drm/i915: Fix scanoutpos calculations
The reported scanout position must be relative to the end of vblank.
Currently we manage to fumble that in a few ways.
First we don't consider the case when vtotal != vbl_end. While that
isn't very common (happens maybe only w/ old panel fitting hardware),
we can fix it easily enough.
The second issue is that on pre-CTG hardware we convert the pixel count
to horizontal/vertical components at the very beginning, and then forget
to adjust the horizontal component to be relative to vbl_end. So instead
we should keep our numbers in the pixel count domain while we're
adjusting the position to be relative to vbl_end. Then when we do the
conversion in the end, both vertical _and_ horizontal components will
come out correct.
v2: Change position to int from u32 to avoid sign issues
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: mario.kleiner.de@gmail.com
Tested-by: mario.kleiner.de@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index cc35d52..a923dea 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -599,7 +599,7 @@
struct drm_crtc *crtc = dev_priv->pipe_to_crtc_mapping[pipe];
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
const struct drm_display_mode *mode = &intel_crtc->config.adjusted_mode;
- u32 position;
+ int position;
int vbl_start, vbl_end, htotal, vtotal;
bool in_vbl = true;
int ret = 0;
@@ -621,13 +621,7 @@
/* No obvious pixelcount register. Only query vertical
* scanout position from Display scan line register.
*/
- position = I915_READ(PIPEDSL(pipe));
-
- /* Decode into vertical scanout position. Don't have
- * horizontal scanout position.
- */
- *vpos = position & 0x1fff;
- *hpos = 0;
+ position = I915_READ(PIPEDSL(pipe)) & 0x1fff;
} else {
/* Have access to pixelcount since start of frame.
* We can split this into vertical and horizontal
@@ -635,16 +629,33 @@
*/
position = (I915_READ(PIPEFRAMEPIXEL(pipe)) & PIPE_PIXEL_MASK) >> PIPE_PIXEL_SHIFT;
+ /* convert to pixel counts */
+ vbl_start *= htotal;
+ vbl_end *= htotal;
+ vtotal *= htotal;
+ }
+
+ in_vbl = position >= vbl_start && position < vbl_end;
+
+ /*
+ * While in vblank, position will be negative
+ * counting up towards 0 at vbl_end. And outside
+ * vblank, position will be positive counting
+ * up since vbl_end.
+ */
+ if (position >= vbl_start)
+ position -= vbl_end;
+ else
+ position += vtotal - vbl_end;
+
+ if (IS_G4X(dev) || INTEL_INFO(dev)->gen >= 5) {
+ *vpos = position;
+ *hpos = 0;
+ } else {
*vpos = position / htotal;
*hpos = position - (*vpos * htotal);
}
- in_vbl = *vpos >= vbl_start && *vpos < vbl_end;
-
- /* Inside "upper part" of vblank area? Apply corrective offset: */
- if (in_vbl && (*vpos >= vbl_start))
- *vpos = *vpos - vtotal;
-
/* In vblank? */
if (in_vbl)
ret |= DRM_SCANOUTPOS_INVBL;