| /* |
| * Copyright (C) 2005-2006 Atmel Corporation |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dw_dmac.h> |
| #include <linux/fb.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/slab.h> |
| #include <linux/gpio.h> |
| #include <linux/spi/spi.h> |
| #include <linux/usb/atmel_usba_udc.h> |
| |
| #include <mach/atmel-mci.h> |
| #include <linux/atmel-mci.h> |
| |
| #include <asm/io.h> |
| #include <asm/irq.h> |
| |
| #include <mach/at32ap700x.h> |
| #include <mach/board.h> |
| #include <mach/hmatrix.h> |
| #include <mach/portmux.h> |
| #include <mach/sram.h> |
| |
| #include <sound/atmel-abdac.h> |
| #include <sound/atmel-ac97c.h> |
| |
| #include <video/atmel_lcdc.h> |
| |
| #include "clock.h" |
| #include "pio.h" |
| #include "pm.h" |
| |
| |
| #define PBMEM(base) \ |
| { \ |
| .start = base, \ |
| .end = base + 0x3ff, \ |
| .flags = IORESOURCE_MEM, \ |
| } |
| #define IRQ(num) \ |
| { \ |
| .start = num, \ |
| .end = num, \ |
| .flags = IORESOURCE_IRQ, \ |
| } |
| #define NAMED_IRQ(num, _name) \ |
| { \ |
| .start = num, \ |
| .end = num, \ |
| .name = _name, \ |
| .flags = IORESOURCE_IRQ, \ |
| } |
| |
| /* REVISIT these assume *every* device supports DMA, but several |
| * don't ... tc, smc, pio, rtc, watchdog, pwm, ps2, and more. |
| */ |
| #define DEFINE_DEV(_name, _id) \ |
| static u64 _name##_id##_dma_mask = DMA_BIT_MASK(32); \ |
| static struct platform_device _name##_id##_device = { \ |
| .name = #_name, \ |
| .id = _id, \ |
| .dev = { \ |
| .dma_mask = &_name##_id##_dma_mask, \ |
| .coherent_dma_mask = DMA_BIT_MASK(32), \ |
| }, \ |
| .resource = _name##_id##_resource, \ |
| .num_resources = ARRAY_SIZE(_name##_id##_resource), \ |
| } |
| #define DEFINE_DEV_DATA(_name, _id) \ |
| static u64 _name##_id##_dma_mask = DMA_BIT_MASK(32); \ |
| static struct platform_device _name##_id##_device = { \ |
| .name = #_name, \ |
| .id = _id, \ |
| .dev = { \ |
| .dma_mask = &_name##_id##_dma_mask, \ |
| .platform_data = &_name##_id##_data, \ |
| .coherent_dma_mask = DMA_BIT_MASK(32), \ |
| }, \ |
| .resource = _name##_id##_resource, \ |
| .num_resources = ARRAY_SIZE(_name##_id##_resource), \ |
| } |
| |
| #define select_peripheral(port, pin_mask, periph, flags) \ |
| at32_select_periph(GPIO_##port##_BASE, pin_mask, \ |
| GPIO_##periph, flags) |
| |
| #define DEV_CLK(_name, devname, bus, _index) \ |
| static struct clk devname##_##_name = { \ |
| .name = #_name, \ |
| .dev = &devname##_device.dev, \ |
| .parent = &bus##_clk, \ |
| .mode = bus##_clk_mode, \ |
| .get_rate = bus##_clk_get_rate, \ |
| .index = _index, \ |
| } |
| |
| static DEFINE_SPINLOCK(pm_lock); |
| |
| static struct clk osc0; |
| static struct clk osc1; |
| |
| static unsigned long osc_get_rate(struct clk *clk) |
| { |
| return at32_board_osc_rates[clk->index]; |
| } |
| |
| static unsigned long pll_get_rate(struct clk *clk, unsigned long control) |
| { |
| unsigned long div, mul, rate; |
| |
| div = PM_BFEXT(PLLDIV, control) + 1; |
| mul = PM_BFEXT(PLLMUL, control) + 1; |
| |
| rate = clk->parent->get_rate(clk->parent); |
| rate = (rate + div / 2) / div; |
| rate *= mul; |
| |
| return rate; |
| } |
| |
| static long pll_set_rate(struct clk *clk, unsigned long rate, |
| u32 *pll_ctrl) |
| { |
| unsigned long mul; |
| unsigned long mul_best_fit = 0; |
| unsigned long div; |
| unsigned long div_min; |
| unsigned long div_max; |
| unsigned long div_best_fit = 0; |
| unsigned long base; |
| unsigned long pll_in; |
| unsigned long actual = 0; |
| unsigned long rate_error; |
| unsigned long rate_error_prev = ~0UL; |
| u32 ctrl; |
| |
| /* Rate must be between 80 MHz and 200 Mhz. */ |
| if (rate < 80000000UL || rate > 200000000UL) |
| return -EINVAL; |
| |
| ctrl = PM_BF(PLLOPT, 4); |
| base = clk->parent->get_rate(clk->parent); |
| |
| /* PLL input frequency must be between 6 MHz and 32 MHz. */ |
| div_min = DIV_ROUND_UP(base, 32000000UL); |
| div_max = base / 6000000UL; |
| |
| if (div_max < div_min) |
| return -EINVAL; |
| |
| for (div = div_min; div <= div_max; div++) { |
| pll_in = (base + div / 2) / div; |
| mul = (rate + pll_in / 2) / pll_in; |
| |
| if (mul == 0) |
| continue; |
| |
| actual = pll_in * mul; |
| rate_error = abs(actual - rate); |
| |
| if (rate_error < rate_error_prev) { |
| mul_best_fit = mul; |
| div_best_fit = div; |
| rate_error_prev = rate_error; |
| } |
| |
| if (rate_error == 0) |
| break; |
| } |
| |
| if (div_best_fit == 0) |
| return -EINVAL; |
| |
| ctrl |= PM_BF(PLLMUL, mul_best_fit - 1); |
| ctrl |= PM_BF(PLLDIV, div_best_fit - 1); |
| ctrl |= PM_BF(PLLCOUNT, 16); |
| |
| if (clk->parent == &osc1) |
| ctrl |= PM_BIT(PLLOSC); |
| |
| *pll_ctrl = ctrl; |
| |
| return actual; |
| } |
| |
| static unsigned long pll0_get_rate(struct clk *clk) |
| { |
| u32 control; |
| |
| control = pm_readl(PLL0); |
| |
| return pll_get_rate(clk, control); |
| } |
| |
| static void pll1_mode(struct clk *clk, int enabled) |
| { |
| unsigned long timeout; |
| u32 status; |
| u32 ctrl; |
| |
| ctrl = pm_readl(PLL1); |
| |
| if (enabled) { |
| if (!PM_BFEXT(PLLMUL, ctrl) && !PM_BFEXT(PLLDIV, ctrl)) { |
| pr_debug("clk %s: failed to enable, rate not set\n", |
| clk->name); |
| return; |
| } |
| |
| ctrl |= PM_BIT(PLLEN); |
| pm_writel(PLL1, ctrl); |
| |
| /* Wait for PLL lock. */ |
| for (timeout = 10000; timeout; timeout--) { |
| status = pm_readl(ISR); |
| if (status & PM_BIT(LOCK1)) |
| break; |
| udelay(10); |
| } |
| |
| if (!(status & PM_BIT(LOCK1))) |
| printk(KERN_ERR "clk %s: timeout waiting for lock\n", |
| clk->name); |
| } else { |
| ctrl &= ~PM_BIT(PLLEN); |
| pm_writel(PLL1, ctrl); |
| } |
| } |
| |
| static unsigned long pll1_get_rate(struct clk *clk) |
| { |
| u32 control; |
| |
| control = pm_readl(PLL1); |
| |
| return pll_get_rate(clk, control); |
| } |
| |
| static long pll1_set_rate(struct clk *clk, unsigned long rate, int apply) |
| { |
| u32 ctrl = 0; |
| unsigned long actual_rate; |
| |
| actual_rate = pll_set_rate(clk, rate, &ctrl); |
| |
| if (apply) { |
| if (actual_rate != rate) |
| return -EINVAL; |
| if (clk->users > 0) |
| return -EBUSY; |
| pr_debug(KERN_INFO "clk %s: new rate %lu (actual rate %lu)\n", |
| clk->name, rate, actual_rate); |
| pm_writel(PLL1, ctrl); |
| } |
| |
| return actual_rate; |
| } |
| |
| static int pll1_set_parent(struct clk *clk, struct clk *parent) |
| { |
| u32 ctrl; |
| |
| if (clk->users > 0) |
| return -EBUSY; |
| |
| ctrl = pm_readl(PLL1); |
| WARN_ON(ctrl & PM_BIT(PLLEN)); |
| |
| if (parent == &osc0) |
| ctrl &= ~PM_BIT(PLLOSC); |
| else if (parent == &osc1) |
| ctrl |= PM_BIT(PLLOSC); |
| else |
| return -EINVAL; |
| |
| pm_writel(PLL1, ctrl); |
| clk->parent = parent; |
| |
| return 0; |
| } |
| |
| /* |
| * The AT32AP7000 has five primary clock sources: One 32kHz |
| * oscillator, two crystal oscillators and two PLLs. |
| */ |
| static struct clk osc32k = { |
| .name = "osc32k", |
| .get_rate = osc_get_rate, |
| .users = 1, |
| .index = 0, |
| }; |
| static struct clk osc0 = { |
| .name = "osc0", |
| .get_rate = osc_get_rate, |
| .users = 1, |
| .index = 1, |
| }; |
| static struct clk osc1 = { |
| .name = "osc1", |
| .get_rate = osc_get_rate, |
| .index = 2, |
| }; |
| static struct clk pll0 = { |
| .name = "pll0", |
| .get_rate = pll0_get_rate, |
| .parent = &osc0, |
| }; |
| static struct clk pll1 = { |
| .name = "pll1", |
| .mode = pll1_mode, |
| .get_rate = pll1_get_rate, |
| .set_rate = pll1_set_rate, |
| .set_parent = pll1_set_parent, |
| .parent = &osc0, |
| }; |
| |
| /* |
| * The main clock can be either osc0 or pll0. The boot loader may |
| * have chosen one for us, so we don't really know which one until we |
| * have a look at the SM. |
| */ |
| static struct clk *main_clock; |
| |
| /* |
| * Synchronous clocks are generated from the main clock. The clocks |
| * must satisfy the constraint |
| * fCPU >= fHSB >= fPB |
| * i.e. each clock must not be faster than its parent. |
| */ |
| static unsigned long bus_clk_get_rate(struct clk *clk, unsigned int shift) |
| { |
| return main_clock->get_rate(main_clock) >> shift; |
| }; |
| |
| static void cpu_clk_mode(struct clk *clk, int enabled) |
| { |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&pm_lock, flags); |
| mask = pm_readl(CPU_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| pm_writel(CPU_MASK, mask); |
| spin_unlock_irqrestore(&pm_lock, flags); |
| } |
| |
| static unsigned long cpu_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = pm_readl(CKSEL); |
| if (cksel & PM_BIT(CPUDIV)) |
| shift = PM_BFEXT(CPUSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static long cpu_clk_set_rate(struct clk *clk, unsigned long rate, int apply) |
| { |
| u32 control; |
| unsigned long parent_rate, child_div, actual_rate, div; |
| |
| parent_rate = clk->parent->get_rate(clk->parent); |
| control = pm_readl(CKSEL); |
| |
| if (control & PM_BIT(HSBDIV)) |
| child_div = 1 << (PM_BFEXT(HSBSEL, control) + 1); |
| else |
| child_div = 1; |
| |
| if (rate > 3 * (parent_rate / 4) || child_div == 1) { |
| actual_rate = parent_rate; |
| control &= ~PM_BIT(CPUDIV); |
| } else { |
| unsigned int cpusel; |
| div = (parent_rate + rate / 2) / rate; |
| if (div > child_div) |
| div = child_div; |
| cpusel = (div > 1) ? (fls(div) - 2) : 0; |
| control = PM_BIT(CPUDIV) | PM_BFINS(CPUSEL, cpusel, control); |
| actual_rate = parent_rate / (1 << (cpusel + 1)); |
| } |
| |
| pr_debug("clk %s: new rate %lu (actual rate %lu)\n", |
| clk->name, rate, actual_rate); |
| |
| if (apply) |
| pm_writel(CKSEL, control); |
| |
| return actual_rate; |
| } |
| |
| static void hsb_clk_mode(struct clk *clk, int enabled) |
| { |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&pm_lock, flags); |
| mask = pm_readl(HSB_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| pm_writel(HSB_MASK, mask); |
| spin_unlock_irqrestore(&pm_lock, flags); |
| } |
| |
| static unsigned long hsb_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = pm_readl(CKSEL); |
| if (cksel & PM_BIT(HSBDIV)) |
| shift = PM_BFEXT(HSBSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| void pba_clk_mode(struct clk *clk, int enabled) |
| { |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&pm_lock, flags); |
| mask = pm_readl(PBA_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| pm_writel(PBA_MASK, mask); |
| spin_unlock_irqrestore(&pm_lock, flags); |
| } |
| |
| unsigned long pba_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = pm_readl(CKSEL); |
| if (cksel & PM_BIT(PBADIV)) |
| shift = PM_BFEXT(PBASEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static void pbb_clk_mode(struct clk *clk, int enabled) |
| { |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&pm_lock, flags); |
| mask = pm_readl(PBB_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| pm_writel(PBB_MASK, mask); |
| spin_unlock_irqrestore(&pm_lock, flags); |
| } |
| |
| static unsigned long pbb_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = pm_readl(CKSEL); |
| if (cksel & PM_BIT(PBBDIV)) |
| shift = PM_BFEXT(PBBSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static struct clk cpu_clk = { |
| .name = "cpu", |
| .get_rate = cpu_clk_get_rate, |
| .set_rate = cpu_clk_set_rate, |
| .users = 1, |
| }; |
| static struct clk hsb_clk = { |
| .name = "hsb", |
| .parent = &cpu_clk, |
| .get_rate = hsb_clk_get_rate, |
| }; |
| static struct clk pba_clk = { |
| .name = "pba", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = pba_clk_get_rate, |
| .index = 1, |
| }; |
| static struct clk pbb_clk = { |
| .name = "pbb", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .users = 1, |
| .index = 2, |
| }; |
| |
| /* -------------------------------------------------------------------- |
| * Generic Clock operations |
| * -------------------------------------------------------------------- */ |
| |
| static void genclk_mode(struct clk *clk, int enabled) |
| { |
| u32 control; |
| |
| control = pm_readl(GCCTRL(clk->index)); |
| if (enabled) |
| control |= PM_BIT(CEN); |
| else |
| control &= ~PM_BIT(CEN); |
| pm_writel(GCCTRL(clk->index), control); |
| } |
| |
| static unsigned long genclk_get_rate(struct clk *clk) |
| { |
| u32 control; |
| unsigned long div = 1; |
| |
| control = pm_readl(GCCTRL(clk->index)); |
| if (control & PM_BIT(DIVEN)) |
| div = 2 * (PM_BFEXT(DIV, control) + 1); |
| |
| return clk->parent->get_rate(clk->parent) / div; |
| } |
| |
| static long genclk_set_rate(struct clk *clk, unsigned long rate, int apply) |
| { |
| u32 control; |
| unsigned long parent_rate, actual_rate, div; |
| |
| parent_rate = clk->parent->get_rate(clk->parent); |
| control = pm_readl(GCCTRL(clk->index)); |
| |
| if (rate > 3 * parent_rate / 4) { |
| actual_rate = parent_rate; |
| control &= ~PM_BIT(DIVEN); |
| } else { |
| div = (parent_rate + rate) / (2 * rate) - 1; |
| control = PM_BFINS(DIV, div, control) | PM_BIT(DIVEN); |
| actual_rate = parent_rate / (2 * (div + 1)); |
| } |
| |
| dev_dbg(clk->dev, "clk %s: new rate %lu (actual rate %lu)\n", |
| clk->name, rate, actual_rate); |
| |
| if (apply) |
| pm_writel(GCCTRL(clk->index), control); |
| |
| return actual_rate; |
| } |
| |
| int genclk_set_parent(struct clk *clk, struct clk *parent) |
| { |
| u32 control; |
| |
| dev_dbg(clk->dev, "clk %s: new parent %s (was %s)\n", |
| clk->name, parent->name, clk->parent->name); |
| |
| control = pm_readl(GCCTRL(clk->index)); |
| |
| if (parent == &osc1 || parent == &pll1) |
| control |= PM_BIT(OSCSEL); |
| else if (parent == &osc0 || parent == &pll0) |
| control &= ~PM_BIT(OSCSEL); |
| else |
| return -EINVAL; |
| |
| if (parent == &pll0 || parent == &pll1) |
| control |= PM_BIT(PLLSEL); |
| else |
| control &= ~PM_BIT(PLLSEL); |
| |
| pm_writel(GCCTRL(clk->index), control); |
| clk->parent = parent; |
| |
| return 0; |
| } |
| |
| static void __init genclk_init_parent(struct clk *clk) |
| { |
| u32 control; |
| struct clk *parent; |
| |
| BUG_ON(clk->index > 7); |
| |
| control = pm_readl(GCCTRL(clk->index)); |
| if (control & PM_BIT(OSCSEL)) |
| parent = (control & PM_BIT(PLLSEL)) ? &pll1 : &osc1; |
| else |
| parent = (control & PM_BIT(PLLSEL)) ? &pll0 : &osc0; |
| |
| clk->parent = parent; |
| } |
| |
| static struct dw_dma_platform_data dw_dmac0_data = { |
| .nr_channels = 3, |
| .block_size = 4095U, |
| .nr_masters = 2, |
| .data_width = { 2, 2, 0, 0 }, |
| }; |
| |
| static struct resource dw_dmac0_resource[] = { |
| PBMEM(0xff200000), |
| IRQ(2), |
| }; |
| DEFINE_DEV_DATA(dw_dmac, 0); |
| DEV_CLK(hclk, dw_dmac0, hsb, 10); |
| |
| /* -------------------------------------------------------------------- |
| * System peripherals |
| * -------------------------------------------------------------------- */ |
| static struct resource at32_pm0_resource[] = { |
| { |
| .start = 0xfff00000, |
| .end = 0xfff0007f, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(20), |
| }; |
| |
| static struct resource at32ap700x_rtc0_resource[] = { |
| { |
| .start = 0xfff00080, |
| .end = 0xfff000af, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(21), |
| }; |
| |
| static struct resource at32_wdt0_resource[] = { |
| { |
| .start = 0xfff000b0, |
| .end = 0xfff000cf, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| static struct resource at32_eic0_resource[] = { |
| { |
| .start = 0xfff00100, |
| .end = 0xfff0013f, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(19), |
| }; |
| |
| DEFINE_DEV(at32_pm, 0); |
| DEFINE_DEV(at32ap700x_rtc, 0); |
| DEFINE_DEV(at32_wdt, 0); |
| DEFINE_DEV(at32_eic, 0); |
| |
| /* |
| * Peripheral clock for PM, RTC, WDT and EIC. PM will ensure that this |
| * is always running. |
| */ |
| static struct clk at32_pm_pclk = { |
| .name = "pclk", |
| .dev = &at32_pm0_device.dev, |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .users = 1, |
| .index = 0, |
| }; |
| |
| static struct resource intc0_resource[] = { |
| PBMEM(0xfff00400), |
| }; |
| struct platform_device at32_intc0_device = { |
| .name = "intc", |
| .id = 0, |
| .resource = intc0_resource, |
| .num_resources = ARRAY_SIZE(intc0_resource), |
| }; |
| DEV_CLK(pclk, at32_intc0, pbb, 1); |
| |
| static struct clk ebi_clk = { |
| .name = "ebi", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = hsb_clk_get_rate, |
| .users = 1, |
| }; |
| static struct clk hramc_clk = { |
| .name = "hramc", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = hsb_clk_get_rate, |
| .users = 1, |
| .index = 3, |
| }; |
| static struct clk sdramc_clk = { |
| .name = "sdramc_clk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .users = 1, |
| .index = 14, |
| }; |
| |
| static struct resource smc0_resource[] = { |
| PBMEM(0xfff03400), |
| }; |
| DEFINE_DEV(smc, 0); |
| DEV_CLK(pclk, smc0, pbb, 13); |
| DEV_CLK(mck, smc0, hsb, 0); |
| |
| static struct platform_device pdc_device = { |
| .name = "pdc", |
| .id = 0, |
| }; |
| DEV_CLK(hclk, pdc, hsb, 4); |
| DEV_CLK(pclk, pdc, pba, 16); |
| |
| static struct clk pico_clk = { |
| .name = "pico", |
| .parent = &cpu_clk, |
| .mode = cpu_clk_mode, |
| .get_rate = cpu_clk_get_rate, |
| .users = 1, |
| }; |
| |
| /* -------------------------------------------------------------------- |
| * HMATRIX |
| * -------------------------------------------------------------------- */ |
| |
| struct clk at32_hmatrix_clk = { |
| .name = "hmatrix_clk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 2, |
| .users = 1, |
| }; |
| |
| /* |
| * Set bits in the HMATRIX Special Function Register (SFR) used by the |
| * External Bus Interface (EBI). This can be used to enable special |
| * features like CompactFlash support, NAND Flash support, etc. on |
| * certain chipselects. |
| */ |
| static inline void set_ebi_sfr_bits(u32 mask) |
| { |
| hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, mask); |
| } |
| |
| /* -------------------------------------------------------------------- |
| * Timer/Counter (TC) |
| * -------------------------------------------------------------------- */ |
| |
| static struct resource at32_tcb0_resource[] = { |
| PBMEM(0xfff00c00), |
| IRQ(22), |
| }; |
| static struct platform_device at32_tcb0_device = { |
| .name = "atmel_tcb", |
| .id = 0, |
| .resource = at32_tcb0_resource, |
| .num_resources = ARRAY_SIZE(at32_tcb0_resource), |
| }; |
| DEV_CLK(t0_clk, at32_tcb0, pbb, 3); |
| |
| static struct resource at32_tcb1_resource[] = { |
| PBMEM(0xfff01000), |
| IRQ(23), |
| }; |
| static struct platform_device at32_tcb1_device = { |
| .name = "atmel_tcb", |
| .id = 1, |
| .resource = at32_tcb1_resource, |
| .num_resources = ARRAY_SIZE(at32_tcb1_resource), |
| }; |
| DEV_CLK(t0_clk, at32_tcb1, pbb, 4); |
| |
| /* -------------------------------------------------------------------- |
| * PIO |
| * -------------------------------------------------------------------- */ |
| |
| static struct resource pio0_resource[] = { |
| PBMEM(0xffe02800), |
| IRQ(13), |
| }; |
| DEFINE_DEV(pio, 0); |
| DEV_CLK(mck, pio0, pba, 10); |
| |
| static struct resource pio1_resource[] = { |
| PBMEM(0xffe02c00), |
| IRQ(14), |
| }; |
| DEFINE_DEV(pio, 1); |
| DEV_CLK(mck, pio1, pba, 11); |
| |
| static struct resource pio2_resource[] = { |
| PBMEM(0xffe03000), |
| IRQ(15), |
| }; |
| DEFINE_DEV(pio, 2); |
| DEV_CLK(mck, pio2, pba, 12); |
| |
| static struct resource pio3_resource[] = { |
| PBMEM(0xffe03400), |
| IRQ(16), |
| }; |
| DEFINE_DEV(pio, 3); |
| DEV_CLK(mck, pio3, pba, 13); |
| |
| static struct resource pio4_resource[] = { |
| PBMEM(0xffe03800), |
| IRQ(17), |
| }; |
| DEFINE_DEV(pio, 4); |
| DEV_CLK(mck, pio4, pba, 14); |
| |
| static int __init system_device_init(void) |
| { |
| platform_device_register(&at32_pm0_device); |
| platform_device_register(&at32_intc0_device); |
| platform_device_register(&at32ap700x_rtc0_device); |
| platform_device_register(&at32_wdt0_device); |
| platform_device_register(&at32_eic0_device); |
| platform_device_register(&smc0_device); |
| platform_device_register(&pdc_device); |
| platform_device_register(&dw_dmac0_device); |
| |
| platform_device_register(&at32_tcb0_device); |
| platform_device_register(&at32_tcb1_device); |
| |
| platform_device_register(&pio0_device); |
| platform_device_register(&pio1_device); |
| platform_device_register(&pio2_device); |
| platform_device_register(&pio3_device); |
| platform_device_register(&pio4_device); |
| |
| return 0; |
| } |
| core_initcall(system_device_init); |
| |
| /* -------------------------------------------------------------------- |
| * PSIF |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_psif0_resource[] __initdata = { |
| { |
| .start = 0xffe03c00, |
| .end = 0xffe03cff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(18), |
| }; |
| static struct clk atmel_psif0_pclk = { |
| .name = "pclk", |
| .parent = &pba_clk, |
| .mode = pba_clk_mode, |
| .get_rate = pba_clk_get_rate, |
| .index = 15, |
| }; |
| |
| static struct resource atmel_psif1_resource[] __initdata = { |
| { |
| .start = 0xffe03d00, |
| .end = 0xffe03dff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(18), |
| }; |
| static struct clk atmel_psif1_pclk = { |
| .name = "pclk", |
| .parent = &pba_clk, |
| .mode = pba_clk_mode, |
| .get_rate = pba_clk_get_rate, |
| .index = 15, |
| }; |
| |
| struct platform_device *__init at32_add_device_psif(unsigned int id) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask; |
| |
| if (!(id == 0 || id == 1)) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_psif", id); |
| if (!pdev) |
| return NULL; |
| |
| switch (id) { |
| case 0: |
| pin_mask = (1 << 8) | (1 << 9); /* CLOCK & DATA */ |
| |
| if (platform_device_add_resources(pdev, atmel_psif0_resource, |
| ARRAY_SIZE(atmel_psif0_resource))) |
| goto err_add_resources; |
| atmel_psif0_pclk.dev = &pdev->dev; |
| select_peripheral(PIOA, pin_mask, PERIPH_A, 0); |
| break; |
| case 1: |
| pin_mask = (1 << 11) | (1 << 12); /* CLOCK & DATA */ |
| |
| if (platform_device_add_resources(pdev, atmel_psif1_resource, |
| ARRAY_SIZE(atmel_psif1_resource))) |
| goto err_add_resources; |
| atmel_psif1_pclk.dev = &pdev->dev; |
| select_peripheral(PIOB, pin_mask, PERIPH_A, 0); |
| break; |
| default: |
| return NULL; |
| } |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| err_add_resources: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * USART |
| * -------------------------------------------------------------------- */ |
| |
| static struct atmel_uart_data atmel_usart0_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart0_resource[] = { |
| PBMEM(0xffe00c00), |
| IRQ(6), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 0); |
| DEV_CLK(usart, atmel_usart0, pba, 3); |
| |
| static struct atmel_uart_data atmel_usart1_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart1_resource[] = { |
| PBMEM(0xffe01000), |
| IRQ(7), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 1); |
| DEV_CLK(usart, atmel_usart1, pba, 4); |
| |
| static struct atmel_uart_data atmel_usart2_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart2_resource[] = { |
| PBMEM(0xffe01400), |
| IRQ(8), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 2); |
| DEV_CLK(usart, atmel_usart2, pba, 5); |
| |
| static struct atmel_uart_data atmel_usart3_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart3_resource[] = { |
| PBMEM(0xffe01800), |
| IRQ(9), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 3); |
| DEV_CLK(usart, atmel_usart3, pba, 6); |
| |
| static inline void configure_usart0_pins(int flags) |
| { |
| u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */ |
| if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 6); |
| if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 7); |
| if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 10); |
| |
| select_peripheral(PIOA, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); |
| } |
| |
| static inline void configure_usart1_pins(int flags) |
| { |
| u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */ |
| if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 19); |
| if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 20); |
| if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 16); |
| |
| select_peripheral(PIOA, pin_mask, PERIPH_A, AT32_GPIOF_PULLUP); |
| } |
| |
| static inline void configure_usart2_pins(int flags) |
| { |
| u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */ |
| if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 30); |
| if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 29); |
| if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 28); |
| |
| select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); |
| } |
| |
| static inline void configure_usart3_pins(int flags) |
| { |
| u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */ |
| if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 16); |
| if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 15); |
| if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 19); |
| |
| select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); |
| } |
| |
| static struct platform_device *__initdata at32_usarts[4]; |
| |
| void __init at32_map_usart(unsigned int hw_id, unsigned int line, int flags) |
| { |
| struct platform_device *pdev; |
| struct atmel_uart_data *pdata; |
| |
| switch (hw_id) { |
| case 0: |
| pdev = &atmel_usart0_device; |
| configure_usart0_pins(flags); |
| break; |
| case 1: |
| pdev = &atmel_usart1_device; |
| configure_usart1_pins(flags); |
| break; |
| case 2: |
| pdev = &atmel_usart2_device; |
| configure_usart2_pins(flags); |
| break; |
| case 3: |
| pdev = &atmel_usart3_device; |
| configure_usart3_pins(flags); |
| break; |
| default: |
| return; |
| } |
| |
| if (PXSEG(pdev->resource[0].start) == P4SEG) { |
| /* Addresses in the P4 segment are permanently mapped 1:1 */ |
| struct atmel_uart_data *data = pdev->dev.platform_data; |
| data->regs = (void __iomem *)pdev->resource[0].start; |
| } |
| |
| pdev->id = line; |
| pdata = pdev->dev.platform_data; |
| pdata->num = line; |
| at32_usarts[line] = pdev; |
| } |
| |
| struct platform_device *__init at32_add_device_usart(unsigned int id) |
| { |
| platform_device_register(at32_usarts[id]); |
| return at32_usarts[id]; |
| } |
| |
| void __init at32_setup_serial_console(unsigned int usart_id) |
| { |
| atmel_default_console_device = at32_usarts[usart_id]; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * Ethernet |
| * -------------------------------------------------------------------- */ |
| |
| #ifdef CONFIG_CPU_AT32AP7000 |
| static struct macb_platform_data macb0_data; |
| static struct resource macb0_resource[] = { |
| PBMEM(0xfff01800), |
| IRQ(25), |
| }; |
| DEFINE_DEV_DATA(macb, 0); |
| DEV_CLK(hclk, macb0, hsb, 8); |
| DEV_CLK(pclk, macb0, pbb, 6); |
| |
| static struct macb_platform_data macb1_data; |
| static struct resource macb1_resource[] = { |
| PBMEM(0xfff01c00), |
| IRQ(26), |
| }; |
| DEFINE_DEV_DATA(macb, 1); |
| DEV_CLK(hclk, macb1, hsb, 9); |
| DEV_CLK(pclk, macb1, pbb, 7); |
| |
| struct platform_device *__init |
| at32_add_device_eth(unsigned int id, struct macb_platform_data *data) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask; |
| |
| switch (id) { |
| case 0: |
| pdev = &macb0_device; |
| |
| pin_mask = (1 << 3); /* TXD0 */ |
| pin_mask |= (1 << 4); /* TXD1 */ |
| pin_mask |= (1 << 7); /* TXEN */ |
| pin_mask |= (1 << 8); /* TXCK */ |
| pin_mask |= (1 << 9); /* RXD0 */ |
| pin_mask |= (1 << 10); /* RXD1 */ |
| pin_mask |= (1 << 13); /* RXER */ |
| pin_mask |= (1 << 15); /* RXDV */ |
| pin_mask |= (1 << 16); /* MDC */ |
| pin_mask |= (1 << 17); /* MDIO */ |
| |
| if (!data->is_rmii) { |
| pin_mask |= (1 << 0); /* COL */ |
| pin_mask |= (1 << 1); /* CRS */ |
| pin_mask |= (1 << 2); /* TXER */ |
| pin_mask |= (1 << 5); /* TXD2 */ |
| pin_mask |= (1 << 6); /* TXD3 */ |
| pin_mask |= (1 << 11); /* RXD2 */ |
| pin_mask |= (1 << 12); /* RXD3 */ |
| pin_mask |= (1 << 14); /* RXCK */ |
| #ifndef CONFIG_BOARD_MIMC200 |
| pin_mask |= (1 << 18); /* SPD */ |
| #endif |
| } |
| |
| select_peripheral(PIOC, pin_mask, PERIPH_A, 0); |
| |
| break; |
| |
| case 1: |
| pdev = &macb1_device; |
| |
| pin_mask = (1 << 13); /* TXD0 */ |
| pin_mask |= (1 << 14); /* TXD1 */ |
| pin_mask |= (1 << 11); /* TXEN */ |
| pin_mask |= (1 << 12); /* TXCK */ |
| pin_mask |= (1 << 10); /* RXD0 */ |
| pin_mask |= (1 << 6); /* RXD1 */ |
| pin_mask |= (1 << 5); /* RXER */ |
| pin_mask |= (1 << 4); /* RXDV */ |
| pin_mask |= (1 << 3); /* MDC */ |
| pin_mask |= (1 << 2); /* MDIO */ |
| |
| #ifndef CONFIG_BOARD_MIMC200 |
| if (!data->is_rmii) |
| pin_mask |= (1 << 15); /* SPD */ |
| #endif |
| |
| select_peripheral(PIOD, pin_mask, PERIPH_B, 0); |
| |
| if (!data->is_rmii) { |
| pin_mask = (1 << 19); /* COL */ |
| pin_mask |= (1 << 23); /* CRS */ |
| pin_mask |= (1 << 26); /* TXER */ |
| pin_mask |= (1 << 27); /* TXD2 */ |
| pin_mask |= (1 << 28); /* TXD3 */ |
| pin_mask |= (1 << 29); /* RXD2 */ |
| pin_mask |= (1 << 30); /* RXD3 */ |
| pin_mask |= (1 << 24); /* RXCK */ |
| |
| select_peripheral(PIOC, pin_mask, PERIPH_B, 0); |
| } |
| break; |
| |
| default: |
| return NULL; |
| } |
| |
| memcpy(pdev->dev.platform_data, data, sizeof(struct macb_platform_data)); |
| platform_device_register(pdev); |
| |
| return pdev; |
| } |
| #endif |
| |
| /* -------------------------------------------------------------------- |
| * SPI |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_spi0_resource[] = { |
| PBMEM(0xffe00000), |
| IRQ(3), |
| }; |
| DEFINE_DEV(atmel_spi, 0); |
| DEV_CLK(spi_clk, atmel_spi0, pba, 0); |
| |
| static struct resource atmel_spi1_resource[] = { |
| PBMEM(0xffe00400), |
| IRQ(4), |
| }; |
| DEFINE_DEV(atmel_spi, 1); |
| DEV_CLK(spi_clk, atmel_spi1, pba, 1); |
| |
| void __init |
| at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n) |
| { |
| /* |
| * Manage the chipselects as GPIOs, normally using the same pins |
| * the SPI controller expects; but boards can use other pins. |
| */ |
| static u8 __initdata spi_pins[][4] = { |
| { GPIO_PIN_PA(3), GPIO_PIN_PA(4), |
| GPIO_PIN_PA(5), GPIO_PIN_PA(20) }, |
| { GPIO_PIN_PB(2), GPIO_PIN_PB(3), |
| GPIO_PIN_PB(4), GPIO_PIN_PA(27) }, |
| }; |
| unsigned int pin, mode; |
| |
| /* There are only 2 SPI controllers */ |
| if (bus_num > 1) |
| return; |
| |
| for (; n; n--, b++) { |
| b->bus_num = bus_num; |
| if (b->chip_select >= 4) |
| continue; |
| pin = (unsigned)b->controller_data; |
| if (!pin) { |
| pin = spi_pins[bus_num][b->chip_select]; |
| b->controller_data = (void *)pin; |
| } |
| mode = AT32_GPIOF_OUTPUT; |
| if (!(b->mode & SPI_CS_HIGH)) |
| mode |= AT32_GPIOF_HIGH; |
| at32_select_gpio(pin, mode); |
| } |
| } |
| |
| struct platform_device *__init |
| at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask; |
| |
| switch (id) { |
| case 0: |
| pdev = &atmel_spi0_device; |
| pin_mask = (1 << 1) | (1 << 2); /* MOSI & SCK */ |
| |
| /* pullup MISO so a level is always defined */ |
| select_peripheral(PIOA, (1 << 0), PERIPH_A, AT32_GPIOF_PULLUP); |
| select_peripheral(PIOA, pin_mask, PERIPH_A, 0); |
| |
| at32_spi_setup_slaves(0, b, n); |
| break; |
| |
| case 1: |
| pdev = &atmel_spi1_device; |
| pin_mask = (1 << 1) | (1 << 5); /* MOSI */ |
| |
| /* pullup MISO so a level is always defined */ |
| select_peripheral(PIOB, (1 << 0), PERIPH_B, AT32_GPIOF_PULLUP); |
| select_peripheral(PIOB, pin_mask, PERIPH_B, 0); |
| |
| at32_spi_setup_slaves(1, b, n); |
| break; |
| |
| default: |
| return NULL; |
| } |
| |
| spi_register_board_info(b, n); |
| platform_device_register(pdev); |
| return pdev; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * TWI |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_twi0_resource[] __initdata = { |
| PBMEM(0xffe00800), |
| IRQ(5), |
| }; |
| static struct clk atmel_twi0_pclk = { |
| .name = "twi_pclk", |
| .parent = &pba_clk, |
| .mode = pba_clk_mode, |
| .get_rate = pba_clk_get_rate, |
| .index = 2, |
| }; |
| |
| struct platform_device *__init at32_add_device_twi(unsigned int id, |
| struct i2c_board_info *b, |
| unsigned int n) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask; |
| |
| if (id != 0) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_twi", id); |
| if (!pdev) |
| return NULL; |
| |
| if (platform_device_add_resources(pdev, atmel_twi0_resource, |
| ARRAY_SIZE(atmel_twi0_resource))) |
| goto err_add_resources; |
| |
| pin_mask = (1 << 6) | (1 << 7); /* SDA & SDL */ |
| |
| select_peripheral(PIOA, pin_mask, PERIPH_A, 0); |
| |
| atmel_twi0_pclk.dev = &pdev->dev; |
| |
| if (b) |
| i2c_register_board_info(id, b, n); |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| err_add_resources: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * MMC |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_mci0_resource[] __initdata = { |
| PBMEM(0xfff02400), |
| IRQ(28), |
| }; |
| static struct clk atmel_mci0_pclk = { |
| .name = "mci_clk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 9, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_mci(unsigned int id, struct mci_platform_data *data) |
| { |
| struct platform_device *pdev; |
| struct mci_dma_data *slave; |
| u32 pioa_mask; |
| u32 piob_mask; |
| |
| if (id != 0 || !data) |
| return NULL; |
| |
| /* Must have at least one usable slot */ |
| if (!data->slot[0].bus_width && !data->slot[1].bus_width) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_mci", id); |
| if (!pdev) |
| goto fail; |
| |
| if (platform_device_add_resources(pdev, atmel_mci0_resource, |
| ARRAY_SIZE(atmel_mci0_resource))) |
| goto fail; |
| |
| slave = kzalloc(sizeof(struct mci_dma_data), GFP_KERNEL); |
| if (!slave) |
| goto fail; |
| |
| slave->sdata.dma_dev = &dw_dmac0_device.dev; |
| slave->sdata.cfg_hi = (DWC_CFGH_SRC_PER(0) |
| | DWC_CFGH_DST_PER(1)); |
| slave->sdata.cfg_lo &= ~(DWC_CFGL_HS_DST_POL |
| | DWC_CFGL_HS_SRC_POL); |
| |
| data->dma_slave = slave; |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct mci_platform_data))) |
| goto fail_free; |
| |
| /* CLK line is common to both slots */ |
| pioa_mask = 1 << 10; |
| |
| switch (data->slot[0].bus_width) { |
| case 4: |
| pioa_mask |= 1 << 13; /* DATA1 */ |
| pioa_mask |= 1 << 14; /* DATA2 */ |
| pioa_mask |= 1 << 15; /* DATA3 */ |
| /* fall through */ |
| case 1: |
| pioa_mask |= 1 << 11; /* CMD */ |
| pioa_mask |= 1 << 12; /* DATA0 */ |
| |
| if (gpio_is_valid(data->slot[0].detect_pin)) |
| at32_select_gpio(data->slot[0].detect_pin, 0); |
| if (gpio_is_valid(data->slot[0].wp_pin)) |
| at32_select_gpio(data->slot[0].wp_pin, 0); |
| break; |
| case 0: |
| /* Slot is unused */ |
| break; |
| default: |
| goto fail_free; |
| } |
| |
| select_peripheral(PIOA, pioa_mask, PERIPH_A, 0); |
| piob_mask = 0; |
| |
| switch (data->slot[1].bus_width) { |
| case 4: |
| piob_mask |= 1 << 8; /* DATA1 */ |
| piob_mask |= 1 << 9; /* DATA2 */ |
| piob_mask |= 1 << 10; /* DATA3 */ |
| /* fall through */ |
| case 1: |
| piob_mask |= 1 << 6; /* CMD */ |
| piob_mask |= 1 << 7; /* DATA0 */ |
| select_peripheral(PIOB, piob_mask, PERIPH_B, 0); |
| |
| if (gpio_is_valid(data->slot[1].detect_pin)) |
| at32_select_gpio(data->slot[1].detect_pin, 0); |
| if (gpio_is_valid(data->slot[1].wp_pin)) |
| at32_select_gpio(data->slot[1].wp_pin, 0); |
| break; |
| case 0: |
| /* Slot is unused */ |
| break; |
| default: |
| if (!data->slot[0].bus_width) |
| goto fail_free; |
| |
| data->slot[1].bus_width = 0; |
| break; |
| } |
| |
| atmel_mci0_pclk.dev = &pdev->dev; |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| fail_free: |
| kfree(slave); |
| fail: |
| data->dma_slave = NULL; |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * LCDC |
| * -------------------------------------------------------------------- */ |
| #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002) |
| static struct atmel_lcdfb_info atmel_lcdfb0_data; |
| static struct resource atmel_lcdfb0_resource[] = { |
| { |
| .start = 0xff000000, |
| .end = 0xff000fff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(1), |
| { |
| /* Placeholder for pre-allocated fb memory */ |
| .start = 0x00000000, |
| .end = 0x00000000, |
| .flags = 0, |
| }, |
| }; |
| DEFINE_DEV_DATA(atmel_lcdfb, 0); |
| DEV_CLK(hclk, atmel_lcdfb0, hsb, 7); |
| static struct clk atmel_lcdfb0_pixclk = { |
| .name = "lcdc_clk", |
| .dev = &atmel_lcdfb0_device.dev, |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 7, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data, |
| unsigned long fbmem_start, unsigned long fbmem_len, |
| u64 pin_mask) |
| { |
| struct platform_device *pdev; |
| struct atmel_lcdfb_info *info; |
| struct fb_monspecs *monspecs; |
| struct fb_videomode *modedb; |
| unsigned int modedb_size; |
| u32 portc_mask, portd_mask, porte_mask; |
| |
| /* |
| * Do a deep copy of the fb data, monspecs and modedb. Make |
| * sure all allocations are done before setting up the |
| * portmux. |
| */ |
| monspecs = kmemdup(data->default_monspecs, |
| sizeof(struct fb_monspecs), GFP_KERNEL); |
| if (!monspecs) |
| return NULL; |
| |
| modedb_size = sizeof(struct fb_videomode) * monspecs->modedb_len; |
| modedb = kmemdup(monspecs->modedb, modedb_size, GFP_KERNEL); |
| if (!modedb) |
| goto err_dup_modedb; |
| monspecs->modedb = modedb; |
| |
| switch (id) { |
| case 0: |
| pdev = &atmel_lcdfb0_device; |
| |
| if (pin_mask == 0ULL) |
| /* Default to "full" lcdc control signals and 24bit */ |
| pin_mask = ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL; |
| |
| /* LCDC on port C */ |
| portc_mask = pin_mask & 0xfff80000; |
| select_peripheral(PIOC, portc_mask, PERIPH_A, 0); |
| |
| /* LCDC on port D */ |
| portd_mask = pin_mask & 0x0003ffff; |
| select_peripheral(PIOD, portd_mask, PERIPH_A, 0); |
| |
| /* LCDC on port E */ |
| porte_mask = (pin_mask >> 32) & 0x0007ffff; |
| select_peripheral(PIOE, porte_mask, PERIPH_B, 0); |
| |
| clk_set_parent(&atmel_lcdfb0_pixclk, &pll0); |
| clk_set_rate(&atmel_lcdfb0_pixclk, clk_get_rate(&pll0)); |
| break; |
| |
| default: |
| goto err_invalid_id; |
| } |
| |
| if (fbmem_len) { |
| pdev->resource[2].start = fbmem_start; |
| pdev->resource[2].end = fbmem_start + fbmem_len - 1; |
| pdev->resource[2].flags = IORESOURCE_MEM; |
| } |
| |
| info = pdev->dev.platform_data; |
| memcpy(info, data, sizeof(struct atmel_lcdfb_info)); |
| info->default_monspecs = monspecs; |
| |
| pdev->name = "at32ap-lcdfb"; |
| |
| platform_device_register(pdev); |
| return pdev; |
| |
| err_invalid_id: |
| kfree(modedb); |
| err_dup_modedb: |
| kfree(monspecs); |
| return NULL; |
| } |
| #endif |
| |
| /* -------------------------------------------------------------------- |
| * PWM |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_pwm0_resource[] __initdata = { |
| PBMEM(0xfff01400), |
| IRQ(24), |
| }; |
| static struct clk atmel_pwm0_mck = { |
| .name = "pwm_clk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 5, |
| }; |
| |
| struct platform_device *__init at32_add_device_pwm(u32 mask) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask; |
| |
| if (!mask) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_pwm", 0); |
| if (!pdev) |
| return NULL; |
| |
| if (platform_device_add_resources(pdev, atmel_pwm0_resource, |
| ARRAY_SIZE(atmel_pwm0_resource))) |
| goto out_free_pdev; |
| |
| if (platform_device_add_data(pdev, &mask, sizeof(mask))) |
| goto out_free_pdev; |
| |
| pin_mask = 0; |
| if (mask & (1 << 0)) |
| pin_mask |= (1 << 28); |
| if (mask & (1 << 1)) |
| pin_mask |= (1 << 29); |
| if (pin_mask > 0) |
| select_peripheral(PIOA, pin_mask, PERIPH_A, 0); |
| |
| pin_mask = 0; |
| if (mask & (1 << 2)) |
| pin_mask |= (1 << 21); |
| if (mask & (1 << 3)) |
| pin_mask |= (1 << 22); |
| if (pin_mask > 0) |
| select_peripheral(PIOA, pin_mask, PERIPH_B, 0); |
| |
| atmel_pwm0_mck.dev = &pdev->dev; |
| |
| platform_device_add(pdev); |
| |
| return pdev; |
| |
| out_free_pdev: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * SSC |
| * -------------------------------------------------------------------- */ |
| static struct resource ssc0_resource[] = { |
| PBMEM(0xffe01c00), |
| IRQ(10), |
| }; |
| DEFINE_DEV(ssc, 0); |
| DEV_CLK(pclk, ssc0, pba, 7); |
| |
| static struct resource ssc1_resource[] = { |
| PBMEM(0xffe02000), |
| IRQ(11), |
| }; |
| DEFINE_DEV(ssc, 1); |
| DEV_CLK(pclk, ssc1, pba, 8); |
| |
| static struct resource ssc2_resource[] = { |
| PBMEM(0xffe02400), |
| IRQ(12), |
| }; |
| DEFINE_DEV(ssc, 2); |
| DEV_CLK(pclk, ssc2, pba, 9); |
| |
| struct platform_device *__init |
| at32_add_device_ssc(unsigned int id, unsigned int flags) |
| { |
| struct platform_device *pdev; |
| u32 pin_mask = 0; |
| |
| switch (id) { |
| case 0: |
| pdev = &ssc0_device; |
| if (flags & ATMEL_SSC_RF) |
| pin_mask |= (1 << 21); /* RF */ |
| if (flags & ATMEL_SSC_RK) |
| pin_mask |= (1 << 22); /* RK */ |
| if (flags & ATMEL_SSC_TK) |
| pin_mask |= (1 << 23); /* TK */ |
| if (flags & ATMEL_SSC_TF) |
| pin_mask |= (1 << 24); /* TF */ |
| if (flags & ATMEL_SSC_TD) |
| pin_mask |= (1 << 25); /* TD */ |
| if (flags & ATMEL_SSC_RD) |
| pin_mask |= (1 << 26); /* RD */ |
| |
| if (pin_mask > 0) |
| select_peripheral(PIOA, pin_mask, PERIPH_A, 0); |
| |
| break; |
| case 1: |
| pdev = &ssc1_device; |
| if (flags & ATMEL_SSC_RF) |
| pin_mask |= (1 << 0); /* RF */ |
| if (flags & ATMEL_SSC_RK) |
| pin_mask |= (1 << 1); /* RK */ |
| if (flags & ATMEL_SSC_TK) |
| pin_mask |= (1 << 2); /* TK */ |
| if (flags & ATMEL_SSC_TF) |
| pin_mask |= (1 << 3); /* TF */ |
| if (flags & ATMEL_SSC_TD) |
| pin_mask |= (1 << 4); /* TD */ |
| if (flags & ATMEL_SSC_RD) |
| pin_mask |= (1 << 5); /* RD */ |
| |
| if (pin_mask > 0) |
| select_peripheral(PIOA, pin_mask, PERIPH_B, 0); |
| |
| break; |
| case 2: |
| pdev = &ssc2_device; |
| if (flags & ATMEL_SSC_TD) |
| pin_mask |= (1 << 13); /* TD */ |
| if (flags & ATMEL_SSC_RD) |
| pin_mask |= (1 << 14); /* RD */ |
| if (flags & ATMEL_SSC_TK) |
| pin_mask |= (1 << 15); /* TK */ |
| if (flags & ATMEL_SSC_TF) |
| pin_mask |= (1 << 16); /* TF */ |
| if (flags & ATMEL_SSC_RF) |
| pin_mask |= (1 << 17); /* RF */ |
| if (flags & ATMEL_SSC_RK) |
| pin_mask |= (1 << 18); /* RK */ |
| |
| if (pin_mask > 0) |
| select_peripheral(PIOB, pin_mask, PERIPH_A, 0); |
| |
| break; |
| default: |
| return NULL; |
| } |
| |
| platform_device_register(pdev); |
| return pdev; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * USB Device Controller |
| * -------------------------------------------------------------------- */ |
| static struct resource usba0_resource[] __initdata = { |
| { |
| .start = 0xff300000, |
| .end = 0xff3fffff, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0xfff03000, |
| .end = 0xfff033ff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(31), |
| }; |
| static struct clk usba0_pclk = { |
| .name = "pclk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 12, |
| }; |
| static struct clk usba0_hclk = { |
| .name = "hclk", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = hsb_clk_get_rate, |
| .index = 6, |
| }; |
| |
| #define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ |
| [idx] = { \ |
| .name = nam, \ |
| .index = idx, \ |
| .fifo_size = maxpkt, \ |
| .nr_banks = maxbk, \ |
| .can_dma = dma, \ |
| .can_isoc = isoc, \ |
| } |
| |
| static struct usba_ep_data at32_usba_ep[] __initdata = { |
| EP("ep0", 0, 64, 1, 0, 0), |
| EP("ep1", 1, 512, 2, 1, 1), |
| EP("ep2", 2, 512, 2, 1, 1), |
| EP("ep3-int", 3, 64, 3, 1, 0), |
| EP("ep4-int", 4, 64, 3, 1, 0), |
| EP("ep5", 5, 1024, 3, 1, 1), |
| EP("ep6", 6, 1024, 3, 1, 1), |
| }; |
| |
| #undef EP |
| |
| struct platform_device *__init |
| at32_add_device_usba(unsigned int id, struct usba_platform_data *data) |
| { |
| /* |
| * pdata doesn't have room for any endpoints, so we need to |
| * append room for the ones we need right after it. |
| */ |
| struct { |
| struct usba_platform_data pdata; |
| struct usba_ep_data ep[7]; |
| } usba_data; |
| struct platform_device *pdev; |
| |
| if (id != 0) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_usba_udc", 0); |
| if (!pdev) |
| return NULL; |
| |
| if (platform_device_add_resources(pdev, usba0_resource, |
| ARRAY_SIZE(usba0_resource))) |
| goto out_free_pdev; |
| |
| if (data) { |
| usba_data.pdata.vbus_pin = data->vbus_pin; |
| usba_data.pdata.vbus_pin_inverted = data->vbus_pin_inverted; |
| } else { |
| usba_data.pdata.vbus_pin = -EINVAL; |
| usba_data.pdata.vbus_pin_inverted = -EINVAL; |
| } |
| |
| data = &usba_data.pdata; |
| data->num_ep = ARRAY_SIZE(at32_usba_ep); |
| memcpy(data->ep, at32_usba_ep, sizeof(at32_usba_ep)); |
| |
| if (platform_device_add_data(pdev, data, sizeof(usba_data))) |
| goto out_free_pdev; |
| |
| if (gpio_is_valid(data->vbus_pin)) |
| at32_select_gpio(data->vbus_pin, 0); |
| |
| usba0_pclk.dev = &pdev->dev; |
| usba0_hclk.dev = &pdev->dev; |
| |
| platform_device_add(pdev); |
| |
| return pdev; |
| |
| out_free_pdev: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * IDE / CompactFlash |
| * -------------------------------------------------------------------- */ |
| #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7001) |
| static struct resource at32_smc_cs4_resource[] __initdata = { |
| { |
| .start = 0x04000000, |
| .end = 0x07ffffff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(~0UL), /* Magic IRQ will be overridden */ |
| }; |
| static struct resource at32_smc_cs5_resource[] __initdata = { |
| { |
| .start = 0x20000000, |
| .end = 0x23ffffff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(~0UL), /* Magic IRQ will be overridden */ |
| }; |
| |
| static int __init at32_init_ide_or_cf(struct platform_device *pdev, |
| unsigned int cs, unsigned int extint) |
| { |
| static unsigned int extint_pin_map[4] __initdata = { |
| (1 << 25), |
| (1 << 26), |
| (1 << 27), |
| (1 << 28), |
| }; |
| static bool common_pins_initialized __initdata = false; |
| unsigned int extint_pin; |
| int ret; |
| u32 pin_mask; |
| |
| if (extint >= ARRAY_SIZE(extint_pin_map)) |
| return -EINVAL; |
| extint_pin = extint_pin_map[extint]; |
| |
| switch (cs) { |
| case 4: |
| ret = platform_device_add_resources(pdev, |
| at32_smc_cs4_resource, |
| ARRAY_SIZE(at32_smc_cs4_resource)); |
| if (ret) |
| return ret; |
| |
| /* NCS4 -> OE_N */ |
| select_peripheral(PIOE, (1 << 21), PERIPH_A, 0); |
| hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF0_ENABLE); |
| break; |
| case 5: |
| ret = platform_device_add_resources(pdev, |
| at32_smc_cs5_resource, |
| ARRAY_SIZE(at32_smc_cs5_resource)); |
| if (ret) |
| return ret; |
| |
| /* NCS5 -> OE_N */ |
| select_peripheral(PIOE, (1 << 22), PERIPH_A, 0); |
| hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF1_ENABLE); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (!common_pins_initialized) { |
| pin_mask = (1 << 19); /* CFCE1 -> CS0_N */ |
| pin_mask |= (1 << 20); /* CFCE2 -> CS1_N */ |
| pin_mask |= (1 << 23); /* CFRNW -> DIR */ |
| pin_mask |= (1 << 24); /* NWAIT <- IORDY */ |
| |
| select_peripheral(PIOE, pin_mask, PERIPH_A, 0); |
| |
| common_pins_initialized = true; |
| } |
| |
| select_peripheral(PIOB, extint_pin, PERIPH_A, AT32_GPIOF_DEGLITCH); |
| |
| pdev->resource[1].start = EIM_IRQ_BASE + extint; |
| pdev->resource[1].end = pdev->resource[1].start; |
| |
| return 0; |
| } |
| |
| struct platform_device *__init |
| at32_add_device_ide(unsigned int id, unsigned int extint, |
| struct ide_platform_data *data) |
| { |
| struct platform_device *pdev; |
| |
| pdev = platform_device_alloc("at32_ide", id); |
| if (!pdev) |
| goto fail; |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct ide_platform_data))) |
| goto fail; |
| |
| if (at32_init_ide_or_cf(pdev, data->cs, extint)) |
| goto fail; |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| fail: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| struct platform_device *__init |
| at32_add_device_cf(unsigned int id, unsigned int extint, |
| struct cf_platform_data *data) |
| { |
| struct platform_device *pdev; |
| |
| pdev = platform_device_alloc("at32_cf", id); |
| if (!pdev) |
| goto fail; |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct cf_platform_data))) |
| goto fail; |
| |
| if (at32_init_ide_or_cf(pdev, data->cs, extint)) |
| goto fail; |
| |
| if (gpio_is_valid(data->detect_pin)) |
| at32_select_gpio(data->detect_pin, AT32_GPIOF_DEGLITCH); |
| if (gpio_is_valid(data->reset_pin)) |
| at32_select_gpio(data->reset_pin, 0); |
| if (gpio_is_valid(data->vcc_pin)) |
| at32_select_gpio(data->vcc_pin, 0); |
| /* READY is used as extint, so we can't select it as gpio */ |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| fail: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| #endif |
| |
| /* -------------------------------------------------------------------- |
| * NAND Flash / SmartMedia |
| * -------------------------------------------------------------------- */ |
| static struct resource smc_cs3_resource[] __initdata = { |
| { |
| .start = 0x0c000000, |
| .end = 0x0fffffff, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0xfff03c00, |
| .end = 0xfff03fff, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_nand(unsigned int id, struct atmel_nand_data *data) |
| { |
| struct platform_device *pdev; |
| |
| if (id != 0 || !data) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_nand", id); |
| if (!pdev) |
| goto fail; |
| |
| if (platform_device_add_resources(pdev, smc_cs3_resource, |
| ARRAY_SIZE(smc_cs3_resource))) |
| goto fail; |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct atmel_nand_data))) |
| goto fail; |
| |
| hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_NAND_ENABLE); |
| if (data->enable_pin) |
| at32_select_gpio(data->enable_pin, |
| AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH); |
| if (data->rdy_pin) |
| at32_select_gpio(data->rdy_pin, 0); |
| if (data->det_pin) |
| at32_select_gpio(data->det_pin, 0); |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| fail: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * AC97C |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_ac97c0_resource[] __initdata = { |
| PBMEM(0xfff02800), |
| IRQ(29), |
| }; |
| static struct clk atmel_ac97c0_pclk = { |
| .name = "pclk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 10, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data, |
| unsigned int flags) |
| { |
| struct platform_device *pdev; |
| struct dw_dma_slave *rx_dws; |
| struct dw_dma_slave *tx_dws; |
| struct ac97c_platform_data _data; |
| u32 pin_mask; |
| |
| if (id != 0) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_ac97c", id); |
| if (!pdev) |
| return NULL; |
| |
| if (platform_device_add_resources(pdev, atmel_ac97c0_resource, |
| ARRAY_SIZE(atmel_ac97c0_resource))) |
| goto out_free_resources; |
| |
| if (!data) { |
| data = &_data; |
| memset(data, 0, sizeof(struct ac97c_platform_data)); |
| data->reset_pin = -ENODEV; |
| } |
| |
| rx_dws = &data->rx_dws; |
| tx_dws = &data->tx_dws; |
| |
| /* Check if DMA slave interface for capture should be configured. */ |
| if (flags & AC97C_CAPTURE) { |
| rx_dws->dma_dev = &dw_dmac0_device.dev; |
| rx_dws->cfg_hi = DWC_CFGH_SRC_PER(3); |
| rx_dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL); |
| rx_dws->src_master = 0; |
| rx_dws->dst_master = 1; |
| } |
| |
| /* Check if DMA slave interface for playback should be configured. */ |
| if (flags & AC97C_PLAYBACK) { |
| tx_dws->dma_dev = &dw_dmac0_device.dev; |
| tx_dws->cfg_hi = DWC_CFGH_DST_PER(4); |
| tx_dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL); |
| tx_dws->src_master = 0; |
| tx_dws->dst_master = 1; |
| } |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct ac97c_platform_data))) |
| goto out_free_resources; |
| |
| /* SDO | SYNC | SCLK | SDI */ |
| pin_mask = (1 << 20) | (1 << 21) | (1 << 22) | (1 << 23); |
| |
| select_peripheral(PIOB, pin_mask, PERIPH_B, 0); |
| |
| if (gpio_is_valid(data->reset_pin)) |
| at32_select_gpio(data->reset_pin, AT32_GPIOF_OUTPUT |
| | AT32_GPIOF_HIGH); |
| |
| atmel_ac97c0_pclk.dev = &pdev->dev; |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| out_free_resources: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * ABDAC |
| * -------------------------------------------------------------------- */ |
| static struct resource abdac0_resource[] __initdata = { |
| PBMEM(0xfff02000), |
| IRQ(27), |
| }; |
| static struct clk abdac0_pclk = { |
| .name = "pclk", |
| .parent = &pbb_clk, |
| .mode = pbb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .index = 8, |
| }; |
| static struct clk abdac0_sample_clk = { |
| .name = "sample_clk", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 6, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_abdac(unsigned int id, struct atmel_abdac_pdata *data) |
| { |
| struct platform_device *pdev; |
| struct dw_dma_slave *dws; |
| u32 pin_mask; |
| |
| if (id != 0 || !data) |
| return NULL; |
| |
| pdev = platform_device_alloc("atmel_abdac", id); |
| if (!pdev) |
| return NULL; |
| |
| if (platform_device_add_resources(pdev, abdac0_resource, |
| ARRAY_SIZE(abdac0_resource))) |
| goto out_free_resources; |
| |
| dws = &data->dws; |
| |
| dws->dma_dev = &dw_dmac0_device.dev; |
| dws->cfg_hi = DWC_CFGH_DST_PER(2); |
| dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL); |
| dws->src_master = 0; |
| dws->dst_master = 1; |
| |
| if (platform_device_add_data(pdev, data, |
| sizeof(struct atmel_abdac_pdata))) |
| goto out_free_resources; |
| |
| pin_mask = (1 << 20) | (1 << 22); /* DATA1 & DATAN1 */ |
| pin_mask |= (1 << 21) | (1 << 23); /* DATA0 & DATAN0 */ |
| |
| select_peripheral(PIOB, pin_mask, PERIPH_A, 0); |
| |
| abdac0_pclk.dev = &pdev->dev; |
| abdac0_sample_clk.dev = &pdev->dev; |
| |
| platform_device_add(pdev); |
| return pdev; |
| |
| out_free_resources: |
| platform_device_put(pdev); |
| return NULL; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * GCLK |
| * -------------------------------------------------------------------- */ |
| static struct clk gclk0 = { |
| .name = "gclk0", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 0, |
| }; |
| static struct clk gclk1 = { |
| .name = "gclk1", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 1, |
| }; |
| static struct clk gclk2 = { |
| .name = "gclk2", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 2, |
| }; |
| static struct clk gclk3 = { |
| .name = "gclk3", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 3, |
| }; |
| static struct clk gclk4 = { |
| .name = "gclk4", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 4, |
| }; |
| |
| static __initdata struct clk *init_clocks[] = { |
| &osc32k, |
| &osc0, |
| &osc1, |
| &pll0, |
| &pll1, |
| &cpu_clk, |
| &hsb_clk, |
| &pba_clk, |
| &pbb_clk, |
| &at32_pm_pclk, |
| &at32_intc0_pclk, |
| &at32_hmatrix_clk, |
| &ebi_clk, |
| &hramc_clk, |
| &sdramc_clk, |
| &smc0_pclk, |
| &smc0_mck, |
| &pdc_hclk, |
| &pdc_pclk, |
| &dw_dmac0_hclk, |
| &pico_clk, |
| &pio0_mck, |
| &pio1_mck, |
| &pio2_mck, |
| &pio3_mck, |
| &pio4_mck, |
| &at32_tcb0_t0_clk, |
| &at32_tcb1_t0_clk, |
| &atmel_psif0_pclk, |
| &atmel_psif1_pclk, |
| &atmel_usart0_usart, |
| &atmel_usart1_usart, |
| &atmel_usart2_usart, |
| &atmel_usart3_usart, |
| &atmel_pwm0_mck, |
| #if defined(CONFIG_CPU_AT32AP7000) |
| &macb0_hclk, |
| &macb0_pclk, |
| &macb1_hclk, |
| &macb1_pclk, |
| #endif |
| &atmel_spi0_spi_clk, |
| &atmel_spi1_spi_clk, |
| &atmel_twi0_pclk, |
| &atmel_mci0_pclk, |
| #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002) |
| &atmel_lcdfb0_hclk, |
| &atmel_lcdfb0_pixclk, |
| #endif |
| &ssc0_pclk, |
| &ssc1_pclk, |
| &ssc2_pclk, |
| &usba0_hclk, |
| &usba0_pclk, |
| &atmel_ac97c0_pclk, |
| &abdac0_pclk, |
| &abdac0_sample_clk, |
| &gclk0, |
| &gclk1, |
| &gclk2, |
| &gclk3, |
| &gclk4, |
| }; |
| |
| void __init setup_platform(void) |
| { |
| u32 cpu_mask = 0, hsb_mask = 0, pba_mask = 0, pbb_mask = 0; |
| int i; |
| |
| if (pm_readl(MCCTRL) & PM_BIT(PLLSEL)) { |
| main_clock = &pll0; |
| cpu_clk.parent = &pll0; |
| } else { |
| main_clock = &osc0; |
| cpu_clk.parent = &osc0; |
| } |
| |
| if (pm_readl(PLL0) & PM_BIT(PLLOSC)) |
| pll0.parent = &osc1; |
| if (pm_readl(PLL1) & PM_BIT(PLLOSC)) |
| pll1.parent = &osc1; |
| |
| genclk_init_parent(&gclk0); |
| genclk_init_parent(&gclk1); |
| genclk_init_parent(&gclk2); |
| genclk_init_parent(&gclk3); |
| genclk_init_parent(&gclk4); |
| #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002) |
| genclk_init_parent(&atmel_lcdfb0_pixclk); |
| #endif |
| genclk_init_parent(&abdac0_sample_clk); |
| |
| /* |
| * Build initial dynamic clock list by registering all clocks |
| * from the array. |
| * At the same time, turn on all clocks that have at least one |
| * user already, and turn off everything else. We only do this |
| * for module clocks, and even though it isn't particularly |
| * pretty to check the address of the mode function, it should |
| * do the trick... |
| */ |
| for (i = 0; i < ARRAY_SIZE(init_clocks); i++) { |
| struct clk *clk = init_clocks[i]; |
| |
| /* first, register clock */ |
| at32_clk_register(clk); |
| |
| if (clk->users == 0) |
| continue; |
| |
| if (clk->mode == &cpu_clk_mode) |
| cpu_mask |= 1 << clk->index; |
| else if (clk->mode == &hsb_clk_mode) |
| hsb_mask |= 1 << clk->index; |
| else if (clk->mode == &pba_clk_mode) |
| pba_mask |= 1 << clk->index; |
| else if (clk->mode == &pbb_clk_mode) |
| pbb_mask |= 1 << clk->index; |
| } |
| |
| pm_writel(CPU_MASK, cpu_mask); |
| pm_writel(HSB_MASK, hsb_mask); |
| pm_writel(PBA_MASK, pba_mask); |
| pm_writel(PBB_MASK, pbb_mask); |
| |
| /* Initialize the port muxes */ |
| at32_init_pio(&pio0_device); |
| at32_init_pio(&pio1_device); |
| at32_init_pio(&pio2_device); |
| at32_init_pio(&pio3_device); |
| at32_init_pio(&pio4_device); |
| } |
| |
| struct gen_pool *sram_pool; |
| |
| static int __init sram_init(void) |
| { |
| struct gen_pool *pool; |
| |
| /* 1KiB granularity */ |
| pool = gen_pool_create(10, -1); |
| if (!pool) |
| goto fail; |
| |
| if (gen_pool_add(pool, 0x24000000, 0x8000, -1)) |
| goto err_pool_add; |
| |
| sram_pool = pool; |
| return 0; |
| |
| err_pool_add: |
| gen_pool_destroy(pool); |
| fail: |
| pr_err("Failed to create SRAM pool\n"); |
| return -ENOMEM; |
| } |
| core_initcall(sram_init); |