Merge 3.10-rc5 into char-misc-next
diff --git a/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt b/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt
new file mode 100644
index 0000000..c1d22b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/atmel-at91_cf.txt
@@ -0,0 +1,19 @@
+Atmel AT91RM9200 CompactFlash
+
+Required properties:
+- compatible : "atmel,at91rm9200-cf".
+- reg : should specify localbus address and size used.
+- gpios : specifies the gpio pins to control the CF device. Detect
+ and reset gpio's are mandatory while irq and vcc gpio's are
+ optional and may be set to 0 if not present.
+
+Example:
+compact-flash@50000000 {
+ compatible = "atmel,at91rm9200-cf";
+ reg = <0x50000000 0x30000000>;
+ gpios = <&pioC 13 0 /* irq */
+ &pioC 15 0 /* detect */
+ 0 /* vcc */
+ &pioC 5 0 /* reset */
+ >;
+};
diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
new file mode 100644
index 0000000..653c90c
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
@@ -0,0 +1,156 @@
+Device tree bindings for MVEBU Device Bus controllers
+
+The Device Bus controller available in some Marvell's SoC allows to control
+different types of standard memory and I/O devices such as NOR, NAND, and FPGA.
+The actual devices are instantiated from the child nodes of a Device Bus node.
+
+Required properties:
+
+ - compatible: Currently only Armada 370/XP SoC are supported,
+ with this compatible string:
+
+ marvell,mvebu-devbus
+
+ - reg: A resource specifier for the register space.
+ This is the base address of a chip select within
+ the controller's register space.
+ (see the example below)
+
+ - #address-cells: Must be set to 1
+ - #size-cells: Must be set to 1
+ - ranges: Must be set up to reflect the memory layout with four
+ integer values for each chip-select line in use:
+ 0 <physical address of mapping> <size>
+
+Mandatory timing properties for child nodes:
+
+Read parameters:
+
+ - devbus,turn-off-ps: Defines the time during which the controller does not
+ drive the AD bus after the completion of a device read.
+ This prevents contentions on the Device Bus after a read
+ cycle from a slow device.
+
+ - devbus,bus-width: Defines the bus width (e.g. <16>)
+
+ - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle,
+ to read data sample. This parameter is useful for
+ synchronous pipelined devices, where the address
+ precedes the read data by one or two cycles.
+
+ - devbus,acc-first-ps: Defines the time delay from the negation of
+ ALE[0] to the cycle that the first read data is sampled
+ by the controller.
+
+ - devbus,acc-next-ps: Defines the time delay between the cycle that
+ samples data N and the cycle that samples data N+1
+ (in burst accesses).
+
+ - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to
+ DEV_OEn assertion. If set to 0 (default),
+ DEV_OEn and DEV_CSn are asserted at the same cycle.
+ This parameter has no affect on <acc-first-ps> parameter
+ (no affect on first data sample). Set <rd-setup-ps>
+ to a value smaller than <acc-first-ps>.
+
+ - devbus,rd-hold-ps: Defines the time between the last data sample to the
+ de-assertion of DEV_CSn. If set to 0 (default),
+ DEV_OEn and DEV_CSn are de-asserted at the same cycle
+ (the cycle of the last data sample).
+ This parameter has no affect on DEV_OEn de-assertion.
+ DEV_OEn is always de-asserted the next cycle after
+ last data sampled. Also this parameter has no
+ affect on <turn-off-ps> parameter.
+ Set <rd-hold-ps> to a value smaller than <turn-off-ps>.
+
+Write parameters:
+
+ - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle
+ to the DEV_WEn assertion.
+
+ - devbus,wr-low-ps: Defines the time during which DEV_WEn is active.
+ A[2:0] and Data are kept valid as long as DEV_WEn
+ is active. This parameter defines the setup time of
+ address and data to DEV_WEn rise.
+
+ - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept
+ inactive (high) between data beats of a burst write.
+ DEV_A[2:0] and Data are kept valid (do not toggle) for
+ <wr-high-ps> - <tick> ps.
+ This parameter defines the hold time of address and
+ data after DEV_WEn rise.
+
+ - devbus,sync-enable: Synchronous device enable.
+ 1: True
+ 0: False
+
+An example for an Armada XP GP board, with a 16 MiB NOR device as child
+is showed below. Note that the Device Bus driver is in charge of allocating
+the mbus address decoding window for each of its child devices.
+The window is created using the chip select specified in the child
+device node together with the base address and size specified in the ranges
+property. For instance, in the example below the allocated decoding window
+will start at base address 0xf0000000, with a size 0x1000000 (16 MiB)
+for chip select 0 (a.k.a DEV_BOOTCS).
+
+This address window handling is done in this mvebu-devbus only as a temporary
+solution. It will be removed when the support for mbus device tree binding is
+added.
+
+The reg property implicitly specifies the chip select as this:
+
+ 0x10400: DEV_BOOTCS
+ 0x10408: DEV_CS0
+ 0x10410: DEV_CS1
+ 0x10418: DEV_CS2
+ 0x10420: DEV_CS3
+
+Example:
+
+ devbus-bootcs@d0010400 {
+ status = "okay";
+ ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ flash@0 {
+ compatible = "cfi-flash";
+
+ /* 16 MiB */
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * We split the 16 MiB in two partitions,
+ * just as an example.
+ */
+ partition@0 {
+ label = "First";
+ reg = <0 0x800000>;
+ };
+
+ partition@800000 {
+ label = "Second";
+ reg = <0x800000 0x800000>;
+ };
+ };
+ };
diff --git a/Documentation/w1/w1.generic b/Documentation/w1/w1.generic
index 212f4ac..a31c5a2 100644
--- a/Documentation/w1/w1.generic
+++ b/Documentation/w1/w1.generic
@@ -25,8 +25,8 @@
- sysfs entries for that w1 master are created
- the w1 bus is periodically searched for new slave devices
-When a device is found on the bus, w1 core checks if driver for its family is
-loaded. If so, the family driver is attached to the slave.
+When a device is found on the bus, w1 core tries to load the driver for its family
+and check if it is loaded. If so, the family driver is attached to the slave.
If there is no driver for the family, default one is assigned, which allows to perform
almost any kind of operations. Each logical operation is a transaction
in nature, which can contain several (two or one) low-level operations.
diff --git a/drivers/char/mem.c b/drivers/char/mem.c
index 1ccbe94..2ca6d78 100644
--- a/drivers/char/mem.c
+++ b/drivers/char/mem.c
@@ -745,7 +745,7 @@
offset += file->f_pos;
case SEEK_SET:
/* to avoid userland mistaking f_pos=-9 as -EBADF=-9 */
- if ((unsigned long long)offset >= ~0xFFFULL) {
+ if (IS_ERR_VALUE((unsigned long long)offset)) {
ret = -EOVERFLOW;
break;
}
diff --git a/drivers/char/mspec.c b/drivers/char/mspec.c
index e1f60f9..f1d7fa4 100644
--- a/drivers/char/mspec.c
+++ b/drivers/char/mspec.c
@@ -267,7 +267,7 @@
if ((vma->vm_flags & VM_WRITE) == 0)
return -EPERM;
- pages = (vma->vm_end - vma->vm_start) >> PAGE_SHIFT;
+ pages = vma_pages(vma);
vdata_size = sizeof(struct vma_data) + pages * sizeof(long);
if (vdata_size <= PAGE_SIZE)
vdata = kzalloc(vdata_size, GFP_KERNEL);
diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.h b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
index d31ee23..38b145e 100644
--- a/drivers/char/xilinx_hwicap/xilinx_hwicap.h
+++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
@@ -37,7 +37,7 @@
#include <linux/cdev.h>
#include <linux/platform_device.h>
-#include <asm/io.h>
+#include <linux/io.h>
struct hwicap_drvdata {
u32 write_buffer_in_use; /* Always in [0,3] */
@@ -85,7 +85,13 @@
void (*reset)(struct hwicap_drvdata *drvdata);
};
-/* Number of times to poll the done regsiter */
+/* Number of times to poll the done register. This has to be large
+ * enough to allow an entire configuration to complete. If an entire
+ * page (4kb) is configured at once, that could take up to 4k cycles
+ * with a byte-wide icap interface. In most cases, this driver is
+ * used with a much smaller fifo, but this should be sufficient in the
+ * worst case.
+ */
#define XHI_MAX_RETRIES 5000
/************ Constant Definitions *************/
diff --git a/drivers/hv/channel.c b/drivers/hv/channel.c
index 0b122f8..6de6c98 100644
--- a/drivers/hv/channel.c
+++ b/drivers/hv/channel.c
@@ -116,6 +116,15 @@
unsigned long flags;
int ret, t, err = 0;
+ spin_lock_irqsave(&newchannel->sc_lock, flags);
+ if (newchannel->state == CHANNEL_OPEN_STATE) {
+ newchannel->state = CHANNEL_OPENING_STATE;
+ } else {
+ spin_unlock_irqrestore(&newchannel->sc_lock, flags);
+ return -EINVAL;
+ }
+ spin_unlock_irqrestore(&newchannel->sc_lock, flags);
+
newchannel->onchannel_callback = onchannelcallback;
newchannel->channel_callback_context = context;
@@ -216,6 +225,9 @@
list_del(&open_info->msglistentry);
spin_unlock_irqrestore(&vmbus_connection.channelmsg_lock, flags);
+ if (err == 0)
+ newchannel->state = CHANNEL_OPENED_STATE;
+
kfree(open_info);
return err;
@@ -500,15 +512,14 @@
}
EXPORT_SYMBOL_GPL(vmbus_teardown_gpadl);
-/*
- * vmbus_close - Close the specified channel
- */
-void vmbus_close(struct vmbus_channel *channel)
+static void vmbus_close_internal(struct vmbus_channel *channel)
{
struct vmbus_channel_close_channel *msg;
int ret;
unsigned long flags;
+ channel->state = CHANNEL_OPEN_STATE;
+ channel->sc_creation_callback = NULL;
/* Stop callback and cancel the timer asap */
spin_lock_irqsave(&channel->inbound_lock, flags);
channel->onchannel_callback = NULL;
@@ -538,6 +549,37 @@
}
+
+/*
+ * vmbus_close - Close the specified channel
+ */
+void vmbus_close(struct vmbus_channel *channel)
+{
+ struct list_head *cur, *tmp;
+ struct vmbus_channel *cur_channel;
+
+ if (channel->primary_channel != NULL) {
+ /*
+ * We will only close sub-channels when
+ * the primary is closed.
+ */
+ return;
+ }
+ /*
+ * Close all the sub-channels first and then close the
+ * primary channel.
+ */
+ list_for_each_safe(cur, tmp, &channel->sc_list) {
+ cur_channel = list_entry(cur, struct vmbus_channel, sc_list);
+ if (cur_channel->state != CHANNEL_OPENED_STATE)
+ continue;
+ vmbus_close_internal(cur_channel);
+ }
+ /*
+ * Now close the primary.
+ */
+ vmbus_close_internal(channel);
+}
EXPORT_SYMBOL_GPL(vmbus_close);
/**
diff --git a/drivers/hv/channel_mgmt.c b/drivers/hv/channel_mgmt.c
index 21ef689..0df7590 100644
--- a/drivers/hv/channel_mgmt.c
+++ b/drivers/hv/channel_mgmt.c
@@ -115,6 +115,9 @@
return NULL;
spin_lock_init(&channel->inbound_lock);
+ spin_lock_init(&channel->sc_lock);
+
+ INIT_LIST_HEAD(&channel->sc_list);
channel->controlwq = create_workqueue("hv_vmbus_ctl");
if (!channel->controlwq) {
@@ -166,6 +169,7 @@
struct vmbus_channel,
work);
unsigned long flags;
+ struct vmbus_channel *primary_channel;
struct vmbus_channel_relid_released msg;
vmbus_device_unregister(channel->device_obj);
@@ -174,9 +178,16 @@
msg.header.msgtype = CHANNELMSG_RELID_RELEASED;
vmbus_post_msg(&msg, sizeof(struct vmbus_channel_relid_released));
- spin_lock_irqsave(&vmbus_connection.channel_lock, flags);
- list_del(&channel->listentry);
- spin_unlock_irqrestore(&vmbus_connection.channel_lock, flags);
+ if (channel->primary_channel == NULL) {
+ spin_lock_irqsave(&vmbus_connection.channel_lock, flags);
+ list_del(&channel->listentry);
+ spin_unlock_irqrestore(&vmbus_connection.channel_lock, flags);
+ } else {
+ primary_channel = channel->primary_channel;
+ spin_lock_irqsave(&primary_channel->sc_lock, flags);
+ list_del(&channel->listentry);
+ spin_unlock_irqrestore(&primary_channel->sc_lock, flags);
+ }
free_channel(channel);
}
@@ -228,6 +239,24 @@
spin_unlock_irqrestore(&vmbus_connection.channel_lock, flags);
if (!fnew) {
+ /*
+ * Check to see if this is a sub-channel.
+ */
+ if (newchannel->offermsg.offer.sub_channel_index != 0) {
+ /*
+ * Process the sub-channel.
+ */
+ newchannel->primary_channel = channel;
+ spin_lock_irqsave(&channel->sc_lock, flags);
+ list_add_tail(&newchannel->sc_list, &channel->sc_list);
+ spin_unlock_irqrestore(&channel->sc_lock, flags);
+ newchannel->state = CHANNEL_OPEN_STATE;
+ if (channel->sc_creation_callback != NULL)
+ channel->sc_creation_callback(newchannel);
+
+ return;
+ }
+
free_channel(newchannel);
return;
}
@@ -685,4 +714,86 @@
return ret;
}
-/* eof */
+/*
+ * Retrieve the (sub) channel on which to send an outgoing request.
+ * When a primary channel has multiple sub-channels, we choose a
+ * channel whose VCPU binding is closest to the VCPU on which
+ * this call is being made.
+ */
+struct vmbus_channel *vmbus_get_outgoing_channel(struct vmbus_channel *primary)
+{
+ struct list_head *cur, *tmp;
+ int cur_cpu = hv_context.vp_index[smp_processor_id()];
+ struct vmbus_channel *cur_channel;
+ struct vmbus_channel *outgoing_channel = primary;
+ int cpu_distance, new_cpu_distance;
+
+ if (list_empty(&primary->sc_list))
+ return outgoing_channel;
+
+ list_for_each_safe(cur, tmp, &primary->sc_list) {
+ cur_channel = list_entry(cur, struct vmbus_channel, sc_list);
+ if (cur_channel->state != CHANNEL_OPENED_STATE)
+ continue;
+
+ if (cur_channel->target_vp == cur_cpu)
+ return cur_channel;
+
+ cpu_distance = ((outgoing_channel->target_vp > cur_cpu) ?
+ (outgoing_channel->target_vp - cur_cpu) :
+ (cur_cpu - outgoing_channel->target_vp));
+
+ new_cpu_distance = ((cur_channel->target_vp > cur_cpu) ?
+ (cur_channel->target_vp - cur_cpu) :
+ (cur_cpu - cur_channel->target_vp));
+
+ if (cpu_distance < new_cpu_distance)
+ continue;
+
+ outgoing_channel = cur_channel;
+ }
+
+ return outgoing_channel;
+}
+EXPORT_SYMBOL_GPL(vmbus_get_outgoing_channel);
+
+static void invoke_sc_cb(struct vmbus_channel *primary_channel)
+{
+ struct list_head *cur, *tmp;
+ struct vmbus_channel *cur_channel;
+
+ if (primary_channel->sc_creation_callback == NULL)
+ return;
+
+ list_for_each_safe(cur, tmp, &primary_channel->sc_list) {
+ cur_channel = list_entry(cur, struct vmbus_channel, sc_list);
+
+ primary_channel->sc_creation_callback(cur_channel);
+ }
+}
+
+void vmbus_set_sc_create_callback(struct vmbus_channel *primary_channel,
+ void (*sc_cr_cb)(struct vmbus_channel *new_sc))
+{
+ primary_channel->sc_creation_callback = sc_cr_cb;
+}
+EXPORT_SYMBOL_GPL(vmbus_set_sc_create_callback);
+
+bool vmbus_are_subchannels_present(struct vmbus_channel *primary)
+{
+ bool ret;
+
+ ret = !list_empty(&primary->sc_list);
+
+ if (ret) {
+ /*
+ * Invoke the callback on sub-channel creation.
+ * This will present a uniform interface to the
+ * clients.
+ */
+ invoke_sc_cb(primary);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(vmbus_are_subchannels_present);
diff --git a/drivers/hv/connection.c b/drivers/hv/connection.c
index 253a74b..ec3b8cd 100644
--- a/drivers/hv/connection.c
+++ b/drivers/hv/connection.c
@@ -246,12 +246,26 @@
struct vmbus_channel *channel;
struct vmbus_channel *found_channel = NULL;
unsigned long flags;
+ struct list_head *cur, *tmp;
+ struct vmbus_channel *cur_sc;
spin_lock_irqsave(&vmbus_connection.channel_lock, flags);
list_for_each_entry(channel, &vmbus_connection.chn_list, listentry) {
if (channel->offermsg.child_relid == relid) {
found_channel = channel;
break;
+ } else if (!list_empty(&channel->sc_list)) {
+ /*
+ * Deal with sub-channels.
+ */
+ list_for_each_safe(cur, tmp, &channel->sc_list) {
+ cur_sc = list_entry(cur, struct vmbus_channel,
+ sc_list);
+ if (cur_sc->offermsg.child_relid == relid) {
+ found_channel = cur_sc;
+ break;
+ }
+ }
}
}
spin_unlock_irqrestore(&vmbus_connection.channel_lock, flags);
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 067f311..29a11db 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -20,6 +20,16 @@
parameters and other settings during frequency, voltage and
temperature changes
+config MVEBU_DEVBUS
+ bool "Marvell EBU Device Bus Controller"
+ default y
+ depends on PLAT_ORION && OF
+ help
+ This driver is for the Device Bus controller available in some
+ Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and
+ Armada 370 and Armada XP. This controller allows to handle flash
+ devices such as NOR, NAND, SRAM, and FPGA.
+
config TEGRA20_MC
bool "Tegra20 Memory Controller(MC) driver"
default y
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index 9cce5d7..969d923 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -6,5 +6,6 @@
obj-$(CONFIG_OF) += of_memory.o
endif
obj-$(CONFIG_TI_EMIF) += emif.o
+obj-$(CONFIG_MVEBU_DEVBUS) += mvebu-devbus.o
obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o
obj-$(CONFIG_TEGRA30_MC) += tegra30-mc.o
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
new file mode 100644
index 0000000..978e8e3
--- /dev/null
+++ b/drivers/memory/mvebu-devbus.c
@@ -0,0 +1,340 @@
+/*
+ * Marvell EBU SoC Device Bus Controller
+ * (memory controller for NOR/NAND/SRAM/FPGA devices)
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/mbus.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+/* Register definitions */
+#define DEV_WIDTH_BIT 30
+#define BADR_SKEW_BIT 28
+#define RD_HOLD_BIT 23
+#define ACC_NEXT_BIT 17
+#define RD_SETUP_BIT 12
+#define ACC_FIRST_BIT 6
+
+#define SYNC_ENABLE_BIT 24
+#define WR_HIGH_BIT 16
+#define WR_LOW_BIT 8
+
+#define READ_PARAM_OFFSET 0x0
+#define WRITE_PARAM_OFFSET 0x4
+
+static const char * const devbus_wins[] = {
+ "devbus-boot",
+ "devbus-cs0",
+ "devbus-cs1",
+ "devbus-cs2",
+ "devbus-cs3",
+};
+
+struct devbus_read_params {
+ u32 bus_width;
+ u32 badr_skew;
+ u32 turn_off;
+ u32 acc_first;
+ u32 acc_next;
+ u32 rd_setup;
+ u32 rd_hold;
+};
+
+struct devbus_write_params {
+ u32 sync_enable;
+ u32 wr_high;
+ u32 wr_low;
+ u32 ale_wr;
+};
+
+struct devbus {
+ struct device *dev;
+ void __iomem *base;
+ unsigned long tick_ps;
+};
+
+static int get_timing_param_ps(struct devbus *devbus,
+ struct device_node *node,
+ const char *name,
+ u32 *ticks)
+{
+ u32 time_ps;
+ int err;
+
+ err = of_property_read_u32(node, name, &time_ps);
+ if (err < 0) {
+ dev_err(devbus->dev, "%s has no '%s' property\n",
+ name, node->full_name);
+ return err;
+ }
+
+ *ticks = (time_ps + devbus->tick_ps - 1) / devbus->tick_ps;
+
+ dev_dbg(devbus->dev, "%s: %u ps -> 0x%x\n",
+ name, time_ps, *ticks);
+ return 0;
+}
+
+static int devbus_set_timing_params(struct devbus *devbus,
+ struct device_node *node)
+{
+ struct devbus_read_params r;
+ struct devbus_write_params w;
+ u32 value;
+ int err;
+
+ dev_dbg(devbus->dev, "Setting timing parameter, tick is %lu ps\n",
+ devbus->tick_ps);
+
+ /* Get read timings */
+ err = of_property_read_u32(node, "devbus,bus-width", &r.bus_width);
+ if (err < 0) {
+ dev_err(devbus->dev,
+ "%s has no 'devbus,bus-width' property\n",
+ node->full_name);
+ return err;
+ }
+ /* Convert bit width to byte width */
+ r.bus_width /= 8;
+
+ err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
+ &r.badr_skew);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,turn-off-ps",
+ &r.turn_off);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,acc-first-ps",
+ &r.acc_first);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,acc-next-ps",
+ &r.acc_next);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,rd-setup-ps",
+ &r.rd_setup);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,rd-hold-ps",
+ &r.rd_hold);
+ if (err < 0)
+ return err;
+
+ /* Get write timings */
+ err = of_property_read_u32(node, "devbus,sync-enable",
+ &w.sync_enable);
+ if (err < 0) {
+ dev_err(devbus->dev,
+ "%s has no 'devbus,sync-enable' property\n",
+ node->full_name);
+ return err;
+ }
+
+ err = get_timing_param_ps(devbus, node, "devbus,ale-wr-ps",
+ &w.ale_wr);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,wr-low-ps",
+ &w.wr_low);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,wr-high-ps",
+ &w.wr_high);
+ if (err < 0)
+ return err;
+
+ /* Set read timings */
+ value = r.bus_width << DEV_WIDTH_BIT |
+ r.badr_skew << BADR_SKEW_BIT |
+ r.rd_hold << RD_HOLD_BIT |
+ r.acc_next << ACC_NEXT_BIT |
+ r.rd_setup << RD_SETUP_BIT |
+ r.acc_first << ACC_FIRST_BIT |
+ r.turn_off;
+
+ dev_dbg(devbus->dev, "read parameters register 0x%p = 0x%x\n",
+ devbus->base + READ_PARAM_OFFSET,
+ value);
+
+ writel(value, devbus->base + READ_PARAM_OFFSET);
+
+ /* Set write timings */
+ value = w.sync_enable << SYNC_ENABLE_BIT |
+ w.wr_low << WR_LOW_BIT |
+ w.wr_high << WR_HIGH_BIT |
+ w.ale_wr;
+
+ dev_dbg(devbus->dev, "write parameters register: 0x%p = 0x%x\n",
+ devbus->base + WRITE_PARAM_OFFSET,
+ value);
+
+ writel(value, devbus->base + WRITE_PARAM_OFFSET);
+
+ return 0;
+}
+
+static int mvebu_devbus_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *node = pdev->dev.of_node;
+ struct device_node *parent;
+ struct devbus *devbus;
+ struct resource *res;
+ struct clk *clk;
+ unsigned long rate;
+ const __be32 *ranges;
+ int err, cs;
+ int addr_cells, p_addr_cells, size_cells;
+ int ranges_len, tuple_len;
+ u32 base, size;
+
+ devbus = devm_kzalloc(&pdev->dev, sizeof(struct devbus), GFP_KERNEL);
+ if (!devbus)
+ return -ENOMEM;
+
+ devbus->dev = dev;
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ devbus->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(devbus->base))
+ return PTR_ERR(devbus->base);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ clk_prepare_enable(clk);
+
+ /*
+ * Obtain clock period in picoseconds,
+ * we need this in order to convert timing
+ * parameters from cycles to picoseconds.
+ */
+ rate = clk_get_rate(clk) / 1000;
+ devbus->tick_ps = 1000000000 / rate;
+
+ /* Read the device tree node and set the new timing parameters */
+ err = devbus_set_timing_params(devbus, node);
+ if (err < 0)
+ return err;
+
+ /*
+ * Allocate an address window for this device.
+ * If the device probing fails, then we won't be able to
+ * remove the allocated address decoding window.
+ *
+ * FIXME: This is only a temporary hack! We need to do this here
+ * because we still don't have device tree bindings for mbus.
+ * Once that support is added, we will declare these address windows
+ * statically in the device tree, and remove the window configuration
+ * from here.
+ */
+
+ /*
+ * Get the CS to choose the window string.
+ * This is a bit hacky, but it will be removed once the
+ * address windows are declared in the device tree.
+ */
+ cs = (((unsigned long)devbus->base) % 0x400) / 8;
+
+ /*
+ * Parse 'ranges' property to obtain a (base,size) window tuple.
+ * This will be removed once the address windows
+ * are declared in the device tree.
+ */
+ parent = of_get_parent(node);
+ if (!parent)
+ return -EINVAL;
+
+ p_addr_cells = of_n_addr_cells(parent);
+ of_node_put(parent);
+
+ addr_cells = of_n_addr_cells(node);
+ size_cells = of_n_size_cells(node);
+ tuple_len = (p_addr_cells + addr_cells + size_cells) * sizeof(__be32);
+
+ ranges = of_get_property(node, "ranges", &ranges_len);
+ if (ranges == NULL || ranges_len != tuple_len)
+ return -EINVAL;
+
+ base = of_translate_address(node, ranges + addr_cells);
+ if (base == OF_BAD_ADDR)
+ return -EINVAL;
+ size = of_read_number(ranges + addr_cells + p_addr_cells, size_cells);
+
+ /*
+ * Create an mbus address windows.
+ * FIXME: Remove this, together with the above code, once the
+ * address windows are declared in the device tree.
+ */
+ err = mvebu_mbus_add_window(devbus_wins[cs], base, size);
+ if (err < 0)
+ return err;
+
+ /*
+ * We need to create a child device explicitly from here to
+ * guarantee that the child will be probed after the timing
+ * parameters for the bus are written.
+ */
+ err = of_platform_populate(node, NULL, NULL, dev);
+ if (err < 0) {
+ mvebu_mbus_del_window(base, size);
+ return err;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id mvebu_devbus_of_match[] = {
+ { .compatible = "marvell,mvebu-devbus" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mvebu_devbus_of_match);
+
+static struct platform_driver mvebu_devbus_driver = {
+ .probe = mvebu_devbus_probe,
+ .driver = {
+ .name = "mvebu-devbus",
+ .owner = THIS_MODULE,
+ .of_match_table = mvebu_devbus_of_match,
+ },
+};
+
+static int __init mvebu_devbus_init(void)
+{
+ return platform_driver_register(&mvebu_devbus_driver);
+}
+module_init(mvebu_devbus_init);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Ezequiel Garcia <ezequiel.garcia@free-electrons.com>");
+MODULE_DESCRIPTION("Marvell EBU SoC Device Bus controller");
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index c002d86..80889d5 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -480,6 +480,7 @@
config PCH_PHUB
tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
+ select GENERIC_NET_UTILS
depends on PCI
help
This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
diff --git a/drivers/misc/ad525x_dpot.c b/drivers/misc/ad525x_dpot.c
index 8f99e8e..0daadcf 100644
--- a/drivers/misc/ad525x_dpot.c
+++ b/drivers/misc/ad525x_dpot.c
@@ -470,7 +470,7 @@
!test_bit(DPOT_RDAC_MASK & reg, data->otp_en_mask))
return -EPERM;
- err = strict_strtoul(buf, 10, &value);
+ err = kstrtoul(buf, 10, &value);
if (err)
return err;
diff --git a/drivers/misc/apds9802als.c b/drivers/misc/apds9802als.c
index 5b5fd84..0c6e037 100644
--- a/drivers/misc/apds9802als.c
+++ b/drivers/misc/apds9802als.c
@@ -126,8 +126,9 @@
int ret_val;
unsigned long val;
- if (strict_strtoul(buf, 10, &val))
- return -EINVAL;
+ ret_val = kstrtoul(buf, 10, &val);
+ if (ret_val)
+ return ret_val;
if (val < 4096)
val = 1;
diff --git a/drivers/misc/apds990x.c b/drivers/misc/apds990x.c
index 98f9bb2..868a30a 100644
--- a/drivers/misc/apds990x.c
+++ b/drivers/misc/apds990x.c
@@ -696,9 +696,11 @@
{
struct apds990x_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
chip->lux_calib = value;
@@ -759,8 +761,9 @@
unsigned long value;
int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
ret = apds990x_set_arate(chip, value);
@@ -813,9 +816,11 @@
{
struct apds990x_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
@@ -892,11 +897,12 @@
static ssize_t apds990x_set_lux_thresh(struct apds990x_chip *chip, u32 *target,
const char *buf)
{
- int ret = 0;
unsigned long thresh;
+ int ret;
- if (strict_strtoul(buf, 0, &thresh))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &thresh);
+ if (ret)
+ return ret;
if (thresh > APDS_RANGE)
return -EINVAL;
@@ -957,9 +963,11 @@
{
struct apds990x_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
if ((value > APDS_RANGE) || (value == 0) ||
(value < APDS_PROX_HYSTERESIS))
@@ -990,9 +998,12 @@
{
struct apds990x_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
+
if (value) {
pm_runtime_get_sync(dev);
mutex_lock(&chip->mutex);
diff --git a/drivers/misc/arm-charlcd.c b/drivers/misc/arm-charlcd.c
index 48651ef..1256a4b 100644
--- a/drivers/misc/arm-charlcd.c
+++ b/drivers/misc/arm-charlcd.c
@@ -291,7 +291,7 @@
lcd->virtbase = ioremap(lcd->phybase, lcd->physize);
if (!lcd->virtbase) {
ret = -ENOMEM;
- goto out_no_remap;
+ goto out_no_memregion;
}
lcd->irq = platform_get_irq(pdev, 0);
@@ -320,8 +320,6 @@
out_no_irq:
iounmap(lcd->virtbase);
-out_no_remap:
- platform_set_drvdata(pdev, NULL);
out_no_memregion:
release_mem_region(lcd->phybase, SZ_4K);
out_no_resource:
@@ -337,7 +335,6 @@
free_irq(lcd->irq, lcd);
iounmap(lcd->virtbase);
release_mem_region(lcd->phybase, lcd->physize);
- platform_set_drvdata(pdev, NULL);
kfree(lcd);
}
diff --git a/drivers/misc/bh1770glc.c b/drivers/misc/bh1770glc.c
index f4975f7..99a0468 100644
--- a/drivers/misc/bh1770glc.c
+++ b/drivers/misc/bh1770glc.c
@@ -651,8 +651,9 @@
unsigned long value;
ssize_t ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
if (value) {
@@ -726,9 +727,11 @@
{
struct bh1770_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
/* Assume no proximity. Sensor will tell real state soon */
@@ -824,9 +827,11 @@
{
struct bh1770_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
chip->prox_rate_threshold = bh1770_prox_rate_validate(value);
@@ -840,9 +845,11 @@
{
struct bh1770_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
chip->prox_rate = bh1770_prox_rate_validate(value);
@@ -865,8 +872,10 @@
unsigned long value;
int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
+
if (value > BH1770_PROX_RANGE)
return -EINVAL;
@@ -893,9 +902,11 @@
{
struct bh1770_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
if (value > BH1770_PROX_MAX_PERSISTENCE)
return -EINVAL;
@@ -918,9 +929,11 @@
{
struct bh1770_chip *chip = dev_get_drvdata(dev);
unsigned long value;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
if (value > BH1770_PROX_RANGE)
return -EINVAL;
@@ -963,9 +976,11 @@
unsigned long value;
u32 old_calib;
u32 new_corr;
+ int ret;
- if (strict_strtoul(buf, 0, &value))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &value);
+ if (ret)
+ return ret;
mutex_lock(&chip->mutex);
old_calib = chip->lux_calib;
@@ -1012,8 +1027,9 @@
unsigned long rate_hz;
int ret, i;
- if (strict_strtoul(buf, 0, &rate_hz))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &rate_hz);
+ if (ret)
+ return ret;
for (i = 0; i < ARRAY_SIZE(lux_rates_hz) - 1; i++)
if (rate_hz >= lux_rates_hz[i])
@@ -1047,11 +1063,12 @@
static ssize_t bh1770_set_lux_thresh(struct bh1770_chip *chip, u16 *target,
const char *buf)
{
- int ret = 0;
unsigned long thresh;
+ int ret;
- if (strict_strtoul(buf, 0, &thresh))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &thresh);
+ if (ret)
+ return ret;
if (thresh > BH1770_LUX_RANGE)
return -EINVAL;
diff --git a/drivers/misc/bh1780gli.c b/drivers/misc/bh1780gli.c
index 818f3a0..057580e 100644
--- a/drivers/misc/bh1780gli.c
+++ b/drivers/misc/bh1780gli.c
@@ -107,7 +107,7 @@
unsigned long val;
int error;
- error = strict_strtoul(buf, 0, &val);
+ error = kstrtoul(buf, 0, &val);
if (error)
return error;
diff --git a/drivers/misc/carma/carma-fpga-program.c b/drivers/misc/carma/carma-fpga-program.c
index 736c771..c6bd7e8 100644
--- a/drivers/misc/carma/carma-fpga-program.c
+++ b/drivers/misc/carma/carma-fpga-program.c
@@ -830,8 +830,9 @@
unsigned long val;
int ret;
- if (strict_strtoul(buf, 0, &val))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &val);
+ if (ret)
+ return ret;
if (val) {
ret = fpga_enable_power_supplies(priv);
@@ -859,8 +860,9 @@
unsigned long val;
int ret;
- if (strict_strtoul(buf, 0, &val))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &val);
+ if (ret)
+ return ret;
/* We can't have an image writer and be programming simultaneously */
if (mutex_lock_interruptible(&priv->lock))
@@ -919,7 +921,7 @@
static int fpga_of_remove(struct platform_device *op)
{
- struct fpga_dev *priv = dev_get_drvdata(&op->dev);
+ struct fpga_dev *priv = platform_get_drvdata(op);
struct device *this_device = priv->miscdev.this_device;
sysfs_remove_group(&this_device->kobj, &fpga_attr_group);
@@ -969,7 +971,7 @@
kref_init(&priv->ref);
- dev_set_drvdata(&op->dev, priv);
+ platform_set_drvdata(op, priv);
priv->dev = &op->dev;
mutex_init(&priv->lock);
init_completion(&priv->completion);
diff --git a/drivers/misc/carma/carma-fpga.c b/drivers/misc/carma/carma-fpga.c
index 7508caf..7b56563f 100644
--- a/drivers/misc/carma/carma-fpga.c
+++ b/drivers/misc/carma/carma-fpga.c
@@ -1002,10 +1002,10 @@
unsigned long enable;
int ret;
- ret = strict_strtoul(buf, 0, &enable);
+ ret = kstrtoul(buf, 0, &enable);
if (ret) {
dev_err(priv->dev, "unable to parse enable input\n");
- return -EINVAL;
+ return ret;
}
/* protect against concurrent enable/disable */
@@ -1296,7 +1296,7 @@
goto out_return;
}
- dev_set_drvdata(&op->dev, priv);
+ platform_set_drvdata(op, priv);
priv->dev = &op->dev;
kref_init(&priv->ref);
mutex_init(&priv->mutex);
@@ -1400,7 +1400,7 @@
static int data_of_remove(struct platform_device *op)
{
- struct fpga_device *priv = dev_get_drvdata(&op->dev);
+ struct fpga_device *priv = platform_get_drvdata(op);
struct device *this_device = priv->miscdev.this_device;
/* remove all sysfs files, now the device cannot be re-enabled */
diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c
index 2baeec5..5d4fd69 100644
--- a/drivers/misc/eeprom/at24.c
+++ b/drivers/misc/eeprom/at24.c
@@ -492,10 +492,9 @@
if (client->dev.platform_data) {
chip = *(struct at24_platform_data *)client->dev.platform_data;
} else {
- if (!id->driver_data) {
- err = -ENODEV;
- goto err_out;
- }
+ if (!id->driver_data)
+ return -ENODEV;
+
magic = id->driver_data;
chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
magic >>= AT24_SIZE_BYTELEN;
@@ -519,8 +518,7 @@
"byte_len looks suspicious (no power of 2)!\n");
if (!chip.page_size) {
dev_err(&client->dev, "page_size must not be 0!\n");
- err = -EINVAL;
- goto err_out;
+ return -EINVAL;
}
if (!is_power_of_2(chip.page_size))
dev_warn(&client->dev,
@@ -528,10 +526,9 @@
/* Use I2C operations unless we're stuck with SMBus extensions. */
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
- if (chip.flags & AT24_FLAG_ADDR16) {
- err = -EPFNOSUPPORT;
- goto err_out;
- }
+ if (chip.flags & AT24_FLAG_ADDR16)
+ return -EPFNOSUPPORT;
+
if (i2c_check_functionality(client->adapter,
I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
use_smbus = I2C_SMBUS_I2C_BLOCK_DATA;
@@ -542,8 +539,7 @@
I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
use_smbus = I2C_SMBUS_BYTE_DATA;
} else {
- err = -EPFNOSUPPORT;
- goto err_out;
+ return -EPFNOSUPPORT;
}
}
@@ -553,12 +549,10 @@
num_addresses = DIV_ROUND_UP(chip.byte_len,
(chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
- at24 = kzalloc(sizeof(struct at24_data) +
+ at24 = devm_kzalloc(&client->dev, sizeof(struct at24_data) +
num_addresses * sizeof(struct i2c_client *), GFP_KERNEL);
- if (!at24) {
- err = -ENOMEM;
- goto err_out;
- }
+ if (!at24)
+ return -ENOMEM;
mutex_init(&at24->lock);
at24->use_smbus = use_smbus;
@@ -596,11 +590,10 @@
at24->write_max = write_max;
/* buffer (data + address at the beginning) */
- at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL);
- if (!at24->writebuf) {
- err = -ENOMEM;
- goto err_struct;
- }
+ at24->writebuf = devm_kzalloc(&client->dev,
+ write_max + 2, GFP_KERNEL);
+ if (!at24->writebuf)
+ return -ENOMEM;
} else {
dev_warn(&client->dev,
"cannot write due to controller restrictions.");
@@ -648,11 +641,6 @@
if (at24->client[i])
i2c_unregister_device(at24->client[i]);
- kfree(at24->writebuf);
-err_struct:
- kfree(at24);
-err_out:
- dev_dbg(&client->dev, "probe error %d\n", err);
return err;
}
@@ -667,8 +655,6 @@
for (i = 1; i < at24->num_addresses; i++)
i2c_unregister_device(at24->client[i]);
- kfree(at24->writebuf);
- kfree(at24);
return 0;
}
diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c
index ad8fd8e..840b359 100644
--- a/drivers/misc/eeprom/at25.c
+++ b/drivers/misc/eeprom/at25.c
@@ -371,11 +371,10 @@
if (np) {
err = at25_np_to_chip(&spi->dev, np, &chip);
if (err)
- goto fail;
+ return err;
} else {
dev_err(&spi->dev, "Error: no chip description\n");
- err = -ENODEV;
- goto fail;
+ return -ENODEV;
}
} else
chip = *(struct spi_eeprom *)spi->dev.platform_data;
@@ -389,8 +388,7 @@
addrlen = 3;
else {
dev_dbg(&spi->dev, "unsupported address type\n");
- err = -EINVAL;
- goto fail;
+ return -EINVAL;
}
/* Ping the chip ... the status register is pretty portable,
@@ -400,14 +398,12 @@
sr = spi_w8r8(spi, AT25_RDSR);
if (sr < 0 || sr & AT25_SR_nRDY) {
dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
- err = -ENXIO;
- goto fail;
+ return -ENXIO;
}
- if (!(at25 = kzalloc(sizeof *at25, GFP_KERNEL))) {
- err = -ENOMEM;
- goto fail;
- }
+ at25 = devm_kzalloc(&spi->dev, sizeof(struct at25_data), GFP_KERNEL);
+ if (!at25)
+ return -ENOMEM;
mutex_init(&at25->lock);
at25->chip = chip;
@@ -439,7 +435,7 @@
err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin);
if (err)
- goto fail;
+ return err;
if (chip.setup)
chip.setup(&at25->mem, chip.context);
@@ -453,10 +449,6 @@
(chip.flags & EE_READONLY) ? " (readonly)" : "",
at25->chip.page_size);
return 0;
-fail:
- dev_dbg(&spi->dev, "probe err %d\n", err);
- kfree(at25);
- return err;
}
static int at25_remove(struct spi_device *spi)
@@ -465,7 +457,6 @@
at25 = spi_get_drvdata(spi);
sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin);
- kfree(at25);
return 0;
}
diff --git a/drivers/misc/ep93xx_pwm.c b/drivers/misc/ep93xx_pwm.c
index 96787ec..cdb67a9 100644
--- a/drivers/misc/ep93xx_pwm.c
+++ b/drivers/misc/ep93xx_pwm.c
@@ -39,63 +39,6 @@
u32 duty_percent;
};
-static inline void ep93xx_pwm_writel(struct ep93xx_pwm *pwm,
- unsigned int val, unsigned int off)
-{
- __raw_writel(val, pwm->mmio_base + off);
-}
-
-static inline unsigned int ep93xx_pwm_readl(struct ep93xx_pwm *pwm,
- unsigned int off)
-{
- return __raw_readl(pwm->mmio_base + off);
-}
-
-static inline void ep93xx_pwm_write_tc(struct ep93xx_pwm *pwm, u16 value)
-{
- ep93xx_pwm_writel(pwm, value, EP93XX_PWMx_TERM_COUNT);
-}
-
-static inline u16 ep93xx_pwm_read_tc(struct ep93xx_pwm *pwm)
-{
- return ep93xx_pwm_readl(pwm, EP93XX_PWMx_TERM_COUNT);
-}
-
-static inline void ep93xx_pwm_write_dc(struct ep93xx_pwm *pwm, u16 value)
-{
- ep93xx_pwm_writel(pwm, value, EP93XX_PWMx_DUTY_CYCLE);
-}
-
-static inline void ep93xx_pwm_enable(struct ep93xx_pwm *pwm)
-{
- ep93xx_pwm_writel(pwm, 0x1, EP93XX_PWMx_ENABLE);
-}
-
-static inline void ep93xx_pwm_disable(struct ep93xx_pwm *pwm)
-{
- ep93xx_pwm_writel(pwm, 0x0, EP93XX_PWMx_ENABLE);
-}
-
-static inline int ep93xx_pwm_is_enabled(struct ep93xx_pwm *pwm)
-{
- return ep93xx_pwm_readl(pwm, EP93XX_PWMx_ENABLE) & 0x1;
-}
-
-static inline void ep93xx_pwm_invert(struct ep93xx_pwm *pwm)
-{
- ep93xx_pwm_writel(pwm, 0x1, EP93XX_PWMx_INVERT);
-}
-
-static inline void ep93xx_pwm_normal(struct ep93xx_pwm *pwm)
-{
- ep93xx_pwm_writel(pwm, 0x0, EP93XX_PWMx_INVERT);
-}
-
-static inline int ep93xx_pwm_is_inverted(struct ep93xx_pwm *pwm)
-{
- return ep93xx_pwm_readl(pwm, EP93XX_PWMx_INVERT) & 0x1;
-}
-
/*
* /sys/devices/platform/ep93xx-pwm.N
* /min_freq read-only minimum pwm output frequency
@@ -131,9 +74,9 @@
struct platform_device *pdev = to_platform_device(dev);
struct ep93xx_pwm *pwm = platform_get_drvdata(pdev);
- if (ep93xx_pwm_is_enabled(pwm)) {
+ if (readl(pwm->mmio_base + EP93XX_PWMx_ENABLE) & 0x1) {
unsigned long rate = clk_get_rate(pwm->clk);
- u16 term = ep93xx_pwm_read_tc(pwm);
+ u16 term = readl(pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
return sprintf(buf, "%ld\n", rate / (term + 1));
} else {
@@ -149,12 +92,12 @@
long val;
int err;
- err = strict_strtol(buf, 10, &val);
+ err = kstrtol(buf, 10, &val);
if (err)
return -EINVAL;
if (val == 0) {
- ep93xx_pwm_disable(pwm);
+ writel(0x0, pwm->mmio_base + EP93XX_PWMx_ENABLE);
} else if (val <= (clk_get_rate(pwm->clk) / 2)) {
u32 term, duty;
@@ -164,20 +107,20 @@
if (val < 1)
val = 1;
- term = ep93xx_pwm_read_tc(pwm);
+ term = readl(pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
duty = ((val + 1) * pwm->duty_percent / 100) - 1;
/* If pwm is running, order is important */
if (val > term) {
- ep93xx_pwm_write_tc(pwm, val);
- ep93xx_pwm_write_dc(pwm, duty);
+ writel(val, pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
+ writel(duty, pwm->mmio_base + EP93XX_PWMx_DUTY_CYCLE);
} else {
- ep93xx_pwm_write_dc(pwm, duty);
- ep93xx_pwm_write_tc(pwm, val);
+ writel(duty, pwm->mmio_base + EP93XX_PWMx_DUTY_CYCLE);
+ writel(val, pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
}
- if (!ep93xx_pwm_is_enabled(pwm))
- ep93xx_pwm_enable(pwm);
+ if (!readl(pwm->mmio_base + EP93XX_PWMx_ENABLE) & 0x1)
+ writel(0x1, pwm->mmio_base + EP93XX_PWMx_ENABLE);
} else {
return -EINVAL;
}
@@ -202,13 +145,15 @@
long val;
int err;
- err = strict_strtol(buf, 10, &val);
+ err = kstrtol(buf, 10, &val);
if (err)
return -EINVAL;
if (val > 0 && val < 100) {
- u32 term = ep93xx_pwm_read_tc(pwm);
- ep93xx_pwm_write_dc(pwm, ((term + 1) * val / 100) - 1);
+ u32 term = readl(pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
+ u32 duty = ((term + 1) * val / 100) - 1;
+
+ writel(duty, pwm->mmio_base + EP93XX_PWMx_DUTY_CYCLE);
pwm->duty_percent = val;
return count;
}
@@ -221,8 +166,9 @@
{
struct platform_device *pdev = to_platform_device(dev);
struct ep93xx_pwm *pwm = platform_get_drvdata(pdev);
+ int inverted = readl(pwm->mmio_base + EP93XX_PWMx_INVERT) & 0x1;
- return sprintf(buf, "%d\n", ep93xx_pwm_is_inverted(pwm));
+ return sprintf(buf, "%d\n", inverted);
}
static ssize_t ep93xx_pwm_set_invert(struct device *dev,
@@ -233,14 +179,14 @@
long val;
int err;
- err = strict_strtol(buf, 10, &val);
+ err = kstrtol(buf, 10, &val);
if (err)
return -EINVAL;
if (val == 0)
- ep93xx_pwm_normal(pwm);
+ writel(0x0, pwm->mmio_base + EP93XX_PWMx_INVERT);
else if (val == 1)
- ep93xx_pwm_invert(pwm);
+ writel(0x1, pwm->mmio_base + EP93XX_PWMx_INVERT);
else
return -EINVAL;
@@ -269,89 +215,55 @@
.attrs = ep93xx_pwm_attrs,
};
-static int __init ep93xx_pwm_probe(struct platform_device *pdev)
+static int ep93xx_pwm_probe(struct platform_device *pdev)
{
struct ep93xx_pwm *pwm;
struct resource *res;
- int err;
+ int ret;
- err = ep93xx_pwm_acquire_gpio(pdev);
- if (err)
- return err;
+ pwm = devm_kzalloc(&pdev->dev, sizeof(*pwm), GFP_KERNEL);
+ if (!pwm)
+ return -ENOMEM;
- pwm = kzalloc(sizeof(struct ep93xx_pwm), GFP_KERNEL);
- if (!pwm) {
- err = -ENOMEM;
- goto fail_no_mem;
- }
+ pwm->clk = devm_clk_get(&pdev->dev, "pwm_clk");
+ if (IS_ERR(pwm->clk))
+ return PTR_ERR(pwm->clk);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (res == NULL) {
- err = -ENXIO;
- goto fail_no_mem_resource;
- }
+ pwm->mmio_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(pwm->mmio_base))
+ return PTR_ERR(pwm->mmio_base);
- res = request_mem_region(res->start, resource_size(res), pdev->name);
- if (res == NULL) {
- err = -EBUSY;
- goto fail_no_mem_resource;
- }
+ ret = ep93xx_pwm_acquire_gpio(pdev);
+ if (ret)
+ return ret;
- pwm->mmio_base = ioremap(res->start, resource_size(res));
- if (pwm->mmio_base == NULL) {
- err = -ENXIO;
- goto fail_no_ioremap;
- }
-
- err = sysfs_create_group(&pdev->dev.kobj, &ep93xx_pwm_sysfs_files);
- if (err)
- goto fail_no_sysfs;
-
- pwm->clk = clk_get(&pdev->dev, "pwm_clk");
- if (IS_ERR(pwm->clk)) {
- err = PTR_ERR(pwm->clk);
- goto fail_no_clk;
+ ret = sysfs_create_group(&pdev->dev.kobj, &ep93xx_pwm_sysfs_files);
+ if (ret) {
+ ep93xx_pwm_release_gpio(pdev);
+ return ret;
}
pwm->duty_percent = 50;
- platform_set_drvdata(pdev, pwm);
-
/* disable pwm at startup. Avoids zero value. */
- ep93xx_pwm_disable(pwm);
- ep93xx_pwm_write_tc(pwm, EP93XX_PWM_MAX_COUNT);
- ep93xx_pwm_write_dc(pwm, EP93XX_PWM_MAX_COUNT / 2);
+ writel(0x0, pwm->mmio_base + EP93XX_PWMx_ENABLE);
+ writel(EP93XX_PWM_MAX_COUNT, pwm->mmio_base + EP93XX_PWMx_TERM_COUNT);
+ writel(EP93XX_PWM_MAX_COUNT/2, pwm->mmio_base + EP93XX_PWMx_DUTY_CYCLE);
clk_enable(pwm->clk);
+ platform_set_drvdata(pdev, pwm);
return 0;
-
-fail_no_clk:
- sysfs_remove_group(&pdev->dev.kobj, &ep93xx_pwm_sysfs_files);
-fail_no_sysfs:
- iounmap(pwm->mmio_base);
-fail_no_ioremap:
- release_mem_region(res->start, resource_size(res));
-fail_no_mem_resource:
- kfree(pwm);
-fail_no_mem:
- ep93xx_pwm_release_gpio(pdev);
- return err;
}
-static int __exit ep93xx_pwm_remove(struct platform_device *pdev)
+static int ep93xx_pwm_remove(struct platform_device *pdev)
{
struct ep93xx_pwm *pwm = platform_get_drvdata(pdev);
- struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- ep93xx_pwm_disable(pwm);
+ writel(0x0, pwm->mmio_base + EP93XX_PWMx_ENABLE);
clk_disable(pwm->clk);
- clk_put(pwm->clk);
- platform_set_drvdata(pdev, NULL);
sysfs_remove_group(&pdev->dev.kobj, &ep93xx_pwm_sysfs_files);
- iounmap(pwm->mmio_base);
- release_mem_region(res->start, resource_size(res));
- kfree(pwm);
ep93xx_pwm_release_gpio(pdev);
return 0;
@@ -362,10 +274,10 @@
.name = "ep93xx-pwm",
.owner = THIS_MODULE,
},
- .remove = __exit_p(ep93xx_pwm_remove),
+ .probe = ep93xx_pwm_probe,
+ .remove = ep93xx_pwm_remove,
};
-
-module_platform_driver_probe(ep93xx_pwm_driver, ep93xx_pwm_probe);
+module_platform_driver(ep93xx_pwm_driver);
MODULE_AUTHOR("Matthieu Crapet <mcrapet@gmail.com>, "
"H Hartley Sweeten <hsweeten@visionengravers.com>");
diff --git a/drivers/misc/hmc6352.c b/drivers/misc/hmc6352.c
index 423cd40..170bd3d 100644
--- a/drivers/misc/hmc6352.c
+++ b/drivers/misc/hmc6352.c
@@ -46,8 +46,9 @@
int ret;
unsigned long val;
- if (strict_strtoul(buf, 10, &val))
- return -EINVAL;
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
if (val >= strlen(map))
return -EINVAL;
mutex_lock(&compass_mutex);
diff --git a/drivers/misc/isl29003.c b/drivers/misc/isl29003.c
index c5145b3..e3183f2 100644
--- a/drivers/misc/isl29003.c
+++ b/drivers/misc/isl29003.c
@@ -208,7 +208,11 @@
unsigned long val;
int ret;
- if ((strict_strtoul(buf, 10, &val) < 0) || (val > 3))
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ if (val > 3)
return -EINVAL;
ret = isl29003_set_range(client, val);
@@ -239,7 +243,11 @@
unsigned long val;
int ret;
- if ((strict_strtoul(buf, 10, &val) < 0) || (val > 3))
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ if (val > 3)
return -EINVAL;
ret = isl29003_set_resolution(client, val);
@@ -267,7 +275,11 @@
unsigned long val;
int ret;
- if ((strict_strtoul(buf, 10, &val) < 0) || (val > 2))
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ if (val > 2)
return -EINVAL;
ret = isl29003_set_mode(client, val);
@@ -298,7 +310,11 @@
unsigned long val;
int ret;
- if ((strict_strtoul(buf, 10, &val) < 0) || (val > 1))
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ if (val > 1)
return -EINVAL;
ret = isl29003_set_power_state(client, val);
diff --git a/drivers/misc/isl29020.c b/drivers/misc/isl29020.c
index 0aa08c7..b7f84da 100644
--- a/drivers/misc/isl29020.c
+++ b/drivers/misc/isl29020.c
@@ -90,8 +90,10 @@
int ret_val;
unsigned long val;
- if (strict_strtoul(buf, 10, &val))
- return -EINVAL;
+ ret_val = kstrtoul(buf, 10, &val);
+ if (ret_val)
+ return ret_val;
+
if (val < 1 || val > 64000)
return -EINVAL;
diff --git a/drivers/misc/lis3lv02d/lis3lv02d.c b/drivers/misc/lis3lv02d/lis3lv02d.c
index 4cd4a3d..036effe 100644
--- a/drivers/misc/lis3lv02d/lis3lv02d.c
+++ b/drivers/misc/lis3lv02d/lis3lv02d.c
@@ -831,9 +831,11 @@
{
struct lis3lv02d *lis3 = dev_get_drvdata(dev);
unsigned long rate;
+ int ret;
- if (strict_strtoul(buf, 0, &rate))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &rate);
+ if (ret)
+ return ret;
lis3lv02d_sysfs_poweron(lis3);
if (lis3lv02d_set_odr(lis3, rate))
diff --git a/drivers/misc/mei/amthif.c b/drivers/misc/mei/amthif.c
index b3e5098..749452f 100644
--- a/drivers/misc/mei/amthif.c
+++ b/drivers/misc/mei/amthif.c
@@ -443,11 +443,11 @@
*
* returns 0, OK; otherwise, error.
*/
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list)
+int mei_amthif_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
struct mei_msg_hdr mei_hdr;
- struct mei_cl *cl = cb->cl;
size_t len = dev->iamthif_msg_buf_size - dev->iamthif_msg_buf_index;
u32 msg_slots = mei_data2slots(len);
diff --git a/drivers/misc/mei/client.c b/drivers/misc/mei/client.c
index e310ca6..c2534ca 100644
--- a/drivers/misc/mei/client.c
+++ b/drivers/misc/mei/client.c
@@ -785,6 +785,32 @@
}
+/**
+ * mei_cl_complete - processes completed operation for a client
+ *
+ * @cl: private data of the file object.
+ * @cb: callback block.
+ */
+void mei_cl_complete(struct mei_cl *cl, struct mei_cl_cb *cb)
+{
+ if (cb->fop_type == MEI_FOP_WRITE) {
+ mei_io_cb_free(cb);
+ cb = NULL;
+ cl->writing_state = MEI_WRITE_COMPLETE;
+ if (waitqueue_active(&cl->tx_wait))
+ wake_up_interruptible(&cl->tx_wait);
+
+ } else if (cb->fop_type == MEI_FOP_READ &&
+ MEI_READING == cl->reading_state) {
+ cl->reading_state = MEI_READ_COMPLETE;
+ if (waitqueue_active(&cl->rx_wait))
+ wake_up_interruptible(&cl->rx_wait);
+ else
+ mei_cl_bus_rx_event(cl);
+
+ }
+}
+
/**
* mei_cl_all_disconnect - disconnect forcefully all connected clients
diff --git a/drivers/misc/mei/client.h b/drivers/misc/mei/client.h
index cfdb144..7dc2af7 100644
--- a/drivers/misc/mei/client.h
+++ b/drivers/misc/mei/client.h
@@ -89,6 +89,7 @@
int mei_cl_connect(struct mei_cl *cl, struct file *file);
int mei_cl_read_start(struct mei_cl *cl, size_t length);
int mei_cl_write(struct mei_cl *cl, struct mei_cl_cb *cb, bool blocking);
+void mei_cl_complete(struct mei_cl *cl, struct mei_cl_cb *cb);
void mei_host_client_init(struct work_struct *work);
diff --git a/drivers/misc/mei/interrupt.c b/drivers/misc/mei/interrupt.c
index 2ad7369..7d9509a 100644
--- a/drivers/misc/mei/interrupt.c
+++ b/drivers/misc/mei/interrupt.c
@@ -31,32 +31,6 @@
/**
- * mei_cl_complete_handler - processes completed operation for a client
- *
- * @cl: private data of the file object.
- * @cb: callback block.
- */
-static void mei_cl_complete_handler(struct mei_cl *cl, struct mei_cl_cb *cb)
-{
- if (cb->fop_type == MEI_FOP_WRITE) {
- mei_io_cb_free(cb);
- cb = NULL;
- cl->writing_state = MEI_WRITE_COMPLETE;
- if (waitqueue_active(&cl->tx_wait))
- wake_up_interruptible(&cl->tx_wait);
-
- } else if (cb->fop_type == MEI_FOP_READ &&
- MEI_READING == cl->reading_state) {
- cl->reading_state = MEI_READ_COMPLETE;
- if (waitqueue_active(&cl->rx_wait))
- wake_up_interruptible(&cl->rx_wait);
- else
- mei_cl_bus_rx_event(cl);
-
- }
-}
-
-/**
* mei_irq_compl_handler - dispatch complete handelers
* for the completed callbacks
*
@@ -78,7 +52,7 @@
if (cl == &dev->iamthif_cl)
mei_amthif_complete(dev, cb);
else
- mei_cl_complete_handler(cl, cb);
+ mei_cl_complete(cl, cb);
}
}
EXPORT_SYMBOL_GPL(mei_irq_compl_handler);
@@ -189,21 +163,21 @@
}
/**
- * _mei_irq_thread_close - processes close related operation.
+ * mei_cl_irq_close - processes close related operation from
+ * interrupt thread context - send disconnect request
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_close(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_close(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots =
mei_data2slots(sizeof(struct hbm_client_connect_request));
@@ -214,15 +188,15 @@
if (mei_hbm_cl_disconnect_req(dev, cl)) {
cl->status = 0;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &cmpl_list->list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &cmpl_list->list);
return -EIO;
}
cl->state = MEI_FILE_DISCONNECTING;
cl->status = 0;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &dev->ctrl_rd_list.list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &dev->ctrl_rd_list.list);
cl->timer_count = MEI_CONNECT_TIMEOUT;
return 0;
@@ -230,26 +204,26 @@
/**
- * _mei_irq_thread_read - processes read related operation.
+ * mei_cl_irq_close - processes client read related operation from the
+ * interrupt thread context - request for flow control credits
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_read(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_read(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots = mei_data2slots(sizeof(struct hbm_flow_control));
if (*slots < msg_slots) {
/* return the cancel routine */
- list_del(&cb_pos->list);
+ list_del(&cb->list);
return -EMSGSIZE;
}
@@ -257,38 +231,38 @@
if (mei_hbm_cl_flow_control_req(dev, cl)) {
cl->status = -ENODEV;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &cmpl_list->list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &cmpl_list->list);
return -ENODEV;
}
- list_move_tail(&cb_pos->list, &dev->read_list.list);
+ list_move_tail(&cb->list, &dev->read_list.list);
return 0;
}
/**
- * _mei_irq_thread_ioctl - processes ioctl related operation.
+ * mei_cl_irq_ioctl - processes client ioctl related operation from the
+ * interrupt thread context - send connection request
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_ioctl(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_ioctl(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots =
mei_data2slots(sizeof(struct hbm_client_connect_request));
if (*slots < msg_slots) {
/* return the cancel routine */
- list_del(&cb_pos->list);
+ list_del(&cb->list);
return -EMSGSIZE;
}
@@ -298,31 +272,31 @@
if (mei_hbm_cl_connect_req(dev, cl)) {
cl->status = -ENODEV;
- cb_pos->buf_idx = 0;
- list_del(&cb_pos->list);
+ cb->buf_idx = 0;
+ list_del(&cb->list);
return -ENODEV;
- } else {
- list_move_tail(&cb_pos->list, &dev->ctrl_rd_list.list);
- cl->timer_count = MEI_CONNECT_TIMEOUT;
}
+
+ list_move_tail(&cb->list, &dev->ctrl_rd_list.list);
+ cl->timer_count = MEI_CONNECT_TIMEOUT;
return 0;
}
/**
- * mei_irq_thread_write_complete - write messages to device.
+ * mei_cl_irq_write_complete - write messages to device.
*
- * @dev: the device structure.
- * @slots: free slots.
+ * @cl: client
* @cb: callback block.
+ * @slots: free slots.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int mei_irq_thread_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
struct mei_msg_hdr mei_hdr;
- struct mei_cl *cl = cb->cl;
size_t len = cb->request_buffer.size - cb->buf_idx;
u32 msg_slots = mei_data2slots(len);
@@ -481,7 +455,7 @@
{
struct mei_cl *cl;
- struct mei_cl_cb *pos = NULL, *next = NULL;
+ struct mei_cl_cb *cb, *next;
struct mei_cl_cb *list;
s32 slots;
int ret;
@@ -498,19 +472,19 @@
dev_dbg(&dev->pdev->dev, "complete all waiting for write cb.\n");
list = &dev->write_waiting_list;
- list_for_each_entry_safe(pos, next, &list->list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &list->list, list) {
+ cl = cb->cl;
if (cl == NULL)
continue;
cl->status = 0;
- list_del(&pos->list);
+ list_del(&cb->list);
if (MEI_WRITING == cl->writing_state &&
- pos->fop_type == MEI_FOP_WRITE &&
+ cb->fop_type == MEI_FOP_WRITE &&
cl != &dev->iamthif_cl) {
dev_dbg(&dev->pdev->dev, "MEI WRITE COMPLETE\n");
cl->writing_state = MEI_WRITE_COMPLETE;
- list_add_tail(&pos->list, &cmpl_list->list);
+ list_add_tail(&cb->list, &cmpl_list->list);
}
if (cl == &dev->iamthif_cl) {
dev_dbg(&dev->pdev->dev, "check iamthif flow control.\n");
@@ -552,25 +526,23 @@
/* complete control write list CB */
dev_dbg(&dev->pdev->dev, "complete control write list cb.\n");
- list_for_each_entry_safe(pos, next, &dev->ctrl_wr_list.list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &dev->ctrl_wr_list.list, list) {
+ cl = cb->cl;
if (!cl) {
- list_del(&pos->list);
+ list_del(&cb->list);
return -ENODEV;
}
- switch (pos->fop_type) {
+ switch (cb->fop_type) {
case MEI_FOP_CLOSE:
/* send disconnect message */
- ret = _mei_irq_thread_close(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_close(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
break;
case MEI_FOP_READ:
/* send flow control message */
- ret = _mei_irq_thread_read(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_read(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
@@ -579,8 +551,7 @@
/* connect message */
if (mei_cl_is_other_connecting(cl))
continue;
- ret = _mei_irq_thread_ioctl(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_ioctl(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
@@ -593,8 +564,8 @@
}
/* complete write list CB */
dev_dbg(&dev->pdev->dev, "complete write list cb.\n");
- list_for_each_entry_safe(pos, next, &dev->write_list.list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &dev->write_list.list, list) {
+ cl = cb->cl;
if (cl == NULL)
continue;
if (mei_cl_flow_ctrl_creds(cl) <= 0) {
@@ -605,14 +576,13 @@
}
if (cl == &dev->iamthif_cl)
- ret = mei_amthif_irq_write_complete(dev, &slots,
- pos, cmpl_list);
+ ret = mei_amthif_irq_write_complete(cl, cb,
+ &slots, cmpl_list);
else
- ret = mei_irq_thread_write_complete(dev, &slots, pos,
- cmpl_list);
+ ret = mei_cl_irq_write_complete(cl, cb,
+ &slots, cmpl_list);
if (ret)
return ret;
-
}
return 0;
}
diff --git a/drivers/misc/mei/main.c b/drivers/misc/mei/main.c
index 053139f..5e11b5b 100644
--- a/drivers/misc/mei/main.c
+++ b/drivers/misc/mei/main.c
@@ -194,7 +194,6 @@
struct mei_cl_cb *cb_pos = NULL;
struct mei_cl_cb *cb = NULL;
struct mei_device *dev;
- int i;
int rets;
int err;
@@ -210,38 +209,26 @@
goto out;
}
- if ((cl->sm_state & MEI_WD_STATE_INDEPENDENCE_MSG_SENT) == 0) {
- /* Do not allow to read watchdog client */
- i = mei_me_cl_by_uuid(dev, &mei_wd_guid);
- if (i >= 0) {
- struct mei_me_client *me_client = &dev->me_clients[i];
- if (cl->me_client_id == me_client->client_id) {
- rets = -EBADF;
- goto out;
- }
- }
- } else {
- cl->sm_state &= ~MEI_WD_STATE_INDEPENDENCE_MSG_SENT;
- }
-
if (cl == &dev->iamthif_cl) {
rets = mei_amthif_read(dev, file, ubuf, length, offset);
goto out;
}
- if (cl->read_cb && cl->read_cb->buf_idx > *offset) {
+ if (cl->read_cb) {
cb = cl->read_cb;
- goto copy_buffer;
- } else if (cl->read_cb && cl->read_cb->buf_idx > 0 &&
- cl->read_cb->buf_idx <= *offset) {
- cb = cl->read_cb;
- rets = 0;
- goto free;
- } else if ((!cl->read_cb || !cl->read_cb->buf_idx) && *offset > 0) {
- /*Offset needs to be cleaned for contiguous reads*/
+ /* read what left */
+ if (cb->buf_idx > *offset)
+ goto copy_buffer;
+ /* offset is beyond buf_idx we have no more data return 0 */
+ if (cb->buf_idx > 0 && cb->buf_idx <= *offset) {
+ rets = 0;
+ goto free;
+ }
+ /* Offset needs to be cleaned for contiguous reads*/
+ if (cb->buf_idx == 0 && *offset > 0)
+ *offset = 0;
+ } else if (*offset > 0) {
*offset = 0;
- rets = 0;
- goto out;
}
err = mei_cl_read_start(cl, length);
@@ -420,16 +407,6 @@
if (rets)
goto out;
- cl->sm_state = 0;
- if (length == 4 &&
- ((memcmp(mei_wd_state_independence_msg[0],
- write_cb->request_buffer.data, 4) == 0) ||
- (memcmp(mei_wd_state_independence_msg[1],
- write_cb->request_buffer.data, 4) == 0) ||
- (memcmp(mei_wd_state_independence_msg[2],
- write_cb->request_buffer.data, 4) == 0)))
- cl->sm_state |= MEI_WD_STATE_INDEPENDENCE_MSG_SENT;
-
if (cl == &dev->iamthif_cl) {
rets = mei_amthif_write(dev, write_cb);
diff --git a/drivers/misc/mei/mei_dev.h b/drivers/misc/mei/mei_dev.h
index 4de5140..80a9031 100644
--- a/drivers/misc/mei/mei_dev.h
+++ b/drivers/misc/mei/mei_dev.h
@@ -56,11 +56,6 @@
extern const uuid_le mei_wd_guid;
/*
- * Watchdog independence state message
- */
-extern const u8 mei_wd_state_independence_msg[3][4];
-
-/*
* Number of Maximum MEI Clients
*/
#define MEI_CLIENTS_MAX 256
@@ -201,7 +196,6 @@
u8 timer_count;
enum mei_file_transaction_states reading_state;
enum mei_file_transaction_states writing_state;
- int sm_state;
struct mei_cl_cb *read_cb;
/* MEI CL bus data */
@@ -502,8 +496,8 @@
void mei_amthif_run_next_cmd(struct mei_device *dev);
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list);
+int mei_amthif_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list);
void mei_amthif_complete(struct mei_device *dev, struct mei_cl_cb *cb);
int mei_amthif_irq_read_msg(struct mei_device *dev,
@@ -522,15 +516,6 @@
*/
extern const uuid_le mei_nfc_guid;
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list);
-
-void mei_amthif_complete(struct mei_device *dev, struct mei_cl_cb *cb);
-int mei_amthif_irq_read_message(struct mei_cl_cb *complete_list,
- struct mei_device *dev, struct mei_msg_hdr *mei_hdr);
-int mei_amthif_irq_read(struct mei_device *dev, s32 *slots);
-
-
int mei_wd_send(struct mei_device *dev);
int mei_wd_stop(struct mei_device *dev);
int mei_wd_host_init(struct mei_device *dev);
diff --git a/drivers/misc/mei/pci-me.c b/drivers/misc/mei/pci-me.c
index a727464..a2f5520f 100644
--- a/drivers/misc/mei/pci-me.c
+++ b/drivers/misc/mei/pci-me.c
@@ -43,9 +43,6 @@
#include "hw-me.h"
#include "client.h"
-/* AMT device is a singleton on the platform */
-static struct pci_dev *mei_pdev;
-
/* mei_pci_tbl - PCI Device ID Table */
static DEFINE_PCI_DEVICE_TABLE(mei_me_pci_tbl) = {
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, MEI_DEV_ID_82946GZ)},
@@ -88,8 +85,6 @@
MODULE_DEVICE_TABLE(pci, mei_me_pci_tbl);
-static DEFINE_MUTEX(mei_mutex);
-
/**
* mei_quirk_probe - probe for devices that doesn't valid ME interface
*
@@ -126,17 +121,12 @@
struct mei_me_hw *hw;
int err;
- mutex_lock(&mei_mutex);
if (!mei_me_quirk_probe(pdev, ent)) {
err = -ENODEV;
goto end;
}
- if (mei_pdev) {
- err = -EEXIST;
- goto end;
- }
/* enable pci dev */
err = pci_enable_device(pdev);
if (err) {
@@ -195,13 +185,10 @@
if (err)
goto release_irq;
- mei_pdev = pdev;
pci_set_drvdata(pdev, dev);
schedule_delayed_work(&dev->timer_work, HZ);
- mutex_unlock(&mei_mutex);
-
pr_debug("initialization successful.\n");
return 0;
@@ -220,7 +207,6 @@
disable_device:
pci_disable_device(pdev);
end:
- mutex_unlock(&mei_mutex);
dev_err(&pdev->dev, "initialization failed.\n");
return err;
}
@@ -238,9 +224,6 @@
struct mei_device *dev;
struct mei_me_hw *hw;
- if (mei_pdev != pdev)
- return;
-
dev = pci_get_drvdata(pdev);
if (!dev)
return;
@@ -251,8 +234,6 @@
dev_err(&pdev->dev, "stop\n");
mei_stop(dev);
- mei_pdev = NULL;
-
/* disable interrupts */
mei_disable_interrupts(dev);
diff --git a/drivers/misc/mei/wd.c b/drivers/misc/mei/wd.c
index 6251a4e..b892143 100644
--- a/drivers/misc/mei/wd.c
+++ b/drivers/misc/mei/wd.c
@@ -31,12 +31,6 @@
static const u8 mei_start_wd_params[] = { 0x02, 0x12, 0x13, 0x10 };
static const u8 mei_stop_wd_params[] = { 0x02, 0x02, 0x14, 0x10 };
-const u8 mei_wd_state_independence_msg[3][4] = {
- {0x05, 0x02, 0x51, 0x10},
- {0x05, 0x02, 0x52, 0x10},
- {0x07, 0x02, 0x01, 0x10}
-};
-
/*
* AMT Watchdog Device
*/
diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
index 931e635..a5925f7f 100644
--- a/drivers/misc/pch_phub.c
+++ b/drivers/misc/pch_phub.c
@@ -633,17 +633,13 @@
static ssize_t store_pch_mac(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
- u8 mac[6];
+ u8 mac[ETH_ALEN];
ssize_t rom_size;
struct pch_phub_reg *chip = dev_get_drvdata(dev);
- if (count != 18)
+ if (!mac_pton(buf, mac))
return -EINVAL;
- sscanf(buf, "%02x:%02x:%02x:%02x:%02x:%02x",
- (u32 *)&mac[0], (u32 *)&mac[1], (u32 *)&mac[2], (u32 *)&mac[3],
- (u32 *)&mac[4], (u32 *)&mac[5]);
-
chip->pch_phub_extrom_base_address = pci_map_rom(chip->pdev, &rom_size);
if (!chip->pch_phub_extrom_base_address)
return -ENOMEM;
@@ -669,8 +665,6 @@
static int pch_phub_probe(struct pci_dev *pdev,
const struct pci_device_id *id)
{
- int retval;
-
int ret;
struct pch_phub_reg *chip;
@@ -713,13 +707,13 @@
if (id->driver_data == 1) { /* EG20T PCH */
const char *board_name;
- retval = sysfs_create_file(&pdev->dev.kobj,
- &dev_attr_pch_mac.attr);
- if (retval)
+ ret = sysfs_create_file(&pdev->dev.kobj,
+ &dev_attr_pch_mac.attr);
+ if (ret)
goto err_sysfs_create;
- retval = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
- if (retval)
+ ret = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
+ if (ret)
goto exit_bin_attr;
pch_phub_read_modify_write_reg(chip,
@@ -743,8 +737,8 @@
chip->pch_opt_rom_start_address = PCH_PHUB_ROM_START_ADDR_EG20T;
chip->pch_mac_start_address = PCH_PHUB_MAC_START_ADDR_EG20T;
} else if (id->driver_data == 2) { /* ML7213 IOH */
- retval = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
- if (retval)
+ ret = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
+ if (ret)
goto err_sysfs_create;
/* set the prefech value
* Device2(USB OHCI #1/ USB EHCI #1/ USB Device):a
@@ -766,12 +760,12 @@
PCH_PHUB_ROM_START_ADDR_ML7223;
chip->pch_mac_start_address = PCH_PHUB_MAC_START_ADDR_ML7223;
} else if (id->driver_data == 4) { /* ML7223 IOH Bus-n*/
- retval = sysfs_create_file(&pdev->dev.kobj,
- &dev_attr_pch_mac.attr);
- if (retval)
+ ret = sysfs_create_file(&pdev->dev.kobj,
+ &dev_attr_pch_mac.attr);
+ if (ret)
goto err_sysfs_create;
- retval = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
- if (retval)
+ ret = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
+ if (ret)
goto exit_bin_attr;
/* set the prefech value
* Device2(USB OHCI #0,1,2,3/ USB EHCI #0):a
@@ -783,13 +777,13 @@
PCH_PHUB_ROM_START_ADDR_ML7223;
chip->pch_mac_start_address = PCH_PHUB_MAC_START_ADDR_ML7223;
} else if (id->driver_data == 5) { /* ML7831 */
- retval = sysfs_create_file(&pdev->dev.kobj,
- &dev_attr_pch_mac.attr);
- if (retval)
+ ret = sysfs_create_file(&pdev->dev.kobj,
+ &dev_attr_pch_mac.attr);
+ if (ret)
goto err_sysfs_create;
- retval = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
- if (retval)
+ ret = sysfs_create_bin_file(&pdev->dev.kobj, &pch_bin_attr);
+ if (ret)
goto exit_bin_attr;
/* set the prefech value */
diff --git a/drivers/misc/sgi-gru/gruprocfs.c b/drivers/misc/sgi-gru/gruprocfs.c
index 797d796..4f76359 100644
--- a/drivers/misc/sgi-gru/gruprocfs.c
+++ b/drivers/misc/sgi-gru/gruprocfs.c
@@ -160,15 +160,11 @@
static ssize_t options_write(struct file *file, const char __user *userbuf,
size_t count, loff_t *data)
{
- char buf[20];
+ int ret;
- if (count >= sizeof(buf))
- return -EINVAL;
- if (copy_from_user(buf, userbuf, count))
- return -EFAULT;
- buf[count] = '\0';
- if (strict_strtoul(buf, 0, &gru_options))
- return -EINVAL;
+ ret = kstrtoul_from_user(userbuf, count, 0, &gru_options);
+ if (ret)
+ return ret;
return count;
}
diff --git a/drivers/misc/spear13xx_pcie_gadget.c b/drivers/misc/spear13xx_pcie_gadget.c
index 7deb25d..2e13614 100644
--- a/drivers/misc/spear13xx_pcie_gadget.c
+++ b/drivers/misc/spear13xx_pcie_gadget.c
@@ -316,8 +316,12 @@
struct spear_pcie_gadget_config *config,
const char *buf, size_t count)
{
- if (strict_strtoul(buf, 0, &config->requested_msi))
- return -EINVAL;
+ int ret;
+
+ ret = kstrtoul(buf, 0, &config->requested_msi);
+ if (ret)
+ return ret;
+
if (config->requested_msi > 32)
config->requested_msi = 32;
@@ -330,9 +334,11 @@
{
struct pcie_app_reg __iomem *app_reg = config->va_app_base;
ulong en;
+ int ret;
- if (strict_strtoul(buf, 0, &en))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &en);
+ if (ret)
+ return ret;
if (en)
writel(readl(&app_reg->app_ctrl_0) | (1 << SYS_INT_ID),
@@ -351,9 +357,11 @@
struct pcie_app_reg __iomem *app_reg = config->va_app_base;
ulong vector;
u32 ven_msi;
+ int ret;
- if (strict_strtoul(buf, 0, &vector))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &vector);
+ if (ret)
+ return ret;
if (!config->configured_msi)
return -EINVAL;
@@ -395,9 +403,11 @@
const char *buf, size_t count)
{
ulong id;
+ int ret;
- if (strict_strtoul(buf, 0, &id))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &id);
+ if (ret)
+ return ret;
spear_dbi_write_reg(config, PCI_VENDOR_ID, 2, id);
@@ -420,9 +430,11 @@
const char *buf, size_t count)
{
ulong id;
+ int ret;
- if (strict_strtoul(buf, 0, &id))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &id);
+ if (ret)
+ return ret;
spear_dbi_write_reg(config, PCI_DEVICE_ID, 2, id);
@@ -443,9 +455,12 @@
ulong size;
u32 pos, pos1;
u32 no_of_bit = 0;
+ int ret;
- if (strict_strtoul(buf, 0, &size))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &size);
+ if (ret)
+ return ret;
+
/* min bar size is 256 */
if (size <= 0x100)
size = 0x100;
@@ -490,9 +505,11 @@
{
struct pcie_app_reg __iomem *app_reg = config->va_app_base;
ulong address;
+ int ret;
- if (strict_strtoul(buf, 0, &address))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &address);
+ if (ret)
+ return ret;
address &= ~(config->bar0_size - 1);
if (config->va_bar0_address)
@@ -518,9 +535,11 @@
const char *buf, size_t count)
{
ulong offset;
+ int ret;
- if (strict_strtoul(buf, 0, &offset))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &offset);
+ if (ret)
+ return ret;
if (offset % 4)
return -EINVAL;
@@ -549,9 +568,11 @@
const char *buf, size_t count)
{
ulong data;
+ int ret;
- if (strict_strtoul(buf, 0, &data))
- return -EINVAL;
+ ret = kstrtoul(buf, 0, &data);
+ if (ret)
+ return ret;
if (!config->va_bar0_address)
return -ENOMEM;
@@ -776,7 +797,7 @@
goto err_iounmap_app;
}
- dev_set_drvdata(&pdev->dev, target);
+ platform_set_drvdata(pdev, target);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
@@ -814,9 +835,11 @@
clk = clk_get_sys("pcie1", NULL);
if (IS_ERR(clk)) {
pr_err("%s:couldn't get clk for pcie1\n", __func__);
+ status = PTR_ERR(clk);
goto err_irq;
}
- if (clk_enable(clk)) {
+ status = clk_enable(clk);
+ if (status) {
pr_err("%s:couldn't enable clk for pcie1\n", __func__);
goto err_irq;
}
@@ -828,9 +851,11 @@
clk = clk_get_sys("pcie2", NULL);
if (IS_ERR(clk)) {
pr_err("%s:couldn't get clk for pcie2\n", __func__);
+ status = PTR_ERR(clk);
goto err_irq;
}
- if (clk_enable(clk)) {
+ status = clk_enable(clk);
+ if (status) {
pr_err("%s:couldn't enable clk for pcie2\n", __func__);
goto err_irq;
}
@@ -863,7 +888,7 @@
res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
irq = platform_get_irq(pdev, 0);
- target = dev_get_drvdata(&pdev->dev);
+ target = platform_get_drvdata(pdev);
config = &target->config;
free_irq(irq, NULL);
diff --git a/drivers/misc/sram.c b/drivers/misc/sram.c
index 437192e..4a93886 100644
--- a/drivers/misc/sram.c
+++ b/drivers/misc/sram.c
@@ -50,9 +50,10 @@
size = resource_size(res);
- virt_base = devm_request_and_ioremap(&pdev->dev, res);
- if (!virt_base)
- return -EADDRNOTAVAIL;
+ virt_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(virt_base))
+ return PTR_ERR(virt_base);
+
sram = devm_kzalloc(&pdev->dev, sizeof(*sram), GFP_KERNEL);
if (!sram)
diff --git a/drivers/misc/ti-st/st_kim.c b/drivers/misc/ti-st/st_kim.c
index 83269f1..83907c7 100644
--- a/drivers/misc/ti-st/st_kim.c
+++ b/drivers/misc/ti-st/st_kim.c
@@ -680,7 +680,7 @@
*core_data = NULL;
return;
}
- kim_gdata = dev_get_drvdata(&pdev->dev);
+ kim_gdata = platform_get_drvdata(pdev);
*core_data = kim_gdata->core_data;
}
@@ -735,7 +735,7 @@
pr_err("no mem to allocate");
return -ENOMEM;
}
- dev_set_drvdata(&pdev->dev, kim_gdata);
+ platform_set_drvdata(pdev, kim_gdata);
err = st_core_init(&kim_gdata->core_data);
if (err != 0) {
@@ -810,7 +810,7 @@
struct ti_st_plat_data *pdata = pdev->dev.platform_data;
struct kim_data_s *kim_gdata;
- kim_gdata = dev_get_drvdata(&pdev->dev);
+ kim_gdata = platform_get_drvdata(pdev);
/* Free the Bluetooth/FM/GPIO
* nShutdown gpio from the system
diff --git a/drivers/misc/ti_dac7512.c b/drivers/misc/ti_dac7512.c
index 1d86407..9b23722 100644
--- a/drivers/misc/ti_dac7512.c
+++ b/drivers/misc/ti_dac7512.c
@@ -33,9 +33,11 @@
struct spi_device *spi = to_spi_device(dev);
unsigned char tmp[2];
unsigned long val;
+ int ret;
- if (strict_strtoul(buf, 10, &val) < 0)
- return -EINVAL;
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
tmp[0] = val >> 8;
tmp[1] = val & 0xff;
diff --git a/drivers/misc/tsl2550.c b/drivers/misc/tsl2550.c
index 1dfde4d..5bc10fa1 100644
--- a/drivers/misc/tsl2550.c
+++ b/drivers/misc/tsl2550.c
@@ -204,7 +204,7 @@
unsigned long val = simple_strtoul(buf, NULL, 10);
int ret;
- if (val < 0 || val > 1)
+ if (val > 1)
return -EINVAL;
mutex_lock(&data->update_lock);
@@ -236,7 +236,7 @@
unsigned long val = simple_strtoul(buf, NULL, 10);
int ret;
- if (val < 0 || val > 1)
+ if (val > 1)
return -EINVAL;
if (data->power_state == 0)
diff --git a/drivers/net/netconsole.c b/drivers/net/netconsole.c
index 59ac143..4f777ed9 100644
--- a/drivers/net/netconsole.c
+++ b/drivers/net/netconsole.c
@@ -40,6 +40,7 @@
#include <linux/slab.h>
#include <linux/console.h>
#include <linux/moduleparam.h>
+#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/netpoll.h>
#include <linux/inet.h>
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index b90f85b..80faa56 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -288,7 +288,7 @@
config AT91_CF
tristate "AT91 CompactFlash Controller"
- depends on PCMCIA && ARCH_AT91RM9200
+ depends on PCMCIA && ARCH_AT91
help
Say Y here to support the CompactFlash controller on AT91 chips.
Or choose M to compile the driver as a module named "at91_cf".
diff --git a/drivers/pcmcia/at91_cf.c b/drivers/pcmcia/at91_cf.c
index 01463c7..b8f5acf 100644
--- a/drivers/pcmcia/at91_cf.c
+++ b/drivers/pcmcia/at91_cf.c
@@ -18,13 +18,14 @@
#include <linux/slab.h>
#include <linux/gpio.h>
#include <linux/platform_data/atmel.h>
+#include <linux/io.h>
+#include <linux/sizes.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <pcmcia/ss.h>
-#include <mach/hardware.h>
-#include <asm/io.h>
-#include <asm/sizes.h>
-
#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
@@ -41,8 +42,6 @@
/*--------------------------------------------------------------------------*/
-static const char driver_name[] = "at91_cf";
-
struct at91_cf_socket {
struct pcmcia_socket socket;
@@ -76,7 +75,7 @@
/* kick pccard as needed */
if (present != cf->present) {
cf->present = present;
- pr_debug("%s: card %s\n", driver_name,
+ dev_dbg(&cf->pdev->dev, "card %s\n",
present ? "present" : "gone");
pcmcia_parse_events(&cf->socket, SS_DETECT);
}
@@ -100,9 +99,9 @@
int vcc = gpio_is_valid(cf->board->vcc_pin);
*sp = SS_DETECT | SS_3VCARD;
- if (!rdy || gpio_get_value(rdy))
+ if (!rdy || gpio_get_value(cf->board->irq_pin))
*sp |= SS_READY;
- if (!vcc || gpio_get_value(vcc))
+ if (!vcc || gpio_get_value(cf->board->vcc_pin))
*sp |= SS_POWERON;
} else
*sp = 0;
@@ -120,22 +119,22 @@
/* switch Vcc if needed and possible */
if (gpio_is_valid(cf->board->vcc_pin)) {
switch (s->Vcc) {
- case 0:
- gpio_set_value(cf->board->vcc_pin, 0);
- break;
- case 33:
- gpio_set_value(cf->board->vcc_pin, 1);
- break;
- default:
- return -EINVAL;
+ case 0:
+ gpio_set_value(cf->board->vcc_pin, 0);
+ break;
+ case 33:
+ gpio_set_value(cf->board->vcc_pin, 1);
+ break;
+ default:
+ return -EINVAL;
}
}
/* toggle reset if needed */
gpio_set_value(cf->board->rst_pin, s->flags & SS_RESET);
- pr_debug("%s: Vcc %d, io_irq %d, flags %04x csc %04x\n",
- driver_name, s->Vcc, s->io_irq, s->flags, s->csc_mask);
+ dev_dbg(&cf->pdev->dev, "Vcc %d, io_irq %d, flags %04x csc %04x\n",
+ s->Vcc, s->io_irq, s->flags, s->csc_mask);
return 0;
}
@@ -171,10 +170,10 @@
*/
if (!(io->flags & (MAP_16BIT | MAP_AUTOSZ))) {
csr |= AT91_SMC_DBW_8;
- pr_debug("%s: 8bit i/o bus\n", driver_name);
+ dev_dbg(&cf->pdev->dev, "8bit i/o bus\n");
} else {
csr |= AT91_SMC_DBW_16;
- pr_debug("%s: 16bit i/o bus\n", driver_name);
+ dev_dbg(&cf->pdev->dev, "16bit i/o bus\n");
}
at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
@@ -215,6 +214,37 @@
/*--------------------------------------------------------------------------*/
+#if defined(CONFIG_OF)
+static const struct of_device_id at91_cf_dt_ids[] = {
+ { .compatible = "atmel,at91rm9200-cf" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, at91_cf_dt_ids);
+
+static int at91_cf_dt_init(struct platform_device *pdev)
+{
+ struct at91_cf_data *board;
+
+ board = devm_kzalloc(&pdev->dev, sizeof(*board), GFP_KERNEL);
+ if (!board)
+ return -ENOMEM;
+
+ board->irq_pin = of_get_gpio(pdev->dev.of_node, 0);
+ board->det_pin = of_get_gpio(pdev->dev.of_node, 1);
+ board->vcc_pin = of_get_gpio(pdev->dev.of_node, 2);
+ board->rst_pin = of_get_gpio(pdev->dev.of_node, 3);
+
+ pdev->dev.platform_data = board;
+
+ return 0;
+}
+#else
+static int at91_cf_dt_init(struct platform_device *pdev)
+{
+ return -ENODEV;
+}
+#endif
+
static int __init at91_cf_probe(struct platform_device *pdev)
{
struct at91_cf_socket *cf;
@@ -222,14 +252,22 @@
struct resource *io;
int status;
- if (!board || !gpio_is_valid(board->det_pin) || !gpio_is_valid(board->rst_pin))
+ if (!board) {
+ status = at91_cf_dt_init(pdev);
+ if (status)
+ return status;
+
+ board = pdev->dev.platform_data;
+ }
+
+ if (!gpio_is_valid(board->det_pin) || !gpio_is_valid(board->rst_pin))
return -ENODEV;
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!io)
return -ENODEV;
- cf = kzalloc(sizeof *cf, GFP_KERNEL);
+ cf = devm_kzalloc(&pdev->dev, sizeof(*cf), GFP_KERNEL);
if (!cf)
return -ENOMEM;
@@ -239,22 +277,25 @@
platform_set_drvdata(pdev, cf);
/* must be a GPIO; ergo must trigger on both edges */
- status = gpio_request(board->det_pin, "cf_det");
+ status = devm_gpio_request(&pdev->dev, board->det_pin, "cf_det");
if (status < 0)
- goto fail0;
- status = request_irq(gpio_to_irq(board->det_pin), at91_cf_irq, 0, driver_name, cf);
+ return status;
+
+ status = devm_request_irq(&pdev->dev, gpio_to_irq(board->det_pin),
+ at91_cf_irq, 0, "at91_cf detect", cf);
if (status < 0)
- goto fail00;
+ return status;
+
device_init_wakeup(&pdev->dev, 1);
- status = gpio_request(board->rst_pin, "cf_rst");
+ status = devm_gpio_request(&pdev->dev, board->rst_pin, "cf_rst");
if (status < 0)
goto fail0a;
if (gpio_is_valid(board->vcc_pin)) {
- status = gpio_request(board->vcc_pin, "cf_vcc");
+ status = devm_gpio_request(&pdev->dev, board->vcc_pin, "cf_vcc");
if (status < 0)
- goto fail0b;
+ goto fail0a;
}
/*
@@ -264,32 +305,33 @@
* (Note: DK board doesn't wire the IRQ pin...)
*/
if (gpio_is_valid(board->irq_pin)) {
- status = gpio_request(board->irq_pin, "cf_irq");
+ status = devm_gpio_request(&pdev->dev, board->irq_pin, "cf_irq");
if (status < 0)
- goto fail0c;
- status = request_irq(gpio_to_irq(board->irq_pin), at91_cf_irq,
- IRQF_SHARED, driver_name, cf);
+ goto fail0a;
+
+ status = devm_request_irq(&pdev->dev, gpio_to_irq(board->irq_pin),
+ at91_cf_irq, IRQF_SHARED, "at91_cf", cf);
if (status < 0)
- goto fail0d;
+ goto fail0a;
cf->socket.pci_irq = gpio_to_irq(board->irq_pin);
} else
cf->socket.pci_irq = nr_irqs + 1;
/* pcmcia layer only remaps "real" memory not iospace */
- cf->socket.io_offset = (unsigned long)
- ioremap(cf->phys_baseaddr + CF_IO_PHYS, SZ_2K);
+ cf->socket.io_offset = (unsigned long) devm_ioremap(&pdev->dev,
+ cf->phys_baseaddr + CF_IO_PHYS, SZ_2K);
if (!cf->socket.io_offset) {
status = -ENXIO;
- goto fail1;
+ goto fail0a;
}
/* reserve chip-select regions */
- if (!request_mem_region(io->start, resource_size(io), driver_name)) {
+ if (!devm_request_mem_region(&pdev->dev, io->start, resource_size(io), "at91_cf")) {
status = -ENXIO;
- goto fail1;
+ goto fail0a;
}
- pr_info("%s: irqs det #%d, io #%d\n", driver_name,
+ dev_info(&pdev->dev, "irqs det #%d, io #%d\n",
gpio_to_irq(board->det_pin), gpio_to_irq(board->irq_pin));
cf->socket.owner = THIS_MODULE;
@@ -303,55 +345,22 @@
status = pcmcia_register_socket(&cf->socket);
if (status < 0)
- goto fail2;
+ goto fail0a;
return 0;
-fail2:
- release_mem_region(io->start, resource_size(io));
-fail1:
- if (cf->socket.io_offset)
- iounmap((void __iomem *) cf->socket.io_offset);
- if (gpio_is_valid(board->irq_pin)) {
- free_irq(gpio_to_irq(board->irq_pin), cf);
-fail0d:
- gpio_free(board->irq_pin);
- }
-fail0c:
- if (gpio_is_valid(board->vcc_pin))
- gpio_free(board->vcc_pin);
-fail0b:
- gpio_free(board->rst_pin);
fail0a:
device_init_wakeup(&pdev->dev, 0);
- free_irq(gpio_to_irq(board->det_pin), cf);
-fail00:
- gpio_free(board->det_pin);
-fail0:
- kfree(cf);
return status;
}
static int __exit at91_cf_remove(struct platform_device *pdev)
{
struct at91_cf_socket *cf = platform_get_drvdata(pdev);
- struct at91_cf_data *board = cf->board;
- struct resource *io = cf->socket.io[0].res;
pcmcia_unregister_socket(&cf->socket);
- release_mem_region(io->start, resource_size(io));
- iounmap((void __iomem *) cf->socket.io_offset);
- if (gpio_is_valid(board->irq_pin)) {
- free_irq(gpio_to_irq(board->irq_pin), cf);
- gpio_free(board->irq_pin);
- }
- if (gpio_is_valid(board->vcc_pin))
- gpio_free(board->vcc_pin);
- gpio_free(board->rst_pin);
device_init_wakeup(&pdev->dev, 0);
- free_irq(gpio_to_irq(board->det_pin), cf);
- gpio_free(board->det_pin);
- kfree(cf);
+
return 0;
}
@@ -391,8 +400,9 @@
static struct platform_driver at91_cf_driver = {
.driver = {
- .name = (char *) driver_name,
+ .name = "at91_cf",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(at91_cf_dt_ids),
},
.remove = __exit_p(at91_cf_remove),
.suspend = at91_cf_suspend,
@@ -401,17 +411,7 @@
/*--------------------------------------------------------------------------*/
-static int __init at91_cf_init(void)
-{
- return platform_driver_probe(&at91_cf_driver, at91_cf_probe);
-}
-module_init(at91_cf_init);
-
-static void __exit at91_cf_exit(void)
-{
- platform_driver_unregister(&at91_cf_driver);
-}
-module_exit(at91_cf_exit);
+module_platform_driver_probe(at91_cf_driver, at91_cf_probe);
MODULE_DESCRIPTION("AT91 Compact Flash Driver");
MODULE_AUTHOR("David Brownell");
diff --git a/drivers/uio/uio_aec.c b/drivers/uio/uio_aec.c
index 1548982..f3611c2 100644
--- a/drivers/uio/uio_aec.c
+++ b/drivers/uio/uio_aec.c
@@ -160,17 +160,5 @@
.remove = remove,
};
-static int __init aectc_init(void)
-{
- return pci_register_driver(&pci_driver);
-}
-
-static void __exit aectc_exit(void)
-{
- pci_unregister_driver(&pci_driver);
-}
-
+module_pci_driver(pci_driver);
MODULE_LICENSE("GPL");
-
-module_init(aectc_init);
-module_exit(aectc_exit);
diff --git a/drivers/uio/uio_cif.c b/drivers/uio/uio_cif.c
index 7dd6fc6..22cdf38 100644
--- a/drivers/uio/uio_cif.c
+++ b/drivers/uio/uio_cif.c
@@ -135,19 +135,7 @@
.remove = hilscher_pci_remove,
};
-static int __init hilscher_init_module(void)
-{
- return pci_register_driver(&hilscher_pci_driver);
-}
-
-static void __exit hilscher_exit_module(void)
-{
- pci_unregister_driver(&hilscher_pci_driver);
-}
-
-module_init(hilscher_init_module);
-module_exit(hilscher_exit_module);
-
+module_pci_driver(hilscher_pci_driver);
MODULE_DEVICE_TABLE(pci, hilscher_pci_ids);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Hans J. Koch, Benedikt Spranger");
diff --git a/drivers/uio/uio_netx.c b/drivers/uio/uio_netx.c
index 6a4ba5e..28a766b 100644
--- a/drivers/uio/uio_netx.c
+++ b/drivers/uio/uio_netx.c
@@ -174,19 +174,7 @@
.remove = netx_pci_remove,
};
-static int __init netx_init_module(void)
-{
- return pci_register_driver(&netx_pci_driver);
-}
-
-static void __exit netx_exit_module(void)
-{
- pci_unregister_driver(&netx_pci_driver);
-}
-
-module_init(netx_init_module);
-module_exit(netx_exit_module);
-
+module_pci_driver(netx_pci_driver);
MODULE_DEVICE_TABLE(pci, netx_pci_ids);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Hans J. Koch, Manuel Traut");
diff --git a/drivers/uio/uio_pci_generic.c b/drivers/uio/uio_pci_generic.c
index 14aa10c..077ae12 100644
--- a/drivers/uio/uio_pci_generic.c
+++ b/drivers/uio/uio_pci_generic.c
@@ -113,27 +113,14 @@
kfree(gdev);
}
-static struct pci_driver driver = {
+static struct pci_driver uio_pci_driver = {
.name = "uio_pci_generic",
.id_table = NULL, /* only dynamic id's */
.probe = probe,
.remove = remove,
};
-static int __init init(void)
-{
- pr_info(DRIVER_DESC " version: " DRIVER_VERSION "\n");
- return pci_register_driver(&driver);
-}
-
-static void __exit cleanup(void)
-{
- pci_unregister_driver(&driver);
-}
-
-module_init(init);
-module_exit(cleanup);
-
+module_pci_driver(uio_pci_driver);
MODULE_VERSION(DRIVER_VERSION);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR(DRIVER_AUTHOR);
diff --git a/drivers/uio/uio_pruss.c b/drivers/uio/uio_pruss.c
index 6e2ab00..21f7a72 100644
--- a/drivers/uio/uio_pruss.c
+++ b/drivers/uio/uio_pruss.c
@@ -136,9 +136,9 @@
gdev->pruss_clk = clk_get(&dev->dev, "pruss");
if (IS_ERR(gdev->pruss_clk)) {
dev_err(&dev->dev, "Failed to get clock\n");
+ ret = PTR_ERR(gdev->pruss_clk);
kfree(gdev->info);
kfree(gdev);
- ret = PTR_ERR(gdev->pruss_clk);
return ret;
} else {
clk_enable(gdev->pruss_clk);
diff --git a/drivers/uio/uio_sercos3.c b/drivers/uio/uio_sercos3.c
index 81a10a5..5419832 100644
--- a/drivers/uio/uio_sercos3.c
+++ b/drivers/uio/uio_sercos3.c
@@ -226,19 +226,7 @@
.remove = sercos3_pci_remove,
};
-static int __init sercos3_init_module(void)
-{
- return pci_register_driver(&sercos3_pci_driver);
-}
-
-static void __exit sercos3_exit_module(void)
-{
- pci_unregister_driver(&sercos3_pci_driver);
-}
-
-module_init(sercos3_init_module);
-module_exit(sercos3_exit_module);
-
+module_pci_driver(sercos3_pci_driver);
MODULE_DESCRIPTION("UIO driver for the Automata Sercos III PCI card");
MODULE_AUTHOR("John Ogness <john.ogness@linutronix.de>");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/vme/vme.c b/drivers/vme/vme.c
index 5e6c7d7..f6856b4 100644
--- a/drivers/vme/vme.c
+++ b/drivers/vme/vme.c
@@ -959,6 +959,8 @@
mutex_unlock(&ctrlr->mtx);
+ kfree(resource);
+
return 0;
}
EXPORT_SYMBOL(vme_dma_free);
diff --git a/drivers/w1/masters/w1-gpio.c b/drivers/w1/masters/w1-gpio.c
index 46d9701..f54ece2 100644
--- a/drivers/w1/masters/w1-gpio.c
+++ b/drivers/w1/masters/w1-gpio.c
@@ -16,7 +16,6 @@
#include <linux/gpio.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
-#include <linux/pinctrl/consumer.h>
#include <linux/err.h>
#include <linux/of.h>
@@ -78,13 +77,8 @@
{
struct w1_bus_master *master;
struct w1_gpio_platform_data *pdata;
- struct pinctrl *pinctrl;
int err;
- pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
- if (IS_ERR(pinctrl))
- dev_warn(&pdev->dev, "unable to select pin group\n");
-
if (of_have_populated_dt()) {
err = w1_gpio_probe_dt(pdev);
if (err < 0) {
diff --git a/drivers/w1/slaves/w1_ds2408.c b/drivers/w1/slaves/w1_ds2408.c
index e45eca1..91cc2cd 100644
--- a/drivers/w1/slaves/w1_ds2408.c
+++ b/drivers/w1/slaves/w1_ds2408.c
@@ -22,6 +22,7 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Jean-Francois Dagenais <dagenaisj@sonatest.com>");
MODULE_DESCRIPTION("w1 family 29 driver for DS2408 8 Pin IO");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2408));
#define W1_F29_RETRIES 3
diff --git a/drivers/w1/slaves/w1_ds2413.c b/drivers/w1/slaves/w1_ds2413.c
index 8297862..8593777 100644
--- a/drivers/w1/slaves/w1_ds2413.c
+++ b/drivers/w1/slaves/w1_ds2413.c
@@ -23,6 +23,7 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Mariusz Bialonczyk <manio@skyboo.net>");
MODULE_DESCRIPTION("w1 family 3a driver for DS2413 2 Pin IO");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2413));
#define W1_F3A_RETRIES 3
#define W1_F3A_FUNC_PIO_ACCESS_READ 0xF5
diff --git a/drivers/w1/slaves/w1_ds2423.c b/drivers/w1/slaves/w1_ds2423.c
index 40a10b5..7f86aec 100644
--- a/drivers/w1/slaves/w1_ds2423.c
+++ b/drivers/w1/slaves/w1_ds2423.c
@@ -164,3 +164,4 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Mika Laitio <lamikr@pilppa.org>");
MODULE_DESCRIPTION("w1 family 1d driver for DS2423, 4 counters and 4kb ram");
+MODULE_ALIAS("w1-family-" __stringify(W1_COUNTER_DS2423));
diff --git a/drivers/w1/slaves/w1_ds2431.c b/drivers/w1/slaves/w1_ds2431.c
index 984b303..cef8605 100644
--- a/drivers/w1/slaves/w1_ds2431.c
+++ b/drivers/w1/slaves/w1_ds2431.c
@@ -310,3 +310,4 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Bernhard Weirich <bernhard.weirich@riedel.net>");
MODULE_DESCRIPTION("w1 family 2d driver for DS2431, 1kb EEPROM");
+MODULE_ALIAS("w1-family-" __stringify(W1_EEPROM_DS2431));
diff --git a/drivers/w1/slaves/w1_ds2433.c b/drivers/w1/slaves/w1_ds2433.c
index 85f2cdb..10cc1b6 100644
--- a/drivers/w1/slaves/w1_ds2433.c
+++ b/drivers/w1/slaves/w1_ds2433.c
@@ -29,6 +29,7 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
MODULE_DESCRIPTION("w1 family 23 driver for DS2433, 4kb EEPROM");
+MODULE_ALIAS("w1-family-" __stringify(W1_EEPROM_DS2433));
#define W1_EEPROM_SIZE 512
#define W1_PAGE_COUNT 16
diff --git a/drivers/w1/slaves/w1_ds2760.c b/drivers/w1/slaves/w1_ds2760.c
index e86a69d..93719d25 100644
--- a/drivers/w1/slaves/w1_ds2760.c
+++ b/drivers/w1/slaves/w1_ds2760.c
@@ -203,3 +203,4 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>");
MODULE_DESCRIPTION("1-wire Driver Dallas 2760 battery monitor chip");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2760));
diff --git a/drivers/w1/slaves/w1_ds2780.c b/drivers/w1/slaves/w1_ds2780.c
index 98ed9c4..0cd7a27 100644
--- a/drivers/w1/slaves/w1_ds2780.c
+++ b/drivers/w1/slaves/w1_ds2780.c
@@ -188,3 +188,4 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Clifton Barnes <cabarnes@indesign-llc.com>");
MODULE_DESCRIPTION("1-wire Driver for Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2780));
diff --git a/drivers/w1/slaves/w1_ds2781.c b/drivers/w1/slaves/w1_ds2781.c
index 5140d7b..1aba8e4 100644
--- a/drivers/w1/slaves/w1_ds2781.c
+++ b/drivers/w1/slaves/w1_ds2781.c
@@ -186,3 +186,4 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Renata Sayakhova <renata@oktetlabs.ru>");
MODULE_DESCRIPTION("1-wire Driver for Maxim/Dallas DS2781 Stand-Alone Fuel Gauge IC");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2781));
diff --git a/drivers/w1/slaves/w1_ds28e04.c b/drivers/w1/slaves/w1_ds28e04.c
index 98117db..cd30a6d 100644
--- a/drivers/w1/slaves/w1_ds28e04.c
+++ b/drivers/w1/slaves/w1_ds28e04.c
@@ -27,6 +27,7 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Markus Franke <franke.m@sebakmt.com>, <franm@hrz.tu-chemnitz.de>");
MODULE_DESCRIPTION("w1 family 1C driver for DS28E04, 4kb EEPROM and PIO");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS28E04));
/* Allow the strong pullup to be disabled, but default to enabled.
* If it was disabled a parasite powered device might not get the required
diff --git a/drivers/w1/slaves/w1_smem.c b/drivers/w1/slaves/w1_smem.c
index 8465562..ed4c875 100644
--- a/drivers/w1/slaves/w1_smem.c
+++ b/drivers/w1/slaves/w1_smem.c
@@ -34,6 +34,8 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Evgeniy Polyakov <zbr@ioremap.net>");
MODULE_DESCRIPTION("Driver for 1-wire Dallas network protocol, 64bit memory family.");
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_SMEM_01));
+MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_SMEM_81));
static struct w1_family w1_smem_family_01 = {
.fid = W1_FAMILY_SMEM_01,
diff --git a/drivers/w1/slaves/w1_therm.c b/drivers/w1/slaves/w1_therm.c
index c1a702f..8978360 100644
--- a/drivers/w1/slaves/w1_therm.c
+++ b/drivers/w1/slaves/w1_therm.c
@@ -36,6 +36,11 @@
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Evgeniy Polyakov <zbr@ioremap.net>");
MODULE_DESCRIPTION("Driver for 1-wire Dallas network protocol, temperature family.");
+MODULE_ALIAS("w1-family-" __stringify(W1_THERM_DS18S20));
+MODULE_ALIAS("w1-family-" __stringify(W1_THERM_DS1822));
+MODULE_ALIAS("w1-family-" __stringify(W1_THERM_DS18B20));
+MODULE_ALIAS("w1-family-" __stringify(W1_THERM_DS1825));
+MODULE_ALIAS("w1-family-" __stringify(W1_THERM_DS28EA00));
/* Allow the strong pullup to be disabled, but default to enabled.
* If it was disabled a parasite powered device might not get the require
diff --git a/drivers/w1/w1.c b/drivers/w1/w1.c
index 7ce277d..0459df8 100644
--- a/drivers/w1/w1.c
+++ b/drivers/w1/w1.c
@@ -680,6 +680,8 @@
atomic_set(&sl->refcnt, 0);
init_completion(&sl->released);
+ request_module("w1-family-0x%0x", rn->family);
+
spin_lock(&w1_flock);
f = w1_family_registered(rn->family);
if (!f) {
diff --git a/include/linux/hyperv.h b/include/linux/hyperv.h
index c255984..fae8bac 100644
--- a/include/linux/hyperv.h
+++ b/include/linux/hyperv.h
@@ -909,6 +909,7 @@
CHANNEL_OFFER_STATE,
CHANNEL_OPENING_STATE,
CHANNEL_OPEN_STATE,
+ CHANNEL_OPENED_STATE,
};
struct vmbus_channel_debug_info {
@@ -1046,6 +1047,38 @@
* preserve the earlier behavior.
*/
u32 target_vp;
+ /*
+ * Support for sub-channels. For high performance devices,
+ * it will be useful to have multiple sub-channels to support
+ * a scalable communication infrastructure with the host.
+ * The support for sub-channels is implemented as an extention
+ * to the current infrastructure.
+ * The initial offer is considered the primary channel and this
+ * offer message will indicate if the host supports sub-channels.
+ * The guest is free to ask for sub-channels to be offerred and can
+ * open these sub-channels as a normal "primary" channel. However,
+ * all sub-channels will have the same type and instance guids as the
+ * primary channel. Requests sent on a given channel will result in a
+ * response on the same channel.
+ */
+
+ /*
+ * Sub-channel creation callback. This callback will be called in
+ * process context when a sub-channel offer is received from the host.
+ * The guest can open the sub-channel in the context of this callback.
+ */
+ void (*sc_creation_callback)(struct vmbus_channel *new_sc);
+
+ spinlock_t sc_lock;
+ /*
+ * All Sub-channels of a primary channel are linked here.
+ */
+ struct list_head sc_list;
+ /*
+ * The primary channel this sub-channel belongs to.
+ * This will be NULL for the primary channel.
+ */
+ struct vmbus_channel *primary_channel;
};
static inline void set_channel_read_state(struct vmbus_channel *c, bool state)
@@ -1057,6 +1090,34 @@
int vmbus_request_offers(void);
+/*
+ * APIs for managing sub-channels.
+ */
+
+void vmbus_set_sc_create_callback(struct vmbus_channel *primary_channel,
+ void (*sc_cr_cb)(struct vmbus_channel *new_sc));
+
+/*
+ * Retrieve the (sub) channel on which to send an outgoing request.
+ * When a primary channel has multiple sub-channels, we choose a
+ * channel whose VCPU binding is closest to the VCPU on which
+ * this call is being made.
+ */
+struct vmbus_channel *vmbus_get_outgoing_channel(struct vmbus_channel *primary);
+
+/*
+ * Check if sub-channels have already been offerred. This API will be useful
+ * when the driver is unloaded after establishing sub-channels. In this case,
+ * when the driver is re-loaded, the driver would have to check if the
+ * subchannels have already been established before attempting to request
+ * the creation of sub-channels.
+ * This function returns TRUE to indicate that subchannels have already been
+ * created.
+ * This function should be invoked after setting the callback function for
+ * sub-channel creation.
+ */
+bool vmbus_are_subchannels_present(struct vmbus_channel *primary);
+
/* The format must be the same as struct vmdata_gpa_direct */
struct vmbus_channel_packet_page_buffer {
u16 type;
@@ -1327,6 +1388,15 @@
0x8e, 0x77, 0x05, 0x58, 0xeb, 0x10, 0x73, 0xf8 \
}
+/*
+ * Synthetic FC GUID
+ * {2f9bcc4a-0069-4af3-b76b-6fd0be528cda}
+ */
+#define HV_SYNTHFC_GUID \
+ .guid = { \
+ 0x4A, 0xCC, 0x9B, 0x2F, 0x69, 0x00, 0xF3, 0x4A, \
+ 0xB7, 0x6B, 0x6F, 0xD0, 0xBE, 0x52, 0x8C, 0xDA \
+ }
/*
* Common header for Hyper-V ICs
diff --git a/include/linux/if_ether.h b/include/linux/if_ether.h
index 12b4d55..d556973 100644
--- a/include/linux/if_ether.h
+++ b/include/linux/if_ether.h
@@ -30,7 +30,6 @@
int eth_header_parse(const struct sk_buff *skb, unsigned char *haddr);
-int mac_pton(const char *s, u8 *mac);
extern ssize_t sysfs_format_mac(char *buf, const unsigned char *addr, int len);
#endif /* _LINUX_IF_ETHER_H */
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index e9ef6d6..3afb969 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -450,6 +450,8 @@
extern int hex_to_bin(char ch);
extern int __must_check hex2bin(u8 *dst, const char *src, size_t count);
+int mac_pton(const char *s, u8 *mac);
+
/*
* General tracing related utility functions - trace_printk(),
* tracing_on/tracing_off and tracing_start()/tracing_stop
diff --git a/lib/Kconfig b/lib/Kconfig
index fe01d41..d246a3b 100644
--- a/lib/Kconfig
+++ b/lib/Kconfig
@@ -22,6 +22,9 @@
config GENERIC_STRNLEN_USER
bool
+config GENERIC_NET_UTILS
+ bool
+
config GENERIC_FIND_FIRST_BIT
bool
diff --git a/lib/Makefile b/lib/Makefile
index c55a037..22f0f4e 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -137,6 +137,8 @@
obj-$(CONFIG_GENERIC_STRNCPY_FROM_USER) += strncpy_from_user.o
obj-$(CONFIG_GENERIC_STRNLEN_USER) += strnlen_user.o
+obj-$(CONFIG_GENERIC_NET_UTILS) += net_utils.o
+
obj-$(CONFIG_STMP_DEVICE) += stmp_device.o
libfdt_files = fdt.o fdt_ro.o fdt_wip.o fdt_rw.o fdt_sw.o fdt_strerror.o
diff --git a/lib/net_utils.c b/lib/net_utils.c
new file mode 100644
index 0000000..2e3c52c
--- /dev/null
+++ b/lib/net_utils.c
@@ -0,0 +1,26 @@
+#include <linux/string.h>
+#include <linux/if_ether.h>
+#include <linux/ctype.h>
+#include <linux/kernel.h>
+
+int mac_pton(const char *s, u8 *mac)
+{
+ int i;
+
+ /* XX:XX:XX:XX:XX:XX */
+ if (strlen(s) < 3 * ETH_ALEN - 1)
+ return 0;
+
+ /* Don't dirty result unless string is valid MAC. */
+ for (i = 0; i < ETH_ALEN; i++) {
+ if (!isxdigit(s[i * 3]) || !isxdigit(s[i * 3 + 1]))
+ return 0;
+ if (i != ETH_ALEN - 1 && s[i * 3 + 2] != ':')
+ return 0;
+ }
+ for (i = 0; i < ETH_ALEN; i++) {
+ mac[i] = (hex_to_bin(s[i * 3]) << 4) | hex_to_bin(s[i * 3 + 1]);
+ }
+ return 1;
+}
+EXPORT_SYMBOL(mac_pton);
diff --git a/net/Kconfig b/net/Kconfig
index 2ddc904..6dfe1c6 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -5,6 +5,7 @@
menuconfig NET
bool "Networking support"
select NLATTR
+ select GENERIC_NET_UTILS
---help---
Unless you really know what you are doing, you should say Y here.
The reason is that some programs need kernel networking support even
diff --git a/net/core/netpoll.c b/net/core/netpoll.c
index cec074b..35a9f080 100644
--- a/net/core/netpoll.c
+++ b/net/core/netpoll.c
@@ -12,6 +12,7 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/moduleparam.h>
+#include <linux/kernel.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/string.h>
diff --git a/net/core/utils.c b/net/core/utils.c
index 3c7f5b5..aa88e23 100644
--- a/net/core/utils.c
+++ b/net/core/utils.c
@@ -338,25 +338,3 @@
csum_unfold(*sum)));
}
EXPORT_SYMBOL(inet_proto_csum_replace16);
-
-int mac_pton(const char *s, u8 *mac)
-{
- int i;
-
- /* XX:XX:XX:XX:XX:XX */
- if (strlen(s) < 3 * ETH_ALEN - 1)
- return 0;
-
- /* Don't dirty result unless string is valid MAC. */
- for (i = 0; i < ETH_ALEN; i++) {
- if (!isxdigit(s[i * 3]) || !isxdigit(s[i * 3 + 1]))
- return 0;
- if (i != ETH_ALEN - 1 && s[i * 3 + 2] != ':')
- return 0;
- }
- for (i = 0; i < ETH_ALEN; i++) {
- mac[i] = (hex_to_bin(s[i * 3]) << 4) | hex_to_bin(s[i * 3 + 1]);
- }
- return 1;
-}
-EXPORT_SYMBOL(mac_pton);
diff --git a/tools/hv/hv_kvp_daemon.c b/tools/hv/hv_kvp_daemon.c
index 5a1f648..d55ce40 100644
--- a/tools/hv/hv_kvp_daemon.c
+++ b/tools/hv/hv_kvp_daemon.c
@@ -257,12 +257,15 @@
filep = fopen(fname, "re");
- if (!filep)
+ if (!filep) {
+ close(fd);
return 1;
+ }
record = malloc(alloc_unit * num_blocks);
if (record == NULL) {
fclose(filep);
+ close(fd);
return 1;
}
for (;;) {
@@ -286,6 +289,7 @@
num_blocks);
if (record == NULL) {
fclose(filep);
+ close(fd);
return 1;
}
continue;
@@ -765,7 +769,9 @@
break;
x = strchr(p, '\n');
- *x = '\0';
+ if (x)
+ *x = '\0';
+
strcat(config_buf, p);
strcat(config_buf, ";");
}
@@ -1457,7 +1463,13 @@
exit(EXIT_FAILURE);
}
nl_group = CN_KVP_IDX;
- setsockopt(fd, SOL_NETLINK, NETLINK_ADD_MEMBERSHIP, &nl_group, sizeof(nl_group));
+
+ if (setsockopt(fd, SOL_NETLINK, NETLINK_ADD_MEMBERSHIP, &nl_group, sizeof(nl_group)) < 0) {
+ syslog(LOG_ERR, "setsockopt failed; error: %d %s", errno, strerror(errno));
+ close(fd);
+ exit(EXIT_FAILURE);
+ }
+
/*
* Register ourselves with the kernel.
*/
@@ -1484,7 +1496,16 @@
socklen_t addr_l = sizeof(addr);
pfd.events = POLLIN;
pfd.revents = 0;
- poll(&pfd, 1, -1);
+
+ if (poll(&pfd, 1, -1) < 0) {
+ syslog(LOG_ERR, "poll failed; error: %d %s", errno, strerror(errno));
+ if (errno == EINVAL) {
+ close(fd);
+ exit(EXIT_FAILURE);
+ }
+ else
+ continue;
+ }
len = recvfrom(fd, kvp_recv_buffer, sizeof(kvp_recv_buffer), 0,
addr_p, &addr_l);