| /* |
| * at91sam9g45.dtsi - Device Tree Include file for AT91SAM9G45 family SoC |
| * applies to AT91SAM9G45, AT91SAM9M10, |
| * AT91SAM9G46, AT91SAM9M11 SoC |
| * |
| * Copyright (C) 2011 Atmel, |
| * 2011 Nicolas Ferre <nicolas.ferre@atmel.com> |
| * |
| * Licensed under GPLv2 or later. |
| */ |
| |
| #include "skeleton.dtsi" |
| #include <dt-bindings/dma/at91.h> |
| #include <dt-bindings/pinctrl/at91.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/clock/at91.h> |
| |
| / { |
| model = "Atmel AT91SAM9G45 family SoC"; |
| compatible = "atmel,at91sam9g45"; |
| interrupt-parent = <&aic>; |
| |
| aliases { |
| serial0 = &dbgu; |
| serial1 = &usart0; |
| serial2 = &usart1; |
| serial3 = &usart2; |
| serial4 = &usart3; |
| gpio0 = &pioA; |
| gpio1 = &pioB; |
| gpio2 = &pioC; |
| gpio3 = &pioD; |
| gpio4 = &pioE; |
| tcb0 = &tcb0; |
| tcb1 = &tcb1; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| ssc0 = &ssc0; |
| ssc1 = &ssc1; |
| pwm0 = &pwm0; |
| }; |
| cpus { |
| #address-cells = <0>; |
| #size-cells = <0>; |
| |
| cpu { |
| compatible = "arm,arm926ej-s"; |
| device_type = "cpu"; |
| }; |
| }; |
| |
| memory { |
| reg = <0x70000000 0x10000000>; |
| }; |
| |
| clocks { |
| slow_xtal: slow_xtal { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| }; |
| |
| main_xtal: main_xtal { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| }; |
| |
| adc_op_clk: adc_op_clk{ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <300000>; |
| }; |
| }; |
| |
| ahb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| apb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| aic: interrupt-controller@fffff000 { |
| #interrupt-cells = <3>; |
| compatible = "atmel,at91rm9200-aic"; |
| interrupt-controller; |
| reg = <0xfffff000 0x200>; |
| atmel,external-irqs = <31>; |
| }; |
| |
| ramc0: ramc@ffffe400 { |
| compatible = "atmel,at91sam9g45-ddramc"; |
| reg = <0xffffe400 0x200>; |
| clocks = <&ddrck>; |
| clock-names = "ddrck"; |
| }; |
| |
| ramc1: ramc@ffffe600 { |
| compatible = "atmel,at91sam9g45-ddramc"; |
| reg = <0xffffe600 0x200>; |
| clocks = <&ddrck>; |
| clock-names = "ddrck"; |
| }; |
| |
| pmc: pmc@fffffc00 { |
| compatible = "atmel,at91sam9g45-pmc"; |
| reg = <0xfffffc00 0x100>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| interrupt-controller; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| main_osc: main_osc { |
| compatible = "atmel,at91rm9200-clk-main-osc"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_MOSCS>; |
| clocks = <&main_xtal>; |
| }; |
| |
| main: mainck { |
| compatible = "atmel,at91rm9200-clk-main"; |
| #clock-cells = <0>; |
| clocks = <&main_osc>; |
| }; |
| |
| plla: pllack { |
| compatible = "atmel,at91rm9200-clk-pll"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_LOCKA>; |
| clocks = <&main>; |
| reg = <0>; |
| atmel,clk-input-range = <2000000 32000000>; |
| #atmel,pll-clk-output-range-cells = <4>; |
| atmel,pll-clk-output-ranges = <745000000 800000000 0 0 |
| 695000000 750000000 1 0 |
| 645000000 700000000 2 0 |
| 595000000 650000000 3 0 |
| 545000000 600000000 0 1 |
| 495000000 555000000 1 1 |
| 445000000 500000000 2 1 |
| 400000000 450000000 3 1>; |
| }; |
| |
| plladiv: plladivck { |
| compatible = "atmel,at91sam9x5-clk-plldiv"; |
| #clock-cells = <0>; |
| clocks = <&plla>; |
| }; |
| |
| utmi: utmick { |
| compatible = "atmel,at91sam9x5-clk-utmi"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_LOCKU>; |
| clocks = <&main>; |
| }; |
| |
| mck: masterck { |
| compatible = "atmel,at91rm9200-clk-master"; |
| #clock-cells = <0>; |
| interrupts-extended = <&pmc AT91_PMC_MCKRDY>; |
| clocks = <&slow_xtal>, <&main>, <&plladiv>, <&utmi>; |
| atmel,clk-output-range = <0 133333333>; |
| atmel,clk-divisors = <1 2 4 3>; |
| }; |
| |
| usb: usbck { |
| compatible = "atmel,at91sam9x5-clk-usb"; |
| #clock-cells = <0>; |
| clocks = <&plladiv>, <&utmi>; |
| }; |
| |
| prog: progck { |
| compatible = "atmel,at91sam9g45-clk-programmable"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupt-parent = <&pmc>; |
| clocks = <&slow_xtal>, <&main>, <&plladiv>, <&utmi>, <&mck>; |
| |
| prog0: prog0 { |
| #clock-cells = <0>; |
| reg = <0>; |
| interrupts = <AT91_PMC_PCKRDY(0)>; |
| }; |
| |
| prog1: prog1 { |
| #clock-cells = <0>; |
| reg = <1>; |
| interrupts = <AT91_PMC_PCKRDY(1)>; |
| }; |
| }; |
| |
| systemck { |
| compatible = "atmel,at91rm9200-clk-system"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ddrck: ddrck { |
| #clock-cells = <0>; |
| reg = <2>; |
| clocks = <&mck>; |
| }; |
| |
| uhpck: uhpck { |
| #clock-cells = <0>; |
| reg = <6>; |
| clocks = <&usb>; |
| }; |
| |
| pck0: pck0 { |
| #clock-cells = <0>; |
| reg = <8>; |
| clocks = <&prog0>; |
| }; |
| |
| pck1: pck1 { |
| #clock-cells = <0>; |
| reg = <9>; |
| clocks = <&prog1>; |
| }; |
| }; |
| |
| periphck { |
| compatible = "atmel,at91rm9200-clk-peripheral"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&mck>; |
| |
| pioA_clk: pioA_clk { |
| #clock-cells = <0>; |
| reg = <2>; |
| }; |
| |
| pioB_clk: pioB_clk { |
| #clock-cells = <0>; |
| reg = <3>; |
| }; |
| |
| pioC_clk: pioC_clk { |
| #clock-cells = <0>; |
| reg = <4>; |
| }; |
| |
| pioDE_clk: pioDE_clk { |
| #clock-cells = <0>; |
| reg = <5>; |
| }; |
| |
| trng_clk: trng_clk { |
| #clock-cells = <0>; |
| reg = <6>; |
| }; |
| |
| usart0_clk: usart0_clk { |
| #clock-cells = <0>; |
| reg = <7>; |
| }; |
| |
| usart1_clk: usart1_clk { |
| #clock-cells = <0>; |
| reg = <8>; |
| }; |
| |
| usart2_clk: usart2_clk { |
| #clock-cells = <0>; |
| reg = <9>; |
| }; |
| |
| usart3_clk: usart3_clk { |
| #clock-cells = <0>; |
| reg = <10>; |
| }; |
| |
| mci0_clk: mci0_clk { |
| #clock-cells = <0>; |
| reg = <11>; |
| }; |
| |
| twi0_clk: twi0_clk { |
| #clock-cells = <0>; |
| reg = <12>; |
| }; |
| |
| twi1_clk: twi1_clk { |
| #clock-cells = <0>; |
| reg = <13>; |
| }; |
| |
| spi0_clk: spi0_clk { |
| #clock-cells = <0>; |
| reg = <14>; |
| }; |
| |
| spi1_clk: spi1_clk { |
| #clock-cells = <0>; |
| reg = <15>; |
| }; |
| |
| ssc0_clk: ssc0_clk { |
| #clock-cells = <0>; |
| reg = <16>; |
| }; |
| |
| ssc1_clk: ssc1_clk { |
| #clock-cells = <0>; |
| reg = <17>; |
| }; |
| |
| tcb0_clk: tcb0_clk { |
| #clock-cells = <0>; |
| reg = <18>; |
| }; |
| |
| pwm_clk: pwm_clk { |
| #clock-cells = <0>; |
| reg = <19>; |
| }; |
| |
| adc_clk: adc_clk { |
| #clock-cells = <0>; |
| reg = <20>; |
| }; |
| |
| dma0_clk: dma0_clk { |
| #clock-cells = <0>; |
| reg = <21>; |
| }; |
| |
| uhphs_clk: uhphs_clk { |
| #clock-cells = <0>; |
| reg = <22>; |
| }; |
| |
| lcd_clk: lcd_clk { |
| #clock-cells = <0>; |
| reg = <23>; |
| }; |
| |
| ac97_clk: ac97_clk { |
| #clock-cells = <0>; |
| reg = <24>; |
| }; |
| |
| macb0_clk: macb0_clk { |
| #clock-cells = <0>; |
| reg = <25>; |
| }; |
| |
| isi_clk: isi_clk { |
| #clock-cells = <0>; |
| reg = <26>; |
| }; |
| |
| udphs_clk: udphs_clk { |
| #clock-cells = <0>; |
| reg = <27>; |
| }; |
| |
| aestdessha_clk: aestdessha_clk { |
| #clock-cells = <0>; |
| reg = <28>; |
| }; |
| |
| mci1_clk: mci1_clk { |
| #clock-cells = <0>; |
| reg = <29>; |
| }; |
| |
| vdec_clk: vdec_clk { |
| #clock-cells = <0>; |
| reg = <30>; |
| }; |
| }; |
| }; |
| |
| rstc@fffffd00 { |
| compatible = "atmel,at91sam9g45-rstc"; |
| reg = <0xfffffd00 0x10>; |
| }; |
| |
| pit: timer@fffffd30 { |
| compatible = "atmel,at91sam9260-pit"; |
| reg = <0xfffffd30 0xf>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| clocks = <&mck>; |
| }; |
| |
| |
| shdwc@fffffd10 { |
| compatible = "atmel,at91sam9rl-shdwc"; |
| reg = <0xfffffd10 0x10>; |
| }; |
| |
| tcb0: timer@fff7c000 { |
| compatible = "atmel,at91rm9200-tcb"; |
| reg = <0xfff7c000 0x100>; |
| interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>; |
| clock-names = "t0_clk", "t1_clk", "t2_clk"; |
| }; |
| |
| tcb1: timer@fffd4000 { |
| compatible = "atmel,at91rm9200-tcb"; |
| reg = <0xfffd4000 0x100>; |
| interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>; |
| clock-names = "t0_clk", "t1_clk", "t2_clk"; |
| }; |
| |
| dma: dma-controller@ffffec00 { |
| compatible = "atmel,at91sam9g45-dma"; |
| reg = <0xffffec00 0x200>; |
| interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>; |
| #dma-cells = <2>; |
| clocks = <&dma0_clk>; |
| clock-names = "dma_clk"; |
| }; |
| |
| pinctrl@fffff200 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; |
| ranges = <0xfffff200 0xfffff200 0xa00>; |
| |
| atmel,mux-mask = < |
| /* A B */ |
| 0xffffffff 0xffc003ff /* pioA */ |
| 0xffffffff 0x800f8f00 /* pioB */ |
| 0xffffffff 0x00000e00 /* pioC */ |
| 0xffffffff 0xff0c1381 /* pioD */ |
| 0xffffffff 0x81ffff81 /* pioE */ |
| >; |
| |
| /* shared pinctrl settings */ |
| adc0 { |
| pinctrl_adc0_adtrg: adc0_adtrg { |
| atmel,pins = <AT91_PIOD 28 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad0: adc0_ad0 { |
| atmel,pins = <AT91_PIOD 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad1: adc0_ad1 { |
| atmel,pins = <AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad2: adc0_ad2 { |
| atmel,pins = <AT91_PIOD 22 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad3: adc0_ad3 { |
| atmel,pins = <AT91_PIOD 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad4: adc0_ad4 { |
| atmel,pins = <AT91_PIOD 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad5: adc0_ad5 { |
| atmel,pins = <AT91_PIOD 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad6: adc0_ad6 { |
| atmel,pins = <AT91_PIOD 26 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| pinctrl_adc0_ad7: adc0_ad7 { |
| atmel,pins = <AT91_PIOD 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| dbgu { |
| pinctrl_dbgu: dbgu-0 { |
| atmel,pins = |
| <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB12 periph A */ |
| AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB13 periph A */ |
| }; |
| }; |
| |
| i2c0 { |
| pinctrl_i2c0: i2c0-0 { |
| atmel,pins = |
| <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA21 periph A TWCK0 */ |
| AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA20 periph A TWD0 */ |
| }; |
| }; |
| |
| i2c1 { |
| pinctrl_i2c1: i2c1-0 { |
| atmel,pins = |
| <AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB11 periph A TWCK1 */ |
| AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB10 periph A TWD1 */ |
| }; |
| }; |
| |
| usart0 { |
| pinctrl_usart0: usart0-0 { |
| atmel,pins = |
| <AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB19 periph A with pullup */ |
| AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB18 periph A */ |
| }; |
| |
| pinctrl_usart0_rts: usart0_rts-0 { |
| atmel,pins = |
| <AT91_PIOB 17 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB17 periph B */ |
| }; |
| |
| pinctrl_usart0_cts: usart0_cts-0 { |
| atmel,pins = |
| <AT91_PIOB 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB15 periph B */ |
| }; |
| }; |
| |
| uart1 { |
| pinctrl_usart1: usart1-0 { |
| atmel,pins = |
| <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB4 periph A with pullup */ |
| AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB5 periph A */ |
| }; |
| |
| pinctrl_usart1_rts: usart1_rts-0 { |
| atmel,pins = |
| <AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD16 periph A */ |
| }; |
| |
| pinctrl_usart1_cts: usart1_cts-0 { |
| atmel,pins = |
| <AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD17 periph A */ |
| }; |
| }; |
| |
| usart2 { |
| pinctrl_usart2: usart2-0 { |
| atmel,pins = |
| <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB6 periph A with pullup */ |
| AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB7 periph A */ |
| }; |
| |
| pinctrl_usart2_rts: usart2_rts-0 { |
| atmel,pins = |
| <AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC9 periph B */ |
| }; |
| |
| pinctrl_usart2_cts: usart2_cts-0 { |
| atmel,pins = |
| <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC11 periph B */ |
| }; |
| }; |
| |
| usart3 { |
| pinctrl_usart3: usart3-0 { |
| atmel,pins = |
| <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PB9 periph A with pullup */ |
| AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB8 periph A */ |
| }; |
| |
| pinctrl_usart3_rts: usart3_rts-0 { |
| atmel,pins = |
| <AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA23 periph B */ |
| }; |
| |
| pinctrl_usart3_cts: usart3_cts-0 { |
| atmel,pins = |
| <AT91_PIOA 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA24 periph B */ |
| }; |
| }; |
| |
| nand { |
| pinctrl_nand: nand-0 { |
| atmel,pins = |
| <AT91_PIOC 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PC8 gpio RDY pin pull_up*/ |
| AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PC14 gpio enable pin pull_up */ |
| }; |
| }; |
| |
| macb { |
| pinctrl_macb_rmii: macb_rmii-0 { |
| atmel,pins = |
| <AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA10 periph A */ |
| AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA11 periph A */ |
| AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA12 periph A */ |
| AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA13 periph A */ |
| AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA14 periph A */ |
| AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA15 periph A */ |
| AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA16 periph A */ |
| AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA17 periph A */ |
| AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA18 periph A */ |
| AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA19 periph A */ |
| }; |
| |
| pinctrl_macb_rmii_mii: macb_rmii_mii-0 { |
| atmel,pins = |
| <AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA6 periph B */ |
| AT91_PIOA 7 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA7 periph B */ |
| AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA8 periph B */ |
| AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA9 periph B */ |
| AT91_PIOA 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA27 periph B */ |
| AT91_PIOA 28 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA28 periph B */ |
| AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA29 periph B */ |
| AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA30 periph B */ |
| }; |
| }; |
| |
| mmc0 { |
| pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 { |
| atmel,pins = |
| <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA0 periph A */ |
| AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA1 periph A with pullup */ |
| AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA2 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { |
| atmel,pins = |
| <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA3 periph A with pullup */ |
| AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA4 periph A with pullup */ |
| AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA5 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 { |
| atmel,pins = |
| <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA6 periph A with pullup */ |
| AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA7 periph A with pullup */ |
| AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA8 periph A with pullup */ |
| AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA9 periph A with pullup */ |
| }; |
| }; |
| |
| mmc1 { |
| pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 { |
| atmel,pins = |
| <AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA31 periph A */ |
| AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA22 periph A with pullup */ |
| AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA23 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 { |
| atmel,pins = |
| <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA24 periph A with pullup */ |
| AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA25 periph A with pullup */ |
| AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA26 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc1_slot0_dat4_7: mmc1_slot0_dat4_7-0 { |
| atmel,pins = |
| <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA27 periph A with pullup */ |
| AT91_PIOA 28 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA28 periph A with pullup */ |
| AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA29 periph A with pullup */ |
| AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA30 periph A with pullup */ |
| }; |
| }; |
| |
| ssc0 { |
| pinctrl_ssc0_tx: ssc0_tx-0 { |
| atmel,pins = |
| <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD0 periph A */ |
| AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD1 periph A */ |
| AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD2 periph A */ |
| }; |
| |
| pinctrl_ssc0_rx: ssc0_rx-0 { |
| atmel,pins = |
| <AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD3 periph A */ |
| AT91_PIOD 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD4 periph A */ |
| AT91_PIOD 5 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD5 periph A */ |
| }; |
| }; |
| |
| ssc1 { |
| pinctrl_ssc1_tx: ssc1_tx-0 { |
| atmel,pins = |
| <AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD10 periph A */ |
| AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD11 periph A */ |
| AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD12 periph A */ |
| }; |
| |
| pinctrl_ssc1_rx: ssc1_rx-0 { |
| atmel,pins = |
| <AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD13 periph A */ |
| AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD14 periph A */ |
| AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD15 periph A */ |
| }; |
| }; |
| |
| spi0 { |
| pinctrl_spi0: spi0-0 { |
| atmel,pins = |
| <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB0 periph A SPI0_MISO pin */ |
| AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB1 periph A SPI0_MOSI pin */ |
| AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB2 periph A SPI0_SPCK pin */ |
| }; |
| }; |
| |
| spi1 { |
| pinctrl_spi1: spi1-0 { |
| atmel,pins = |
| <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB14 periph A SPI1_MISO pin */ |
| AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB15 periph A SPI1_MOSI pin */ |
| AT91_PIOB 16 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB16 periph A SPI1_SPCK pin */ |
| }; |
| }; |
| |
| tcb0 { |
| pinctrl_tcb0_tclk0: tcb0_tclk0-0 { |
| atmel,pins = <AT91_PIOD 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tclk1: tcb0_tclk1-0 { |
| atmel,pins = <AT91_PIOD 29 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tclk2: tcb0_tclk2-0 { |
| atmel,pins = <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa0: tcb0_tioa0-0 { |
| atmel,pins = <AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa1: tcb0_tioa1-0 { |
| atmel,pins = <AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tioa2: tcb0_tioa2-0 { |
| atmel,pins = <AT91_PIOD 22 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob0: tcb0_tiob0-0 { |
| atmel,pins = <AT91_PIOD 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob1: tcb0_tiob1-0 { |
| atmel,pins = <AT91_PIOD 31 AT91_PERIPH_A AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb0_tiob2: tcb0_tiob2-0 { |
| atmel,pins = <AT91_PIOA 26 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| tcb1 { |
| pinctrl_tcb1_tclk0: tcb1_tclk0-0 { |
| atmel,pins = <AT91_PIOA 0 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tclk1: tcb1_tclk1-0 { |
| atmel,pins = <AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tclk2: tcb1_tclk2-0 { |
| atmel,pins = <AT91_PIOD 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tioa0: tcb1_tioa0-0 { |
| atmel,pins = <AT91_PIOA 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tioa1: tcb1_tioa1-0 { |
| atmel,pins = <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tioa2: tcb1_tioa2-0 { |
| atmel,pins = <AT91_PIOD 7 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tiob0: tcb1_tiob0-0 { |
| atmel,pins = <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tiob1: tcb1_tiob1-0 { |
| atmel,pins = <AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| |
| pinctrl_tcb1_tiob2: tcb1_tiob2-0 { |
| atmel,pins = <AT91_PIOD 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| }; |
| }; |
| |
| fb { |
| pinctrl_fb: fb-0 { |
| atmel,pins = |
| <AT91_PIOE 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE0 periph A */ |
| AT91_PIOE 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE2 periph A */ |
| AT91_PIOE 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE3 periph A */ |
| AT91_PIOE 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE4 periph A */ |
| AT91_PIOE 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE5 periph A */ |
| AT91_PIOE 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE6 periph A */ |
| AT91_PIOE 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE7 periph A */ |
| AT91_PIOE 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE8 periph A */ |
| AT91_PIOE 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE9 periph A */ |
| AT91_PIOE 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE10 periph A */ |
| AT91_PIOE 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE11 periph A */ |
| AT91_PIOE 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE12 periph A */ |
| AT91_PIOE 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE13 periph A */ |
| AT91_PIOE 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE14 periph A */ |
| AT91_PIOE 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE15 periph A */ |
| AT91_PIOE 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE16 periph A */ |
| AT91_PIOE 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE17 periph A */ |
| AT91_PIOE 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE18 periph A */ |
| AT91_PIOE 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE19 periph A */ |
| AT91_PIOE 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE20 periph A */ |
| AT91_PIOE 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE21 periph A */ |
| AT91_PIOE 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE22 periph A */ |
| AT91_PIOE 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE23 periph A */ |
| AT91_PIOE 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE24 periph A */ |
| AT91_PIOE 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE25 periph A */ |
| AT91_PIOE 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE26 periph A */ |
| AT91_PIOE 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE27 periph A */ |
| AT91_PIOE 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE28 periph A */ |
| AT91_PIOE 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* PE29 periph A */ |
| AT91_PIOE 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PE30 periph A */ |
| }; |
| }; |
| |
| pioA: gpio@fffff200 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff200 0x200>; |
| interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioA_clk>; |
| }; |
| |
| pioB: gpio@fffff400 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff400 0x200>; |
| interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioB_clk>; |
| }; |
| |
| pioC: gpio@fffff600 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff600 0x200>; |
| interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioC_clk>; |
| }; |
| |
| pioD: gpio@fffff800 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffff800 0x200>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioDE_clk>; |
| }; |
| |
| pioE: gpio@fffffa00 { |
| compatible = "atmel,at91rm9200-gpio"; |
| reg = <0xfffffa00 0x200>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pioDE_clk>; |
| }; |
| }; |
| |
| dbgu: serial@ffffee00 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xffffee00 0x200>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_dbgu>; |
| clocks = <&mck>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart0: serial@fff8c000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfff8c000 0x200>; |
| interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart0>; |
| clocks = <&usart0_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart1: serial@fff90000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfff90000 0x200>; |
| interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart1>; |
| clocks = <&usart1_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart2: serial@fff94000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfff94000 0x200>; |
| interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart2>; |
| clocks = <&usart2_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| usart3: serial@fff98000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfff98000 0x200>; |
| interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart3>; |
| clocks = <&usart3_clk>; |
| clock-names = "usart"; |
| status = "disabled"; |
| }; |
| |
| macb0: ethernet@fffbc000 { |
| compatible = "cdns,at32ap7000-macb", "cdns,macb"; |
| reg = <0xfffbc000 0x100>; |
| interrupts = <25 IRQ_TYPE_LEVEL_HIGH 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_macb_rmii>; |
| clocks = <&macb0_clk>, <&macb0_clk>; |
| clock-names = "hclk", "pclk"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@fff84000 { |
| compatible = "atmel,at91sam9g10-i2c"; |
| reg = <0xfff84000 0x100>; |
| interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&twi0_clk>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@fff88000 { |
| compatible = "atmel,at91sam9g10-i2c"; |
| reg = <0xfff88000 0x100>; |
| interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&twi1_clk>; |
| status = "disabled"; |
| }; |
| |
| ssc0: ssc@fff9c000 { |
| compatible = "atmel,at91sam9g45-ssc"; |
| reg = <0xfff9c000 0x4000>; |
| interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; |
| clocks = <&ssc0_clk>; |
| clock-names = "pclk"; |
| status = "disabled"; |
| }; |
| |
| ssc1: ssc@fffa0000 { |
| compatible = "atmel,at91sam9g45-ssc"; |
| reg = <0xfffa0000 0x4000>; |
| interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; |
| clocks = <&ssc1_clk>; |
| clock-names = "pclk"; |
| status = "disabled"; |
| }; |
| |
| adc0: adc@fffb0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91sam9g45-adc"; |
| reg = <0xfffb0000 0x100>; |
| interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&adc_clk>, <&adc_op_clk>; |
| clock-names = "adc_clk", "adc_op_clk"; |
| atmel,adc-channels-used = <0xff>; |
| atmel,adc-vref = <3300>; |
| atmel,adc-startup-time = <40>; |
| atmel,adc-res = <8 10>; |
| atmel,adc-res-names = "lowres", "highres"; |
| atmel,adc-use-res = "highres"; |
| |
| trigger@0 { |
| reg = <0>; |
| trigger-name = "external-rising"; |
| trigger-value = <0x1>; |
| trigger-external; |
| }; |
| trigger@1 { |
| reg = <1>; |
| trigger-name = "external-falling"; |
| trigger-value = <0x2>; |
| trigger-external; |
| }; |
| |
| trigger@2 { |
| reg = <2>; |
| trigger-name = "external-any"; |
| trigger-value = <0x3>; |
| trigger-external; |
| }; |
| |
| trigger@3 { |
| reg = <3>; |
| trigger-name = "continuous"; |
| trigger-value = <0x6>; |
| }; |
| }; |
| |
| pwm0: pwm@fffb8000 { |
| compatible = "atmel,at91sam9rl-pwm"; |
| reg = <0xfffb8000 0x300>; |
| interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; |
| #pwm-cells = <3>; |
| clocks = <&pwm_clk>; |
| status = "disabled"; |
| }; |
| |
| mmc0: mmc@fff80000 { |
| compatible = "atmel,hsmci"; |
| reg = <0xfff80000 0x600>; |
| interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>; |
| pinctrl-names = "default"; |
| dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>; |
| dma-names = "rxtx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&mci0_clk>; |
| clock-names = "mci_clk"; |
| status = "disabled"; |
| }; |
| |
| mmc1: mmc@fffd0000 { |
| compatible = "atmel,hsmci"; |
| reg = <0xfffd0000 0x600>; |
| interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>; |
| pinctrl-names = "default"; |
| dmas = <&dma 1 AT91_DMA_CFG_PER_ID(13)>; |
| dma-names = "rxtx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&mci1_clk>; |
| clock-names = "mci_clk"; |
| status = "disabled"; |
| }; |
| |
| watchdog@fffffd40 { |
| compatible = "atmel,at91sam9260-wdt"; |
| reg = <0xfffffd40 0x10>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; |
| atmel,watchdog-type = "hardware"; |
| atmel,reset-type = "all"; |
| atmel,dbg-halt; |
| atmel,idle-halt; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@fffa4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91rm9200-spi"; |
| reg = <0xfffa4000 0x200>; |
| interrupts = <14 4 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi0>; |
| clocks = <&spi0_clk>; |
| clock-names = "spi_clk"; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@fffa8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91rm9200-spi"; |
| reg = <0xfffa8000 0x200>; |
| interrupts = <15 4 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi1>; |
| clocks = <&spi1_clk>; |
| clock-names = "spi_clk"; |
| status = "disabled"; |
| }; |
| |
| usb2: gadget@fff78000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "atmel,at91sam9rl-udc"; |
| reg = <0x00600000 0x80000 |
| 0xfff78000 0x400>; |
| interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>; |
| clocks = <&udphs_clk>, <&utmi>; |
| clock-names = "pclk", "hclk"; |
| status = "disabled"; |
| |
| ep0 { |
| reg = <0>; |
| atmel,fifo-size = <64>; |
| atmel,nb-banks = <1>; |
| }; |
| |
| ep1 { |
| reg = <1>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <2>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep2 { |
| reg = <2>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <2>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep3 { |
| reg = <3>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| }; |
| |
| ep4 { |
| reg = <4>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| }; |
| |
| ep5 { |
| reg = <5>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| |
| ep6 { |
| reg = <6>; |
| atmel,fifo-size = <1024>; |
| atmel,nb-banks = <3>; |
| atmel,can-dma; |
| atmel,can-isoc; |
| }; |
| }; |
| }; |
| |
| fb0: fb@0x00500000 { |
| compatible = "atmel,at91sam9g45-lcdc"; |
| reg = <0x00500000 0x1000>; |
| interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fb>; |
| clocks = <&lcd_clk>, <&lcd_clk>; |
| clock-names = "hclk", "lcdc_clk"; |
| status = "disabled"; |
| }; |
| |
| nand0: nand@40000000 { |
| compatible = "atmel,at91rm9200-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x40000000 0x10000000 |
| 0xffffe200 0x200 |
| >; |
| atmel,nand-addr-offset = <21>; |
| atmel,nand-cmd-offset = <22>; |
| atmel,nand-has-dma; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_nand>; |
| gpios = <&pioC 8 GPIO_ACTIVE_HIGH |
| &pioC 14 GPIO_ACTIVE_HIGH |
| 0 |
| >; |
| status = "disabled"; |
| }; |
| |
| usb0: ohci@00700000 { |
| compatible = "atmel,at91rm9200-ohci", "usb-ohci"; |
| reg = <0x00700000 0x100000>; |
| interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; |
| //TODO |
| clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; |
| clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck"; |
| status = "disabled"; |
| }; |
| |
| usb1: ehci@00800000 { |
| compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; |
| reg = <0x00800000 0x100000>; |
| interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; |
| //TODO |
| clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; |
| clock-names = "usb_clk", "ehci_clk", "hclk", "uhpck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| i2c@0 { |
| compatible = "i2c-gpio"; |
| gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */ |
| &pioA 21 GPIO_ACTIVE_HIGH /* scl */ |
| >; |
| i2c-gpio,sda-open-drain; |
| i2c-gpio,scl-open-drain; |
| i2c-gpio,delay-us = <5>; /* ~100 kHz */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |