diff --git a/drivers/net/netxen/netxen_nic_niu.c b/drivers/net/netxen/netxen_nic_niu.c
new file mode 100644
index 0000000..6e421c8
--- /dev/null
+++ b/drivers/net/netxen/netxen_nic_niu.c
@@ -0,0 +1,800 @@
+/*
+ * Copyright (C) 2003 - 2006 NetXen, Inc.
+ * All rights reserved.
+ * 
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *                            
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *                                   
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston,
+ * MA  02111-1307, USA.
+ * 
+ * The full GNU General Public License is included in this distribution
+ * in the file called LICENSE.
+ * 
+ * Contact Information:
+ *    info@netxen.com
+ * NetXen,
+ * 3965 Freedom Circle, Fourth floor,
+ * Santa Clara, CA 95054
+ *
+ *
+ * Provides access to the Network Interface Unit h/w block.
+ *
+ */
+
+#include "netxen_nic.h"
+#include <linux/delay.h>
+
+/* 
+ * netxen_niu_gbe_phy_read - read a register from the GbE PHY via
+ * mii management interface.
+ *
+ * Note: The MII management interface goes through port 0.
+ *       Individual phys are addressed as follows:
+ * @param phy  [15:8]  phy id
+ * @param reg  [7:0]   register number
+ *
+ * @returns  0 on success
+ *          -1 on error
+ *
+ */
+int netxen_niu_gbe_phy_read(struct netxen_adapter *adapter, long phy,
+			    long reg, __le32 * readval)
+{
+	long timeout = 0;
+	long result = 0;
+	long restore = 0;
+	__le32 address;
+	__le32 command;
+	__le32 status;
+	__le32 mii_cfg;
+	__le32 mac_cfg0;
+
+	/* MII mgmt all goes through port 0 MAC interface, so it cannot be in reset */
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(0),
+				  &mac_cfg0, 4))
+		return -EIO;
+	if (netxen_gb_get_soft_reset(mac_cfg0)) {
+		__le32 temp;
+		temp = 0;
+		netxen_gb_tx_reset_pb(temp);
+		netxen_gb_rx_reset_pb(temp);
+		netxen_gb_tx_reset_mac(temp);
+		netxen_gb_rx_reset_mac(temp);
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_0(0),
+					   &temp, 4))
+			return -EIO;
+		restore = 1;
+	}
+
+	/* reset MII management interface */
+	mii_cfg = 0;
+	netxen_gb_set_mii_mgmt_clockselect(mii_cfg, 7);
+	netxen_gb_mii_mgmt_reset(mii_cfg);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_CONFIG(0),
+				   &mii_cfg, 4))
+		return -EIO;
+	netxen_gb_mii_mgmt_unset(mii_cfg);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_CONFIG(0),
+				   &mii_cfg, 4))
+		return -EIO;
+
+	address = 0;
+	netxen_gb_mii_mgmt_reg_addr(address, reg);
+	netxen_gb_mii_mgmt_phy_addr(address, phy);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_ADDR(0),
+				   &address, 4))
+		return -EIO;
+	command = 0;		/* turn off any prior activity */
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_COMMAND(0),
+				   &command, 4))
+		return -EIO;
+	/* send read command */
+	netxen_gb_mii_mgmt_set_read_cycle(command);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_COMMAND(0),
+				   &command, 4))
+		return -EIO;
+
+	status = 0;
+	do {
+		if (netxen_nic_hw_read_wx(adapter,
+					  NETXEN_NIU_GB_MII_MGMT_INDICATE(0),
+					  &status, 4))
+			return -EIO;
+		timeout++;
+	} while ((netxen_get_gb_mii_mgmt_busy(status)
+		  || netxen_get_gb_mii_mgmt_notvalid(status))
+		 && (timeout++ < NETXEN_NIU_PHY_WAITMAX));
+
+	if (timeout < NETXEN_NIU_PHY_WAITMAX) {
+		if (netxen_nic_hw_read_wx(adapter,
+					  NETXEN_NIU_GB_MII_MGMT_STATUS(0),
+					  readval, 4))
+			return -EIO;
+		result = 0;
+	} else
+		result = -1;
+
+	if (restore)
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_0(0),
+					   &mac_cfg0, 4))
+			return -EIO;
+
+	return result;
+}
+
+/* 
+ * netxen_niu_gbe_phy_write - write a register to the GbE PHY via
+ * mii management interface.
+ *
+ * Note: The MII management interface goes through port 0.
+ *       Individual phys are addressed as follows:
+ * @param phy      [15:8]  phy id
+ * @param reg      [7:0]   register number
+ *
+ * @returns  0 on success
+ *          -1 on error
+ *
+ */
+int netxen_niu_gbe_phy_write(struct netxen_adapter *adapter,
+			     long phy, long reg, __le32 val)
+{
+	long timeout = 0;
+	long result = 0;
+	long restore = 0;
+	__le32 address;
+	__le32 command;
+	__le32 status;
+	__le32 mac_cfg0;
+
+	/* MII mgmt all goes through port 0 MAC interface, so it cannot be in reset */
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(0),
+				  &mac_cfg0, 4))
+		return -EIO;
+	if (netxen_gb_get_soft_reset(mac_cfg0)) {
+		__le32 temp;
+		temp = 0;
+		netxen_gb_tx_reset_pb(temp);
+		netxen_gb_rx_reset_pb(temp);
+		netxen_gb_tx_reset_mac(temp);
+		netxen_gb_rx_reset_mac(temp);
+
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_0(0),
+					   &temp, 4))
+			return -EIO;
+		restore = 1;
+	}
+
+	command = 0;		/* turn off any prior activity */
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_COMMAND(0),
+				   &command, 4))
+		return -EIO;
+
+	address = 0;
+	netxen_gb_mii_mgmt_reg_addr(address, reg);
+	netxen_gb_mii_mgmt_phy_addr(address, phy);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_ADDR(0),
+				   &address, 4))
+		return -EIO;
+
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_CTRL(0),
+				   &val, 4))
+		return -EIO;
+
+	status = 0;
+	do {
+		if (netxen_nic_hw_read_wx(adapter,
+					  NETXEN_NIU_GB_MII_MGMT_INDICATE(0),
+					  &status, 4))
+			return -EIO;
+		timeout++;
+	} while ((netxen_get_gb_mii_mgmt_busy(status))
+		 && (timeout++ < NETXEN_NIU_PHY_WAITMAX));
+
+	if (timeout < NETXEN_NIU_PHY_WAITMAX)
+		result = 0;
+	else
+		result = -EIO;
+
+	/* restore the state of port 0 MAC in case we tampered with it */
+	if (restore)
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_0(0),
+					   &mac_cfg0, 4))
+			return -EIO;
+
+	return result;
+}
+
+int netxen_niu_xgbe_enable_phy_interrupts(struct netxen_adapter *adapter,
+					  int port)
+{
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_INT_MASK, 0x3f);
+	return 0;
+}
+
+int netxen_niu_gbe_enable_phy_interrupts(struct netxen_adapter *adapter,
+					 int port)
+{
+	int result = 0;
+	__le32 enable = 0;
+	netxen_set_phy_int_link_status_changed(enable);
+	netxen_set_phy_int_autoneg_completed(enable);
+	netxen_set_phy_int_speed_changed(enable);
+
+	if (0 !=
+	    netxen_niu_gbe_phy_write(adapter, port,
+				     NETXEN_NIU_GB_MII_MGMT_ADDR_INT_ENABLE,
+				     enable))
+		result = -EIO;
+
+	return result;
+}
+
+int netxen_niu_xgbe_disable_phy_interrupts(struct netxen_adapter *adapter,
+					   int port)
+{
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_INT_MASK, 0x7f);
+	return 0;
+}
+
+int netxen_niu_gbe_disable_phy_interrupts(struct netxen_adapter *adapter,
+					  int port)
+{
+	int result = 0;
+	if (0 !=
+	    netxen_niu_gbe_phy_write(adapter, port,
+				     NETXEN_NIU_GB_MII_MGMT_ADDR_INT_ENABLE, 0))
+		result = -EIO;
+
+	return result;
+}
+
+int netxen_niu_xgbe_clear_phy_interrupts(struct netxen_adapter *adapter,
+					 int port)
+{
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_ACTIVE_INT, -1);
+	return 0;
+}
+
+int netxen_niu_gbe_clear_phy_interrupts(struct netxen_adapter *adapter,
+					int port)
+{
+	int result = 0;
+	if (0 !=
+	    netxen_niu_gbe_phy_write(adapter, port,
+				     NETXEN_NIU_GB_MII_MGMT_ADDR_INT_STATUS,
+				     -EIO))
+		result = -EIO;
+
+	return result;
+}
+
+/* 
+ * netxen_niu_gbe_set_mii_mode- Set 10/100 Mbit Mode for GbE MAC
+ *
+ */
+void netxen_niu_gbe_set_mii_mode(struct netxen_adapter *adapter,
+				 int port, long enable)
+{
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_MODE, 0x2);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				    0x80000000);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				    0x0000f0025);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_1(port),
+				    0xf1ff);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB0_GMII_MODE + (port << 3), 0);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB0_MII_MODE + (port << 3), 1);
+	netxen_crb_writelit_adapter(adapter,
+				    (NETXEN_NIU_GB0_HALF_DUPLEX + port * 4), 0);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB_MII_MGMT_CONFIG(port), 0x7);
+
+	if (enable) {
+		/* 
+		 * Do NOT enable flow control until a suitable solution for 
+		 *  shutting down pause frames is found. 
+		 */
+		netxen_crb_writelit_adapter(adapter,
+					    NETXEN_NIU_GB_MAC_CONFIG_0(port),
+					    0x5);
+	}
+
+	if (netxen_niu_gbe_enable_phy_interrupts(adapter, port))
+		printk(KERN_ERR PFX "ERROR enabling PHY interrupts\n");
+	if (netxen_niu_gbe_clear_phy_interrupts(adapter, port))
+		printk(KERN_ERR PFX "ERROR clearing PHY interrupts\n");
+}
+
+/* 
+ * netxen_niu_gbe_set_gmii_mode- Set GbE Mode for GbE MAC
+ */
+void netxen_niu_gbe_set_gmii_mode(struct netxen_adapter *adapter,
+				  int port, long enable)
+{
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_MODE, 0x2);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				    0x80000000);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				    0x0000f0025);
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB_MAC_CONFIG_1(port),
+				    0xf2ff);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB0_MII_MODE + (port << 3), 0);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB0_GMII_MODE + (port << 3), 1);
+	netxen_crb_writelit_adapter(adapter,
+				    (NETXEN_NIU_GB0_HALF_DUPLEX + port * 4), 0);
+	netxen_crb_writelit_adapter(adapter,
+				    NETXEN_NIU_GB_MII_MGMT_CONFIG(port), 0x7);
+
+	if (enable) {
+		/* 
+		 * Do NOT enable flow control until a suitable solution for 
+		 *  shutting down pause frames is found. 
+		 */
+		netxen_crb_writelit_adapter(adapter,
+					    NETXEN_NIU_GB_MAC_CONFIG_0(port),
+					    0x5);
+	}
+
+	if (netxen_niu_gbe_enable_phy_interrupts(adapter, port))
+		printk(KERN_ERR PFX "ERROR enabling PHY interrupts\n");
+	if (netxen_niu_gbe_clear_phy_interrupts(adapter, port))
+		printk(KERN_ERR PFX "ERROR clearing PHY interrupts\n");
+}
+
+int netxen_niu_gbe_init_port(struct netxen_adapter *adapter, int port)
+{
+	int result = 0;
+	__le32 status;
+	if (adapter->ops->disable_phy_interrupts)
+		adapter->ops->disable_phy_interrupts(adapter, port);
+	mdelay(2);
+
+	if (0 ==
+	    netxen_niu_gbe_phy_read(adapter, port,
+				    NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS,
+				    (__le32 *) & status)) {
+		if (netxen_get_phy_link(status)) {
+			if (netxen_get_phy_speed(status) == 2) {
+				netxen_niu_gbe_set_gmii_mode(adapter, port, 1);
+			} else if ((netxen_get_phy_speed(status) == 1)
+				   || (netxen_get_phy_speed(status) == 0)) {
+				netxen_niu_gbe_set_mii_mode(adapter, port, 1);
+			} else {
+				result = -1;
+			}
+
+		} else {
+			/* We don't have link. Cable  must be unconnected. */
+			/* Enable phy interrupts so we take action when plugged in */
+			netxen_crb_writelit_adapter(adapter,
+						    NETXEN_NIU_GB_MAC_CONFIG_0
+						    (port), 0x80000000);
+			netxen_crb_writelit_adapter(adapter,
+						    NETXEN_NIU_GB_MAC_CONFIG_0
+						    (port), 0x0000f0025);
+			if (netxen_niu_gbe_clear_phy_interrupts(adapter, port))
+				printk(KERN_ERR PFX
+				       "ERROR clearing PHY interrupts\n");
+			if (netxen_niu_gbe_enable_phy_interrupts(adapter, port))
+				printk(KERN_ERR PFX
+				       "ERROR enabling PHY interrupts\n");
+			if (netxen_niu_gbe_clear_phy_interrupts(adapter, port))
+				printk(KERN_ERR PFX
+				       "ERROR clearing PHY interrupts\n");
+			result = -1;
+		}
+	} else {
+		result = -EIO;
+	}
+	return result;
+}
+
+/* 
+ * netxen_niu_gbe_handle_phy_interrupt - Handles GbE PHY interrupts
+ * @param enable 0 means don't enable the port
+ *               1 means enable (or re-enable) the port
+ */
+int netxen_niu_gbe_handle_phy_interrupt(struct netxen_adapter *adapter,
+					int port, long enable)
+{
+	int result = 0;
+	__le32 int_src;
+
+	printk(KERN_INFO PFX "NETXEN: Handling PHY interrupt on port %d"
+	       " (device enable = %d)\n", (int)port, (int)enable);
+
+	/* The read of the PHY INT status will clear the pending interrupt status */
+	if (netxen_niu_gbe_phy_read(adapter, port,
+				    NETXEN_NIU_GB_MII_MGMT_ADDR_INT_STATUS,
+				    &int_src) != 0)
+		result = -EINVAL;
+	else {
+		printk(KERN_INFO PFX "PHY Interrupt source = 0x%x \n", int_src);
+		if (netxen_get_phy_int_jabber(int_src))
+			printk(KERN_INFO PFX "jabber Interrupt ");
+		if (netxen_get_phy_int_polarity_changed(int_src))
+			printk(KERN_INFO PFX "polarity changed ");
+		if (netxen_get_phy_int_energy_detect(int_src))
+			printk(KERN_INFO PFX "energy detect \n");
+		if (netxen_get_phy_int_downshift(int_src))
+			printk(KERN_INFO PFX "downshift \n");
+		if (netxen_get_phy_int_mdi_xover_changed(int_src))
+			printk(KERN_INFO PFX "mdi_xover_changed ");
+		if (netxen_get_phy_int_fifo_over_underflow(int_src))
+			printk(KERN_INFO PFX "fifo_over_underflow ");
+		if (netxen_get_phy_int_false_carrier(int_src))
+			printk(KERN_INFO PFX "false_carrier ");
+		if (netxen_get_phy_int_symbol_error(int_src))
+			printk(KERN_INFO PFX "symbol_error ");
+		if (netxen_get_phy_int_autoneg_completed(int_src))
+			printk(KERN_INFO PFX "autoneg_completed ");
+		if (netxen_get_phy_int_page_received(int_src))
+			printk(KERN_INFO PFX "page_received ");
+		if (netxen_get_phy_int_duplex_changed(int_src))
+			printk(KERN_INFO PFX "duplex_changed ");
+		if (netxen_get_phy_int_autoneg_error(int_src))
+			printk(KERN_INFO PFX "autoneg_error ");
+		if ((netxen_get_phy_int_speed_changed(int_src))
+		    || (netxen_get_phy_int_link_status_changed(int_src))) {
+			__le32 status;
+
+			printk(KERN_INFO PFX
+			       "speed_changed or link status changed");
+			if (netxen_niu_gbe_phy_read
+			    (adapter, port,
+			     NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS,
+			     &status) == 0) {
+				if (netxen_get_phy_speed(status) == 2) {
+					printk
+					    (KERN_INFO PFX "Link speed changed"
+					     " to 1000 Mbps\n");
+					netxen_niu_gbe_set_gmii_mode(adapter,
+								     port,
+								     enable);
+				} else if (netxen_get_phy_speed(status) == 1) {
+					printk
+					    (KERN_INFO PFX "Link speed changed"
+					     " to 100 Mbps\n");
+					netxen_niu_gbe_set_mii_mode(adapter,
+								    port,
+								    enable);
+				} else if (netxen_get_phy_speed(status) == 0) {
+					printk
+					    (KERN_INFO PFX "Link speed changed"
+					     " to 10 Mbps\n");
+					netxen_niu_gbe_set_mii_mode(adapter,
+								    port,
+								    enable);
+				} else {
+					printk(KERN_ERR PFX "ERROR reading"
+					       "PHY status. Illegal speed.\n");
+					result = -1;
+				}
+			} else {
+				printk(KERN_ERR PFX
+				       "ERROR reading PHY status.\n");
+				result = -1;
+			}
+
+		}
+		printk(KERN_INFO "\n");
+	}
+	return result;
+}
+
+/*
+ * Return the current station MAC address.
+ * Note that the passed-in value must already be in network byte order.
+ */
+int netxen_niu_macaddr_get(struct netxen_adapter *adapter,
+			   int phy, netxen_ethernet_macaddr_t * addr)
+{
+	u64 result = 0;
+	__le32 stationhigh;
+	__le32 stationlow;
+
+	if (addr == NULL)
+		return -EINVAL;
+	if ((phy < 0) || (phy > 3))
+		return -EINVAL;
+
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_GB_STATION_ADDR_0(phy),
+				  &stationhigh, 4))
+		return -EIO;
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_GB_STATION_ADDR_1(phy),
+				  &stationlow, 4))
+		return -EIO;
+
+	result = (u64) netxen_gb_get_stationaddress_low(stationlow);
+	result |= (u64) stationhigh << 16;
+	memcpy(*addr, &result, sizeof(netxen_ethernet_macaddr_t));
+
+	return 0;
+}
+
+/*
+ * Set the station MAC address.
+ * Note that the passed-in value must already be in network byte order.
+ */
+int netxen_niu_macaddr_set(struct netxen_port *port,
+			   netxen_ethernet_macaddr_t addr)
+{
+	__le32 temp = 0;
+	struct netxen_adapter *adapter = port->adapter;
+	int phy = port->portnum;
+
+	memcpy(&temp, addr, 2);
+	temp <<= 16;
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_STATION_ADDR_1(phy),
+				   &temp, 4))
+		return -EIO;
+
+	temp = 0;
+
+	memcpy(&temp, ((u8 *) addr) + 2, sizeof(__le32));
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_STATION_ADDR_0(phy),
+				   &temp, 4))
+		return -2;
+
+	return 0;
+}
+
+/* Enable a GbE interface */
+int netxen_niu_enable_gbe_port(struct netxen_adapter *adapter,
+			       int port, netxen_niu_gbe_ifmode_t mode)
+{
+	__le32 mac_cfg0;
+	__le32 mac_cfg1;
+	__le32 mii_cfg;
+
+	if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS))
+		return -EINVAL;
+
+	mac_cfg0 = 0;
+	netxen_gb_soft_reset(mac_cfg0);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				   &mac_cfg0, 4))
+		return -EIO;
+	mac_cfg0 = 0;
+	netxen_gb_enable_tx(mac_cfg0);
+	netxen_gb_enable_rx(mac_cfg0);
+	netxen_gb_unset_rx_flowctl(mac_cfg0);
+	netxen_gb_tx_reset_pb(mac_cfg0);
+	netxen_gb_rx_reset_pb(mac_cfg0);
+	netxen_gb_tx_reset_mac(mac_cfg0);
+	netxen_gb_rx_reset_mac(mac_cfg0);
+
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				   &mac_cfg0, 4))
+		return -EIO;
+	mac_cfg1 = 0;
+	netxen_gb_set_preamblelen(mac_cfg1, 0xf);
+	netxen_gb_set_duplex(mac_cfg1);
+	netxen_gb_set_crc_enable(mac_cfg1);
+	netxen_gb_set_padshort(mac_cfg1);
+	netxen_gb_set_checklength(mac_cfg1);
+	netxen_gb_set_hugeframes(mac_cfg1);
+
+	if (mode == NETXEN_NIU_10_100_MB) {
+		netxen_gb_set_intfmode(mac_cfg1, 1);
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_1(port),
+					   &mac_cfg1, 4))
+			return -EIO;
+
+		/* set mii mode */
+		netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB0_GMII_MODE +
+					    (port << 3), 0);
+		netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB0_MII_MODE +
+					    (port << 3), 1);
+
+	} else if (mode == NETXEN_NIU_1000_MB) {
+		netxen_gb_set_intfmode(mac_cfg1, 2);
+		if (netxen_nic_hw_write_wx(adapter,
+					   NETXEN_NIU_GB_MAC_CONFIG_1(port),
+					   &mac_cfg1, 4))
+			return -EIO;
+		/* set gmii mode */
+		netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB0_MII_MODE +
+					    (port << 3), 0);
+		netxen_crb_writelit_adapter(adapter, NETXEN_NIU_GB0_GMII_MODE +
+					    (port << 3), 1);
+	}
+	mii_cfg = 0;
+	netxen_gb_set_mii_mgmt_clockselect(mii_cfg, 7);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MII_MGMT_CONFIG(port),
+				   &mii_cfg, 4))
+		return -EIO;
+	mac_cfg0 = 0;
+	netxen_gb_enable_tx(mac_cfg0);
+	netxen_gb_enable_rx(mac_cfg0);
+	netxen_gb_unset_rx_flowctl(mac_cfg0);
+	netxen_gb_unset_tx_flowctl(mac_cfg0);
+
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				   &mac_cfg0, 4))
+		return -EIO;
+	return 0;
+}
+
+/* Disable a GbE interface */
+int netxen_niu_disable_gbe_port(struct netxen_adapter *adapter, int port)
+{
+	__le32 mac_cfg0;
+
+	if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS))
+		return -EINVAL;
+
+	mac_cfg0 = 0;
+	netxen_gb_soft_reset(mac_cfg0);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_MAC_CONFIG_0(port),
+				   &mac_cfg0, 4))
+		return -EIO;
+	return 0;
+}
+
+/* Disable an XG interface */
+int netxen_niu_disable_xg_port(struct netxen_adapter *adapter, int port)
+{
+	__le32 mac_cfg;
+
+	if (port != 0)
+		return -EINVAL;
+
+	mac_cfg = 0;
+	netxen_xg_soft_reset(mac_cfg);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_XGE_CONFIG_0,
+				   &mac_cfg, 4))
+		return -EIO;
+	return 0;
+}
+
+/* Set promiscuous mode for a GbE interface */
+int netxen_niu_set_promiscuous_mode(struct netxen_adapter *adapter, int port,
+				    netxen_niu_prom_mode_t mode)
+{
+	__le32 reg;
+
+	if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS))
+		return -EINVAL;
+
+	/* save previous contents */
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_GB_DROP_WRONGADDR,
+				  &reg, 4))
+		return -EIO;
+	if (mode == NETXEN_NIU_PROMISC_MODE) {
+		switch (port) {
+		case 0:
+			netxen_clear_gb_drop_gb0(reg);
+			break;
+		case 1:
+			netxen_clear_gb_drop_gb1(reg);
+			break;
+		case 2:
+			netxen_clear_gb_drop_gb2(reg);
+			break;
+		case 3:
+			netxen_clear_gb_drop_gb3(reg);
+			break;
+		default:
+			return -EIO;
+		}
+	} else {
+		switch (port) {
+		case 0:
+			netxen_set_gb_drop_gb0(reg);
+			break;
+		case 1:
+			netxen_set_gb_drop_gb1(reg);
+			break;
+		case 2:
+			netxen_set_gb_drop_gb2(reg);
+			break;
+		case 3:
+			netxen_set_gb_drop_gb3(reg);
+			break;
+		default:
+			return -EIO;
+		}
+	}
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_GB_DROP_WRONGADDR,
+				   &reg, 4))
+		return -EIO;
+	return 0;
+}
+
+/*
+ * Set the MAC address for an XG port
+ * Note that the passed-in value must already be in network byte order.
+ */
+int netxen_niu_xg_macaddr_set(struct netxen_port *port,
+			      netxen_ethernet_macaddr_t addr)
+{
+	__le32 temp = 0;
+	struct netxen_adapter *adapter = port->adapter;
+
+	memcpy(&temp, addr, 2);
+	temp = cpu_to_le32(temp);
+	temp <<= 16;
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_XGE_STATION_ADDR_0_1,
+				   &temp, 4))
+		return -EIO;
+
+	temp = 0;
+
+	memcpy(&temp, ((u8 *) addr) + 2, sizeof(__le32));
+	temp = cpu_to_le32(temp);
+	if (netxen_nic_hw_write_wx(adapter, NETXEN_NIU_XGE_STATION_ADDR_0_HI,
+				   &temp, 4))
+		return -EIO;
+
+	return 0;
+}
+
+/*
+ * Return the current station MAC address.
+ * Note that the passed-in value must already be in network byte order.
+ */
+int netxen_niu_xg_macaddr_get(struct netxen_adapter *adapter, int phy,
+			      netxen_ethernet_macaddr_t * addr)
+{
+	__le32 stationhigh;
+	__le32 stationlow;
+	u64 result;
+
+	if (addr == NULL)
+		return -EINVAL;
+	if (phy != 0)
+		return -EINVAL;
+
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_XGE_STATION_ADDR_0_HI,
+				  &stationhigh, 4))
+		return -EIO;
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_XGE_STATION_ADDR_0_1,
+				  &stationlow, 4))
+		return -EIO;
+
+	result = ((u64) stationlow) >> 16;
+	result |= (u64) stationhigh << 16;
+	memcpy(*addr, &result, sizeof(netxen_ethernet_macaddr_t));
+
+	return 0;
+}
+
+int netxen_niu_xg_set_promiscuous_mode(struct netxen_adapter *adapter,
+				       int port, netxen_niu_prom_mode_t mode)
+{
+	__le32 reg;
+
+	if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS))
+		return -EINVAL;
+
+	if (netxen_nic_hw_read_wx(adapter, NETXEN_NIU_XGE_CONFIG_1, &reg, 4))
+		return -EIO;
+	if (mode == NETXEN_NIU_PROMISC_MODE)
+		reg = (reg | 0x2000UL);
+	else
+		reg = (reg & ~0x2000UL);
+
+	netxen_crb_writelit_adapter(adapter, NETXEN_NIU_XGE_CONFIG_1, reg);
+
+	return 0;
+}