phy: ti-pipe3: use *syscon* framework API to set PCS value of the PHY
Deprecate using phy-omap-control driver to set PCS value of the PHY
and start using *syscon* API to do the same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
index e06f980..49e5b0c 100644
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -83,6 +83,8 @@
- syscon-pllreset: Handle to system control region that contains the
CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
+ - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
+ register offset to write the PCS delay value.
Deprecated properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index a47b190..0a477d2 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -65,6 +65,9 @@
#define PIPE3_PHY_TX_RX_POWERON 0x3
#define PIPE3_PHY_TX_RX_POWEROFF 0x0
+#define PCIE_PCS_MASK 0xFF0000
+#define PCIE_PCS_DELAY_COUNT_SHIFT 0x10
+
/*
* This is an Empirical value that works, need to confirm the actual
* value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
@@ -96,9 +99,11 @@
struct clk *div_clk;
struct pipe3_dpll_map *dpll_map;
struct regmap *phy_power_syscon; /* ctrl. reg. acces */
+ struct regmap *pcs_syscon; /* ctrl. reg. acces */
struct regmap *dpll_reset_syscon; /* ctrl. reg. acces */
unsigned int dpll_reset_reg; /* reg. index within syscon */
unsigned int power_reg; /* power reg. index within syscon */
+ unsigned int pcie_pcs_reg; /* pcs reg. index in syscon */
bool sata_refclk_enabled;
};
@@ -269,8 +274,15 @@
* 18-1804.
*/
if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
- omap_control_pcie_pcs(phy->control_dev, 0x96);
- return 0;
+ if (!phy->pcs_syscon) {
+ omap_control_pcie_pcs(phy->control_dev, 0x96);
+ return 0;
+ }
+
+ val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT;
+ ret = regmap_update_bits(phy->pcs_syscon, phy->pcie_pcs_reg,
+ PCIE_PCS_MASK, val);
+ return ret;
}
/* Bring it out of IDLE if it is IDLE */
@@ -455,6 +467,24 @@
phy->control_dev = &control_pdev->dev;
}
+ if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
+ phy->pcs_syscon = syscon_regmap_lookup_by_phandle(node,
+ "syscon-pcs");
+ if (IS_ERR(phy->pcs_syscon)) {
+ dev_dbg(dev,
+ "can't get syscon-pcs, using omap control\n");
+ phy->pcs_syscon = NULL;
+ } else {
+ if (of_property_read_u32_index(node,
+ "syscon-pcs", 1,
+ &phy->pcie_pcs_reg)) {
+ dev_err(dev,
+ "couldn't get pcie pcs reg. offset\n");
+ return -EINVAL;
+ }
+ }
+ }
+
if (of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
phy->dpll_reset_syscon = syscon_regmap_lookup_by_phandle(node,
"syscon-pllreset");