
}
/*
@@ -115,39 +119,14 @@
*/
void __init calibrate_clock(void)
{
- unsigned long count0, counth, count1;
unsigned char status;
/* make sure the RTC is running and is set to operate in 24hr mode */
status = RTSRC;
RTCRB |= RTCRB_SET;
RTCRB |= RTCRB_TM_24HR;
+ RTCRB &= ~RTCRB_DM_BINARY;
RTCRA |= RTCRA_DVR;
RTCRA &= ~RTCRA_DVR;
RTCRB &= ~RTCRB_SET;
-
- /* work out the clock speed by counting clock cycles between ends of
- * the RTC update cycle - track the RTC through one complete update
- * cycle (1 second)
- */
- startup_timestamp_counter();
-
- while (!(RTCRA & RTCRA_UIP)) {}
- while ((RTCRA & RTCRA_UIP)) {}
-
- count0 = TMTSCBC;
-
- while (!(RTCRA & RTCRA_UIP)) {}
-
- counth = TMTSCBC;
-
- while ((RTCRA & RTCRA_UIP)) {}
-
- count1 = TMTSCBC;
-
- shutdown_timestamp_counter();
-
- MN10300_TSCCLK = count0 - count1; /* the timers count down */
- mn10300_rtc_update_period = counth - count1;
- MN10300_TSC_PER_HZ = MN10300_TSCCLK / HZ;
}
diff --git a/arch/mn10300/kernel/setup.c b/arch/mn10300/kernel/setup.c
index d464aff..1251457 100644
--- a/arch/mn10300/kernel/setup.c
+++ b/arch/mn10300/kernel/setup.c
@@ -22,6 +22,7 @@
#include <linux/init.h>
#include <linux/bootmem.h>
#include <linux/seq_file.h>
+#include <linux/cpu.h>
#include <asm/processor.h>
#include <linux/console.h>
#include <asm/uaccess.h>
@@ -30,7 +31,6 @@
#include <asm/io.h>
#include <asm/smp.h>
#include <proc/proc.h>
-#include <asm/busctl-regs.h>
#include <asm/fpu.h>
#include <asm/sections.h>
@@ -64,11 +64,13 @@
struct thread_info *__current_ti = &init_thread_union.thread_info;
struct task_struct *__current = &init_task;
-#define mn10300_known_cpus 3
+#define mn10300_known_cpus 5
static const char *const mn10300_cputypes[] = {
- "am33v1",
- "am33v2",
- "am34v1",
+ "am33-1",
+ "am33-2",
+ "am34-1",
+ "am33-3",
+ "am34-2",
"unknown"
};
@@ -123,6 +125,7 @@
cpu_init();
unit_setup();
+ smp_init_cpus();
parse_mem_cmdline(cmdline_p);
init_mm.start_code = (unsigned long)&_text;
@@ -179,7 +182,6 @@
void __init cpu_init(void)
{
unsigned long cpurev = CPUREV, type;
- unsigned long base, size;
type = (CPUREV & CPUREV_TYPE) >> CPUREV_TYPE_S;
if (type > mn10300_known_cpus)
@@ -189,47 +191,46 @@
mn10300_cputypes[type],
(cpurev & CPUREV_REVISION) >> CPUREV_REVISION_S);
- /* determine the memory size and base from the memory controller regs */
- memory_size = 0;
-
- base = SDBASE(0);
- if (base & SDBASE_CE) {
- size = (base & SDBASE_CBAM) << SDBASE_CBAM_SHIFT;
- size = ~size + 1;
- base &= SDBASE_CBA;
-
- printk(KERN_INFO "SDRAM[0]: %luMb @%08lx\n", size >> 20, base);
- memory_size += size;
- phys_memory_base = base;
- }
-
- base = SDBASE(1);
- if (base & SDBASE_CE) {
- size = (base & SDBASE_CBAM) << SDBASE_CBAM_SHIFT;
- size = ~size + 1;
- base &= SDBASE_CBA;
-
- printk(KERN_INFO "SDRAM[1]: %luMb @%08lx\n", size >> 20, base);
- memory_size += size;
- if (phys_memory_base == 0)
- phys_memory_base = base;
- }
-
+ get_mem_info(&phys_memory_base, &memory_size);
phys_memory_end = phys_memory_base + memory_size;
-#ifdef CONFIG_FPU
fpu_init_state();
-#endif
}
+static struct cpu cpu_devices[NR_CPUS];
+
+static int __init topology_init(void)
+{
+ int i;
+
+ for_each_present_cpu(i)
+ register_cpu(&cpu_devices[i], i);
+
+ return 0;
+}
+
+subsys_initcall(topology_init);
+
/*
* Get CPU information for use by the procfs.
*/
static int show_cpuinfo(struct seq_file *m, void *v)
{
+#ifdef CONFIG_SMP
+ struct mn10300_cpuinfo *c = v;
+ unsigned long cpu_id = c - cpu_data;
+ unsigned long cpurev = c->type, type, icachesz, dcachesz;
+#else /* CONFIG_SMP */
+ unsigned long cpu_id = 0;
unsigned long cpurev = CPUREV, type, icachesz, dcachesz;
+#endif /* CONFIG_SMP */
- type = (CPUREV & CPUREV_TYPE) >> CPUREV_TYPE_S;
+#ifdef CONFIG_SMP
+ if (!cpu_online(cpu_id))
+ return 0;
+#endif
+
+ type = (cpurev & CPUREV_TYPE) >> CPUREV_TYPE_S;
if (type > mn10300_known_cpus)
type = mn10300_known_cpus;
@@ -244,13 +245,14 @@
1024;
seq_printf(m,
- "processor : 0\n"
+ "processor : %ld\n"
"vendor_id : Matsushita\n"
"cpu core : %s\n"
"cpu rev : %lu\n"
"model name : " PROCESSOR_MODEL_NAME "\n"
"icache size: %lu\n"
"dcache size: %lu\n",
+ cpu_id,
mn10300_cputypes[type],
(cpurev & CPUREV_REVISION) >> CPUREV_REVISION_S,
icachesz,
@@ -262,8 +264,13 @@
"bogomips : %lu.%02lu\n\n",
MN10300_IOCLK / 1000000,
(MN10300_IOCLK / 10000) % 100,
+#ifdef CONFIG_SMP
+ c->loops_per_jiffy / (500000 / HZ),
+ (c->loops_per_jiffy / (5000 / HZ)) % 100
+#else /* CONFIG_SMP */
loops_per_jiffy / (500000 / HZ),
(loops_per_jiffy / (5000 / HZ)) % 100
+#endif /* CONFIG_SMP */
);
return 0;
diff --git a/arch/mn10300/kernel/smp-low.S b/arch/mn10300/kernel/smp-low.S
new file mode 100644
index 0000000..72938ce
--- /dev/null
+++ b/arch/mn10300/kernel/smp-low.S
@@ -0,0 +1,97 @@
+/* SMP IPI low-level handler
+ *
+ * Copyright (C) 2006-2007 Matsushita Electric Industrial Co., Ltd.
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ */
+
+#include <linux/sys.h>
+#include <linux/linkage.h>
+#include <asm/smp.h>
+#include <asm/system.h>
+#include <asm/thread_info.h>
+#include <asm/cpu-regs.h>
+#include <proc/smp-regs.h>
+#include <asm/asm-offsets.h>
+#include <asm/frame.inc>
+
+ .am33_2
+
+###############################################################################
+#
+# IPI interrupt handler
+#
+###############################################################################
+ .globl mn10300_low_ipi_handler
+mn10300_low_ipi_handler:
+ add -4,sp
+ mov d0,(sp)
+ movhu (IAGR),d0
+ and IAGR_GN,d0
+ lsr 0x2,d0
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+ cmp FLUSH_CACHE_IPI,d0
+ beq mn10300_flush_cache_ipi
+#endif
+ cmp SMP_BOOT_IRQ,d0
+ beq mn10300_smp_boot_ipi
+ /* OTHERS */
+ mov (sp),d0
+ add 4,sp
+#ifdef CONFIG_GDBSTUB
+ jmp gdbstub_io_rx_handler
+#else
+ jmp end
+#endif
+
+###############################################################################
+#
+# Cache flush IPI interrupt handler
+#
+###############################################################################
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+mn10300_flush_cache_ipi:
+ mov (sp),d0
+ add 4,sp
+
+ /* FLUSH_CACHE_IPI */
+ add -4,sp
+ SAVE_ALL
+ mov GxICR_DETECT,d2
+ movbu d2,(GxICR(FLUSH_CACHE_IPI)) # ACK the interrupt
+ movhu (GxICR(FLUSH_CACHE_IPI)),d2
+ call smp_cache_interrupt[],0
+ RESTORE_ALL
+ jmp end
+#endif
+
+###############################################################################
+#
+# SMP boot CPU IPI interrupt handler
+#
+###############################################################################
+mn10300_smp_boot_ipi:
+ /* clear interrupt */
+ movhu (GxICR(SMP_BOOT_IRQ)),d0
+ and ~GxICR_REQUEST,d0
+ movhu d0,(GxICR(SMP_BOOT_IRQ))
+ mov (sp),d0
+ add 4,sp
+
+ # get stack
+ mov (CPUID),a0
+ add -1,a0
+ add a0,a0
+ add a0,a0
+ mov (start_stack,a0),a0
+ mov a0,sp
+ jmp initialize_secondary
+
+
+# Jump here after RTI to suppress the icache lookahead
+end:
diff --git a/arch/mn10300/kernel/smp.c b/arch/mn10300/kernel/smp.c
new file mode 100644
index 0000000..b80234c
--- /dev/null
+++ b/arch/mn10300/kernel/smp.c
@@ -0,0 +1,1141 @@
+/* SMP support routines.
+ *
+ * Copyright (C) 2006-2008 Panasonic Corporation
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/init.h>
+#include <linux/jiffies.h>
+#include <linux/cpumask.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/profile.h>
+#include <linux/smp.h>
+#include <asm/tlbflush.h>
+#include <asm/system.h>
+#include <asm/bitops.h>
+#include <asm/processor.h>
+#include <asm/bug.h>
+#include <asm/exceptions.h>
+#include <asm/hardirq.h>
+#include <asm/fpu.h>
+#include <asm/mmu_context.h>
+#include <asm/thread_info.h>
+#include <asm/cpu-regs.h>
+#include <asm/intctl-regs.h>
+#include "internal.h"
+
+#ifdef CONFIG_HOTPLUG_CPU
+#include <linux/cpu.h>
+#include <asm/cacheflush.h>
+
+static unsigned long sleep_mode[NR_CPUS];
+
+static void run_sleep_cpu(unsigned int cpu);
+static void run_wakeup_cpu(unsigned int cpu);
+#endif /* CONFIG_HOTPLUG_CPU */
+
+/*
+ * Debug Message function
+ */
+
+#undef DEBUG_SMP
+#ifdef DEBUG_SMP
+#define Dprintk(fmt, ...) printk(KERN_DEBUG fmt, ##__VA_ARGS__)
+#else
+#define Dprintk(fmt, ...) no_printk(KERN_DEBUG fmt, ##__VA_ARGS__)
+#endif
+
+/* timeout value in msec for smp_nmi_call_function. zero is no timeout. */
+#define CALL_FUNCTION_NMI_IPI_TIMEOUT 0
+
+/*
+ * Structure and data for smp_nmi_call_function().
+ */
+struct nmi_call_data_struct {
+ smp_call_func_t func;
+ void *info;
+ cpumask_t started;
+ cpumask_t finished;
+ int wait;
+ char size_alignment[0]
+ __attribute__ ((__aligned__(SMP_CACHE_BYTES)));
+} __attribute__ ((__aligned__(SMP_CACHE_BYTES)));
+
+static DEFINE_SPINLOCK(smp_nmi_call_lock);
+static struct nmi_call_data_struct *nmi_call_data;
+
+/*
+ * Data structures and variables
+ */
+static cpumask_t cpu_callin_map; /* Bitmask of callin CPUs */
+static cpumask_t cpu_callout_map; /* Bitmask of callout CPUs */
+cpumask_t cpu_boot_map; /* Bitmask of boot APs */
+unsigned long start_stack[NR_CPUS - 1];
+
+/*
+ * Per CPU parameters
+ */
+struct mn10300_cpuinfo cpu_data[NR_CPUS] __cacheline_aligned;
+
+static int cpucount; /* The count of boot CPUs */
+static cpumask_t smp_commenced_mask;
+cpumask_t cpu_initialized __initdata = CPU_MASK_NONE;
+
+/*
+ * Function Prototypes
+ */
+static int do_boot_cpu(int);
+static void smp_show_cpu_info(int cpu_id);
+static void smp_callin(void);
+static void smp_online(void);
+static void smp_store_cpu_info(int);
+static void smp_cpu_init(void);
+static void smp_tune_scheduling(void);
+static void send_IPI_mask(const cpumask_t *cpumask, int irq);
+static void init_ipi(void);
+
+/*
+ * IPI Initialization interrupt definitions
+ */
+static void mn10300_ipi_disable(unsigned int irq);
+static void mn10300_ipi_enable(unsigned int irq);
+static void mn10300_ipi_ack(unsigned int irq);
+static void mn10300_ipi_nop(unsigned int irq);
+
+static struct irq_chip mn10300_ipi_type = {
+ .name = "cpu_ipi",
+ .disable = mn10300_ipi_disable,
+ .enable = mn10300_ipi_enable,
+ .ack = mn10300_ipi_ack,
+ .eoi = mn10300_ipi_nop
+};
+
+static irqreturn_t smp_reschedule_interrupt(int irq, void *dev_id);
+static irqreturn_t smp_call_function_interrupt(int irq, void *dev_id);
+static irqreturn_t smp_ipi_timer_interrupt(int irq, void *dev_id);
+
+static struct irqaction reschedule_ipi = {
+ .handler = smp_reschedule_interrupt,
+ .name = "smp reschedule IPI"
+};
+static struct irqaction call_function_ipi = {
+ .handler = smp_call_function_interrupt,
+ .name = "smp call function IPI"
+};
+static struct irqaction local_timer_ipi = {
+ .handler = smp_ipi_timer_interrupt,
+ .flags = IRQF_DISABLED,
+ .name = "smp local timer IPI"
+};
+
+/**
+ * init_ipi - Initialise the IPI mechanism
+ */
+static void init_ipi(void)
+{
+ unsigned long flags;
+ u16 tmp16;
+
+ /* set up the reschedule IPI */
+ set_irq_chip_and_handler(RESCHEDULE_IPI,
+ &mn10300_ipi_type, handle_percpu_irq);
+ setup_irq(RESCHEDULE_IPI, &reschedule_ipi);
+ set_intr_level(RESCHEDULE_IPI, RESCHEDULE_GxICR_LV);
+ mn10300_ipi_enable(RESCHEDULE_IPI);
+
+ /* set up the call function IPI */
+ set_irq_chip_and_handler(CALL_FUNC_SINGLE_IPI,
+ &mn10300_ipi_type, handle_percpu_irq);
+ setup_irq(CALL_FUNC_SINGLE_IPI, &call_function_ipi);
+ set_intr_level(CALL_FUNC_SINGLE_IPI, CALL_FUNCTION_GxICR_LV);
+ mn10300_ipi_enable(CALL_FUNC_SINGLE_IPI);
+
+ /* set up the local timer IPI */
+ set_irq_chip_and_handler(LOCAL_TIMER_IPI,
+ &mn10300_ipi_type, handle_percpu_irq);
+ setup_irq(LOCAL_TIMER_IPI, &local_timer_ipi);
+ set_intr_level(LOCAL_TIMER_IPI, LOCAL_TIMER_GxICR_LV);
+ mn10300_ipi_enable(LOCAL_TIMER_IPI);
+
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+ /* set up the cache flush IPI */
+ flags = arch_local_cli_save();
+ __set_intr_stub(NUM2EXCEP_IRQ_LEVEL(FLUSH_CACHE_GxICR_LV),
+ mn10300_low_ipi_handler);
+ GxICR(FLUSH_CACHE_IPI) = FLUSH_CACHE_GxICR_LV | GxICR_DETECT;
+ mn10300_ipi_enable(FLUSH_CACHE_IPI);
+ arch_local_irq_restore(flags);
+#endif
+
+ /* set up the NMI call function IPI */
+ flags = arch_local_cli_save();
+ GxICR(CALL_FUNCTION_NMI_IPI) = GxICR_NMI | GxICR_ENABLE | GxICR_DETECT;
+ tmp16 = GxICR(CALL_FUNCTION_NMI_IPI);
+ arch_local_irq_restore(flags);
+
+ /* set up the SMP boot IPI */
+ flags = arch_local_cli_save();
+ __set_intr_stub(NUM2EXCEP_IRQ_LEVEL(SMP_BOOT_GxICR_LV),
+ mn10300_low_ipi_handler);
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * mn10300_ipi_shutdown - Shut down handling of an IPI
+ * @irq: The IPI to be shut down.
+ */
+static void mn10300_ipi_shutdown(unsigned int irq)
+{
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_DETECT;
+ tmp = GxICR(irq);
+
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * mn10300_ipi_enable - Enable an IPI
+ * @irq: The IPI to be enabled.
+ */
+static void mn10300_ipi_enable(unsigned int irq)
+{
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+
+ tmp = GxICR(irq);
+ GxICR(irq) = (tmp & GxICR_LEVEL) | GxICR_ENABLE;
+ tmp = GxICR(irq);
+
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * mn10300_ipi_disable - Disable an IPI
+ * @irq: The IPI to be disabled.
+ */
+static void mn10300_ipi_disable(unsigned int irq)
+{
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+
+ tmp = GxICR(irq);
+ GxICR(irq) = tmp & GxICR_LEVEL;
+ tmp = GxICR(irq);
+
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * mn10300_ipi_ack - Acknowledge an IPI interrupt in the PIC
+ * @irq: The IPI to be acknowledged.
+ *
+ * Clear the interrupt detection flag for the IPI on the appropriate interrupt
+ * channel in the PIC.
+ */
+static void mn10300_ipi_ack(unsigned int irq)
+{
+ unsigned long flags;
+ u16 tmp;
+
+ flags = arch_local_cli_save();
+ GxICR_u8(irq) = GxICR_DETECT;
+ tmp = GxICR(irq);
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * mn10300_ipi_nop - Dummy IPI action
+ * @irq: The IPI to be acted upon.
+ */
+static void mn10300_ipi_nop(unsigned int irq)
+{
+}
+
+/**
+ * send_IPI_mask - Send IPIs to all CPUs in list
+ * @cpumask: The list of CPUs to target.
+ * @irq: The IPI request to be sent.
+ *
+ * Send the specified IPI to all the CPUs in the list, not waiting for them to
+ * finish before returning. The caller is responsible for synchronisation if
+ * that is needed.
+ */
+static void send_IPI_mask(const cpumask_t *cpumask, int irq)
+{
+ int i;
+ u16 tmp;
+
+ for (i = 0; i < NR_CPUS; i++) {
+ if (cpu_isset(i, *cpumask)) {
+ /* send IPI */
+ tmp = CROSS_GxICR(irq, i);
+ CROSS_GxICR(irq, i) =
+ tmp | GxICR_REQUEST | GxICR_DETECT;
+ tmp = CROSS_GxICR(irq, i); /* flush write buffer */
+ }
+ }
+}
+
+/**
+ * send_IPI_self - Send an IPI to this CPU.
+ * @irq: The IPI request to be sent.
+ *
+ * Send the specified IPI to the current CPU.
+ */
+void send_IPI_self(int irq)
+{
+ send_IPI_mask(cpumask_of(smp_processor_id()), irq);
+}
+
+/**
+ * send_IPI_allbutself - Send IPIs to all the other CPUs.
+ * @irq: The IPI request to be sent.
+ *
+ * Send the specified IPI to all CPUs in the system barring the current one,
+ * not waiting for them to finish before returning. The caller is responsible
+ * for synchronisation if that is needed.
+ */
+void send_IPI_allbutself(int irq)
+{
+ cpumask_t cpumask;
+
+ cpumask = cpu_online_map;
+ cpu_clear(smp_processor_id(), cpumask);
+ send_IPI_mask(&cpumask, irq);
+}
+
+void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+ BUG();
+ /*send_IPI_mask(mask, CALL_FUNCTION_IPI);*/
+}
+
+void arch_send_call_function_single_ipi(int cpu)
+{
+ send_IPI_mask(cpumask_of(cpu), CALL_FUNC_SINGLE_IPI);
+}
+
+/**
+ * smp_send_reschedule - Send reschedule IPI to a CPU
+ * @cpu: The CPU to target.
+ */
+void smp_send_reschedule(int cpu)
+{
+ send_IPI_mask(cpumask_of(cpu), RESCHEDULE_IPI);
+}
+
+/**
+ * smp_nmi_call_function - Send a call function NMI IPI to all CPUs
+ * @func: The function to ask to be run.
+ * @info: The context data to pass to that function.
+ * @wait: If true, wait (atomically) until function is run on all CPUs.
+ *
+ * Send a non-maskable request to all CPUs in the system, requesting them to
+ * run the specified function with the given context data, and, potentially, to
+ * wait for completion of that function on all CPUs.
+ *
+ * Returns 0 if successful, -ETIMEDOUT if we were asked to wait, but hit the
+ * timeout.
+ */
+int smp_nmi_call_function(smp_call_func_t func, void *info, int wait)
+{
+ struct nmi_call_data_struct data;
+ unsigned long flags;
+ unsigned int cnt;
+ int cpus, ret = 0;
+
+ cpus = num_online_cpus() - 1;
+ if (cpus < 1)
+ return 0;
+
+ data.func = func;
+ data.info = info;
+ data.started = cpu_online_map;
+ cpu_clear(smp_processor_id(), data.started);
+ data.wait = wait;
+ if (wait)
+ data.finished = data.started;
+
+ spin_lock_irqsave(&smp_nmi_call_lock, flags);
+ nmi_call_data = &data;
+ smp_mb();
+
+ /* Send a message to all other CPUs and wait for them to respond */
+ send_IPI_allbutself(CALL_FUNCTION_NMI_IPI);
+
+ /* Wait for response */
+ if (CALL_FUNCTION_NMI_IPI_TIMEOUT > 0) {
+ for (cnt = 0;
+ cnt < CALL_FUNCTION_NMI_IPI_TIMEOUT &&
+ !cpus_empty(data.started);
+ cnt++)
+ mdelay(1);
+
+ if (wait && cnt < CALL_FUNCTION_NMI_IPI_TIMEOUT) {
+ for (cnt = 0;
+ cnt < CALL_FUNCTION_NMI_IPI_TIMEOUT &&
+ !cpus_empty(data.finished);
+ cnt++)
+ mdelay(1);
+ }
+
+ if (cnt >= CALL_FUNCTION_NMI_IPI_TIMEOUT)
+ ret = -ETIMEDOUT;
+
+ } else {
+ /* If timeout value is zero, wait until cpumask has been
+ * cleared */
+ while (!cpus_empty(data.started))
+ barrier();
+ if (wait)
+ while (!cpus_empty(data.finished))
+ barrier();
+ }
+
+ spin_unlock_irqrestore(&smp_nmi_call_lock, flags);
+ return ret;
+}
+
+/**
+ * stop_this_cpu - Callback to stop a CPU.
+ * @unused: Callback context (ignored).
+ */
+void stop_this_cpu(void *unused)
+{
+ static volatile int stopflag;
+ unsigned long flags;
+
+#ifdef CONFIG_GDBSTUB
+ /* In case of single stepping smp_send_stop by other CPU,
+ * clear procindebug to avoid deadlock.
+ */
+ atomic_set(&procindebug[smp_processor_id()], 0);
+#endif /* CONFIG_GDBSTUB */
+
+ flags = arch_local_cli_save();
+ cpu_clear(smp_processor_id(), cpu_online_map);
+
+ while (!stopflag)
+ cpu_relax();
+
+ cpu_set(smp_processor_id(), cpu_online_map);
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * smp_send_stop - Send a stop request to all CPUs.
+ */
+void smp_send_stop(void)
+{
+ smp_nmi_call_function(stop_this_cpu, NULL, 0);
+}
+
+/**
+ * smp_reschedule_interrupt - Reschedule IPI handler
+ * @irq: The interrupt number.
+ * @dev_id: The device ID.
+ *
+ * We need do nothing here, since the scheduling will be effected on our way
+ * back through entry.S.
+ *
+ * Returns IRQ_HANDLED to indicate we handled the interrupt successfully.
+ */
+static irqreturn_t smp_reschedule_interrupt(int irq, void *dev_id)
+{
+ /* do nothing */
+ return IRQ_HANDLED;
+}
+
+/**
+ * smp_call_function_interrupt - Call function IPI handler
+ * @irq: The interrupt number.
+ * @dev_id: The device ID.
+ *
+ * Returns IRQ_HANDLED to indicate we handled the interrupt successfully.
+ */
+static irqreturn_t smp_call_function_interrupt(int irq, void *dev_id)
+{
+ /* generic_smp_call_function_interrupt(); */
+ generic_smp_call_function_single_interrupt();
+ return IRQ_HANDLED;
+}
+
+/**
+ * smp_nmi_call_function_interrupt - Non-maskable call function IPI handler
+ */
+void smp_nmi_call_function_interrupt(void)
+{
+ smp_call_func_t func = nmi_call_data->func;
+ void *info = nmi_call_data->info;
+ int wait = nmi_call_data->wait;
+
+ /* Notify the initiating CPU that I've grabbed the data and am about to
+ * execute the function
+ */
+ smp_mb();
+ cpu_clear(smp_processor_id(), nmi_call_data->started);
+ (*func)(info);
+
+ if (wait) {
+ smp_mb();
+ cpu_clear(smp_processor_id(), nmi_call_data->finished);
+ }
+}
+
+/**
+ * smp_ipi_timer_interrupt - Local timer IPI handler
+ * @irq: The interrupt number.
+ * @dev_id: The device ID.
+ *
+ * Returns IRQ_HANDLED to indicate we handled the interrupt successfully.
+ */
+static irqreturn_t smp_ipi_timer_interrupt(int irq, void *dev_id)
+{
+ return local_timer_interrupt();
+}
+
+void __init smp_init_cpus(void)
+{
+ int i;
+ for (i = 0; i < NR_CPUS; i++) {
+ set_cpu_possible(i, true);
+ set_cpu_present(i, true);
+ }
+}
+
+/**
+ * smp_cpu_init - Initialise AP in start_secondary.
+ *
+ * For this Application Processor, set up init_mm, initialise FPU and set
+ * interrupt level 0-6 setting.
+ */
+static void __init smp_cpu_init(void)
+{
+ unsigned long flags;
+ int cpu_id = smp_processor_id();
+ u16 tmp16;
+
+ if (test_and_set_bit(cpu_id, &cpu_initialized)) {
+ printk(KERN_WARNING "CPU#%d already initialized!\n", cpu_id);
+ for (;;)
+ local_irq_enable();
+ }
+ printk(KERN_INFO "Initializing CPU#%d\n", cpu_id);
+
+ atomic_inc(&init_mm.mm_count);
+ current->active_mm = &init_mm;
+ BUG_ON(current->mm);
+
+ enter_lazy_tlb(&init_mm, current);
+
+ /* Force FPU initialization */
+ clear_using_fpu(current);
+
+ GxICR(CALL_FUNC_SINGLE_IPI) = CALL_FUNCTION_GxICR_LV | GxICR_DETECT;
+ mn10300_ipi_enable(CALL_FUNC_SINGLE_IPI);
+
+ GxICR(LOCAL_TIMER_IPI) = LOCAL_TIMER_GxICR_LV | GxICR_DETECT;
+ mn10300_ipi_enable(LOCAL_TIMER_IPI);
+
+ GxICR(RESCHEDULE_IPI) = RESCHEDULE_GxICR_LV | GxICR_DETECT;
+ mn10300_ipi_enable(RESCHEDULE_IPI);
+
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+ GxICR(FLUSH_CACHE_IPI) = FLUSH_CACHE_GxICR_LV | GxICR_DETECT;
+ mn10300_ipi_enable(FLUSH_CACHE_IPI);
+#endif
+
+ mn10300_ipi_shutdown(SMP_BOOT_IRQ);
+
+ /* Set up the non-maskable call function IPI */
+ flags = arch_local_cli_save();
+ GxICR(CALL_FUNCTION_NMI_IPI) = GxICR_NMI | GxICR_ENABLE | GxICR_DETECT;
+ tmp16 = GxICR(CALL_FUNCTION_NMI_IPI);
+ arch_local_irq_restore(flags);
+}
+
+/**
+ * smp_prepare_cpu_init - Initialise CPU in startup_secondary
+ *
+ * Set interrupt level 0-6 setting and init ICR of gdbstub.
+ */
+void smp_prepare_cpu_init(void)
+{
+ int loop;
+
+ /* Set the interrupt vector registers */
+ IVAR0 = EXCEP_IRQ_LEVEL0;
+ IVAR1 = EXCEP_IRQ_LEVEL1;
+ IVAR2 = EXCEP_IRQ_LEVEL2;
+ IVAR3 = EXCEP_IRQ_LEVEL3;
+ IVAR4 = EXCEP_IRQ_LEVEL4;
+ IVAR5 = EXCEP_IRQ_LEVEL5;
+ IVAR6 = EXCEP_IRQ_LEVEL6;
+
+ /* Disable all interrupts and set to priority 6 (lowest) */
+ for (loop = 0; loop < GxICR_NUM_IRQS; loop++)
+ GxICR(loop) = GxICR_LEVEL_6 | GxICR_DETECT;
+
+#ifdef CONFIG_GDBSTUB
+ /* initialise GDB-stub */
+ do {
+ unsigned long flags;
+ u16 tmp16;
+
+ flags = arch_local_cli_save();
+ GxICR(GDB_NMI_IPI) = GxICR_NMI | GxICR_ENABLE | GxICR_DETECT;
+ tmp16 = GxICR(GDB_NMI_IPI);
+ arch_local_irq_restore(flags);
+ } while (0);
+#endif
+}
+
+/**
+ * start_secondary - Activate a secondary CPU (AP)
+ * @unused: Thread parameter (ignored).
+ */
+int __init start_secondary(void *unused)
+{
+ smp_cpu_init();
+
+ smp_callin();
+ while (!cpu_isset(smp_processor_id(), smp_commenced_mask))
+ cpu_relax();
+
+ local_flush_tlb();
+ preempt_disable();
+ smp_online();
+
+ cpu_idle();
+ return 0;
+}
+
+/**
+ * smp_prepare_cpus - Boot up secondary CPUs (APs)
+ * @max_cpus: Maximum number of CPUs to boot.
+ *
+ * Call do_boot_cpu, and boot up APs.
+ */
+void __init smp_prepare_cpus(unsigned int max_cpus)
+{
+ int phy_id;
+
+ /* Setup boot CPU information */
+ smp_store_cpu_info(0);
+ smp_tune_scheduling();
+
+ init_ipi();
+
+ /* If SMP should be disabled, then finish */
+ if (max_cpus == 0) {
+ printk(KERN_INFO "SMP mode deactivated.\n");
+ goto smp_done;
+ }
+
+ /* Boot secondary CPUs (for which phy_id > 0) */
+ for (phy_id = 0; phy_id < NR_CPUS; phy_id++) {
+ /* Don't boot primary CPU */
+ if (max_cpus <= cpucount + 1)
+ continue;
+ if (phy_id != 0)
+ do_boot_cpu(phy_id);
+ set_cpu_possible(phy_id, true);
+ smp_show_cpu_info(phy_id);
+ }
+
+smp_done:
+ Dprintk("Boot done.\n");
+}
+
+/**
+ * smp_store_cpu_info - Save a CPU's information
+ * @cpu: The CPU to save for.
+ *
+ * Save boot_cpu_data and jiffy for the specified CPU.
+ */
+static void __init smp_store_cpu_info(int cpu)
+{
+ struct mn10300_cpuinfo *ci = &cpu_data[cpu];
+
+ *ci = boot_cpu_data;
+ ci->loops_per_jiffy = loops_per_jiffy;
+ ci->type = CPUREV;
+}
+
+/**
+ * smp_tune_scheduling - Set time slice value
+ *
+ * Nothing to do here.
+ */
+static void __init smp_tune_scheduling(void)
+{
+}
+
+/**
+ * do_boot_cpu: Boot up one CPU
+ * @phy_id: Physical ID of CPU to boot.
+ *
+ * Send an IPI to a secondary CPU to boot it. Returns 0 on success, 1
+ * otherwise.
+ */
+static int __init do_boot_cpu(int phy_id)
+{
+ struct task_struct *idle;
+ unsigned long send_status, callin_status;
+ int timeout, cpu_id;
+
+ send_status = GxICR_REQUEST;
+ callin_status = 0;
+ timeout = 0;
+ cpu_id = phy_id;
+
+ cpucount++;
+
+ /* Create idle thread for this CPU */
+ idle = fork_idle(cpu_id);
+ if (IS_ERR(idle))
+ panic("Failed fork for CPU#%d.", cpu_id);
+
+ idle->thread.pc = (unsigned long)start_secondary;
+
+ printk(KERN_NOTICE "Booting CPU#%d\n", cpu_id);
+ start_stack[cpu_id - 1] = idle->thread.sp;
+
+ task_thread_info(idle)->cpu = cpu_id;
+
+ /* Send boot IPI to AP */
+ send_IPI_mask(cpumask_of(phy_id), SMP_BOOT_IRQ);
+
+ Dprintk("Waiting for send to finish...\n");
+
+ /* Wait for AP's IPI receive in 100[ms] */
+ do {
+ udelay(1000);
+ send_status =
+ CROSS_GxICR(SMP_BOOT_IRQ, phy_id) & GxICR_REQUEST;
+ } while (send_status == GxICR_REQUEST && timeout++ < 100);
+
+ Dprintk("Waiting for cpu_callin_map.\n");
+
+ if (send_status == 0) {
+ /* Allow AP to start initializing */
+ cpu_set(cpu_id, cpu_callout_map);
+
+ /* Wait for setting cpu_callin_map */
+ timeout = 0;
+ do {
+ udelay(1000);
+ callin_status = cpu_isset(cpu_id, cpu_callin_map);
+ } while (callin_status == 0 && timeout++ < 5000);
+
+ if (callin_status == 0)
+ Dprintk("Not responding.\n");
+ } else {
+ printk(KERN_WARNING "IPI not delivered.\n");
+ }
+
+ if (send_status == GxICR_REQUEST || callin_status == 0) {
+ cpu_clear(cpu_id, cpu_callout_map);
+ cpu_clear(cpu_id, cpu_callin_map);
+ cpu_clear(cpu_id, cpu_initialized);
+ cpucount--;
+ return 1;
+ }
+ return 0;
+}
+
+/**
+ * smp_show_cpu_info - Show SMP CPU information
+ * @cpu: The CPU of interest.
+ */
+static void __init smp_show_cpu_info(int cpu)
+{
+ struct mn10300_cpuinfo *ci = &cpu_data[cpu];
+
+ printk(KERN_INFO
+ "CPU#%d : ioclk speed: %lu.%02luMHz : bogomips : %lu.%02lu\n",
+ cpu,
+ MN10300_IOCLK / 1000000,
+ (MN10300_IOCLK / 10000) % 100,
+ ci->loops_per_jiffy / (500000 / HZ),
+ (ci->loops_per_jiffy / (5000 / HZ)) % 100);
+}
+
+/**
+ * smp_callin - Set cpu_callin_map of the current CPU ID
+ */
+static void __init smp_callin(void)
+{
+ unsigned long timeout;
+ int cpu;
+
+ cpu = smp_processor_id();
+ timeout = jiffies + (2 * HZ);
+
+ if (cpu_isset(cpu, cpu_callin_map)) {
+ printk(KERN_ERR "CPU#%d already present.\n", cpu);
+ BUG();
+ }
+ Dprintk("CPU#%d waiting for CALLOUT\n", cpu);
+
+ /* Wait for AP startup 2s total */
+ while (time_before(jiffies, timeout)) {
+ if (cpu_isset(cpu, cpu_callout_map))
+ break;
+ cpu_relax();
+ }
+
+ if (!time_before(jiffies, timeout)) {
+ printk(KERN_ERR
+ "BUG: CPU#%d started up but did not get a callout!\n",
+ cpu);
+ BUG();
+ }
+
+#ifdef CONFIG_CALIBRATE_DELAY
+ calibrate_delay(); /* Get our bogomips */
+#endif
+
+ /* Save our processor parameters */
+ smp_store_cpu_info(cpu);
+
+ /* Allow the boot processor to continue */
+ cpu_set(cpu, cpu_callin_map);
+}
+
+/**
+ * smp_online - Set cpu_online_map
+ */
+static void __init smp_online(void)
+{
+ int cpu;
+
+ cpu = smp_processor_id();
+
+ local_irq_enable();
+
+ cpu_set(cpu, cpu_online_map);
+ smp_wmb();
+}
+
+/**
+ * smp_cpus_done -
+ * @max_cpus: Maximum CPU count.
+ *
+ * Do nothing.
+ */
+void __init smp_cpus_done(unsigned int max_cpus)
+{
+}
+
+/*
+ * smp_prepare_boot_cpu - Set up stuff for the boot processor.
+ *
+ * Set up the cpu_online_map, cpu_callout_map and cpu_callin_map of the boot
+ * processor (CPU 0).
+ */
+void __devinit smp_prepare_boot_cpu(void)
+{
+ cpu_set(0, cpu_callout_map);
+ cpu_set(0, cpu_callin_map);
+ current_thread_info()->cpu = 0;
+}
+
+/*
+ * initialize_secondary - Initialise a secondary CPU (Application Processor).
+ *
+ * Set SP register and jump to thread's PC address.
+ */
+void initialize_secondary(void)
+{
+ asm volatile (
+ "mov %0,sp \n"
+ "jmp (%1) \n"
+ :
+ : "a"(current->thread.sp), "a"(current->thread.pc));
+}
+
+/**
+ * __cpu_up - Set smp_commenced_mask for the nominated CPU
+ * @cpu: The target CPU.
+ */
+int __devinit __cpu_up(unsigned int cpu)
+{
+ int timeout;
+
+#ifdef CONFIG_HOTPLUG_CPU
+ if (num_online_cpus() == 1)
+ disable_hlt();
+ if (sleep_mode[cpu])
+ run_wakeup_cpu(cpu);
+#endif /* CONFIG_HOTPLUG_CPU */
+
+ cpu_set(cpu, smp_commenced_mask);
+
+ /* Wait 5s total for a response */
+ for (timeout = 0 ; timeout < 5000 ; timeout++) {
+ if (cpu_isset(cpu, cpu_online_map))
+ break;
+ udelay(1000);
+ }
+
+ BUG_ON(!cpu_isset(cpu, cpu_online_map));
+ return 0;
+}
+
+/**
+ * setup_profiling_timer - Set up the profiling timer
+ * @multiplier - The frequency multiplier to use
+ *
+ * The frequency of the profiling timer can be changed by writing a multiplier
+ * value into /proc/profile.
+ */
+int setup_profiling_timer(unsigned int multiplier)
+{
+ return -EINVAL;
+}
+
+/*
+ * CPU hotplug routines
+ */
+#ifdef CONFIG_HOTPLUG_CPU
+
+static DEFINE_PER_CPU(struct cpu, cpu_devices);
+
+static int __init topology_init(void)
+{
+ int cpu, ret;
+
+ for_each_cpu(cpu) {
+ ret = register_cpu(&per_cpu(cpu_devices, cpu), cpu, NULL);
+ if (ret)
+ printk(KERN_WARNING
+ "topology_init: register_cpu %d failed (%d)\n",
+ cpu, ret);
+ }
+ return 0;
+}
+
+subsys_initcall(topology_init);
+
+int __cpu_disable(void)
+{
+ int cpu = smp_processor_id();
+ if (cpu == 0)
+ return -EBUSY;
+
+ migrate_irqs();
+ cpu_clear(cpu, current->active_mm->cpu_vm_mask);
+ return 0;
+}
+
+void __cpu_die(unsigned int cpu)
+{
+ run_sleep_cpu(cpu);
+
+ if (num_online_cpus() == 1)
+ enable_hlt();
+}
+
+#ifdef CONFIG_MN10300_CACHE_ENABLED
+static inline void hotplug_cpu_disable_cache(void)
+{
+ int tmp;
+ asm volatile(
+ " movhu (%1),%0 \n"
+ " and %2,%0 \n"
+ " movhu %0,(%1) \n"
+ "1: movhu (%1),%0 \n"
+ " btst %3,%0 \n"
+ " bne 1b \n"
+ : "=&r"(tmp)
+ : "a"(&CHCTR),
+ "i"(~(CHCTR_ICEN | CHCTR_DCEN)),
+ "i"(CHCTR_ICBUSY | CHCTR_DCBUSY)
+ : "memory", "cc");
+}
+
+static inline void hotplug_cpu_enable_cache(void)
+{
+ int tmp;
+ asm volatile(
+ "movhu (%1),%0 \n"
+ "or %2,%0 \n"
+ "movhu %0,(%1) \n"
+ : "=&r"(tmp)
+ : "a"(&CHCTR),
+ "i"(CHCTR_ICEN | CHCTR_DCEN)
+ : "memory", "cc");
+}
+
+static inline void hotplug_cpu_invalidate_cache(void)
+{
+ int tmp;
+ asm volatile (
+ "movhu (%1),%0 \n"
+ "or %2,%0 \n"
+ "movhu %0,(%1) \n"
+ : "=&r"(tmp)
+ : "a"(&CHCTR),
+ "i"(CHCTR_ICINV | CHCTR_DCINV)
+ : "cc");
+}
+
+#else /* CONFIG_MN10300_CACHE_ENABLED */
+#define hotplug_cpu_disable_cache() do {} while (0)
+#define hotplug_cpu_enable_cache() do {} while (0)
+#define hotplug_cpu_invalidate_cache() do {} while (0)
+#endif /* CONFIG_MN10300_CACHE_ENABLED */
+
+/**
+ * hotplug_cpu_nmi_call_function - Call a function on other CPUs for hotplug
+ * @cpumask: List of target CPUs.
+ * @func: The function to call on those CPUs.
+ * @info: The context data for the function to be called.
+ * @wait: Whether to wait for the calls to complete.
+ *
+ * Non-maskably call a function on another CPU for hotplug purposes.
+ *
+ * This function must be called with maskable interrupts disabled.
+ */
+static int hotplug_cpu_nmi_call_function(cpumask_t cpumask,
+ smp_call_func_t func, void *info,
+ int wait)
+{
+ /*
+ * The address and the size of nmi_call_func_mask_data
+ * need to be aligned on L1_CACHE_BYTES.
+ */
+ static struct nmi_call_data_struct nmi_call_func_mask_data
+ __cacheline_aligned;
+ unsigned long start, end;
+
+ start = (unsigned long)&nmi_call_func_mask_data;
+ end = start + sizeof(struct nmi_call_data_struct);
+
+ nmi_call_func_mask_data.func = func;
+ nmi_call_func_mask_data.info = info;
+ nmi_call_func_mask_data.started = cpumask;
+ nmi_call_func_mask_data.wait = wait;
+ if (wait)
+ nmi_call_func_mask_data.finished = cpumask;
+
+ spin_lock(&smp_nmi_call_lock);
+ nmi_call_data = &nmi_call_func_mask_data;
+ mn10300_local_dcache_flush_range(start, end);
+ smp_wmb();
+
+ send_IPI_mask(cpumask, CALL_FUNCTION_NMI_IPI);
+
+ do {
+ mn10300_local_dcache_inv_range(start, end);
+ barrier();
+ } while (!cpus_empty(nmi_call_func_mask_data.started));
+
+ if (wait) {
+ do {
+ mn10300_local_dcache_inv_range(start, end);
+ barrier();
+ } while (!cpus_empty(nmi_call_func_mask_data.finished));
+ }
+
+ spin_unlock(&smp_nmi_call_lock);
+ return 0;
+}
+
+static void restart_wakeup_cpu(void)
+{
+ unsigned int cpu = smp_processor_id();
+
+ cpu_set(cpu, cpu_callin_map);
+ local_flush_tlb();
+ cpu_set(cpu, cpu_online_map);
+ smp_wmb();
+}
+
+static void prepare_sleep_cpu(void *unused)
+{
+ sleep_mode[smp_processor_id()] = 1;
+ smp_mb();
+ mn10300_local_dcache_flush_inv();
+ hotplug_cpu_disable_cache();
+ hotplug_cpu_invalidate_cache();
+}
+
+/* when this function called, IE=0, NMID=0. */
+static void sleep_cpu(void *unused)
+{
+ unsigned int cpu_id = smp_processor_id();
+ /*
+ * CALL_FUNCTION_NMI_IPI for wakeup_cpu() shall not be requested,
+ * before this cpu goes in SLEEP mode.
+ */
+ do {
+ smp_mb();
+ __sleep_cpu();
+ } while (sleep_mode[cpu_id]);
+ restart_wakeup_cpu();
+}
+
+static void run_sleep_cpu(unsigned int cpu)
+{
+ unsigned long flags;
+ cpumask_t cpumask = cpumask_of(cpu);
+
+ flags = arch_local_cli_save();
+ hotplug_cpu_nmi_call_function(cpumask, prepare_sleep_cpu, NULL, 1);
+ hotplug_cpu_nmi_call_function(cpumask, sleep_cpu, NULL, 0);
+ udelay(1); /* delay for the cpu to sleep. */
+ arch_local_irq_restore(flags);
+}
+
+static void wakeup_cpu(void)
+{
+ hotplug_cpu_invalidate_cache();
+ hotplug_cpu_enable_cache();
+ smp_mb();
+ sleep_mode[smp_processor_id()] = 0;
+}
+
+static void run_wakeup_cpu(unsigned int cpu)
+{
+ unsigned long flags;
+
+ flags = arch_local_cli_save();
+#if NR_CPUS == 2
+ mn10300_local_dcache_flush_inv();
+#else
+ /*
+ * Before waking up the cpu,
+ * all online cpus should stop and flush D-Cache for global data.
+ */
+#error not support NR_CPUS > 2, when CONFIG_HOTPLUG_CPU=y.
+#endif
+ hotplug_cpu_nmi_call_function(cpumask_of(cpu), wakeup_cpu, NULL, 1);
+ arch_local_irq_restore(flags);
+}
+
+#endif /* CONFIG_HOTPLUG_CPU */
diff --git a/arch/mn10300/kernel/switch_to.S b/arch/mn10300/kernel/switch_to.S
index 630aad7..b08cb2e 100644
--- a/arch/mn10300/kernel/switch_to.S
+++ b/arch/mn10300/kernel/switch_to.S
@@ -15,6 +15,9 @@
#include <linux/linkage.h>
#include <asm/thread_info.h>
#include <asm/cpu-regs.h>
+#ifdef CONFIG_SMP
+#include <proc/smp-regs.h>
+#endif /* CONFIG_SMP */
.text
@@ -35,7 +38,14 @@
mov d1,a1
# save prev context
+#ifdef CONFIG_SMP
+ mov (CPUID),a2
+ add a2,a2
+ add a2,a2
+ mov (___frame,a2),d0
+#else /* CONFIG_SMP */
mov (__frame),d0
+#endif /* CONFIG_SMP */
mov d0,(THREAD_FRAME,a0)
mov __switch_back,d0
mov d0,(THREAD_PC,a0)
@@ -59,7 +69,14 @@
#endif
mov (THREAD_FRAME,a1),a2
+#ifdef CONFIG_SMP
+ mov (CPUID),a0
+ add a0,a0
+ add a0,a0
+ mov a2,(___frame,a0)
+#else /* CONFIG_SMP */
mov a2,(__frame)
+#endif /* CONFIG_SMP */
mov (THREAD_PC,a1),a2
mov d2,d0 # for ret_from_fork
mov d0,a0 # for __switch_to
diff --git a/arch/mn10300/kernel/time.c b/arch/mn10300/kernel/time.c
index 0b5c856..0cb9bdb 100644
--- a/arch/mn10300/kernel/time.c
+++ b/arch/mn10300/kernel/time.c
@@ -22,12 +22,7 @@
#include <asm/processor.h>
#include <asm/intctl-regs.h>
#include <asm/rtc.h>
-
-#ifdef CONFIG_MN10300_RTC
-unsigned long mn10300_ioclk; /* system I/O clock frequency */
-unsigned long mn10300_iobclk; /* system I/O clock frequency */
-unsigned long mn10300_tsc_per_HZ; /* number of ioclks per jiffy */
-#endif /* CONFIG_MN10300_RTC */
+#include "internal.h"
static unsigned long mn10300_last_tsc; /* time-stamp counter at last time
* interrupt occurred */
@@ -95,6 +90,19 @@
__muldiv64u(NSEC_PER_SEC, 1 << 16, MN10300_TSCCLK);
}
+/**
+ * local_timer_interrupt - Local timer interrupt handler
+ *
+ * Handle local timer interrupts for this CPU. They may have been propagated
+ * to this CPU from the CPU that actually gets them by way of an IPI.
+ */
+irqreturn_t local_timer_interrupt(void)
+{
+ profile_tick(CPU_PROFILING);
+ update_process_times(user_mode(get_irq_regs()));
+ return IRQ_HANDLED;
+}
+
/*
* advance the kernel's time keeping clocks (xtime and jiffies)
* - we use Timer 0 & 1 cascaded as a clock to nudge us the next time
@@ -103,6 +111,7 @@
static irqreturn_t timer_interrupt(int irq, void *dev_id)
{
unsigned tsc, elapse;
+ irqreturn_t ret;
write_seqlock(&xtime_lock);
@@ -114,15 +123,16 @@
mn10300_last_tsc -= MN10300_TSC_PER_HZ;
/* advance the kernel's time tracking system */
- profile_tick(CPU_PROFILING);
do_timer(1);
}
write_sequnlock(&xtime_lock);
- update_process_times(user_mode(get_irq_regs()));
-
- return IRQ_HANDLED;
+ ret = local_timer_interrupt();
+#ifdef CONFIG_SMP
+ send_IPI_allbutself(LOCAL_TIMER_IPI);
+#endif
+ return ret;
}
/*
@@ -148,7 +158,7 @@
/* use timer 0 & 1 cascaded to tick at as close to HZ as possible */
setup_irq(TMJCIRQ, &timer_irq);
- set_intr_level(TMJCIRQ, TMJCICR_LEVEL);
+ set_intr_level(TMJCIRQ, NUM2GxICR_LEVEL(CONFIG_TIMER_IRQ_LEVEL));
startup_jiffies_counter();
diff --git a/arch/mn10300/kernel/traps.c b/arch/mn10300/kernel/traps.c
index 716a221..c924a1d 100644
--- a/arch/mn10300/kernel/traps.c
+++ b/arch/mn10300/kernel/traps.c
@@ -45,8 +45,13 @@
#error "INTERRUPT_VECTOR_BASE not aligned to 16MiB boundary!"
#endif
+#ifdef CONFIG_SMP
+struct pt_regs *___frame[NR_CPUS]; /* current frame pointer */
+EXPORT_SYMBOL(___frame);
+#else /* CONFIG_SMP */
struct pt_regs *__frame; /* current frame pointer */
EXPORT_SYMBOL(__frame);
+#endif /* CONFIG_SMP */
int kstack_depth_to_print = 24;
@@ -221,11 +226,14 @@
printk(KERN_EMERG "threadinfo=%p task=%p)\n",
current_thread_info(), current);
- if ((unsigned long) current >= 0x90000000UL &&
- (unsigned long) current < 0x94000000UL)
+ if ((unsigned long) current >= PAGE_OFFSET &&
+ (unsigned long) current < (unsigned long)high_memory)
printk(KERN_EMERG "Process %s (pid: %d)\n",
current->comm, current->pid);
+#ifdef CONFIG_SMP
+ printk(KERN_EMERG "CPUID: %08x\n", CPUID);
+#endif
printk(KERN_EMERG "CPUP: %04hx\n", CPUP);
printk(KERN_EMERG "TBR: %08x\n", TBR);
printk(KERN_EMERG "DEAR: %08x\n", DEAR);
@@ -521,8 +529,12 @@
{
unsigned long addr;
u8 *vector = (u8 *)(CONFIG_INTERRUPT_VECTOR_BASE + code);
+ unsigned long flags;
addr = (unsigned long) handler - (unsigned long) vector;
+
+ flags = arch_local_cli_save();
+
vector[0] = 0xdc; /* JMP handler */
vector[1] = addr;
vector[2] = addr >> 8;
@@ -532,6 +544,8 @@
vector[6] = 0xcb;
vector[7] = 0xcb;
+ arch_local_irq_restore(flags);
+
#ifndef CONFIG_MN10300_CACHE_SNOOP
mn10300_dcache_flush_inv();
mn10300_icache_inv();
diff --git a/arch/mn10300/lib/delay.c b/arch/mn10300/lib/delay.c
index fdf6f71..8e7ceb8 100644
--- a/arch/mn10300/lib/delay.c
+++ b/arch/mn10300/lib/delay.c
@@ -38,14 +38,14 @@
*/
void __udelay(unsigned long usecs)
{
- signed long ioclk, stop;
+ unsigned long start, stop, cnt;
/* usecs * CLK / 1E6 */
stop = __muldiv64u(usecs, MN10300_TSCCLK, 1000000);
- stop = TMTSCBC - stop;
+ start = TMTSCBC;
do {
- ioclk = TMTSCBC;
- } while (stop < ioclk);
+ cnt = start - TMTSCBC;
+ } while (cnt < stop);
}
EXPORT_SYMBOL(__udelay);
diff --git a/arch/mn10300/mm/fault.c b/arch/mn10300/mm/fault.c
index 906e4c8..59c3da4 100644
--- a/arch/mn10300/mm/fault.c
+++ b/arch/mn10300/mm/fault.c
@@ -39,10 +39,6 @@
{
if (yes) {
oops_in_progress = 1;
-#ifdef CONFIG_SMP
- /* Many serial drivers do __global_cli() */
- global_irq_lock = 0;
-#endif
} else {
int loglevel_save = console_loglevel;
#ifdef CONFIG_VT
@@ -334,10 +330,10 @@
*/
out_of_memory:
up_read(&mm->mmap_sem);
- if ((fault_code & MMUFCR_xFC_ACCESS) != MMUFCR_xFC_ACCESS_USR)
- goto no_context;
- pagefault_out_of_memory();
- return;
+ printk(KERN_ALERT "VM: killing process %s\n", tsk->comm);
+ if ((fault_code & MMUFCR_xFC_ACCESS) == MMUFCR_xFC_ACCESS_USR)
+ do_exit(SIGKILL);
+ goto no_context;
do_sigbus:
up_read(&mm->mmap_sem);
diff --git a/arch/mn10300/proc-mn103e010/include/proc/clock.h b/arch/mn10300/proc-mn103e010/include/proc/clock.h
index aa23e14..704a819 100644
--- a/arch/mn10300/proc-mn103e010/include/proc/clock.h
+++ b/arch/mn10300/proc-mn103e010/include/proc/clock.h
@@ -13,6 +13,4 @@
#include <unit/clock.h>
-#define MN10300_WDCLK MN10300_IOCLK
-
#endif /* _ASM_PROC_CLOCK_H */
diff --git a/arch/mn10300/proc-mn103e010/include/proc/intctl-regs.h b/arch/mn10300/proc-mn103e010/include/proc/intctl-regs.h
new file mode 100644
index 0000000..f537801
--- /dev/null
+++ b/arch/mn10300/proc-mn103e010/include/proc/intctl-regs.h
@@ -0,0 +1,29 @@
+#ifndef _ASM_PROC_INTCTL_REGS_H
+#define _ASM_PROC_INTCTL_REGS_H
+
+#ifndef _ASM_INTCTL_REGS_H
+# error "please don't include this file directly"
+#endif
+
+/* intr acceptance group reg */
+#define IAGR __SYSREG(0xd4000100, u16)
+
+/* group number register */
+#define IAGR_GN 0x00fc
+
+#define __GET_XIRQ_TRIGGER(X, Z) (((Z) >> ((X) * 2)) & 3)
+
+#define __SET_XIRQ_TRIGGER(X, Y, Z) \
+({ \
+ typeof(Z) x = (Z); \
+ x &= ~(3 << ((X) * 2)); \
+ x |= ((Y) & 3) << ((X) * 2); \
+ (Z) = x; \
+})
+
+/* external pin intr spec reg */
+#define EXTMD __SYSREG(0xd4000200, u16)
+#define GET_XIRQ_TRIGGER(X) __GET_XIRQ_TRIGGER(X, EXTMD)
+#define SET_XIRQ_TRIGGER(X, Y) __SET_XIRQ_TRIGGER(X, Y, EXTMD)
+
+#endif /* _ASM_PROC_INTCTL_REGS_H */
diff --git a/arch/mn10300/proc-mn103e010/proc-init.c b/arch/mn10300/proc-mn103e010/proc-init.c
index 0cee787..27b9798 100644
--- a/arch/mn10300/proc-mn103e010/proc-init.c
+++ b/arch/mn10300/proc-mn103e010/proc-init.c
@@ -11,6 +11,7 @@
#include <linux/kernel.h>
#include <asm/fpu.h>
#include <asm/rtc.h>
+#include <asm/busctl-regs.h>
/*
* initialise the on-silicon processor peripherals
@@ -75,3 +76,37 @@
calibrate_clock();
}
+
+/*
+ * determine the memory size and base from the memory controller regs
+ */
+void __init get_mem_info(unsigned long *mem_base, unsigned long *mem_size)
+{
+ unsigned long base, size;
+
+ *mem_base = 0;
+ *mem_size = 0;
+
+ base = SDBASE(0);
+ if (base & SDBASE_CE) {
+ size = (base & SDBASE_CBAM) << SDBASE_CBAM_SHIFT;
+ size = ~size + 1;
+ base &= SDBASE_CBA;
+
+ printk(KERN_INFO "SDRAM[0]: %luMb @%08lx\n", size >> 20, base);
+ *mem_size += size;
+ *mem_base = base;
+ }
+
+ base = SDBASE(1);
+ if (base & SDBASE_CE) {
+ size = (base & SDBASE_CBAM) << SDBASE_CBAM_SHIFT;
+ size = ~size + 1;
+ base &= SDBASE_CBA;
+
+ printk(KERN_INFO "SDRAM[1]: %luMb @%08lx\n", size >> 20, base);
+ *mem_size += size;
+ if (*mem_base == 0)
+ *mem_base = base;
+ }
+}
diff --git a/arch/mn10300/proc-mn2ws0050/Makefile b/arch/mn10300/proc-mn2ws0050/Makefile
new file mode 100644
index 0000000..d4ca133
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-y := proc-init.o
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/cache.h b/arch/mn10300/proc-mn2ws0050/include/proc/cache.h
new file mode 100644
index 0000000..cafd7b5
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/cache.h
@@ -0,0 +1,48 @@
+/* Cache specification
+ *
+ * Copyright (C) 2005 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 13-Nov-2006 MEI Add L1_CACHE_SHIFT_MAX definition.
+ * 29-Jul-2008 MEI Add define for MN10300_HAS_AREAPURGE_REG.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#ifndef _ASM_PROC_CACHE_H
+#define _ASM_PROC_CACHE_H
+
+/*
+ * L1 cache
+ */
+#define L1_CACHE_NWAYS 4 /* number of ways in caches */
+#define L1_CACHE_NENTRIES 128 /* number of entries in each way */
+#define L1_CACHE_BYTES 32 /* bytes per entry */
+#define L1_CACHE_SHIFT 5 /* shift for bytes per entry */
+#define L1_CACHE_WAYDISP 0x1000 /* distance from one way to the next */
+
+#define L1_CACHE_TAG_VALID 0x00000001 /* cache tag valid bit */
+#define L1_CACHE_TAG_DIRTY 0x00000008 /* data cache tag dirty bit */
+#define L1_CACHE_TAG_ENTRY 0x00000fe0 /* cache tag entry address mask */
+#define L1_CACHE_TAG_ADDRESS 0xfffff000 /* cache tag line address mask */
+
+/*
+ * specification of the interval between interrupt checking intervals whilst
+ * managing the cache with the interrupts disabled
+ */
+#define MN10300_DCACHE_INV_RANGE_INTR_LOG2_INTERVAL 4
+
+/*
+ * The size of range at which it becomes more economical to just flush the
+ * whole cache rather than trying to flush the specified range.
+ */
+#define MN10300_DCACHE_FLUSH_BORDER \
+ +(L1_CACHE_NWAYS * L1_CACHE_NENTRIES * L1_CACHE_BYTES)
+#define MN10300_DCACHE_FLUSH_INV_BORDER \
+ +(L1_CACHE_NWAYS * L1_CACHE_NENTRIES * L1_CACHE_BYTES)
+
+#endif /* _ASM_PROC_CACHE_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/clock.h b/arch/mn10300/proc-mn2ws0050/include/proc/clock.h
new file mode 100644
index 0000000..fe4c0a4
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/clock.h
@@ -0,0 +1,20 @@
+/* clock.h: proc-specific clocks
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 23-Feb-2007 MEI Delete define for watchdog timer.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#ifndef _ASM_PROC_CLOCK_H
+#define _ASM_PROC_CLOCK_H
+
+#include <unit/clock.h>
+
+#endif /* _ASM_PROC_CLOCK_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/dmactl-regs.h b/arch/mn10300/proc-mn2ws0050/include/proc/dmactl-regs.h
new file mode 100644
index 0000000..4c4319e
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/dmactl-regs.h
@@ -0,0 +1,103 @@
+/* MN2WS0050 on-board DMA controller registers
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+
+#ifndef _ASM_PROC_DMACTL_REGS_H
+#define _ASM_PROC_DMACTL_REGS_H
+
+#include <asm/cpu-regs.h>
+
+#ifdef __KERNEL__
+
+/* DMA registers */
+#define DMxCTR(N) __SYSREG(0xd4005000+(N*0x100), u32) /* control reg */
+#define DMxCTR_BG 0x0000001f /* transfer request source */
+#define DMxCTR_BG_SOFT 0x00000000 /* - software source */
+#define DMxCTR_BG_SC0TX 0x00000002 /* - serial port 0 transmission */
+#define DMxCTR_BG_SC0RX 0x00000003 /* - serial port 0 reception */
+#define DMxCTR_BG_SC1TX 0x00000004 /* - serial port 1 transmission */
+#define DMxCTR_BG_SC1RX 0x00000005 /* - serial port 1 reception */
+#define DMxCTR_BG_SC2TX 0x00000006 /* - serial port 2 transmission */
+#define DMxCTR_BG_SC2RX 0x00000007 /* - serial port 2 reception */
+#define DMxCTR_BG_TM0UFLOW 0x00000008 /* - timer 0 underflow */
+#define DMxCTR_BG_TM1UFLOW 0x00000009 /* - timer 1 underflow */
+#define DMxCTR_BG_TM2UFLOW 0x0000000a /* - timer 2 underflow */
+#define DMxCTR_BG_TM3UFLOW 0x0000000b /* - timer 3 underflow */
+#define DMxCTR_BG_TM6ACMPCAP 0x0000000c /* - timer 6A compare/capture */
+#define DMxCTR_BG_RYBY 0x0000000d /* - NAND Flash RY/BY request source */
+#define DMxCTR_BG_RMC 0x0000000e /* - remote controller output */
+#define DMxCTR_BG_XIRQ12 0x00000011 /* - XIRQ12 pin interrupt source */
+#define DMxCTR_BG_XIRQ13 0x00000012 /* - XIRQ13 pin interrupt source */
+#define DMxCTR_BG_TCK 0x00000014 /* - tick timer underflow */
+#define DMxCTR_BG_SC4TX 0x00000019 /* - serial port4 transmission */
+#define DMxCTR_BG_SC4RX 0x0000001a /* - serial port4 reception */
+#define DMxCTR_BG_SC5TX 0x0000001b /* - serial port5 transmission */
+#define DMxCTR_BG_SC5RX 0x0000001c /* - serial port5 reception */
+#define DMxCTR_BG_SC6TX 0x0000001d /* - serial port6 transmission */
+#define DMxCTR_BG_SC6RX 0x0000001e /* - serial port6 reception */
+#define DMxCTR_BG_TMSUFLOW 0x0000001f /* - timestamp timer underflow */
+#define DMxCTR_SAM 0x00000060 /* DMA transfer src addr mode */
+#define DMxCTR_SAM_INCR 0x00000000 /* - increment */
+#define DMxCTR_SAM_DECR 0x00000020 /* - decrement */
+#define DMxCTR_SAM_FIXED 0x00000040 /* - fixed */
+#define DMxCTR_DAM 0x00000300 /* DMA transfer dest addr mode */
+#define DMxCTR_DAM_INCR 0x00000000 /* - increment */
+#define DMxCTR_DAM_DECR 0x00000100 /* - decrement */
+#define DMxCTR_DAM_FIXED 0x00000200 /* - fixed */
+#define DMxCTR_UT 0x00006000 /* DMA transfer unit */
+#define DMxCTR_UT_1 0x00000000 /* - 1 byte */
+#define DMxCTR_UT_2 0x00002000 /* - 2 byte */
+#define DMxCTR_UT_4 0x00004000 /* - 4 byte */
+#define DMxCTR_UT_16 0x00006000 /* - 16 byte */
+#define DMxCTR_RRE 0x00008000 /* DMA round robin enable */
+#define DMxCTR_TEN 0x00010000 /* DMA channel transfer enable */
+#define DMxCTR_RQM 0x00060000 /* external request input source mode */
+#define DMxCTR_RQM_FALLEDGE 0x00000000 /* - falling edge */
+#define DMxCTR_RQM_RISEEDGE 0x00020000 /* - rising edge */
+#define DMxCTR_RQM_LOLEVEL 0x00040000 /* - low level */
+#define DMxCTR_RQM_HILEVEL 0x00060000 /* - high level */
+#define DMxCTR_RQF 0x01000000 /* DMA transfer request flag */
+#define DMxCTR_PERR 0x40000000 /* DMA transfer parameter error flag */
+#define DMxCTR_XEND 0x80000000 /* DMA transfer end flag */
+
+#define DMxSRC(N) __SYSREG(0xd4005004+(N*0x100), u32) /* control reg */
+
+#define DMxDST(N) __SYSREG(0xd4005008+(N*0x100), u32) /* source addr reg */
+
+#define DMxSIZ(N) __SYSREG(0xd400500c+(N*0x100), u32) /* dest addr reg */
+#define DMxSIZ_CT 0x000fffff /* number of bytes to transfer */
+
+#define DMxCYC(N) __SYSREG(0xd4005010+(N*0x100), u32) /* intermittent size reg */
+#define DMxCYC_CYC 0x000000ff /* number of interrmittent transfers -1 */
+
+#define DM0IRQ 16 /* DMA channel 0 complete IRQ */
+#define DM1IRQ 17 /* DMA channel 1 complete IRQ */
+#define DM2IRQ 18 /* DMA channel 2 complete IRQ */
+#define DM3IRQ 19 /* DMA channel 3 complete IRQ */
+
+#define DM0ICR GxICR(DM0IRQ) /* DMA channel 0 complete intr ctrl reg */
+#define DM1ICR GxICR(DM0IR1) /* DMA channel 1 complete intr ctrl reg */
+#define DM2ICR GxICR(DM0IR2) /* DMA channel 2 complete intr ctrl reg */
+#define DM3ICR GxICR(DM0IR3) /* DMA channel 3 complete intr ctrl reg */
+
+#ifndef __ASSEMBLY__
+
+struct mn10300_dmactl_regs {
+ u32 ctr;
+ const void *src;
+ void *dst;
+ u32 siz;
+ u32 cyc;
+} __attribute__((aligned(0x100)));
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_PROC_DMACTL_REGS_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/intctl-regs.h b/arch/mn10300/proc-mn2ws0050/include/proc/intctl-regs.h
new file mode 100644
index 0000000..a1e9772
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/intctl-regs.h
@@ -0,0 +1,29 @@
+#ifndef _ASM_PROC_INTCTL_REGS_H
+#define _ASM_PROC_INTCTL_REGS_H
+
+#ifndef _ASM_INTCTL_REGS_H
+# error "please don't include this file directly"
+#endif
+
+/* intr acceptance group reg */
+#define IAGR __SYSREG(0xd4000100, u16)
+
+/* group number register */
+#define IAGR_GN 0x003fc
+
+#define __GET_XIRQ_TRIGGER(X, Z) (((Z) >> ((X) * 2)) & 3)
+
+#define __SET_XIRQ_TRIGGER(X, Y, Z) \
+({ \
+ typeof(Z) x = (Z); \
+ x &= ~(3 << ((X) * 2)); \
+ x |= ((Y) & 3) << ((X) * 2); \
+ (Z) = x; \
+})
+
+/* external pin intr spec reg */
+#define EXTMD0 __SYSREG(0xd4000200, u32)
+#define GET_XIRQ_TRIGGER(X) __GET_XIRQ_TRIGGER(X, EXTMD0)
+#define SET_XIRQ_TRIGGER(X, Y) __SET_XIRQ_TRIGGER(X, Y, EXTMD0)
+
+#endif /* _ASM_PROC_INTCTL_REGS_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/irq.h b/arch/mn10300/proc-mn2ws0050/include/proc/irq.h
new file mode 100644
index 0000000..37777a8
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/irq.h
@@ -0,0 +1,49 @@
+/* MN2WS0050 on-board interrupt controller registers
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 13-Nov-2006 MEI Define extended IRQ number for SMP support.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _PROC_IRQ_H
+#define _PROC_IRQ_H
+
+#ifdef __KERNEL__
+
+#define GxICR_NUM_IRQS 163
+#ifdef CONFIG_SMP
+#define GxICR_NUM_EXT_IRQS 197
+#endif /* CONFIG_SMP */
+
+#define GxICR_NUM_XIRQS 16
+
+#define XIRQ0 34
+#define XIRQ1 35
+#define XIRQ2 36
+#define XIRQ3 37
+#define XIRQ4 38
+#define XIRQ5 39
+#define XIRQ6 40
+#define XIRQ7 41
+#define XIRQ8 42
+#define XIRQ9 43
+#define XIRQ10 44
+#define XIRQ11 45
+#define XIRQ12 46
+#define XIRQ13 47
+#define XIRQ14 48
+#define XIRQ15 49
+
+#define XIRQ2IRQ(num) (XIRQ0 + num)
+
+#endif /* __KERNEL__ */
+
+#endif /* _PROC_IRQ_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/nand-regs.h b/arch/mn10300/proc-mn2ws0050/include/proc/nand-regs.h
new file mode 100644
index 0000000..84448f3
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/nand-regs.h
@@ -0,0 +1,120 @@
+/* NAND flash interface register definitions
+ *
+ * Copyright (C) 2008-2009 Panasonic Corporation
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _PROC_NAND_REGS_H_
+#define _PROC_NAND_REGS_H_
+
+/* command register */
+#define FCOMMAND_0 __SYSREG(0xd8f00000, u8) /* fcommand[24:31] */
+#define FCOMMAND_1 __SYSREG(0xd8f00001, u8) /* fcommand[16:23] */
+#define FCOMMAND_2 __SYSREG(0xd8f00002, u8) /* fcommand[8:15] */
+#define FCOMMAND_3 __SYSREG(0xd8f00003, u8) /* fcommand[0:7] */
+
+/* for dma 16 byte trans, use FCOMMAND2 register */
+#define FCOMMAND2_0 __SYSREG(0xd8f00110, u8) /* fcommand2[24:31] */
+#define FCOMMAND2_1 __SYSREG(0xd8f00111, u8) /* fcommand2[16:23] */
+#define FCOMMAND2_2 __SYSREG(0xd8f00112, u8) /* fcommand2[8:15] */
+#define FCOMMAND2_3 __SYSREG(0xd8f00113, u8) /* fcommand2[0:7] */
+
+#define FCOMMAND_FIEN 0x80 /* nand flash I/F enable */
+#define FCOMMAND_BW_8BIT 0x00 /* 8bit bus width */
+#define FCOMMAND_BW_16BIT 0x40 /* 16bit bus width */
+#define FCOMMAND_BLOCKSZ_SMALL 0x00 /* small block */
+#define FCOMMAND_BLOCKSZ_LARGE 0x20 /* large block */
+#define FCOMMAND_DMASTART 0x10 /* dma start */
+#define FCOMMAND_RYBY 0x08 /* ready/busy flag */
+#define FCOMMAND_RYBYINTMSK 0x04 /* mask ready/busy interrupt */
+#define FCOMMAND_XFWP 0x02 /* write protect enable */
+#define FCOMMAND_XFCE 0x01 /* flash device disable */
+#define FCOMMAND_SEQKILL 0x10 /* stop seq-read */
+#define FCOMMAND_ANUM 0x07 /* address cycle */
+#define FCOMMAND_ANUM_NONE 0x00 /* address cycle none */
+#define FCOMMAND_ANUM_1CYC 0x01 /* address cycle 1cycle */
+#define FCOMMAND_ANUM_2CYC 0x02 /* address cycle 2cycle */
+#define FCOMMAND_ANUM_3CYC 0x03 /* address cycle 3cycle */
+#define FCOMMAND_ANUM_4CYC 0x04 /* address cycle 4cycle */
+#define FCOMMAND_ANUM_5CYC 0x05 /* address cycle 5cycle */
+#define FCOMMAND_FCMD_READ0 0x00 /* read1 command */
+#define FCOMMAND_FCMD_SEQIN 0x80 /* page program 1st command */
+#define FCOMMAND_FCMD_PAGEPROG 0x10 /* page program 2nd command */
+#define FCOMMAND_FCMD_RESET 0xff /* reset command */
+#define FCOMMAND_FCMD_ERASE1 0x60 /* erase 1st command */
+#define FCOMMAND_FCMD_ERASE2 0xd0 /* erase 2nd command */
+#define FCOMMAND_FCMD_STATUS 0x70 /* read status command */
+#define FCOMMAND_FCMD_READID 0x90 /* read id command */
+#define FCOMMAND_FCMD_READOOB 0x50 /* read3 command */
+/* address register */
+#define FADD __SYSREG(0xd8f00004, u32)
+/* address register 2 */
+#define FADD2 __SYSREG(0xd8f00008, u32)
+/* error judgement register */
+#define FJUDGE __SYSREG(0xd8f0000c, u32)
+#define FJUDGE_NOERR 0x0 /* no error */
+#define FJUDGE_1BITERR 0x1 /* 1bit error in data area */
+#define FJUDGE_PARITYERR 0x2 /* parity error */
+#define FJUDGE_UNCORRECTABLE 0x3 /* uncorrectable error */
+#define FJUDGE_ERRJDG_MSK 0x3 /* mask of judgement result */
+/* 1st ECC store register */
+#define FECC11 __SYSREG(0xd8f00010, u32)
+/* 2nd ECC store register */
+#define FECC12 __SYSREG(0xd8f00014, u32)
+/* 3rd ECC store register */
+#define FECC21 __SYSREG(0xd8f00018, u32)
+/* 4th ECC store register */
+#define FECC22 __SYSREG(0xd8f0001c, u32)
+/* 5th ECC store register */
+#define FECC31 __SYSREG(0xd8f00020, u32)
+/* 6th ECC store register */
+#define FECC32 __SYSREG(0xd8f00024, u32)
+/* 7th ECC store register */
+#define FECC41 __SYSREG(0xd8f00028, u32)
+/* 8th ECC store register */
+#define FECC42 __SYSREG(0xd8f0002c, u32)
+/* data register */
+#define FDATA __SYSREG(0xd8f00030, u32)
+/* access pulse register */
+#define FPWS __SYSREG(0xd8f00100, u32)
+#define FPWS_PWS1W_2CLK 0x00000000 /* write pulse width 1clock */
+#define FPWS_PWS1W_3CLK 0x01000000 /* write pulse width 2clock */
+#define FPWS_PWS1W_4CLK 0x02000000 /* write pulse width 4clock */
+#define FPWS_PWS1W_5CLK 0x03000000 /* write pulse width 5clock */
+#define FPWS_PWS1W_6CLK 0x04000000 /* write pulse width 6clock */
+#define FPWS_PWS1W_7CLK 0x05000000 /* write pulse width 7clock */
+#define FPWS_PWS1W_8CLK 0x06000000 /* write pulse width 8clock */
+#define FPWS_PWS1R_3CLK 0x00010000 /* read pulse width 3clock */
+#define FPWS_PWS1R_4CLK 0x00020000 /* read pulse width 4clock */
+#define FPWS_PWS1R_5CLK 0x00030000 /* read pulse width 5clock */
+#define FPWS_PWS1R_6CLK 0x00040000 /* read pulse width 6clock */
+#define FPWS_PWS1R_7CLK 0x00050000 /* read pulse width 7clock */
+#define FPWS_PWS1R_8CLK 0x00060000 /* read pulse width 8clock */
+#define FPWS_PWS2W_2CLK 0x00000100 /* write pulse interval 2clock */
+#define FPWS_PWS2W_3CLK 0x00000200 /* write pulse interval 3clock */
+#define FPWS_PWS2W_4CLK 0x00000300 /* write pulse interval 4clock */
+#define FPWS_PWS2W_5CLK 0x00000400 /* write pulse interval 5clock */
+#define FPWS_PWS2W_6CLK 0x00000500 /* write pulse interval 6clock */
+#define FPWS_PWS2R_2CLK 0x00000001 /* read pulse interval 2clock */
+#define FPWS_PWS2R_3CLK 0x00000002 /* read pulse interval 3clock */
+#define FPWS_PWS2R_4CLK 0x00000003 /* read pulse interval 4clock */
+#define FPWS_PWS2R_5CLK 0x00000004 /* read pulse interval 5clock */
+#define FPWS_PWS2R_6CLK 0x00000005 /* read pulse interval 6clock */
+/* command register 2 */
+#define FCOMMAND2 __SYSREG(0xd8f00110, u32)
+/* transfer frequency register */
+#define FNUM __SYSREG(0xd8f00114, u32)
+#define FSDATA_ADDR 0xd8f00400
+/* active data register */
+#define FSDATA __SYSREG(FSDATA_ADDR, u32)
+
+#endif /* _PROC_NAND_REGS_H_ */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/proc.h b/arch/mn10300/proc-mn2ws0050/include/proc/proc.h
new file mode 100644
index 0000000..90d5cad
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/proc.h
@@ -0,0 +1,18 @@
+/* proc.h: MN2WS0050 processor description
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _ASM_PROC_PROC_H
+#define _ASM_PROC_PROC_H
+
+#define PROCESSOR_VENDOR_NAME "Panasonic"
+#define PROCESSOR_MODEL_NAME "mn2ws0050"
+
+#endif /* _ASM_PROC_PROC_H */
diff --git a/arch/mn10300/proc-mn2ws0050/include/proc/smp-regs.h b/arch/mn10300/proc-mn2ws0050/include/proc/smp-regs.h
new file mode 100644
index 0000000..22f277f
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/include/proc/smp-regs.h
@@ -0,0 +1,51 @@
+/* MN10300/AM33v2 Microcontroller SMP registers
+ *
+ * Copyright (C) 2006 Matsushita Electric Industrial Co., Ltd.
+ * All Rights Reserved.
+ * Created:
+ * 13-Nov-2006 MEI Add extended cache and atomic operation register
+ * for SMP support.
+ * 23-Feb-2007 MEI Add define for gdbstub SMP.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _ASM_PROC_SMP_REGS_H
+#define _ASM_PROC_SMP_REGS_H
+
+#ifdef __KERNEL__
+
+#ifndef __ASSEMBLY__
+#include <linux/types.h>
+#endif
+#include <asm/cpu-regs.h>
+
+/*
+ * Reference to the interrupt controllers of other CPUs
+ */
+#define CROSS_ICR_CPU_SHIFT 16
+
+#define CROSS_GxICR(X, CPU) __SYSREG(0xc4000000 + (X) * 4 + \
+ ((X) >= 64 && (X) < 192) * 0xf00 + ((CPU) << CROSS_ICR_CPU_SHIFT), u16)
+#define CROSS_GxICR_u8(X, CPU) __SYSREG(0xc4000000 + (X) * 4 + \
+ (((X) >= 64) && ((X) < 192)) * 0xf00 + ((CPU) << CROSS_ICR_CPU_SHIFT), u8)
+
+/* CPU ID register */
+#define CPUID __SYSREGC(0xc0000054, u32)
+#define CPUID_MASK 0x00000007 /* CPU ID mask */
+
+/* extended cache control register */
+#define ECHCTR __SYSREG(0xc0000c20, u32)
+#define ECHCTR_IBCM 0x00000001 /* instruction cache broad cast mask */
+#define ECHCTR_DBCM 0x00000002 /* data cache broad cast mask */
+#define ECHCTR_ISPM 0x00000004 /* instruction cache snoop mask */
+#define ECHCTR_DSPM 0x00000008 /* data cache snoop mask */
+
+#define NMIAGR __SYSREG(0xd400013c, u16)
+#define NMIAGR_GN 0x03fc
+
+#endif /* __KERNEL__ */
+#endif /* _ASM_PROC_SMP_REGS_H */
diff --git a/arch/mn10300/proc-mn2ws0050/proc-init.c b/arch/mn10300/proc-mn2ws0050/proc-init.c
new file mode 100644
index 0000000..c58249b
--- /dev/null
+++ b/arch/mn10300/proc-mn2ws0050/proc-init.c
@@ -0,0 +1,134 @@
+/* MN2WS0050 processor initialisation
+ *
+ * Copyright (C) 2005 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/uaccess.h>
+#include <asm/io.h>
+#include <asm/atomic.h>
+#include <asm/smp.h>
+#include <asm/pgalloc.h>
+#include <asm/busctl-regs.h>
+#include <unit/timex.h>
+#include <asm/fpu.h>
+#include <asm/rtc.h>
+
+#define MEMCONF __SYSREGC(0xdf800400, u32)
+
+/*
+ * initialise the on-silicon processor peripherals
+ */
+asmlinkage void __init processor_init(void)
+{
+ int loop;
+
+ /* set up the exception table first */
+ for (loop = 0x000; loop < 0x400; loop += 8)
+ __set_intr_stub(loop, __common_exception);
+
+ __set_intr_stub(EXCEP_ITLBMISS, itlb_miss);
+ __set_intr_stub(EXCEP_DTLBMISS, dtlb_miss);
+ __set_intr_stub(EXCEP_IAERROR, itlb_aerror);
+ __set_intr_stub(EXCEP_DAERROR, dtlb_aerror);
+ __set_intr_stub(EXCEP_BUSERROR, raw_bus_error);
+ __set_intr_stub(EXCEP_DOUBLE_FAULT, double_fault);
+ __set_intr_stub(EXCEP_FPU_DISABLED, fpu_disabled);
+ __set_intr_stub(EXCEP_SYSCALL0, system_call);
+
+ __set_intr_stub(EXCEP_NMI, nmi_handler);
+ __set_intr_stub(EXCEP_WDT, nmi_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL0, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL1, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL2, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL3, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL4, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL5, irq_handler);
+ __set_intr_stub(EXCEP_IRQ_LEVEL6, irq_handler);
+
+ IVAR0 = EXCEP_IRQ_LEVEL0;
+ IVAR1 = EXCEP_IRQ_LEVEL1;
+ IVAR2 = EXCEP_IRQ_LEVEL2;
+ IVAR3 = EXCEP_IRQ_LEVEL3;
+ IVAR4 = EXCEP_IRQ_LEVEL4;
+ IVAR5 = EXCEP_IRQ_LEVEL5;
+ IVAR6 = EXCEP_IRQ_LEVEL6;
+
+#ifndef CONFIG_MN10300_HAS_CACHE_SNOOP
+ mn10300_dcache_flush_inv();
+ mn10300_icache_inv();
+#endif
+
+ /* disable all interrupts and set to priority 6 (lowest) */
+#ifdef CONFIG_SMP
+ for (loop = 0; loop < GxICR_NUM_IRQS; loop++)
+ GxICR(loop) = GxICR_LEVEL_6 | GxICR_DETECT;
+#else /* !CONFIG_SMP */
+ for (loop = 0; loop < NR_IRQS; loop++)
+ GxICR(loop) = GxICR_LEVEL_6 | GxICR_DETECT;
+#endif /* !CONFIG_SMP */
+
+ /* clear the timers */
+ TM0MD = 0;
+ TM1MD = 0;
+ TM2MD = 0;
+ TM3MD = 0;
+ TM4MD = 0;
+ TM5MD = 0;
+ TM6MD = 0;
+ TM6MDA = 0;
+ TM6MDB = 0;
+ TM7MD = 0;
+ TM8MD = 0;
+ TM9MD = 0;
+ TM10MD = 0;
+ TM11MD = 0;
+ TM12MD = 0;
+ TM13MD = 0;
+ TM14MD = 0;
+ TM15MD = 0;
+
+ calibrate_clock();
+}
+
+/*
+ * determine the memory size and base from the memory controller regs
+ */
+void __init get_mem_info(unsigned long *mem_base, unsigned long *mem_size)
+{
+ unsigned long memconf = MEMCONF;
+ unsigned long size = 0; /* order: MByte */
+
+ *mem_base = 0x90000000; /* fixed address */
+
+ switch (memconf & 0x00000003) {
+ case 0x01:
+ size = 256 / 8; /* 256 Mbit per chip */
+ break;
+ case 0x02:
+ size = 512 / 8; /* 512 Mbit per chip */
+ break;
+ case 0x03:
+ size = 1024 / 8; /* 1 Gbit per chip */
+ break;
+ default:
+ panic("Invalid SDRAM size");
+ break;
+ }
+
+ printk(KERN_INFO "DDR2-SDRAM: %luMB x 2 @%08lx\n", size, *mem_base);
+
+ *mem_size = (size * 2) << 20;
+}
diff --git a/arch/mn10300/unit-asb2303/include/unit/clock.h b/arch/mn10300/unit-asb2303/include/unit/clock.h
index 2a0bf79..0316907 100644
--- a/arch/mn10300/unit-asb2303/include/unit/clock.h
+++ b/arch/mn10300/unit-asb2303/include/unit/clock.h
@@ -14,32 +14,11 @@
#ifndef __ASSEMBLY__
-#ifdef CONFIG_MN10300_RTC
-
-extern unsigned long mn10300_ioclk; /* IOCLK (crystal speed) in HZ */
-extern unsigned long mn10300_iobclk;
-extern unsigned long mn10300_tsc_per_HZ;
-
-#define MN10300_IOCLK mn10300_ioclk
-/* If this processors has a another clock, uncomment the below. */
-/* #define MN10300_IOBCLK mn10300_iobclk */
-
-#else /* !CONFIG_MN10300_RTC */
-
#define MN10300_IOCLK 33333333UL
/* #define MN10300_IOBCLK 66666666UL */
-#endif /* !CONFIG_MN10300_RTC */
-
-#define MN10300_JCCLK MN10300_IOCLK
-#define MN10300_TSCCLK MN10300_IOCLK
-
-#ifdef CONFIG_MN10300_RTC
-#define MN10300_TSC_PER_HZ mn10300_tsc_per_HZ
-#else /* !CONFIG_MN10300_RTC */
-#define MN10300_TSC_PER_HZ (MN10300_TSCCLK/HZ)
-#endif /* !CONFIG_MN10300_RTC */
-
#endif /* !__ASSEMBLY__ */
+#define MN10300_WDCLK MN10300_IOCLK
+
#endif /* _ASM_UNIT_CLOCK_H */
diff --git a/arch/mn10300/unit-asb2303/include/unit/serial.h b/arch/mn10300/unit-asb2303/include/unit/serial.h
index 047566c..991e356 100644
--- a/arch/mn10300/unit-asb2303/include/unit/serial.h
+++ b/arch/mn10300/unit-asb2303/include/unit/serial.h
@@ -22,6 +22,11 @@
#define SERIAL_IRQ XIRQ0 /* Dual serial (PC16552) (Hi) */
/*
+ * The ASB2303 has an 18.432 MHz clock the UART
+ */
+#define BASE_BAUD (18432000 / 16)
+
+/*
* dispose of the /dev/ttyS0 and /dev/ttyS1 serial ports
*/
#ifndef CONFIG_GDBSTUB_ON_TTYSx
diff --git a/arch/mn10300/unit-asb2303/include/unit/timex.h b/arch/mn10300/unit-asb2303/include/unit/timex.h
index 88cd96b..d1b8daf 100644
--- a/arch/mn10300/unit-asb2303/include/unit/timex.h
+++ b/arch/mn10300/unit-asb2303/include/unit/timex.h
@@ -1,4 +1,4 @@
-/* ASB2303-specific timer specifcations
+/* ASB2303-specific timer specifications
*
* Copyright (C) 2007 Red Hat, Inc. All Rights Reserved.
* Written by David Howells (dhowells@redhat.com)
@@ -17,6 +17,7 @@
#include <asm/timer-regs.h>
#include <unit/clock.h>
+#include <asm/param.h>
/*
* jiffies counter specifications
@@ -29,32 +30,43 @@
#define TMJCBR TM01BR
#define TMJCIRQ TM1IRQ
#define TMJCICR TM1ICR
-#define TMJCICR_LEVEL GxICR_LEVEL_5
#ifndef __ASSEMBLY__
+#define MN10300_SRC_IOCLK MN10300_IOCLK
+
+#ifndef HZ
+# error HZ undeclared.
+#endif /* !HZ */
+/* use as little prescaling as possible to avoid losing accuracy */
+#if (MN10300_SRC_IOCLK + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 1
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK
+#elif (MN10300_SRC_IOCLK / 8 + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 8
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK_8
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK_8
+#elif (MN10300_SRC_IOCLK / 32 + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 32
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK_32
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK_32
+#else
+# error You lose.
+#endif
+
+#define MN10300_JCCLK (MN10300_SRC_IOCLK / IOCLK_PRESCALE)
+#define MN10300_TSCCLK (MN10300_SRC_IOCLK / IOCLK_PRESCALE)
+
+#define MN10300_JC_PER_HZ ((MN10300_JCCLK + HZ / 2) / HZ)
+#define MN10300_TSC_PER_HZ ((MN10300_TSCCLK + HZ / 2) / HZ)
+
static inline void startup_jiffies_counter(void)
{
- unsigned rate;
u16 md, t16;
- /* use as little prescaling as possible to avoid losing accuracy */
- md = TM0MD_SRC_IOCLK;
- rate = MN10300_JCCLK / HZ;
-
- if (rate > TMJCBR_MAX) {
- md = TM0MD_SRC_IOCLK_8;
- rate = MN10300_JCCLK / 8 / HZ;
-
- if (rate > TMJCBR_MAX) {
- md = TM0MD_SRC_IOCLK_32;
- rate = MN10300_JCCLK / 32 / HZ;
-
- BUG_ON(rate > TMJCBR_MAX);
- }
- }
-
- TMJCBR = rate - 1;
+ md = JC_TIMER_CLKSRC;
+ TMJCBR = MN10300_JC_PER_HZ - 1;
t16 = TMJCBR;
TMJCMD =
@@ -93,29 +105,39 @@
static inline void startup_timestamp_counter(void)
{
+ u32 t32;
+
/* set up timer 4 & 5 cascaded as a 32-bit counter to count real time
* - count down from 4Gig-1 to 0 and wrap at IOCLK rate
*/
TM45BR = TMTSCBR_MAX;
+ t32 = TM45BR;
- TM4MD = TM4MD_SRC_IOCLK;
+ TM4MD = TSC_TIMER_CLKSRC;
TM4MD |= TM4MD_INIT_COUNTER;
TM4MD &= ~TM4MD_INIT_COUNTER;
TM4ICR = 0;
+ t32 = TM4ICR;
TM5MD = TM5MD_SRC_TM4CASCADE;
TM5MD |= TM5MD_INIT_COUNTER;
TM5MD &= ~TM5MD_INIT_COUNTER;
TM5ICR = 0;
+ t32 = TM5ICR;
TM5MD |= TM5MD_COUNT_ENABLE;
TM4MD |= TM4MD_COUNT_ENABLE;
+ t32 = TM5MD;
+ t32 = TM4MD;
}
static inline void shutdown_timestamp_counter(void)
{
+ u8 t8;
TM4MD = 0;
TM5MD = 0;
+ t8 = TM4MD;
+ t8 = TM5MD;
}
/*
diff --git a/arch/mn10300/unit-asb2303/unit-init.c b/arch/mn10300/unit-asb2303/unit-init.c
index 70e8cb4..834a76a 100644
--- a/arch/mn10300/unit-asb2303/unit-init.c
+++ b/arch/mn10300/unit-asb2303/unit-init.c
@@ -31,6 +31,14 @@
SET_XIRQ_TRIGGER(3, XIRQ_TRIGGER_HILEVEL);
SET_XIRQ_TRIGGER(4, XIRQ_TRIGGER_LOWLEVEL);
SET_XIRQ_TRIGGER(5, XIRQ_TRIGGER_LOWLEVEL);
+
+#ifdef CONFIG_EXT_SERIAL_IRQ_LEVEL
+ set_intr_level(XIRQ0, NUM2GxICR_LEVEL(CONFIG_EXT_SERIAL_IRQ_LEVEL));
+#endif
+
+#ifdef CONFIG_ETHERNET_IRQ_LEVEL
+ set_intr_level(XIRQ3, NUM2GxICR_LEVEL(CONFIG_ETHERNET_IRQ_LEVEL));
+#endif
}
/*
@@ -51,7 +59,7 @@
switch (GET_XIRQ_TRIGGER(extnum)) {
case XIRQ_TRIGGER_HILEVEL:
case XIRQ_TRIGGER_LOWLEVEL:
- set_intr_postackable(XIRQ2IRQ(extnum));
+ mn10300_set_lateack_irq_type(XIRQ2IRQ(extnum));
break;
default:
break;
diff --git a/arch/mn10300/unit-asb2305/include/unit/clock.h b/arch/mn10300/unit-asb2305/include/unit/clock.h
index 67be3f2..29e3425 100644
--- a/arch/mn10300/unit-asb2305/include/unit/clock.h
+++ b/arch/mn10300/unit-asb2305/include/unit/clock.h
@@ -14,32 +14,11 @@
#ifndef __ASSEMBLY__
-#ifdef CONFIG_MN10300_RTC
-
-extern unsigned long mn10300_ioclk; /* IOCLK (crystal speed) in HZ */
-extern unsigned long mn10300_iobclk;
-extern unsigned long mn10300_tsc_per_HZ;
-
-#define MN10300_IOCLK mn10300_ioclk
-/* If this processors has a another clock, uncomment the below. */
-/* #define MN10300_IOBCLK mn10300_iobclk */
-
-#else /* !CONFIG_MN10300_RTC */
-
#define MN10300_IOCLK 33333333UL
/* #define MN10300_IOBCLK 66666666UL */
-#endif /* !CONFIG_MN10300_RTC */
-
-#define MN10300_JCCLK MN10300_IOCLK
-#define MN10300_TSCCLK MN10300_IOCLK
-
-#ifdef CONFIG_MN10300_RTC
-#define MN10300_TSC_PER_HZ mn10300_tsc_per_HZ
-#else /* !CONFIG_MN10300_RTC */
-#define MN10300_TSC_PER_HZ (MN10300_TSCCLK/HZ)
-#endif /* !CONFIG_MN10300_RTC */
-
#endif /* !__ASSEMBLY__ */
+#define MN10300_WDCLK MN10300_IOCLK
+
#endif /* _ASM_UNIT_CLOCK_H */
diff --git a/arch/mn10300/unit-asb2305/include/unit/serial.h b/arch/mn10300/unit-asb2305/include/unit/serial.h
index 8086cc0..88c0821 100644
--- a/arch/mn10300/unit-asb2305/include/unit/serial.h
+++ b/arch/mn10300/unit-asb2305/include/unit/serial.h
@@ -21,6 +21,11 @@
#define SERIAL_IRQ XIRQ0 /* Dual serial (PC16552) (Hi) */
/*
+ * The ASB2305 has an 18.432 MHz clock the UART
+ */
+#define BASE_BAUD (18432000 / 16)
+
+/*
* dispose of the /dev/ttyS0 serial port
*/
#ifndef CONFIG_GDBSTUB_ON_TTYSx
diff --git a/arch/mn10300/unit-asb2305/include/unit/timex.h b/arch/mn10300/unit-asb2305/include/unit/timex.h
index 0860186..cd8bc14 100644
--- a/arch/mn10300/unit-asb2305/include/unit/timex.h
+++ b/arch/mn10300/unit-asb2305/include/unit/timex.h
@@ -1,4 +1,4 @@
-/* ASB2305 timer specifcations
+/* ASB2305-specific timer specifications
*
* Copyright (C) 2007 Red Hat, Inc. All Rights Reserved.
* Written by David Howells (dhowells@redhat.com)
@@ -17,6 +17,7 @@
#include <asm/timer-regs.h>
#include <unit/clock.h>
+#include <asm/param.h>
/*
* jiffies counter specifications
@@ -29,32 +30,43 @@
#define TMJCBR TM01BR
#define TMJCIRQ TM1IRQ
#define TMJCICR TM1ICR
-#define TMJCICR_LEVEL GxICR_LEVEL_5
#ifndef __ASSEMBLY__
+#define MN10300_SRC_IOCLK MN10300_IOCLK
+
+#ifndef HZ
+# error HZ undeclared.
+#endif /* !HZ */
+/* use as little prescaling as possible to avoid losing accuracy */
+#if (MN10300_SRC_IOCLK + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 1
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK
+#elif (MN10300_SRC_IOCLK / 8 + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 8
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK_8
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK_8
+#elif (MN10300_SRC_IOCLK / 32 + HZ / 2) / HZ - 1 <= TMJCBR_MAX
+# define IOCLK_PRESCALE 32
+# define JC_TIMER_CLKSRC TM0MD_SRC_IOCLK_32
+# define TSC_TIMER_CLKSRC TM4MD_SRC_IOCLK_32
+#else
+# error You lose.
+#endif
+
+#define MN10300_JCCLK (MN10300_SRC_IOCLK / IOCLK_PRESCALE)
+#define MN10300_TSCCLK (MN10300_SRC_IOCLK / IOCLK_PRESCALE)
+
+#define MN10300_JC_PER_HZ ((MN10300_JCCLK + HZ / 2) / HZ)
+#define MN10300_TSC_PER_HZ ((MN10300_TSCCLK + HZ / 2) / HZ)
+
static inline void startup_jiffies_counter(void)
{
- unsigned rate;
u16 md, t16;
- /* use as little prescaling as possible to avoid losing accuracy */
- md = TM0MD_SRC_IOCLK;
- rate = MN10300_JCCLK / HZ;
-
- if (rate > TMJCBR_MAX) {
- md = TM0MD_SRC_IOCLK_8;
- rate = MN10300_JCCLK / 8 / HZ;
-
- if (rate > TMJCBR_MAX) {
- md = TM0MD_SRC_IOCLK_32;
- rate = MN10300_JCCLK / 32 / HZ;
-
- BUG_ON(rate > TMJCBR_MAX);
- }
- }
-
- TMJCBR = rate - 1;
+ md = JC_TIMER_CLKSRC;
+ TMJCBR = MN10300_JC_PER_HZ - 1;
t16 = TMJCBR;
TMJCMD =
@@ -93,29 +105,39 @@
static inline void startup_timestamp_counter(void)
{
+ u32 t32;
+
/* set up timer 4 & 5 cascaded as a 32-bit counter to count real time
* - count down from 4Gig-1 to 0 and wrap at IOCLK rate
*/
TM45BR = TMTSCBR_MAX;
+ t32 = TM45BR;
- TM4MD = TM4MD_SRC_IOCLK;
+ TM4MD = TSC_TIMER_CLKSRC;
TM4MD |= TM4MD_INIT_COUNTER;
TM4MD &= ~TM4MD_INIT_COUNTER;
TM4ICR = 0;
+ t32 = TM4ICR;
TM5MD = TM5MD_SRC_TM4CASCADE;
TM5MD |= TM5MD_INIT_COUNTER;
TM5MD &= ~TM5MD_INIT_COUNTER;
TM5ICR = 0;
+ t32 = TM5ICR;
TM5MD |= TM5MD_COUNT_ENABLE;
TM4MD |= TM4MD_COUNT_ENABLE;
+ t32 = TM5MD;
+ t32 = TM4MD;
}
static inline void shutdown_timestamp_counter(void)
{
+ u8 t8;
TM4MD = 0;
TM5MD = 0;
+ t8 = TM4MD;
+ t8 = TM5MD;
}
/*
@@ -126,7 +148,7 @@
static inline cycles_t read_timestamp_counter(void)
{
- return (cycles_t) TMTSCBC;
+ return (cycles_t)TMTSCBC;
}
#endif /* !__ASSEMBLY__ */
diff --git a/arch/mn10300/unit-asb2305/pci.c b/arch/mn10300/unit-asb2305/pci.c
index 6d8720a..a4954fe 100644
--- a/arch/mn10300/unit-asb2305/pci.c
+++ b/arch/mn10300/unit-asb2305/pci.c
@@ -503,7 +503,7 @@
struct pci_ops *o = &pci_direct_ampci;
u32 x;
- set_intr_level(XIRQ1, GxICR_LEVEL_3);
+ set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_PCI_IRQ_LEVEL));
memset(&bus, 0, sizeof(bus));
diff --git a/arch/mn10300/unit-asb2305/unit-init.c b/arch/mn10300/unit-asb2305/unit-init.c
index a76c8e0..e1becd6 100644
--- a/arch/mn10300/unit-asb2305/unit-init.c
+++ b/arch/mn10300/unit-asb2305/unit-init.c
@@ -26,8 +26,10 @@
{
#ifndef CONFIG_GDBSTUB_ON_TTYSx
/* set the 16550 interrupt line to level 3 if not being used for GDB */
- set_intr_level(XIRQ0, GxICR_LEVEL_3);
+#ifdef CONFIG_EXT_SERIAL_IRQ_LEVEL
+ set_intr_level(XIRQ0, NUM2GxICR_LEVEL(CONFIG_EXT_SERIAL_IRQ_LEVEL));
#endif
+#endif /* CONFIG_GDBSTUB_ON_TTYSx */
}
/*
@@ -51,7 +53,7 @@
switch (GET_XIRQ_TRIGGER(extnum)) {
case XIRQ_TRIGGER_HILEVEL:
case XIRQ_TRIGGER_LOWLEVEL:
- set_intr_postackable(XIRQ2IRQ(extnum));
+ mn10300_set_lateack_irq_type(XIRQ2IRQ(extnum));
break;
default:
break;
diff --git a/arch/mn10300/unit-asb2364/Makefile b/arch/mn10300/unit-asb2364/Makefile
new file mode 100644
index 0000000..6dd27d6
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/Makefile
@@ -0,0 +1,10 @@
+#
+# Makefile for the linux kernel.
+#
+# Note! Dependencies are done automagically by 'make dep', which also
+# removes any old dependencies. DON'T put your own dependencies here
+# unless it's something special (ie not a .c file).
+#
+# Note 2! The CFLAGS definitions are now in the main makefile...
+
+obj-y := unit-init.o leds.o
diff --git a/arch/mn10300/unit-asb2364/include/unit/clock.h b/arch/mn10300/unit-asb2364/include/unit/clock.h
new file mode 100644
index 0000000..d34ac9a
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/include/unit/clock.h
@@ -0,0 +1,29 @@
+/* clock.h: unit-specific clocks
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * Modified by Matsushita Electric Industrial Co., Ltd.
+ * Modifications:
+ * 23-Feb-2007 MEI Add define for watchdog timer.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _ASM_UNIT_CLOCK_H
+#define _ASM_UNIT_CLOCK_H
+
+#ifndef __ASSEMBLY__
+
+#define MN10300_IOCLK 100000000UL /* for DDR800 */
+/*#define MN10300_IOCLK 83333333UL */ /* for DDR667 */
+#define MN10300_IOBCLK MN10300_IOCLK /* IOBCLK is equal to IOCLK */
+
+#endif /* !__ASSEMBLY__ */
+
+#define MN10300_WDCLK 27000000UL
+
+#endif /* _ASM_UNIT_CLOCK_H */
diff --git a/arch/mn10300/unit-asb2364/include/unit/fpga-regs.h b/arch/mn10300/unit-asb2364/include/unit/fpga-regs.h
new file mode 100644
index 0000000..a039a50c
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/include/unit/fpga-regs.h
@@ -0,0 +1,50 @@
+/* ASB2364 FPGA registers
+ */
+
+#ifndef _ASM_UNIT_FPGA_REGS_H
+#define _ASM_UNIT_FPGA_REGS_H
+
+#include <asm/cpu-regs.h>
+
+#ifdef __KERNEL__
+
+#define ASB2364_FPGA_REG_RESET_LAN __SYSREG(0xa9001300, u16)
+#define ASB2364_FPGA_REG_RESET_UART __SYSREG(0xa9001304, u16)
+#define ASB2364_FPGA_REG_RESET_I2C __SYSREG(0xa9001308, u16)
+#define ASB2364_FPGA_REG_RESET_USB __SYSREG(0xa900130c, u16)
+#define ASB2364_FPGA_REG_RESET_AV __SYSREG(0xa9001310, u16)
+
+#define ASB2364_FPGA_REG_IRQ_LAN __SYSREG(0xa9001510, u16)
+#define ASB2364_FPGA_REG_IRQ_UART __SYSREG(0xa9001514, u16)
+#define ASB2364_FPGA_REG_IRQ_I2C __SYSREG(0xa9001518, u16)
+#define ASB2364_FPGA_REG_IRQ_USB __SYSREG(0xa900151c, u16)
+#define ASB2364_FPGA_REG_IRQ_FPGA __SYSREG(0xa9001524, u16)
+
+#define ASB2364_FPGA_REG_MASK_LAN __SYSREG(0xa9001590, u16)
+#define ASB2364_FPGA_REG_MASK_UART __SYSREG(0xa9001594, u16)
+#define ASB2364_FPGA_REG_MASK_I2C __SYSREG(0xa9001598, u16)
+#define ASB2364_FPGA_REG_MASK_USB __SYSREG(0xa900159c, u16)
+#define ASB2364_FPGA_REG_MASK_FPGA __SYSREG(0xa90015a4, u16)
+
+#define ASB2364_FPGA_REG_CPLD5_SET1 __SYSREG(0xa9002500, u16)
+#define ASB2364_FPGA_REG_CPLD5_SET2 __SYSREG(0xa9002504, u16)
+#define ASB2364_FPGA_REG_CPLD6_SET1 __SYSREG(0xa9002600, u16)
+#define ASB2364_FPGA_REG_CPLD6_SET2 __SYSREG(0xa9002604, u16)
+#define ASB2364_FPGA_REG_CPLD7_SET1 __SYSREG(0xa9002700, u16)
+#define ASB2364_FPGA_REG_CPLD7_SET2 __SYSREG(0xa9002704, u16)
+#define ASB2364_FPGA_REG_CPLD8_SET1 __SYSREG(0xa9002800, u16)
+#define ASB2364_FPGA_REG_CPLD8_SET2 __SYSREG(0xa9002804, u16)
+#define ASB2364_FPGA_REG_CPLD9_SET1 __SYSREG(0xa9002900, u16)
+#define ASB2364_FPGA_REG_CPLD9_SET2 __SYSREG(0xa9002904, u16)
+#define ASB2364_FPGA_REG_CPLD10_SET1 __SYSREG(0xa9002a00, u16)
+#define ASB2364_FPGA_REG_CPLD10_SET2 __SYSREG(0xa9002a04, u16)
+
+#define SyncExBus() \
+ do { \
+ unsigned short w; \
+ w = *(volatile short *)0xa9000000; \
+ } while (0)
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_UNIT_FPGA_REGS_H */
diff --git a/arch/mn10300/unit-asb2364/include/unit/leds.h b/arch/mn10300/unit-asb2364/include/unit/leds.h
new file mode 100644
index 0000000..03a3933
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/include/unit/leds.h
@@ -0,0 +1,54 @@
+/* Unit-specific leds
+ *
+ * Copyright (C) 2005 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _ASM_UNIT_LEDS_H
+#define _ASM_UNIT_LEDS_H
+
+#include <asm/pio-regs.h>
+#include <asm/cpu-regs.h>
+#include <asm/exceptions.h>
+
+#define MN10300_USE_7SEGLEDS 0
+
+#define ASB2364_7SEGLEDS __SYSREG(0xA9001630, u32)
+
+/*
+ * use the 7-segment LEDs to indicate states
+ */
+
+#if MN10300_USE_7SEGLEDS
+/* flip the 7-segment LEDs between "Gdb-" and "----" */
+#define mn10300_set_gdbleds(ONOFF) \
+ do { \
+ ASB2364_7SEGLEDS = (ONOFF) ? 0x8543077f : 0x7f7f7f7f; \
+ } while (0)
+#else
+#define mn10300_set_gdbleds(ONOFF) do {} while (0)
+#endif
+
+#if MN10300_USE_7SEGLEDS
+/* indicate double-fault by displaying "db-f" on the LEDs */
+#define mn10300_set_dbfleds \
+ mov 0x43077f1d,d0 ; \
+ mov d0,(ASB2364_7SEGLEDS)
+#else
+#define mn10300_set_dbfleds
+#endif
+
+#ifndef __ASSEMBLY__
+extern void peripheral_leds_display_exception(enum exception_code);
+extern void peripheral_leds_led_chase(void);
+extern void peripheral_leds7x4_display_dec(unsigned int, unsigned int);
+extern void peripheral_leds7x4_display_hex(unsigned int, unsigned int);
+extern void debug_to_serial(const char *, int);
+#endif /* __ASSEMBLY__ */
+
+#endif /* _ASM_UNIT_LEDS_H */
diff --git a/arch/mn10300/unit-asb2364/include/unit/serial.h b/arch/mn10300/unit-asb2364/include/unit/serial.h
new file mode 100644
index 0000000..7f048bb
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/include/unit/serial.h
@@ -0,0 +1,151 @@
+/* Unit-specific 8250 serial ports
+ *
+ * Copyright (C) 2005 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _ASM_UNIT_SERIAL_H
+#define _ASM_UNIT_SERIAL_H
+
+#include <asm/cpu-regs.h>
+#include <proc/irq.h>
+#include <unit/fpga-regs.h>
+#include <linux/serial_reg.h>
+
+#define SERIAL_PORT0_BASE_ADDRESS 0xA8200000
+
+#define SERIAL_IRQ XIRQ1 /* single serial (TL16C550C) (Lo) */
+
+/*
+ * The ASB2364 has an 12.288 MHz clock
+ * for your UART.
+ *
+ * It'd be nice if someone built a serial card with a 24.576 MHz
+ * clock, since the 16550A is capable of handling a top speed of 1.5
+ * megabits/second; but this requires the faster clock.
+ */
+#define BASE_BAUD (12288000 / 16)
+
+/*
+ * dispose of the /dev/ttyS0 and /dev/ttyS1 serial ports
+ */
+#ifndef CONFIG_GDBSTUB_ON_TTYSx
+
+#define SERIAL_PORT_DFNS \
+ { \
+ .baud_base = BASE_BAUD, \
+ .irq = SERIAL_IRQ, \
+ .flags = STD_COM_FLAGS, \
+ .iomem_base = (u8 *) SERIAL_PORT0_BASE_ADDRESS, \
+ .iomem_reg_shift = 1, \
+ .io_type = SERIAL_IO_MEM, \
+ },
+
+#ifndef __ASSEMBLY__
+
+static inline void __debug_to_serial(const char *p, int n)
+{
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#else /* CONFIG_GDBSTUB_ON_TTYSx */
+
+#define SERIAL_PORT_DFNS /* stolen by gdb-stub */
+
+#if defined(CONFIG_GDBSTUB_ON_TTYS0)
+#define GDBPORT_SERIAL_RX __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_RX * 4, u8)
+#define GDBPORT_SERIAL_TX __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_TX * 4, u8)
+#define GDBPORT_SERIAL_DLL __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_DLL * 4, u8)
+#define GDBPORT_SERIAL_DLM __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_DLM * 4, u8)
+#define GDBPORT_SERIAL_IER __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IER * 4, u8)
+#define GDBPORT_SERIAL_IIR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IIR * 4, u8)
+#define GDBPORT_SERIAL_FCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_FCR * 4, u8)
+#define GDBPORT_SERIAL_LCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_LCR * 4, u8)
+#define GDBPORT_SERIAL_MCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_MCR * 4, u8)
+#define GDBPORT_SERIAL_LSR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_LSR * 4, u8)
+#define GDBPORT_SERIAL_MSR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_MSR * 4, u8)
+#define GDBPORT_SERIAL_SCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_SCR * 4, u8)
+#define GDBPORT_SERIAL_IRQ SERIAL_IRQ
+
+#elif defined(CONFIG_GDBSTUB_ON_TTYS1)
+#error The ASB2364 does not have a /dev/ttyS1
+#endif
+
+#ifndef __ASSEMBLY__
+
+static inline void __debug_to_serial(const char *p, int n)
+{
+ char ch;
+
+#define LSR_WAIT_FOR(STATE) \
+ do {} while (!(GDBPORT_SERIAL_LSR & UART_LSR_##STATE))
+#define FLOWCTL_QUERY(LINE) \
+ ({ GDBPORT_SERIAL_MSR & UART_MSR_##LINE; })
+#define FLOWCTL_WAIT_FOR(LINE) \
+ do {} while (!(GDBPORT_SERIAL_MSR & UART_MSR_##LINE))
+#define FLOWCTL_CLEAR(LINE) \
+ do { GDBPORT_SERIAL_MCR &= ~UART_MCR_##LINE; } while (0)
+#define FLOWCTL_SET(LINE) \
+ do { GDBPORT_SERIAL_MCR |= UART_MCR_##LINE; } while (0)
+
+ FLOWCTL_SET(DTR);
+
+ for (; n > 0; n--) {
+ LSR_WAIT_FOR(THRE);
+ FLOWCTL_WAIT_FOR(CTS);
+
+ ch = *p++;
+ if (ch == 0x0a) {
+ GDBPORT_SERIAL_TX = 0x0d;
+ LSR_WAIT_FOR(THRE);
+ FLOWCTL_WAIT_FOR(CTS);
+ }
+ GDBPORT_SERIAL_TX = ch;
+ }
+
+ FLOWCTL_CLEAR(DTR);
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* CONFIG_GDBSTUB_ON_TTYSx */
+
+#define SERIAL_INITIALIZE \
+do { \
+ /* release reset */ \
+ ASB2364_FPGA_REG_RESET_UART = 0x0001; \
+ SyncExBus(); \
+} while (0)
+
+#define SERIAL_CHECK_INTERRUPT \
+do { \
+ if ((ASB2364_FPGA_REG_IRQ_UART & 0x0001) == 0x0001) { \
+ return IRQ_NONE; \
+ } \
+} while (0)
+
+#define SERIAL_CLEAR_INTERRUPT \
+do { \
+ ASB2364_FPGA_REG_IRQ_UART = 0x0001; \
+ SyncExBus(); \
+} while (0)
+
+#define SERIAL_SET_INT_MASK \
+do { \
+ ASB2364_FPGA_REG_MASK_UART = 0x0001; \
+ SyncExBus(); \
+} while (0)
+
+#define SERIAL_CLEAR_INT_MASK \
+do { \
+ ASB2364_FPGA_REG_MASK_UART = 0x0000; \
+ SyncExBus(); \
+} while (0)
+
+#endif /* _ASM_UNIT_SERIAL_H */
diff --git a/arch/mn10300/unit-asb2364/include/unit/timex.h b/arch/mn10300/unit-asb2364/include/unit/timex.h
new file mode 100644
index 0000000..b5223f7
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/include/unit/timex.h
@@ -0,0 +1,125 @@
+/* timex.h: MN2WS0038 architecture timer specifications
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#ifndef _ASM_UNIT_TIMEX_H
+#define _ASM_UNIT_TIMEX_H
+
+#ifndef __ASSEMBLY__
+#include <linux/irq.h>
+#endif /* __ASSEMBLY__ */
+
+#include <asm/timer-regs.h>
+#include <unit/clock.h>
+#include <asm/param.h>
+
+/*
+ * jiffies counter specifications
+ */
+
+#define TMJCBR_MAX 0xffffff /* 24bit */
+#define TMJCBC TMTBC
+
+#define TMJCMD TMTMD
+#define TMJCBR TMTBR
+#define TMJCIRQ TMTIRQ
+#define TMJCICR TMTICR
+
+#ifndef __ASSEMBLY__
+
+#define MN10300_SRC_IOBCLK MN10300_IOBCLK
+
+#ifndef HZ
+# error HZ undeclared.
+#endif /* !HZ */
+
+#define MN10300_JCCLK (MN10300_SRC_IOBCLK)
+#define MN10300_TSCCLK (MN10300_SRC_IOBCLK)
+
+#define MN10300_JC_PER_HZ ((MN10300_JCCLK + HZ / 2) / HZ)
+#define MN10300_TSC_PER_HZ ((MN10300_TSCCLK + HZ / 2) / HZ)
+
+/* Check bit width of MTM interval value that sets base register */
+#if (MN10300_JC_PER_HZ - 1) > TMJCBR_MAX
+# error MTM tick timer interval value is overflow.
+#endif
+
+
+static inline void startup_jiffies_counter(void)
+{
+ u32 sync;
+
+ TMJCBR = MN10300_JC_PER_HZ - 1;
+ sync = TMJCBR;
+
+ TMJCMD = TMTMD_TMTLDE;
+ TMJCMD = TMTMD_TMTCNE;
+ sync = TMJCMD;
+
+ TMJCICR |= GxICR_ENABLE | GxICR_DETECT | GxICR_REQUEST;
+ sync = TMJCICR;
+}
+
+static inline void shutdown_jiffies_counter(void)
+{
+}
+
+#endif /* !__ASSEMBLY__ */
+
+
+/*
+ * timestamp counter specifications
+ */
+
+#define TMTSCBR_MAX 0xffffffff
+#define TMTSCMD TMSMD
+#define TMTSCBR TMSBR
+#define TMTSCBC TMSBC
+#define TMTSCICR TMSICR
+
+#ifndef __ASSEMBLY__
+
+static inline void startup_timestamp_counter(void)
+{
+ u32 sync;
+
+ /* set up TMS(Timestamp) 32bit timer register to count real time
+ * - count down from 4Gig-1 to 0 and wrap at IOBCLK rate
+ */
+
+ TMTSCBR = TMTSCBR_MAX;
+ sync = TMTSCBR;
+
+ TMTSCICR = 0;
+ sync = TMTSCICR;
+
+ TMTSCMD = TMTMD_TMTLDE;
+ TMTSCMD = TMTMD_TMTCNE;
+ sync = TMTSCMD;
+}
+
+static inline void shutdown_timestamp_counter(void)
+{
+ TMTSCMD = 0;
+}
+
+/*
+ * we use a cascaded pair of 16-bit down-counting timers to count I/O
+ * clock cycles for the purposes of time keeping
+ */
+typedef unsigned long cycles_t;
+
+static inline cycles_t read_timestamp_counter(void)
+{
+ return (cycles_t)TMTSCBC;
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_UNIT_TIMEX_H */
diff --git a/arch/mn10300/unit-asb2364/leds.c b/arch/mn10300/unit-asb2364/leds.c
new file mode 100644
index 0000000..1ff830c
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/leds.c
@@ -0,0 +1,98 @@
+/* leds.c: ASB2364 peripheral 7seg LEDs x4 support
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/param.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/intctl-regs.h>
+#include <asm/rtc-regs.h>
+#include <unit/leds.h>
+
+#if MN10300_USE_7SEGLEDS
+static const u8 asb2364_led_hex_tbl[16] = {
+ 0x80, 0xf2, 0x48, 0x60, 0x32, 0x24, 0x04, 0xf0,
+ 0x00, 0x20, 0x10, 0x06, 0x8c, 0x42, 0x0c, 0x1c
+};
+
+static const u32 asb2364_led_chase_tbl[6] = {
+ ~0x02020202, /* top - segA */
+ ~0x04040404, /* right top - segB */
+ ~0x08080808, /* right bottom - segC */
+ ~0x10101010, /* bottom - segD */
+ ~0x20202020, /* left bottom - segE */
+ ~0x40404040, /* left top - segF */
+};
+
+static unsigned asb2364_led_chase;
+
+void peripheral_leds7x4_display_dec(unsigned int val, unsigned int points)
+{
+ u32 leds;
+
+ leds = asb2364_led_hex_tbl[(val/1000) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[(val/100) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[(val/10) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[val % 10];
+ leds |= points^0x01010101;
+
+ ASB2364_7SEGLEDS = leds;
+}
+
+void peripheral_leds7x4_display_hex(unsigned int val, unsigned int points)
+{
+ u32 leds;
+
+ leds = asb2364_led_hex_tbl[(val/1000) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[(val/100) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[(val/10) % 10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[val % 10];
+ leds |= points^0x01010101;
+
+ ASB2364_7SEGLEDS = leds;
+}
+
+/* display triple horizontal bar and exception code */
+void peripheral_leds_display_exception(enum exception_code code)
+{
+ u32 leds;
+
+ leds = asb2364_led_hex_tbl[(code/0x100) % 0x10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[(code/0x10) % 0x10];
+ leds <<= 8;
+ leds |= asb2364_led_hex_tbl[code % 0x10];
+ leds |= 0x6d010101;
+
+ ASB2364_7SEGLEDS = leds;
+}
+
+void peripheral_leds_led_chase(void)
+{
+ ASB2364_7SEGLEDS = asb2364_led_chase_tbl[asb2364_led_chase];
+ asb2364_led_chase++;
+ if (asb2364_led_chase >= 6)
+ asb2364_led_chase = 0;
+}
+#else /* MN10300_USE_7SEGLEDS */
+void peripheral_leds7x4_display_dec(unsigned int val, unsigned int points) { }
+void peripheral_leds7x4_display_hex(unsigned int val, unsigned int points) { }
+void peripheral_leds_display_exception(enum exception_code code) { }
+void peripheral_leds_led_chase(void) { }
+#endif /* MN10300_USE_7SEGLEDS */
diff --git a/arch/mn10300/unit-asb2364/unit-init.c b/arch/mn10300/unit-asb2364/unit-init.c
new file mode 100644
index 0000000..a3fc09b
--- /dev/null
+++ b/arch/mn10300/unit-asb2364/unit-init.c
@@ -0,0 +1,85 @@
+/* ASB2364 initialisation
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/param.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/processor.h>
+#include <asm/irq.h>
+#include <asm/intctl-regs.h>
+
+/*
+ * initialise some of the unit hardware before gdbstub is set up
+ */
+asmlinkage void __init unit_init(void)
+{
+ /* set up the external interrupts */
+
+ /* XIRQ[0]: NAND RXBY */
+ /* SET_XIRQ_TRIGGER(0, XIRQ_TRIGGER_LOWLEVEL); */
+
+ /* XIRQ[1]: LAN, UART, I2C, USB, PCI, FPGA */
+ SET_XIRQ_TRIGGER(1, XIRQ_TRIGGER_LOWLEVEL);
+
+ /* XIRQ[2]: Extend Slot 1-9 */
+ /* SET_XIRQ_TRIGGER(2, XIRQ_TRIGGER_LOWLEVEL); */
+
+#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL) && \
+ defined(CONFIG_ETHERNET_IRQ_LEVEL) && \
+ (CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL)
+# error CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL
+#endif
+
+#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL)
+ set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_EXT_SERIAL_IRQ_LEVEL));
+#elif defined(CONFIG_ETHERNET_IRQ_LEVEL)
+ set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_ETHERNET_IRQ_LEVEL));
+#endif
+}
+
+/*
+ * initialise the rest of the unit hardware after gdbstub is ready
+ */
+asmlinkage void __init unit_setup(void)
+{
+
+}
+
+/*
+ * initialise the external interrupts used by a unit of this type
+ */
+void __init unit_init_IRQ(void)
+{
+ unsigned int extnum;
+
+ for (extnum = 0 ; extnum < NR_XIRQS ; extnum++) {
+ switch (GET_XIRQ_TRIGGER(extnum)) {
+ /* LEVEL triggered interrupts should be made
+ * post-ACK'able as they hold their lines until
+ * serviced
+ */
+ case XIRQ_TRIGGER_HILEVEL:
+ case XIRQ_TRIGGER_LOWLEVEL:
+ mn10300_set_lateack_irq_type(XIRQ2IRQ(extnum));
+ break;
+ default:
+ break;
+ }
+ }
+
+#define IRQCTL __SYSREG(0xd5000090, u32)
+ IRQCTL |= 0x02;
+}