libata-sff: ata_sff_irq_clear() is BMDMA specific
ata_sff_irq_clear() is BMDMA specific. Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.
Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
possibly by sata_sil. This should be moved to respective low
level drivers later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 19ddf92..55bc488 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -63,7 +63,6 @@
.sff_tf_read = ata_sff_tf_read,
.sff_exec_command = ata_sff_exec_command,
.sff_data_xfer = ata_sff_data_xfer,
- .sff_irq_clear = ata_sff_irq_clear,
.sff_drain_fifo = ata_sff_drain_fifo,
.lost_interrupt = ata_sff_lost_interrupt,
@@ -395,33 +394,12 @@
ata_sff_set_devctl(ap, ap->ctl);
ata_wait_idle(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_irq_on);
/**
- * ata_sff_irq_clear - Clear PCI IDE BMDMA interrupt.
- * @ap: Port associated with this ATA transaction.
- *
- * Clear interrupt and error flags in DMA status register.
- *
- * May be used as the irq_clear() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_sff_irq_clear(struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- if (!mmio)
- return;
-
- iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
-}
-EXPORT_SYMBOL_GPL(ata_sff_irq_clear);
-
-/**
* ata_sff_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
* @tf: ATA taskfile register set
@@ -1572,7 +1550,8 @@
}
/* clear irq events */
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
ata_sff_hsm_move(ap, qc, status, 0);
@@ -1588,7 +1567,8 @@
#ifdef ATA_IRQ_TRAP
if ((ap->stats.idle_irq % 1000) == 0) {
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
ata_port_printk(ap, KERN_WARNING, "irq trap\n");
return 1;
}
@@ -1658,7 +1638,8 @@
if (idle & (1 << i)) {
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
} else {
/* clear INTRQ and check if BUSY cleared */
if (!(ap->ops->sff_check_status(ap) & ATA_BUSY))
@@ -1744,7 +1725,8 @@
*/
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_freeze);
@@ -1761,7 +1743,8 @@
{
/* clear & re-enable interrupts */
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
ata_sff_irq_on(ap);
}
EXPORT_SYMBOL_GPL(ata_sff_thaw);
@@ -2580,6 +2563,7 @@
.qc_prep = ata_bmdma_qc_prep,
.qc_issue = ata_bmdma_qc_issue,
+ .sff_irq_clear = ata_bmdma_irq_clear,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
@@ -2848,7 +2832,8 @@
/* if we're gonna thaw, make sure IRQ is clear */
if (thaw) {
ap->ops->sff_check_status(ap);
- ap->ops->sff_irq_clear(ap);
+ if (ap->ops->sff_irq_clear)
+ ap->ops->sff_irq_clear(ap);
}
}
@@ -2882,6 +2867,28 @@
EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd);
/**
+ * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Clear interrupt and error flags in DMA status register.
+ *
+ * May be used as the irq_clear() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_bmdma_irq_clear(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ if (!mmio)
+ return;
+
+ iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
+}
+EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);
+
+/**
* ata_bmdma_setup - Set up PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
*