[PATCH] New PowerPC 4xx on-chip ethernet controller driver
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 27732fd..54ab70e 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1163,38 +1163,74 @@
be called ibmveth.
config IBM_EMAC
- bool "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC && BROKEN
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
depends on IBM_EMAC
- default "8"
+ default "32"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
+ depends on IBM_EMAC
+ default "256"
+
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"