USB: musb: Add new fifo table for a OMAP3 errata
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index b7e2d1b..c4893267 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1095,6 +1095,36 @@
{ .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
};
+/* mode 5 - fits in 8KB */
+static struct fifo_cfg __initdata mode_5_cfg[] = {
+{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
+{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
+{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
+{ .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
+{ .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, },
+{ .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, },
+{ .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, },
+{ .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, },
+{ .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, },
+{ .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, },
+{ .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 32, },
+{ .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 32, },
+{ .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 512, },
+{ .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, },
+{ .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
+};
/*
* configure a fifo; for non-shared endpoints, this may be called
@@ -1210,6 +1240,10 @@
cfg = mode_4_cfg;
n = ARRAY_SIZE(mode_4_cfg);
break;
+ case 5:
+ cfg = mode_5_cfg;
+ n = ARRAY_SIZE(mode_5_cfg);
+ break;
}
printk(KERN_DEBUG "%s: setup fifo_mode %d\n",