usb/xhci: group MSI interrupt registration into its own function
This patch moves the complete MSI/MSI-X/Legacy dance into its own
function. There is however one difference: If the XHCI_BROKEN_MSI flag
is set then we don't free and register the irq, we simply return.
This is preparation for later PCI decouple.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 7bf8677..583a3e3 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -397,6 +397,45 @@
return 0;
}
+static int xhci_try_enable_msi(struct usb_hcd *hcd)
+{
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
+ int ret;
+
+ /*
+ * Some Fresco Logic host controllers advertise MSI, but fail to
+ * generate interrupts. Don't even try to enable MSI.
+ */
+ if (xhci->quirks & XHCI_BROKEN_MSI)
+ return 0;
+
+ /* unregister the legacy interrupt */
+ if (hcd->irq)
+ free_irq(hcd->irq, hcd);
+ hcd->irq = -1;
+
+ ret = xhci_setup_msix(xhci);
+ if (ret)
+ /* fall back to msi*/
+ ret = xhci_setup_msi(xhci);
+
+ if (!ret)
+ /* hcd->irq is -1, we have MSI */
+ return 0;
+
+ /* fall back to legacy interrupt*/
+ ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
+ hcd->irq_descr, hcd);
+ if (ret) {
+ xhci_err(xhci, "request interrupt %d failed\n",
+ pdev->irq);
+ return ret;
+ }
+ hcd->irq = pdev->irq;
+ return 0;
+}
+
/*
* Start the HC after it was halted.
*
@@ -413,9 +452,8 @@
{
u32 temp;
u64 temp_64;
- u32 ret;
+ int ret;
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
- struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
/* Start the xHCI host controller running only after the USB 2.0 roothub
* is setup.
@@ -426,34 +464,10 @@
return xhci_run_finished(xhci);
xhci_dbg(xhci, "xhci_run\n");
- /* unregister the legacy interrupt */
- if (hcd->irq)
- free_irq(hcd->irq, hcd);
- hcd->irq = -1;
- /* Some Fresco Logic host controllers advertise MSI, but fail to
- * generate interrupts. Don't even try to enable MSI.
- */
- if (xhci->quirks & XHCI_BROKEN_MSI)
- goto legacy_irq;
-
- ret = xhci_setup_msix(xhci);
+ ret = xhci_try_enable_msi(hcd);
if (ret)
- /* fall back to msi*/
- ret = xhci_setup_msi(xhci);
-
- if (ret) {
-legacy_irq:
- /* fall back to legacy interrupt*/
- ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
- hcd->irq_descr, hcd);
- if (ret) {
- xhci_err(xhci, "request interrupt %d failed\n",
- pdev->irq);
- return ret;
- }
- hcd->irq = pdev->irq;
- }
+ return ret;
#ifdef CONFIG_USB_XHCI_HCD_DEBUGGING
init_timer(&xhci->event_ring_timer);