UBI: fix s/then/than/ typos
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
diff --git a/drivers/mtd/ubi/Kconfig b/drivers/mtd/ubi/Kconfig
index 0a8c7ea..f702a16 100644
--- a/drivers/mtd/ubi/Kconfig
+++ b/drivers/mtd/ubi/Kconfig
@@ -27,7 +27,7 @@
The default value should be OK for SLC NAND flashes, NOR flashes and
other flashes which have eraseblock life-cycle 100000 or more.
However, in case of MLC NAND flashes which typically have eraseblock
- life-cycle less then 10000, the threshold should be lessened (e.g.,
+ life-cycle less than 10000, the threshold should be lessened (e.g.,
to 128 or 256, although it does not have to be power of 2).
config MTD_UBI_BEB_RESERVE
diff --git a/drivers/mtd/ubi/io.c b/drivers/mtd/ubi/io.c
index 533b1a4..016ec13 100644
--- a/drivers/mtd/ubi/io.c
+++ b/drivers/mtd/ubi/io.c
@@ -65,7 +65,7 @@
*
* A: because when writing a sub-page, MTD still writes a full 2K page but the
* bytes which are no relevant to the sub-page are 0xFF. So, basically, writing
- * 4x512 sub-pages is 4 times slower then writing one 2KiB NAND page. Thus, we
+ * 4x512 sub-pages is 4 times slower than writing one 2KiB NAND page. Thus, we
* prefer to use sub-pages only for EV and VID headers.
*
* As it was noted above, the VID header may start at a non-aligned offset.
diff --git a/drivers/mtd/ubi/kapi.c b/drivers/mtd/ubi/kapi.c
index 17f287d..69fa4ef0 100644
--- a/drivers/mtd/ubi/kapi.c
+++ b/drivers/mtd/ubi/kapi.c
@@ -488,7 +488,7 @@
*
* This function changes the contents of a logical eraseblock atomically. @buf
* has to contain new logical eraseblock data, and @len - the length of the
- * data, which has to be aligned. The length may be shorter then the logical
+ * data, which has to be aligned. The length may be shorter than the logical
* eraseblock size, ant the logical eraseblock may be appended to more times
* later on. This function guarantees that in case of an unclean reboot the old
* contents is preserved. Returns zero in case of success and a negative error
@@ -571,7 +571,7 @@
*
* This function un-maps logical eraseblock @lnum and schedules the
* corresponding physical eraseblock for erasure, so that it will eventually be
- * physically erased in background. This operation is much faster then the
+ * physically erased in background. This operation is much faster than the
* erase operation.
*
* Unlike erase, the un-map operation does not guarantee that the logical
@@ -590,7 +590,7 @@
*
* The main and obvious use-case of this function is when the contents of a
* logical eraseblock has to be re-written. Then it is much more efficient to
- * first un-map it, then write new data, rather then first erase it, then write
+ * first un-map it, then write new data, rather than first erase it, then write
* new data. Note, once new data has been written to the logical eraseblock,
* UBI guarantees that the old contents has gone forever. In other words, if an
* unclean reboot happens after the logical eraseblock has been un-mapped and
diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c
index dc5f688..aed19f3 100644
--- a/drivers/mtd/ubi/scan.c
+++ b/drivers/mtd/ubi/scan.c
@@ -231,7 +231,7 @@
* case of success this function returns a positive value, in case of failure, a
* negative error code is returned. The success return codes use the following
* bits:
- * o bit 0 is cleared: the first PEB (described by @seb) is newer then the
+ * o bit 0 is cleared: the first PEB (described by @seb) is newer than the
* second PEB (described by @pnum and @vid_hdr);
* o bit 0 is set: the second PEB is newer;
* o bit 1 is cleared: no bit-flips were detected in the newer LEB;
@@ -452,7 +452,7 @@
if (cmp_res & 1) {
/*
- * This logical eraseblock is newer then the one
+ * This logical eraseblock is newer than the one
* found earlier.
*/
err = validate_vid_hdr(vid_hdr, sv, pnum);
diff --git a/drivers/mtd/ubi/wl.c b/drivers/mtd/ubi/wl.c
index f64ddab..ee7b1d8 100644
--- a/drivers/mtd/ubi/wl.c
+++ b/drivers/mtd/ubi/wl.c
@@ -350,7 +350,7 @@
* @max: highest possible erase counter
*
* This function looks for a wear leveling entry with erase counter closest to
- * @max and less then @max.
+ * @max and less than @max.
*/
static struct ubi_wl_entry *find_wl_entry(struct rb_root *root, int max)
{